Am I banned or something?

Similar Questions

• Router/ISP/Internet problems! Help, please!

  Well, I tried to change my IP rogers for about a week because I got banned of something... I've heard of this thing called cloning MAC and wanted to try it. I've seen instructions on a Web site. He said that because I have my internet set up as "Modem Router to computer" I should go on my routers home page and change the settings from there. So after going on the site, I saw where it said "Clone MAC'. I got a MAC address, and then I took the card from my router and the Modem for 10 seconds and then plugged it in. There was something wrong! I couldn't use Firefox, Internet explorer and many more things internet related! I could always run liveupdate for my Norton 360, and I could always use Limewire. In addition, the average download speed was about 70 KB per second, when it is usually about 360 KB per second. Then, I connected the Modem directly to my computer without using the router and everything worked. A I mess up something with my router? Do you have my ISP Rogers, cut me? Please please help! I am running Windows Vista Home Premium 64-Bit. I have 4 GB of RAM. I have Internet Lite from Rogers.
  Thank you.

  Unplug your modem to your PC. Plug it back as before, modem to the Internet port on the router and then any port your pc LAN. Accessing the web interface and the mac clone, but he enter manually. When you click clone Mac. my PC it will copy the MAC address of your PC. Now the modem will think that your PC is connected directly to it. Now, see if it works as it should.

• Best way to completely ban firefox to make requests to certain areas? i.e., fb, twitter, youtube (for China)

  Being in China, all pages with forbidden sites take minutes to load; most of the time, firefox displays for a while 'loading platform twitter' or something similar, before finally to display the page with "small holes".
  So I would like to ban completely any attempt to connect to facebook, twitter and youtube (it would be even better if there was a list of sites that are censored in China).

  (There are also good reasons to ban the twitter and fb outside this threat).

  WARNING: it is there policy no statement in this post. I just want content that is authorized in China to show easily, without interference from content that I didn't want in the first place.

  You can use several different modules to prevent Firefox from loading certain sites. It is these favorites like:

  • BlockSite
  • LeechBlock
  • Plus: Add-ons for Firefox labeled "block"

  Each of these extensions block works differently, so to compare and find the one that works best for you.

• Symbol ban after new installation on new SSD

  Hello

  A few months ago, my original HD failed (MacBook Pro (13-inch, mid 2012)).

  I decided to replace it myself with a SSD instead.

  the thing is, every time you start, I get the symbol ban for a few seconds until sometimes for hours, but once the start is done - everything works perfectly.

  tried to replace the disc SSD 3 times now - the same result after each new installation of recovery of the internet.

  Currently, using SanDisk Ultra II 240 GB.

  Any suggestions?

  Thank you!

  The symbol you see means that the computer did not find a bootable system disk and sometimes occurs when you have not set up a default startup disk. Go to System Preferences, and then select Startup disk. You should see your SSD in the window. Select it after you unlock the preferences.

  The strange thing is that, if this is your problem, it must be solved in seconds - certainly not hours. This would suggest there is something more complex. You say that you tried to replace the SSD 3 times. Different drives? Different manufacturers?

• Is there something to do with the Xbox live servers?

  OT: live.

  I played a game on my Xbox with a few friends for a bit now without any problems and all of a sudden everybody gets expelled from the party and now it says I have no friends online. I can still play my game, but I can't connect with a friend. Is there something to do with the Xbox live servers or is it my Xbox one?

  Hello

  Your Question is beyond the scope of this community...

  I suggest that repost you in the Xbox Forums.

  "Xbox a Preview program FAQ.

  http://support.Xbox.com/en-us/Xbox-one/system/Xbox-update-preview-FAQ

  'Home'

  http://forums.Xbox.com/

  "Xbox forums.

  http://forums.Xbox.com/xbox_forums/general_discussion/f/3817.aspx

  _________________________________________________

  "Xbox Forums directory.

  http://www.Xbox.com/en-us/forums

  General

  • Home/FAQ/Forum policy

  • Community general discussion

  Material & Discussion Services

  • Equipment & Services

  Xbox support
  Agent hours: M - F 09:00-17:00 PT

  • Xbox 360 support

  • Xbox 1 support

  • Xbox on supported mobile devices

  • Xbox on Windows support

  • Networking of hardware information

  • Material information TV

  Law enforcement forums

  • Xbox 360 account Suspensions & Console bans

  • Account Xbox one & measures Console application

  Technical support of Xbox Live rewards
  Xbox Live rewards Squad hours: M - F 09:00-17: 00 PST

  • Xbox Live rewards program announcements

  • Xbox Live rewards Questions

  See you soon.

