All virtual machines down due to problem of firmware - update firmware HBA

Similar Questions

• All virtual machines on my ESX host off power at the same time

  Hi all

  Recently I attend the interview. a guy asked me this question

  < police = "Times New Roman, serif" >all virtual machines on my power off ESX at the same time host < / police >< / police >?

  What was the cause of the highest of the error, how to troubleshoot the error.please me.anybody guide to address this problem?

  Thanks

  Surya

  If all the virtual machines if lower at the same time, my bet would be VMware HA. Just for fun, build it inside your head:

  (1) 8 ESX nodes, all service consoles connected to a unique management switch.

  (2) now to create a cluster of these nodes, put all your virtual machines in there and activate HA, choose ' host isolation response: power off.

  (3) draw power from your management switch. HA on each host will deduct that the host is isolated-> turn off all the virtual machines.

  Each host will think the same thing, and hop find you with all virtual machines down to the time in the whole of the cluster. Have seen this one several times when people go and upgrade their management switches in the evening ("hey, it's only management").

  Visit my blog at http://www.vmdamentals.com

• Close all virtual machines on ESXi

  Hello

  I'm new in the administration of vSphere. I would like to raise our ESXi servers due to updates, but I've read that you shut down all virtual machines that are on it. You have something better to do then close VMs one? I expect a powershell script, but I have found none so far.

  Thank you

  Kralijir, you can do it from the console GUI.

  In the left pane, select the ESX host.

  In the right pane, click the tab "virtual machines". Now, you can select block all virtual machines here and simply right-clicking them stop all, or make other changes in bulk.

  Some changes via selection bulk require all virtual machines to be in the same State; Turned off the power, power, etc.

  If it works for you, please mark this answer as the 'response '.

• ESXi 4.1 upgrade to ESXi 5.5 while all virtual machines and data warehouses

  We have two servers ESXi 4.1.0 348481 (Essentials) and we need to upgrade to ESXi 5.5 for support of Windows Server R2 2012. We intend to use the interactive upgrade. We want to ensure that the virtual machine is preserved. More precisely VMFarm001 where ESXi is installed in the same data store as VMServer1. VMServer1 is our largest server and cannot be migrated to another data store easily because we are not allowed for vMotion.

  The following layout

  VMFarm001

  Dell PowerEdge R710

  Data store:

  Storage1 - 1.36 TB

  VMServer1 - MS Server 2003

  Install ESXi

  Storage2 - 1.82 TB

  VMServer2 - MS Server 2008 R2

  VMServer3 - MS Server 2008 R2

  VMFarm002

  HP ProLiant ML350 G5

  Data store:

  Storage1 - 95GB

  Install ESXi

  ISOs

  Storage2 - 1.82 TB

  VMServer4 - MS Server 2008 R2

  VMServer5 - MS Server 2008 R2

  I have a feeling I'm worried for nothing given that option during the ESXi upgrade and keep the VMFS datastore.

  Thank you

  Yes, that's correct.

  I recently finished the upgrade of lots of stand-alone hosts ESXi 4.1 (with local storage only) to 5.1 and all were successful. The same process applies to 5.5, so you shouldn't have a problem with preservation of VMFS data warehouses (and all virtual machines).

• Gwetting a list of all virtual machines and used space

  
  I apologize for my very basic question.

  I need to make a file (better if an Excel file) with a list of all virtual machines in a simple 5.x vSphere infrastructure including 2 VMare ESXi 5.x servers and the disk space used (allocated, used) of each virtual computer.

  The easiest way seems to list the virtual machines from the vSphere client and export the list as a .xls file.

  It seems simple, but when I look at the file I see a lot of missing VMs or a large number of missing values for several virtual machines (just the Runts).

  Is this a problem with my vSphere client?

  I tried to create a PowerCli script using the "Get - VM|" Select-object Name"command, but my limited skills will let me extract the value of the used space.»

  Can someone please provide a sample of PowerCli I can just copy and use?

  Is there another way to get the information I need?

  Concerning

  Marius

  .

  Not knowing that if you have configured a cluster or just stand-alone hosts, here is one simple line...

  Get-VMHost-name | get - vm | select name, usedspaceGB

  From there, you can make formatting, get total usage etc.

