Agilent 16702 reader has with CVI?

Similar Questions

• Can someone help me on action with agilent 34970-34901 has continious

  I need assistance with 34970-34910 has continious measurements. Everyone says that you need to configure "Agilent 34970 has advanced Scan.vi". I have modified this vi to measure temperature and pressure (current) but I could not go a sterp before measuring very. How can I do this? I have attached the vi that I modified.

  I solved the issue of measuring continuous with Agilent 34970-34901 has. All my error is in the configuration of the usb serial port. To the continuous measurement, the flow of control of the usb serial port configuration must be implemented as 'XON/OFF' and the same setting should be made in the vi. You could measure temperature/voltage/current at the same time by doing this.

• Tecra M5 - SD card reader works with the factory settings

  Hi all
  My SD card reader has been in place. It will read a few cards of 4 GB and won't read other (usually newer).
  All cards in this problem area are Transcend cards 4GB SD (HC or whatever the format more later is)
  The cards, the M5 will not read can be read both my PDA, but also an old Tecra 9000 (who will also tell the other 4 GB cards)

  The PC was recently engineers have a problem so I asked to look at this problem. They reported that it was a software problem, because if they load the recovery CD (that is, to bring the machine to factory State) the SD card reader reads cards problem OK; Back to my setup and the SD card reader can not read cards SD - error message is "the request cannot be performed because of an i/o device error."

  So I guess that I need new drivers. Very well except that it has no drivers for the drive SD card itself. Its a part of the motherboard. There is a 'secure module SD' on the download from Toshiba site and I downloaded and installed the SD Secure module (dated 2008)
  However, Device Manager still shows that the SD host controller driver is Microsoft version 01/10/2002 6.0.4069.5

  If anyone has ideas on how to fix

  TFA
  R

  Hello!

  > back to my setup and the SD card reader will not read SD cards
  Can you explain what you mean, please?

  I put t understand why you n t run factory if it s a software problem. I never had problems with the factory settings because then I can make you that all functions work properly on my laptop.

  Good bye

• Performance of CVI 2013 SP2 with CVI 2015 - Windows XP problem

  I see that XP isn't an operating system in 2015 of the CVI.

  Most of our PC are Win7 now, but we have some legacy units which require XP due to a limitation of external controller processor.

  Is is possible to generate executables in 2015 CVI which will work correctly with the runtime of 2013?

  Alternatively, CVI SP2 from 2013 and 2015 CVI co-exist on the same PC development?

  I would not get stuck with CVI 2013 SP2 for the future just to maintain a few predictable XP-based PC.

  Hi Shr,

  I recommend reading through this community's message: https://decibel.ni.com/content/docs/DOC-23955

  Essentially, you can develop a code in CVI 2015 but set the executable to run on previous versions of the Run-Time Engine. Note that the older version of the RTE of Side-by-Side CVI is 2012. You can indeed install previous versions of the CVI on the same computer. The shared runtime will be set to the latest version. Other versions will be side-by-side. The code is not guaranteed to work with previous versions of the RTE so be sure to test the code locally before moving on to another computer.

• Reading data with NOR-5772

  I'm reading the data with the NOR-5772.  I tried the example code(NI_5772-Getting_Started_(Host).vi), and it will read noise (with nothing plugged into channels).   However when I try to send a signal (such as that generated with a NEITHER-DAQ card on the same system and routed to AI0/AI1), the signal does not change a lot of the noise.   I have the drivers updated and am under LabView 2012 (32-bit and 64-bit, I get the same result)

  Everyone has to experience this problem?   Thank you.

  Yes, the device is AC coupled and has a high pass filter.  There is a diagram of frequency response on page 20 of the user manual:

  http://www.NI.com/PDF/manuals/373625a.PDF

  It seems that the cuttoff frequency is about 100 kHz.

• Pavilion dv6 fingerprint reader has stopped working

  My fingerprint reader has stopped working. I can open the Simple pass identification program but when I click on fingerprints, it indicates 'identity check' with an hourglass on the top of the icon of fingerprints, and no matter how long I wait, that's all that happens. All advice appreciated.

