Allowing the VPN and return to the ASA 5520

Similar Questions

• Cisco Anyconnect VPN and IPSEC coexist on ASA 5520?

  Can a Cisco ASA 5520 which has been configured as IPSEC VPN gateway and also be configured as a gateway ANYCONNECT VPN and vpn IPSEC service anyconnect vpn clients clients maintenance at the same time? Any negative impact on the performance or any other problem that everyone knows?

  I guess that by 2 connection limit, you are referring to the 2 licenses for anyconnect?  You should consider using the anyconnect essentials license, which is relatively cheap (100-200 dollars I think) and will take you to the edge of the platform with anyocnnect.

  You shouldn't have any problem using IPSEC with LDAP client.  It is quite common - my company is IPSEC as Anyconnect off the coast of the same interface using authentication ldap (even same-group policy) for the two.

  -Jason

• VPN site to Site with ASA 5520 * please help *.

  I am using two ASA 5520, and try to put up a site to site VPN.  This seems to be pretty simple, but I'm on my third day of train this is up and running. Both 5520's are running the latest 9.1 (5) IOS.

  Please note: I replaced it with [#1-WAN IP] and [#2-WAN IP] for WAN IP of the ASA addresses.

  Thanks in advance for any help you may have.

  -------------------------------------------------------------------------------------------------------------------------------------------------

  ASA 5520 # 1:

  Crypto ikev1 allow outside

  the local object of net network
  10.0.0.0 subnet 255.255.255.0

  net remote object network
  172.20.0.0 subnet 255.255.255.0

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group [IP #2-WAN] type ipsec-l2l

  IPSec-attributes tunnel-group [#2-WAN IP]
  pre-shared-key cisco123

  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  card crypto oustide_map 1 match address outside_1_cryptomap
  card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
  card crypto outside_map 1 set pfs Group1
  map 1 set outside_map crypto peer [#2-WAN IP]
  outside_map interface card crypto outside

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  -------------------------------------------------------------------------------------------------------------------------------------------------

  ASA 5520 #2:

  Crypto ikev1 allow outside

  the local object of net network
  172.20.0.0 subnet 255.255.255.0

  net remote object network
  10.0.0.0 subnet 255.255.255.0

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group [#1-WAN IP] type ipsec-l2l

  IPSec-attributes tunnel-group [#1-WAN IP]
  pre-shared-key cisco123

  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  card crypto oustide_map 1 match address outside_1_cryptomap
  card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
  card crypto outside_map 1 set pfs Group1
  map 1 set outside_map crypto peer [#1-WAN IP]
  outside_map interface card crypto outside

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  Try to correct the mistakes in the two configs.

  In some places, you have 'oustide_map' where you need "outside_map".

• Failover of VPN for data/VoIP through ASA 5520 or 7204 VXR

  I would like to install a VPN failover for my remote sites using broadband 3dn/1up.  They are mainly 2800 routers.    I like options for end hub a pair of Cisco ASA active / standby and a 7204 VXR.  Voice and data will travel down the VPN failover and I intend to have QOS/Traffic shaping in place to better meet the needs for VoIP as possible.  I need to do it on about 150 sites. My questions are:

  1. What is the best why the ASA or the 7204

  2 Will VoIP packets pass through the two in the same way

  3 as far as redistributing routes can I use GRE on an ASA or should I keep all static. NH on the SAA is an L3 switch.

  4. an ASA with 100 mg of bandwithd through metro E supports 150 tunnels making VoIP and data. 1 to 3 calls per site max.

  Thank you

  J R

  To answer your questions: -.

  1. who is better for this, the ASA or the 7204 - ASA, is what is designed to do.

  2 packages VoIP Will cross both the same way - Yes

  3 as far as redistributing routes can I use GRE on an ASA or should I keep all static. NH on the SAA is an L3 switch. -l'ASA does not support GRE tunnels.

  4. an ASA with 100 mg of bandwithd through metro E supports 150 tunnels making VoIP and data. 1 to 3 calls per site max. -It depends on the model of the SAA, see the below matrix for thru-put http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html

  HTH >

• VPN l2l failed inside on ASA 5520 (8.02)

  VPN l2l is dropping packets to Phase 5 because of a rule configured. I have an isakmp his but the client cannot connect to the destination here in my network. I'll post my config to access list at the bottom of the Packet-trace output.