• Access to the network in all virtual machines lost after that put 8.1 to level.

  Today, I upgraded my host computer to Windows 64-bit Pro 8.1. I did the upgrade through the Windows store. There are no errors or problems during the upgrade.

  However: The host machine equipped with a Qualcomm E2200 network adapter, and it runs the 'Killer' Network Manager software called at startup. After the 8.1 update, when the machine did its last restart, Qualcomm Network Manager opened with a message that the LSP has not mapped correctly. I clicked 'YES' to remap it. Probably a stupid move on my part.

  Thereafter, I lost all network connectivity in all my virtual machines. I have virtual machines for Windows 8, Windows 8.1 RTM (not the preview) and Ubuntu 12.04 LTS. ALL of them have lost the network.

  The host computer has no network problem and works well after the upgrade.

  Any ideas or suggestions to reset network connections in virtual machines?

  All virtual machines are set to use NAT.

  Oh I have to say also that the host computer is running VMware Workstation 10 and everything was fine and dandy, has never had problems at all until this upgrade/LSP remap thing. I have install VMware Tools in the VM of Windows 8.1, with no effect at all.

  Thank you.

  -J

  Two things, I'll try:

  1. go in the virtual network editor and restore settings. The culprit is probably the VMNet to NAT configuration.

  2. If this does not work, it seems that the virtual card for NAT does not somehow. The simplest workaround is to uninstall and reinstall the workstation.

• Is no vmdk file, but the script says, all virtual machines backed up Ok!

  Hello everyone;

  Please excuse any lack of details because this is the first time that I write. I've scoured internet for days now trying to find no matter how much detail that could help me solve the problem. I'm new in the world of script ESXi and ghettoVCB.

  My intention is to run several tasks on a schedule. Each type of backup (quarterly, monthly, weekly, daily and multiple) runs at a specific time. The planning section works very well.

  I'm hoping to solve this urgent backup, I should be able to solve reboot.

  Here is the command I use:

  /vmfs/volumes/datastore1/ghettoVCB.sh w /tmp/ghettoVCB-work.multiple f/vmfs/volumes/datastore1/vmlist-Multiple g/vmfs/volumes/datastore1/vmconfig-DataSet1-multiple-l /vmfs/volumes/datastore1/ghettoVCB_logs/ghettoVCB.Multiple_Backup.log

  vmconfig-DataSet1-multiple contains:

  # Multiple backups - rotation County 6

  #

  VM_BACKUP_VOLUME = / vmfs/volumes/Vault2-DataSet1/URANUS/Multiple

  DISK_BACKUP_FORMAT = thin

  VM_BACKUP_ROTATION_COUNT = 6

  POWER_VM_DOWN_BEFORE_BACKUP = 0

  ENABLE_HARD_POWER_OFF = 0

  ITER_TO_WAIT_SHUTDOWN = 4

  POWER_DOWN_TIMEOUT = 5

  SNAPSHOT_TIMEOUT = 15

  ENABLE_COMPRESSION = 0

  VM_SNAPSHOT_MEMORY = 0

  VM_SNAPSHOT_QUIESCE = 0

  VMDK_FILES_TO_BACKUP =

  Vmlist-multiple contains 1 server is listed:

  # List all virtual machines that are backed up several times a day

  HEAT

  The log indicates that the backup was successful - but it has not been the case. Backup size should be approximately 8 GB. However, when you look at the output folder, only the following files are here:

  
  

  HEAT.vmx

  STATUS.ok

  Question is now - where are the vmdk files that should be present?

  Output (-d debug) can be found here: http://pastebin.com/hMGphTL3

  So, here is what I observed:

  When you run the script, the snapshot only takes a few seconds to create and delete then. I'm seeing happens on the list of the tasks of vSphere Rencent (screenshot attached).

  If I create a snapshot manually - it will take much more time to create and delete a snapshot. The difference here is 6 minutes, and 4 seconds using the script create a snapshot manually.

  So my presumption is that he is not actually create the snapshot, although vSphere said it is being created. So why is it the case?

  Help, please.

  ADDENDUM:

  If I run the following:

  ./ghettoVCB.sh m HEAT

  The backup is successful.