• See more HD in ban

  I have a X201T with a X 200 ban.  I swapped the stock HD in the Tablet and installed an SSD.  I put the HD in the ban to use for backups (via Rescue and Recovery).

  Since a few days ago, X 201 stopped seeing the backup HD.  I've uninstalled and reinstalled the drivers HD and he out the ban and put back in (ensuring that it was nice sitting).

  I used compressed air to blow out all the connections.  Still did not work.

  My BIOS is updated.  The Explorer Windows, no R & R can detect the HD.  However, oddly enough, when I hit F12 during initial start-up, it gives me the possibility to use the HD ban to start (is not bootable, it's strictly for backup).

  I ordered a box HD not expensive w / USB, so that I can remove the ban to see if it's the drive that put problem.  Then I remembered this community and its scholars Thinkpad Legion... did I miss something?

  Adam, thanks for responding.  The drive is not bootable (contains just backup images), so I don't mind back into the laptop.

  The box arrived and I was able to get the HD and scan with SeaTools.  The player has passed all the tests, but did not always show in Explorer (or Rescue and Recovery).  My assumption at this point was that I had a connection problem, but now it's clearly something else.

  I went into disk management and saw that I had a conflict of identification by car, which has been translated by the dock HD being the 'offline '.  I have reset it manually, and it works fine now.

  On the other hand, low-cost HD box is too short for good lock up the HD should I choose to get out of the docking station... but it was a value of $5 to diagnose the problem by about 5 mm.

• How to remove DNS queries for banned sites?

  Hello

  I'm looking to create a certain number of signatures to DNS queries for banned sites, the only way I've implemented successfully is to create a signature (string UDP), so he abandons all traffic UDP 53 containing the banned site regex string.

  I would like clarification from the experts to verify that this is the only way to do this, I know that there is a DNS Service engine, but I can't specify the COMPLETE domain name in this context. I don't know if I am missing something?

  Thank you very much

  You are on the right track. A personal signature of UDP is the only way you will find the applications that you want to remove.

  The DNS engine does not allow for the custom string matches.

  -Bob

• Lenovo X 41 ban-91 P 9283

  Is it possible to put an extra hard drive in this ban?

  Hi kstrid,

  Yes you can, with something like this . The SATA hard drive works at SATA speeds, but it will be faster than the stock hard drive PATA.

  Kind regards

  Dave

• Several monitors x201T with ban

  I'm looking for the simplest way to use 2 or 3 external monitors in mode 'Extend' with my x201T-0831 moored to the dock of 200 ban.  I don't need great resolution, just trying to keep organized with many projects using Outlook, Word, Excel, Powerpoint, etc. - several windows open at the same time.  Have VGA screens, but loans to buy more if necessary.  Would appreciate any help.  Found wires for other models of Lenovo referring to third-party products, but I can't say which is better for the x 201 for this type of need.

  Thanks for any help!

  Thank you, Danielle.

  I followed your links.  As I watch the T410s ban at http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-76519&selectarea=SUPPORT&tempsel..., it seems that the connectors are slightly different between the ban and the one I have, the x 200.  On the T410 ban, there are two DVI ports and a VGA port.  On the x 200 ban, there is a VGA port at the back, next to a DisplayPort, and there is no DVI port.  The x 201 Tablet has a VGA port on the left side of the tablet itself, but I'll assume that is disabled when the Tablet is rooted in the x 200 docking ban.

  I'll start with the assumption that I need to get a second monitor connected to the docking ban and use the DisplayPort port to do.   Since I was extra VGA monitors on hand, I'll buy Lenovo DisplayPort to VGA (analog only) cable from monitor part number 5794393 http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70321.  I'll try to get two VGA monitors upward and running in the configuration "Extend".  I will present on the progress made in the coming weeks.  Thank you.

  LeeWagner

  Update and additional comments:

  It is now December 3, 2010, twelve days after that I started this answer.  Additional measures:

  1. I looked more closely at two monitors that I have, and have all both DVI and VGA ports.  I realized that most of the monitors, at least for the past five years, have this system double connector - I just used the VGA connector since it's what I do since the 1980s and I never had a reason to learn more about DVI.  I decided it was the right time to learn something new.

  2. I ordered the single-link DVI - D Monitor Cable DisplayPort / http://shop.lenovo.com/SEUILibrary/controller/e/web/LenovoPortal/en_US/catalog.workflow:item.detail?...