  vpnASA01 # entry packet - trace within the icmp [10.0.0.243] 0 8 10.97.29.73 det

  Phase: 1

  Type: CAPTURE

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xc92087c8, priority = 12, area = capture, deny = false

  hits = 85188209121, user_data = 0xc916a478, cs_id = 0 x 0, l3_type = 0 x 0

  Mac SRC = 0000.0000.0000, mask is 0000.0000.0000

  DST = 0000.0000.0000 Mac, mask is 0000.0000.0000

  Phase: 2

  Type: ACCESS-LIST

  Subtype:

  Result: ALLOW

  Config:

  Implicit rule

  Additional information:

  Direct flow from returns search rule:

  ID = 0xc87f1f98, priority = 1, domain = allowed, deny = false

  hits = 85193048387, user_data = 0 x 0, cs_id = 0 x 0, l3_type = 0 x 8

  Mac SRC = 0000.0000.0000, mask is 0000.0000.0000

  DST = 0000.0000.0000 Mac, mask is 0000.0000.0000

  Phase: 3

  Type: FLOW-SEARCH

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Not found no corresponding stream, creating a new stream

  Phase: 4

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 10.0.0.0 255.0.0.0 inside

  Phase: 5

  Type: ACCESS-LIST

  Subtype:

  Result: DECLINE

  Config:

  Implicit rule

  Additional information:

  Direct flow from returns search rule:

  ID = 0xc87f3670, priority = 111, domain = allowed, deny = true

  hits = 67416, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 4000, protocol = 0

  SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  DST ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  the output interface: inside

  the status of the output: to the top

  output-line-status: to the top

  Action: drop

  Drop-reason: flow (acl-drop) is denied by the configured rule

  = ACCESS-LIST + Config =.

  the object-group L2LVPN-blah_local network
  network-object 10.97.29.73 255.255.255.255
  the object-group L2LVPN-blah_remote network
  network-object [10.0.0.240] 255.255.255.240

  INBOUND_OUTSIDE list of allowed ip extended access object-L2LVPN-blah_remote L2LVPN-blah_local group object

  L2LVPN-blah_obj allowed extended ip access-list object-L2LVPN-blah_local group L2LVPN-blah_remote

  access-list SHEEP extended permits all ip [10.0.0.243] 255.255.255.240

  Route outside [10.0.0.240] [10.97.29.1] 255.255.255.240 1

  address for correspondence card crypto outside-VPN 46 L2LVPN - blah_obj
  peer set card crypto VPN-exterior 46 [10.0.0.243]
  outside-VPN 46 transform-set esp-sha-aes-256 crypto card
  outside-VPN interface card crypto outside

  IPSec-l2l type tunnel-group [10.0.0.243]
  IPSec-attributes of tunnel-group [10.0.0.243]
  pre-shared-key *.

  [10.0.0.1] is to protect the global addresses of clients. Assume that these are still used in place of the current range of intellectual property. 10.0.0.240/28

  ===========================================

  Thanks in advance.

  Michael Garcia

  Profit Systems, Inc..

  Hi Michael,

  -Is the IP peer really part of the network that make up the field of encryption?

  -Is the ACL INBOUND_OUTSIDE applied (incoming) inside or outside interface (inbound)? It is the current form, it would need to be on the external interface.

  -You specify the peer IP only in the ACL SHEEP, so all other traffic is NAT would and eventually denied because it does not match the field of encryption

  Someone else may have a few ideas, but these are questions I have for the moment.

  James

• Information on the ASA 55xx

  Hello

  I'm starting to read about ASA 55xx in Cisco's Web site. But after a good read, I have a few questions...

  1. In Cisco Docs on ASA55xx, I see the "Maximum simultaneous AnyConnect or VPN sessions without client" and "Maximum simultaneous site-to-site and VPN IPsec IKEv1 sessions" (e.g. 750 times): well, the concurrent sessions maximux are 750 + 750 (anyconnect + site to site), so I have to add both types of sessions? Or what are the maximum (of each type) concurrent sessions in ASA5520?
  2. So, at this point, if I want 750 AnyConnect Session and site to site 750 Session what license should I buy? ASA5500-SSL-750? ASA-VPN-1000? or whatelse?
  3. so, what are the license "shared"? Where and when do I need to buy?

  Thanks in advance.

  Good bye

  The platform and required capabilities are allowed as indicated in the data sheet of the product:

  Up to 750 AnyConnect and/or peer clientless VPN can be supported by each Cisco ASA 5520 by installing an essential element or a Premium AnyConnect VPN license; 750 VPN IPsec peers are supported on the base platform. Resilience and capacity VPN can be increased by taking advantage of the Cisco ASA 5520 clustering integrated VPN and load balancing features. The Cisco ASA 5520 supports up to 10 devices in a cluster, offering a maximum of 7500 AnyConnect and/or VPN without client peers or 7500 counterparts of IPsec VPN by cluster.