  -----------------------------------------

  Pavilion dv6t laptop 3100, Win 7 Home Premium 64-bit, 8 GB of RAM, processor i5

  "Where you go, there you are."

  Hi Mikey,

  Looks like you're running the Digital Persona of SimplePass flavor.

  Two things to consider / try, in order.

  If the reset works, you don't have to reinstall the driver...

  • Hard reset
  • Reinstall the driver

  Hard Reset:

  Sometimes, all you need to do is the computer suddenly.  This method works for a variety of connection and "glued" program issues.

  • Disconnect all the external devices first.
  • Remove the AC power and battery
  • Press and hold the power button while in the minus 30 seconds
  • Reinstall the power supply for the first start only * see Note
  • Power on - connect
  • Next time you shut down the system, replace the battery.

  * Note: You can ignore the little battery aside.  If you wish, replace the battery the first time and do it with her.

  =====================================================================================

  The pilot, from your Internet site:

  Validity fingerprint sensor Driver sp52354 V2.1.0.2

  • Install the validity sensor Driver installation package: it if called sp*.exe - the package will be most likely located in the downloads folder.  If you have control of "Admin", you can highlight the package and "double-click on ' to install it, otherwise just right-click, select"Run as Administrator"and install.

  I hope this helps!

  It's my pleasure to help.

  Say "thank you!" to the help by clicking on the star of Kudos to show your appreciation.

  Fixed?  Mark this message 'accept as Solution' to help others find the answers.

  Note: You can find "Accept as Solution" only on the threads started by you.

  Good luck!  Year of the Dragon!

• DAQmx task Read DAQmx with sampling frequency of 10 Hz produced much too much data

  I have a simple configuration with a strain of channel 4 OR-9237 amp holds a carrier of series C of WLS - 9163 (wired ethernet mode) - Details probably does not matter.

  I used MAX to create a DAQmx task associated with which all four gauges samples.  The calendar setting is "Scan Loads" is continuous sampling, 2 k buffer (read samples) and 10 Hz rate.  I guess that this task would generate 40 data values per second - 10 for each channel.

  I have a simple loop of reading using DAQmx Read.vi that works always (without any stimulation time).  Playback is set to read all available data and then pump it into a table.
  In the attached example, I also added a few words of debugging to stop the loop after N iterations.

  As the loop is programmed with a 0.2 second period, I expect each pass of the loop to read about 8 samples or 2 samples per sensor.  Instead, I get hundreds each passage.  It's like reading has substituted the sampling frequency specified in the task of the unit.  I absolutely need data to be material to the rhythm.

  Where have I lost?

  Thanks Adnan,

  I changed your example I selected 'Strain gage' entry analog and then lowered the minimum and maximum thresholds to +-1-2.  What happens is that each other in the loop, I 2048 samples or zero samples.  The display flashes a whole line and then it clears any other past.

  In response to your second post, I understand that the loop cannot run quite right that I select.  I think that, but at a sampling frequency of 10 Hz, I have to sleep on the software side for nearly a minute before I built 2 K samples.

  I played with the frequency of sampling, assigning to various values from 0.1 to 10000Hz.  The behavior is the same until I approach the high rates where available samples remains to 2048-4096 sometimes, the display becomes continuous.

  Ahhh, Darn.  Yet another search was this link that points to the root of my confusion.  The 9237 can taste arbitrary rates using its internal clock.  Duoh!  I wish that the pilots are smart enough to warn you if there is a discrepancy between the selected sampling rate and capabilities of the device

• Alignment of memory with CVI 2013 problem

  Hello

  I just installed 2013 CVI from CVI 2010 and opening my old projects, I'm in trouble with the alignment of the memory.

  Not in all the projects that I opened, I get the problem, and I'm quite confused about this.

  I used to keep in line with the limits of 1 byte of memory and I have thousands and thousands of saved file with this method.

  I have prepared a very simple project (attached to this post) to illustrate the problem, consider that the result would have been with CVI 2010 'occupation of 5 bytes.

  Pragma pack() change his behavior?