  I found this on the main Web page of Lenovo USA by following the links store > Accessories > cables and connectors.  This is the fourth element displayed on the first page.  Cost of $27.13 including taxes and delivery United States.  Arrived today, so 12 days to fill orders.  The cable has Lenovo part number 45J7915.  Of interest, the date of manufacture for the part is '2010-11-27' and 11/29 China shipping date.  This looks like something that could probably also be purchased in both major electronic supply store.

  3. I followed the instructions at http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-76519&selectarea=SUPPORT&tempsel..., kindly provided by Danielle.  I found that it worked better print 3 pages of instructions so that I have didn't disable images of instruction I changed monitors.

  4. I thought that instructions, intended to be the ThinkPad T410s, were very clear and I just had to adjust my thinking a bit because the X 200 ban has a different configuration for the connectors on the back.  On the X 200 ban, the connector remains blue VGA of the Middle when seen from behind.  There is only a single DisplayPort connector rather than two, and that is a black (not white) just to the left of the blue VGA port.

  5. After following the correct sequence listed in steps 1 through 4, I found that my monitor connected to the VGA port, designated as "Monitor 2", remained black.  I had a picture on the Thinkpad x201T (listed as "monitor 1") and the DVI monitor, listed as "monitor 3".  I was able to use both monitors in extend mode, so that I could drag the arrow of the mouse smoothly through to the next screen.

  6 I then to the "Troubleshooting" of this same step "Setup multiple views for ThinkPad T410s", more precisely in the line:

  "If you followed steps 1 through 4 and one or more of your screens does not connect, then you must change the display screen resolution."

  By clicking right on the display screen, I was introduced to the great tool for the configuration of multiple screens.

  I had several stumbling blocks to work through, and my experience could be useful to other readers:

  (a) I confirmed what others have said I am only able to watch two monitors, not three, with this configuration.

  (b) Resolution display is a misleading title of the window that appears when you have more than one monitor connected.  A more accurate title would be "set up multiple monitors - select duplicate or extend Mode, decide who monitors, designate which monitor is the primary monitor is connected and disconnected, and set the resolution for each monitor.

  (c) the configuration that I opened the screen resolution window showed that 1 monitor, the ThinkPad LED display, the VGA monitor as Monitor 2 and DVI Monitor 3 monitor.  The physical layout on my desk, from left to right, was 2-3-1.  The DVI monitor features a 22 "display, VGA has 19" and I wanted the larger screen directly in front of my external keyboard and mouse.   Resolution of the pictorial display screen showed the monitors installed (from left to right) 3-2-1, 3 and 1 blue and (active), and 2 gray (inactive).  I got confused trying to drag the mouse from one screen to the other to the first mouse seems to hit the left wall of the ThinkPad screen and and do move to the left on my screen more grand, who showed a great wallpaper.  I finally realized that if I moved the arrow to the right wall of the ThinkPad, he moved smoothly on the big screen.  The mouse arrow and screens are behaving as the pictorial resolution screen display showed the monitors built (from left to right) 3-2-1, not that I had actually prepared physically on the my table.  I was fooling around with by dragging images autour in display screen resolution pictorial until this photo with the real physical layout.

  (d) I had to then select the left (VGA) monitor as the primary monitor.  I've learned to follow the caveat to push "Apply" with each individual before moving on to the next step.

  (e) once I had unchecked the main monitor, the screen of ThinkPad, I was free to designate the ThinkPad screen as 'disconnect this Display.

  (f) once the ThinkPad screen was off, I was free to choose monitors 2 and 3 as active monitors in extended display Mode and move the mouse easily throughout the whole of the left edge of the screen 2 (my monitor of the left hand) to the right edge of the monitor 3 (my Center and the larger screen).  1, the ThinkPad screen monitor, remained gray.

  (g) a minor bug, when I clicked on the 'Apply' button for each of these changes, nothing happened.  I have to click it a second time to apply to commit.  (I use Windows 7 x 64, updated weekly)

  (h) another minor obstacle was that I had to get the best resolution for a monitor before I designated as primary monitor.  I got stuck a couple of times with a resolution too large, unable to see all of the icons or the taskbar in Windows 7.

  (I) now that I'm all together to the top with several monitors, my first experience, I realize that a more fluid experience would be if all monitors were of the same size of the screen, closely aligned together at the same height.  With my current setup, a monitor is 3 "higher than next to him, and the resolution is different between the two screens. MTY eyes must make two adjustments that I scan back between two screens.

  Thanks to James for his excellent help!  It also has the same information published on the website of T4190s: http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/How-do-I-setup-multiple-display-for-the-Thi...