  Your said he clearly did not config file to back up all files hard.

  VMDK_FILES_TO_BACKUP =

  I expect to see something like this if you want all the hard files

  VMDK_FILES_TO_BACKUP = "all".

• Get-file provides an account of all virtual machines in the folder structure.

  Hi all

  Tried a few searches in the community, but impossible to find exactly what I was looking for.  We have a configuration folder structure in vCenter.  We have some companies that we bought over time and we set up a folder, separate them with a top-level folder and folders nested for different types of virtual machine below, something like:

  CompanyX

  -Mail servers

  -Web servers

  -DB servers

  For the purposes of internal billing, asked me to get a count of all virtual machines for each company.  I can get the count for virtual machines directly in the "CompanyX" folder, but it does not include virtual machines in subfolders.  This is the script I used so far:

  Write-Output "VM enumeration for CompanyX VMware environment Total: $((Get-dossier 'CompanyX' |)). "(Get-VM) .count) | out-file "D:\ScriptResults\CompanyX.txt" - append

  As I said, that works very well for the virtual machines in the head in the parent folder, but it does not go down to the next layer.  Is there a way to get folder do that?

  I am a novice PowerShell/PowerCLI, so forgive me if I'm missing something obvious.

  Thank you

  Bob

  Hi Bob,

  I don't know if it was different in previous versions, but in the latest PowerCLI version 4.1 U1 if you

  Get-file "CompanyX" | Get - VM

  It will retrieve the VM in the top folder and all subfolders. You can easily check this with:

  Get-file "CompanyX" | Get - VM | Select-Object - Property Name, folder

  If you only want the virtual machine in the top folder you can use:

  Get-file "CompanyX" - NoRecursion. Get - VM

  The following script will get the VM number for all companies and write the result to a .csv file.

  $ExcludeFolders = "Discovered virtual machine","other folder to exclude"
  Get-Folder vm | Get-Folder -NoRecursion | `
  Where-Object {$ExcludeFolders -notcontains $_.Name } | `
  ForEach-Object {
    $Folder = $_
    $Report = "" | Select-Object -Property Company,"Number of VM's"
    $Report.Company = $Folder.Name
    $Report."Number of VM's" = ($Folder | Get-VM | Measure-Object).Count
    $Report
  } | Export-Csv -Path CompanyVMsCount.csv -NoTypeInformation -UseCulture 
  

  If there is high records of the page you want to exclude from the list you can add them to the $ExcludeFolders variable in the first line of the script. The second line of the script gets all the 'vm' top of the folders page. The third line filter unwanted records. A few lines create the output objects. And the last line written objects in a .csv file.

  I added the Measure-Object cmdlet for the ($Folder |) Get - VM | Measure - Object). Account because otherwise you will get an error if the number is 0 or 1.

  Best regards, Robert

• Start all virtual machines

  Hello

  A couple of weeks, I installed Vmware server 2.0 on Ubuntu 8.04 server, I must say that it works perfectly, I encounter any problem yet. At this point, I am trying to automate some processes such as backup and start and stop virtual machines.

  The thing is for the moment we have 4 virtual machines and im starting those manually now (1 by 1) using the vmrun command, now my question is, is anyway to start all virtual machines at the same time? I tried many things and I can't make it work, some help would be really appreciated.

  Thanks in advance and best wishes,

  Stone.

  OK - enter you requirement exactly, in my defense.

  I posted earlier, a shell script to the server 2.0 beta forum, which found all the *.vmx scripts, and then made a "suspend" their needs so very easy to change it to do a 'departure' instead.

  See the 'vmware - suspend' script in this post:

  http://communities.VMware.com/message/1036371

  Post edited by: guyrleech

• vCenter shows all virtual machines and the host is disconnected

  Hello

  I have a two nodes in the cluster ESXi6 U2 (recently updated to 5.5) running on hp dl380p gen8. For some reason all the virtual machines are running on host A (HA and DRS are enabled).  vCenter shows all virtual machines and host A is disconnected. Cannot connect to A host using vSphere client or web client. Cannot vMotion the VMs. Impossible to activate SSH. Connection DCUI works very well. Cannot perform any action VM

  All virtual machines are in place are running at this point. I don't want to restart the virtual machines. Can you help me please?