  Y at - it a flag set in the Options menu or elsewhere?

  If anyone has a suggestion please help me.

  Thank you

  Sergio

  Hello

  I found the problem, there's a semicolon that follows the directive of preprocessor #pragma pack (1), and it causes the pragma is ignored.

  Remove the semicolon, everything works fine.

  Sorry!

  Sergio

• Sapera LT used with CVI

  Is that what someone has successfully used vision of DALSA, Sapera LT, with CVI library?

  Sapera LT supposedly has a C language interface.

  I have this poster in the forum of machine vision, but he seems to be more a SW problem (if, indeed, there are problems) a matter of HW.

  In principle, any standard interface of C (C89) should work with CVI I think... If it's for a framegrabber DALSA, or anything else.

  I was just curious if anyone had tried this specific thing, and if so, how it worked.

  Thank you

  Menchar-

  It turns out that you can use Sapera LT with CVI 2009.  You use the api 'base' which is an interface in ANSI C with the export header file and import for the DLL library is involved.  During compilation, I found 6 #defines which were redefined to somehow - the limits they were constant max on the different types of integers.    It seemed the stuff of limits.h, but it wasn't - I never figure out how or where he defined twice, so I just #undef had these just before the place where was held the redefinition and the problem disappeared.

  I was unable to use the framegrabber as a "camera" (peripheral), I used as a 'framegrabber"and loaded separately from the configuration files CCA and .cvi instead of a camera (.ccf) configuration file.  I have hooked up to a simulator CameraLink and grabbed a focus, then he wrote on the disk.  A close inspection of the data showed that it was seizing everything is OK.

  I used the 1.5 LT Sapera 7.0.0 and X 64 driver version.

  So I feel pretty good about this so far.

  Menchar

• Executable built with CVI 8.1 error-5093, the analysis library is not found

  Upgraded to 8.1 Labwindows/CVI of Labwindows/CVI 7.0 development machines. An earlier application was built using the ICB 7.0 and installed on a test computer. The same code built with CVI 8.1 is any error during execution of the function stdev, 5093 error code has been generated. (From analysis.h: LibraryNotFoundAnlysErr =-5093, / / the analysis library was not found.) Tried to build a facility with 8.1 and installation on the test computer and application errors still executing the stdev function. Back to the same application, but built with CVI 7.0, it works fine. Am I missing something with the build in 8.1 options? Or is it something in the workspace or project? Please notify. Thanks in advance

  Hi Tommy,.

  In CVI 8.0, the implementation of the analysis library has changed a static library that is linked to your .exe in a DLL that must be loaded when running. If you rebuild your source code and you want to deploy to another machine where the CVI environment is not installed, then you must re-create an installer in CVI 8.1 distribution, so that he can pack the analysis as well as your program library.

  You can confirm whether the analysis library is installed by searching for C:\Program NIUninstaller Instruments\Shared\Analysis\nianlys.dll in your target machine (although it is not enough to simply copy this file manually).

  When you create an installer in the CVI, be sure that, in the tab drivers & components in the dialog box change Installer , support of analysis element under the Group of LabWindows/CVI Run-Time Engine is checked.

  Luis

• I get an error, 'Adobe reader has stopped working ".

  My computer is running Vista and a few days ago my Adobe Reader launch is no longer.  If I click on the drive icon or try to open a pdf file all I get is a message "Adobe Reader has stopped working".  On the other hand, the program works in safe mode.  I tried to uninstall/reinstall and even a restoration of the system among other things.  Met someone with something like that, and if so, what is the difficulty?  Thank you.

  Originalt title: Adobe Reader launch

  Hi Tblud

  Uninstall adobe reader software using the uninstall program.

  Download and install the lower version of the adobe reader software.

  Now, the problem will be solved.

  If you are prompted for updates... you can update.

  Thank you...

• PDF 10 Adobe Reader incompatible with Windows 7

  # 1 cannot open attachments in PDF I get. 10 Adobe reader may not decode properly PDF any file I receive.  Has opened a small window box of jibberish.  I tried to use ALL the decoding options... nothing can open the PDF doc...