  Resuming:

  The ASA 5520 750 capacity VPN site-to-site is in the base license / product (part number ASA5520-BUN-K9 or ASA5520-K8 whther in function, you are eleigible to buy encryption strong (-BUN - K9) version)

  The user AnyConnect required licenses depending on if you need Anyconnect Essentials or Premium. The Anyconnect data sheet describes the differences. Essentials is a license that allows customers to use the device at the same time up to 750. Premium (which cannot be loaded at the same time as Essentials) requires that the licenses to buy according to the prioritized by the user schema.

  Shared licenses are shared between ASAs in a cluster (2 or more units configured together).

  There is the concept of licenses in a failover cluster (2 units). It's automatic - i.e. the license numbers are additive and shared up to the capacity of the platform. ASA5500-SSL-750 part would be used in this configuration.

  There is also the concept of a Premium Shared Server anyconnect. In this system, the shared server allocates licenses in 50 blocks of unity to the ars of cluster members they need. ASA-VPN-1000 part number you mention is used in this kind of configuration.

• Newspapers of the ASA

  I try to display the traffic logs. Can someone help me with the command?

  Here are the steps to install syslog server.

  First of all, you need to install syslog on a computer server software. You can

  Download one of the popular kiwisyslog Server

  http://www.kiwisyslog.com/software_downloads.htm . He is listed as Kiwi

  Syslog Daemon and the latest version is 8.2.8. You can download the standard edition, which works as

  a program.

  Once the syslog server is installed, then you should connect to the ASA in

  the terminal configuration mode and enter the following commands.

  Logging host [in_if_name] ip_address

  (example: host inside 1.2.3.4 record)

  We assume syslog server is installed on the computer with 1.2.3.4 IP address in the

  inside the network.)

  timestamp of the record

  exploitation forest siphon 4

  opening of session

  These commands allow the ASA begin sending messages syslog on the syslog server.

  For more information about the logging commands, you can see at this URL:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_command_refer

  ence_chapter09186a008010578b.html #1028090

  ----------------------------------------------------------------------------------

  Levels of trap

  . 0-emergency-system unusable messages

  . 1-alerts-take immediate action

  2 State - criticism-criticism

  . 3 errors error message

  . 4 warnings-Warning message

  . 5 notifications-Normal but significant condition

  message information. 6-Information

  . 7-debug-Debug messages and orders of FTP and WWW URL log

  Note the useful messages.

  Kind regards

  Sushil

• IPSec VPN to asa 5520

  Hello

  First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

  The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

  I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

  I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

  4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

  5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

  6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

  and this, in the journal of customer:

  Cisco Systems VPN Client Version 5.0.02.0090

  Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.1.2600 Service Pack 3

  24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

  Establish a secure connection

  26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "213.94.x.x".

  27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with 213.94.x.x.

  28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

  29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

  IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

  Set indicator established tunnel to register to 0.

  42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

  Can you see what I'm doing wrong?

  Thank you

  Sam

  Pls add the following policy:

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  You can also run debug on the ASA:

  debugging cry isa

  debugging ipsec cry

  and retrieve debug output after trying to connect.

• ASA 5520 - SSL VPN (Anyconnect) licenses

  Hello

  Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license?  Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium.  Our current license looks like this:

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5520 VPN Plus license.

  I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.

  I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect.  The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?

  Thank you

  Rob

  Hello

  The essentials license is per device and does not allow full-tunnel.

  If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/data_sheet_c78-527494_ps10884_Products_Data_Sheet.html

  Federico.

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• ASA 5520 IPSec NAT question

  I like more than 150 of VPN on my ASA 5520.  A specific customer, with that I'll put up a VPN has an overlap of two of the intellectual property, it must reach from its internal network.  It is NATing 10.251.11.177 internal network traffic to my ASA presents itself as 10.251.11.177 of the 10.251.11.176/29 network.  Now the two IP of its internal network, it must reach are 10.1.254.200 and 10.1.254.201.

  Thus, following the documentation on the site Web of Cisco I'm doing Policy Based Routing on the ASA 5520 (my thesis) so that its traffic will 1.1.1.1 and 1.1.1.2 instead of 10.1.254.200 and 10.1.254.201.  Once it reaches my ASA 5520 it gets back to these IP tranlated.

  I am using the following configuration, but when I try to add static entries, it won't let me add them.  I even tried "static 1.1.1.1 (exterior, Interior) POLICYNAT of the access list" with the ACL in reverse but no use.

  object-group, network VPN-map

  network-object host 1.1.1.1

  network-object host 1.1.1.2

  !