  Thank you

  AJ

  Frozen screen DCUI came back to life. The active SSH access, killed the running process. The host of running backs.

  See you soon,.

  AJ

• I'm looking for a Script that can list all virtual machines with type of NIC E1000 via the output of the CSV file.

  Hi gurrus and LucD

  I'm looking for a Script that can list all virtual machines with type of NIC E1000 via the output of the CSV file.

  The script should search for information in a multiple Vcenter servers and multiple clusters and list all the VMs name, status (two powers on or off) with type card NETWORK Type E1000 only no other.

  Concerning

  Nauman

  Try like this

  $report = @)

  {foreach ($cluster Get-cluster)

  foreach ($rp in Get-ResourcePool-location $cluster) {}

  foreach ($vm in (Get-VM-location the $rp |)) Where {Get-NetworkAdapter - VM $_______ | where {$_.}} Type - eq "e1000"}})) {}

  $report += $vm. Select @{N = "VM"; E={$_. Name}},

  @{N = 'vCenter'; E={$_. Uid.Split('@') [1]. "Split(':') [0]}},"

  @{N = "Cluster"; E = {$cluster. Name}},

  @{N = "ResourcePool"; E = {$rp. Name}}

  }

  }

  }

  $report | Export Csv C:\temp\report.csv - NoTypeInformation - UseCulture

• All virtual machines to an ESXi Server ping

  Hi all

  For a project of mine, I need to create a script that asks for the ESXi server host name,

  and after that start ping all virtual machines that are on the ESXi server.

  I tried to do without success up to now.

  Help will be appreciated.

  Thank you!

  What follows is based on the fact that the VMware tools are installed.

  If they are not installed, you could adapt the script to try and ping displayname VM.

  $esxName = "MyEsx".

  Get-VMHost-name $esxName | Get - VM | %{

  $hostnamePresent = $_. Guest.HostName - don't $null

  {if ($hostnamePresent)}

  $pingable = test-Connection - ComputerName $_. Guest.HostName - count 1 - calm

  }

  else {}

  $pingable = $false

  }

  Select - InputObject $_ - the property name.

  @{N = "This Hostname"; E = {$hostnamePresent}},

  @{N = "responding"; E = {$pingable}}

  }

• Database SQL query to get all virtual machines with comments enabled customization?

  Hello

  Does anyone know of a SQL query that can be executed against the vCloud Director DB for all virtual machines who invited enabled customization?

  I can't have PowerShell to pull these data on a global scale.

  Thank you

  jkasal

  Has taken a quick...

  Select top 10 v.id, v.name, v.vapp_name, v.vc_id, v.moref, ui_vapp_vm_list_view v.guest_customize_enabled v with (NOLOCK)

  seems to have if the setting is enabled or not.

• The list of all virtual machines with more than 2 virtual disks

  Hello.

  I want to list all virtual machines in a data center vCenter, who got more than 2 virtual disks. Here's the workflow, I am working on that:

  1 get the view of data center

  2. get the Cluster Data Center view like the 'begine_entity '.

  3. for each view cluster overview the VirtualMachine bit cluster seen as 'begin_entity '.

  4. for each VM view, this information: VirtualMachine-> config-> hardware-> device of

  Above information is a table.

  I need help in order to extract information from this table disk, then run an if condition where the VM who got more than 2 discs should print.

  Could help you. I wrote the script to the point 4. just need advice for the posterior.

  Thank you.

  You can try one of the following values-

  1 If ($vm-> {'summary.config.numVirtualDisks'} > 2) {...}

  2 $diskCnt = grep {$_-> isa ('VirtualDisk')} @{$vm-> {'config.hardware.device'}};

  The above assumes that you've got your $vm with a filter property as follows:

  $vms = Vim::find_entity_views (view_type-online 'VirtualMachine'), the properties-online ['summary.config.numVirtualDisks', 'name', 'config.hardware.device'];

  my $vm foreach (@{$vms}) {}

  ...

  }

• All virtual machines with VLAN

  I'm trying to get a list of all virtual machines in a given VCenter, with their VIRTUAL networks. Can anyone help?

  If your virtual machines are connected to dvSwitches instead of ordinary vSwitches?