  LeeWagner

   

   

• Download something on safari Version 10.0 (11602.1.50.0.10)

  Can someone again about my safari once more.

  I use Safari Version 10.0 (11602.1.50.0.10), I can't download anything because the AdBlock.

  I already disabled, or even uninstall my AdBlock and restart my Safari and my laptop, but still have

  the same problem. The warning is written as:

  "Oops!" Detected... AdBlock! to disable AdBlock and reload your page. »

  Can anyone tell my how to remove it so that I can download something using safari? Thank you.

  Go to Finder and select your user folder. With this Finder window as the windshield, select Finder/display/display options for presenting or order - J.  When the display options opens, check "show the library folder. This should make your visible user library folder in your user folder.  Select LibrarySafari/Extensions. Remove it from there.

• Maybe clicked on something that I should not have... Advice please!

  A window appeared on my browser (latest version of chrome on a MacBook of 2015 using the latest OS) which resembles an investigation legitimate from my ISP. Recently I had problems with them and my alarm has not extinguished quickly enough. It is curious that this window has appeared without an email but it didn't fully if register because my ISP has pop-up warnings apparently. I have NEVER had a pop up - but - due to some questions by e-mail, my firewall is down and I forgot to put up again.

  Yes, as the fog cleared I had already clicked through the investigation and he offered a free gift and that's when I realized that I should immediately stop the window. I haven't entered ANY info, never filled out a form, or I don't have to download anything. I installed Malwarebytes for Mac and he came clean.

  My concern: could I have gotten something malicious as a key logger or some other identity stealing malware simply by clicking on the poll? I think they call it a drive by?

  I'm a meticulous time machine user, so I have a complete backup of 99% of my system hard disk external. I should burn the Earth just to be sure?

  ... I haven't entered ANY info, never filled out a form, or I don't have to download anything.

  Then you have no reason to worry.

  Could I have gotten something malicious, as a key logger or some other identity stealing malware simply by clicking on the poll?

  Keylogger No.. At for example requires authentication to install.

  The survey was a ruse to try to get you to reveal personal information. There are several varieties of this scam. They are remarkably successful, but you didn't fall for it. No further action is necessary or justified.

  Consider reading some of these tips to use:

  Effective defenses against software malware and other threats

  Phony 'technical support' / 'ransomware' popups and web pages

  Beware of fake Adobe Flash "installers".

  How to install the adware

• Pop - up said I won something

  I was surfing the web on my iPhone 6 when I opened a page in Safari and this up to pop said I was the 1 000 visitor and I won something. Obviously fake but is - it possible just looking one that pop up to a given my iPhone a virus?

  It is possible that you have a virus.

• Apple changed something in the Sierra preview

  I used to be able to open a .pdf file, sign it and add text to some other fields, save it, and then reopen it in Adobe Acrobat in order to ensure that the information has been saved. Send it to a contractor and had no problem to read information, but now after the installation of macOS Sierra it won't save not right, and the contractor can't see all of the fields that I've entered the information on.

  Now, I have to go back to the printing of the documents, complete rescan manually, and they are sent by e-mail. A big waste of time.

  Something has changed.

  Since the switch to the Sierra, using Quick Look to view the PDF files (it is when you click on a file in the Finder and press the space bar for an overview) all fields appear empty.

  Then when you use Preview (version 9.0) to view and edit pdf fields, any field you click on edit is blocked immediately with a double "shadow" of the text, so you don't see what you are editing.  When the pdf file is saved, other applications like Adobe Reader see the fields as empty, unless you click the field, and then you can see one at a time.

  I used the feedback Wizard Apple to bring this issue to Apple.  If all goes well they will see the problem and fix it.

  I use Preview in OS Lion to fill pdf forms for the moment.   And keep on improving my MacBook Air to Sierra for awhile.

• On my MBP, 2011, bar menu in recovery mode to offer only one option - selector of language. How do you get Terminal? Missing something?

  On my MBP, 2011, in recovery mode menu bar offers only a single - switch language option. How do you get Terminal? Missing something?

  You will need to choose your language first.

  From there on, the Terminal will be on the menu drop-down utilities > Terminal

• I El capitan, but stopped opening safari says impossible to find something wrong with the application extension

  I El capitan, but stopped opening safari says impossible to find something wrong with the application extension

  You can open it by accessing it in the Applications folder? If so, you may have a corrupt Dock alias. Click and hold the alias and make it about 1 inch away from the docking station, then release. Then drag the application in the Applications folder in the Dock to create a new alias. When you have a new alias, control - click/Options/keep in Dock.