  POLICYNAT list extended access allowed host ip 10.1.254.200 10.251.11.176 255.255.255.248

  POLICYNAT list extended access allowed host ip 10.1.254.201 10.251.11.176 255.255.255.248

  !

  static (inside, outside) 1.1.1.1 access-list POLICYNAT

  public static (inside, outside) 1.1.1.2 - POLICYNAT access list

  Try breaking the IPs in two ACL

  POLICYNAT1 list extended access allowed host ip 10.1.254.200 10.251.11.176 255.255.255.248

  POLICYNAT2 list extended access allowed host ip 10.1.254.201 10.251.11.176 255.255.255.248

  !

  static (inside, outside) 1.1.1.1 access-list POLICYNAT1

  public static (inside, outside) 1.1.1.2 - POLICYNAT2 access list

  HTH

  GE

• Addition of Compact Flash in a Cisco ASA 5520

  I'm trying to install a 512 MB COmpact Flash for an ASA 5520 Cisco.  We inserted the compact flash, but when we do a DIR, it does not show.  even as an unformatted device.

  What should we do to make this a usable CF?  I just need to recharge the ASA or do I need to format the CF.  It was inserted into the slot in the back of the ASA 5520, and we ensured that had been properly rests.

  Thank you

  Dwane

  The Cisco FAQ article:

  I can hot flash player? For example, is it possible to change the flash player when Cisco ASA is turned on and running?

  It is always recommended that you turn off the Cisco ASA, while you insert the flash drive. This disables all working processes and allows the ASA to recognize the flash from the startup process.

• Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500.

  We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups.  It works, but it works too well.

  We have a group called XXX we need to have access to the Cisco AnyConnect Client.  We have selected this group of our Active Directory and added to our ACS configuration.  We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN.

  We added XXX movies for the elements of the policy of access to the network-> authorization profiles.  We also have a profile of YYY.

  She continues to knock on our default Service rule that says allow all.

  We have also created a default network access rule. for this.

  I am at a loss.  I'm sure I missed a checkbox or something.

  Any help would be really appreciated.

  Dwane

  We use Protocol Management GANYMEDE ASA and Ray for VPN access?

  For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too.

  On the SAA, you must configure Ganymede and Ray both as a server group.

  For the administration, you can set Ganymede as an external authentication under orders aaa Server

  AAA-server protocol Ganymede GANYMEDE +.

  Console HTTP authentication AAA GANYMEDE

  Console Telnet AAA authentication RADIUS LOCAL

  authentication AAA ssh console LOCAL GANYMEDE

  Console to enable AAA authentication RADIUS LOCAL

  For VPN, you must set the authentication radius under the tunnel-group.

  I hope this helps.

  Kind regards

  Jousset

  The rate of useful messages-

• VPN client and ssh to the external interface of the ASA

  Hello world

  I was testing clientless ssl in my lab at home.

  When you're connected via vpn without customer, I am able to ssh ASA outside interface, but when I use ssl vpn only I can't ssh to the external interface of the ASA.

  Need to figure out how I can ssh to the external interface of the ASA using clientless ssl vpn?

  Concerning

  MAhesh

  Mahesh,

  When you are on clientless SSL VPN to your customer is not limited routes of the Internet, isn't being NATted etc. If ASA is set to allow ssh from outside, then the VPN SSL without client user is no different from any other.

  A the user SSL VPN full tunnel can have any or all of these factors at play. One of them can cause the impossibility to access the ASA outside interface via ssh. I see the configuration to tell you which one (or more) is to blame.

• monitor the ASA remote site and allow the ACS to authenticate

  Hi all

  I have a VPN site to set up and works fine, but am struggling to get two things configured, hope can get help from you all

  I need to monitor the ASA distance of my HQ, I use kulvik with snmp, but I am afraid if he would be a threat if I open snmp on my external interface

  'access-list extended permitted snmp 20.x.x.x 19.x.x.x acl_outside' - is this safe

  my configuration:

  Remote

  10.8.0.0/20---ASA---Internet---ASA---10.0.0.0

  I was wondering is it otherwise I get my remote ASA monitored

  My next challenge is to add GANYMEDE ASA configuration, my CSA is 10.6.1.186 that can be reached from LAN(10.8.0.0/20) remote, but not the ASA because of politics, how can I get this to work

  I searched how to add the source interface in config GANYMEDE but couldn't get

  Thank you very much for the support

  See you soon...

  For the interface you want to use, can you pls add the following command:

  access to the administration

  For example:

  access to the administration server - vlan

  or

  access to data management - vlan

  You can only configure 1 interface for the management interface.