  # 2 cannot create any WORD document to PDF format.

  #3 now... situation is so bad... when I open Aodobe Reader 10... the screen goes to about only 200% size Misty color window Adobe which is totally unusable.

  I have gone wrong and I get a message back: "detected incompatible version.

  With my old VISTA ops system... PDF reading and creation of PDF has been instantly successful

  I tried in vain to find how to install an earlier version of the software ADOBE reader... like 9 or 8?

  Thank you!!!

  The f

  Adobe Reader has always been problematic. I have it dumped for this lightweight and user-friendly Windows player. I suggest you give it a try.

  Foxit Reader
  http://www.foxitsoftware.com/Secure_PDF_Reader/

• read swf with ipad

  French:

  Hello

  I created a file with animations "buttons" (inDesign plugin) that simply meets a page redirect (so I can use the hyperlinks) but also an animation at the "arrival and many"pop up"on the page (buttons)."

  So, when I it lorsque je l' exporte exported in swf (flash) it is not read on my iPad but it works on computer, rendering isn't exactly what need me. At least, everything works. When I export it en interactive pdf necessarily animations do not pass. Epub/HTML5 rendering is completely decomposed...

  Conclusion I thought I could export it in the form of folio, to put it online and have animations. Is this the right solution but how to do?

  I tried to read it with "Adobe Content Viewer" but I can't even get it back on my tablet...

  What is the process from export (in which format?), until power read on ipad? Thanks in advance...

  English:

  First avable, sorry for my English, I'm a french student bad!

  I created a pop-up with the plugin for Indesign book (buttons: page redirection, 'pop up effect' display/hide..)

  When I export in swf (flash) my ipad can not read my book, but it works perfectly on my computer! (Normal, because the iPad do not read flash).

  With 'interactive pdf', animations do not work, and epub or html my book is broken...

  So finally, I thought, as a "folio has" put the book online and have animations working export... Do you think it is good idea? And how?

  I tried to read the book with the application "Adobe Content viewer" but I can't put it on the Ipad...

  Can someone explain to me, in format of wich I want to export, and what the process is to read the file on my iPad?

  Thanks in advance!

  https://helpx.Adobe.com/InDesign/using/publish-online.html

• Adobe Reader has not been installed successfully on Mac

  Computer:

  Mac Mini 3,1

  2.26 GHz

  4 GB OF RAM

  Mac OS 10.11.4 (latest version of El Capitan)

  Using the installer on the Adobe site seems to be working, but then the Web page loads with the error message "Adobe Reader has not been installed successfully". I tried this three times.

  I tried to use the stand-alone Installer, twice. It hangs at "Running scripts package", telling about a minute ago left. I left it like that for hours before having to make a hard stop.

  No folder/Adobe applications have appeared in the Applications folder.

  I rebooted several times and the disk permissions fix, but the problem remains the same.

  Hello

  It seems to be the issue of authorization to file & folder in Mac, please refer to this link for help permissions & Disk Space | Apple Support communities.

  Once you have the right to install the software, please download Adobe Reader using this link Adobe Acrobat Reader DC install for all versions

  If the problem persists, then would you please check with the account of another user with Admin rights to reproduce the problem.

  Kind regards

  Christian

• Adobe reader has disappeared after installing the update or unable to re - install, already says "the application installed.

  Adobe reader has disappeared after installing the update or unable to re - install, already says "the application installed.

  The adobe reader program no longer exist in my C drive.

  I use windows 8 and tried reinstalling countless times, disable the anti-virus, restarted my computer, etc.. Have also tried uninstall adobe, but the program does not exist more...

  Please help because my exams are in 5 days and all my study material must be opened with pdf!

  Thanks in advance.

  Hi, Fabien,

  Is - this directory exists on your system? -C:\Program Files (x 86) \Adobe If Yes, do you think that Adobe Reader folder in there?

  Please use the tool on your system: http://labs.adobe.com/downloads/acrobatcleaner.html

  Reinstall Acrobat Reader DC on your system? Adobe - Adobe Acrobat Reader DC Distribution

  Kind regards
  Rahul Tyagi