Are these hardware or software errors?

Similar Questions

• Computer laptop G62 crashed and now it gives error "unable to open because of the recent hardware or software error"

  I have a new problem with my PC. My laptop suddenly crashed. It was working fine before this, but while I was watching a movie, it's just off. I tried to restart but it gave me the error that it cannot open because of software or a hardware error. It gives me two options: 1. to try the Startup Repair tool. 2. to open Windows normally.

  I tried to open it normally, but it redirects me to startup repair. The Startup Repair is unable to do anything.

  =================================================================================

  Startup Repair can try to restore your computer to an earlier point in time when it worked correctly.

  This repair will not personal data change, but it can remove some programs that have been installed recently. You can't undo this restoration.

  =================================================================================

  Then I tried to restore my PC to a previous restore point, but it won't let me continue once I've selected a point. It only shows my C drive which is grayed out so I can't select and continue. It gives me a yellow warning saying that the Protection of the system disk must be enabled.

  So as the restoration is not an option, I went to the recovery of the system where it will restore my factory settings, deleting all data. The problem is that I have a lot of valuable data in the PC, so I don't want to do this before you have a back-up. I tried to make the back-up, but the first back-up was arrested at 78%. The second he stopped at 13%. After that all other attempts to create a backup stops at 25%.

  I don't understand what to do. People say it's a problem with Windows 7 (64-bit). I don't have a Windows 7 CD either because it was pre-installed when I brought. I have an original CD of Windows Vista so I'll try to install first. Then, I'll try to copy my data and then restore my laptop to its factory settings. I hope this works.

  A guy suggested to replace the names of readers. So I reversed the C drive and D drive. He showed me all the readers in the restore option. But the restore has failed. Then he renamed automatically drives to their original state. I even ran sfc/scannow, but it shows me that a scan is planned and restart the PC to start. But when I reboot, it gives me the same thing again.

  Please suggest what to do...

  I installed Windows Vista professional from the CD. It worked perfectly... I want to say that I was able to retrieve all my data because it stored in a folder called Windows.Old

  But since I could not the wifi adapter and integrated graphics card Intel to work on the PC, I tried to restore factory settings. It doesn't let me access the Recovery Manager by pressing F11 on reboot I went to the computer icon and right-click on it. I selected manage and made my recovery disk a partition active. So after reboot it properly started the Recovery Manager. Right now I'm it back to factory settings. I'll let you know what happens after that. My data is safe, but I don't know if I'll be able to load my original OS.

• space bar works well even when I plug microsoft 4000 keyboard it's a hardware or software error?

  When the space bar is used for spacing, it works. But it is more raised guns when you play. I removed and cleaned the SPACEBAR with no result. Please inform, I'm not computer literate and I have no idea. Sincerely, Allan Chase

  Hello

  -What is the name of the game you play? Is this game online, or is it installed on the computer?
  -Is it a cable or a wireless keyboard?
  -Are all the other keys of the keyboard works correctly when this game?
  -Was the same control well before work? If Yes, did you change the game settings?

  Allan, when the space bar works correctly when you try to give spaces when entering; This means that it works very well.

  Might be the reason why it does not work when you are firing cannons in playing games, the game keyboard control settings have been changed by you or other default keys to fire.

  So, I suggest you to check the game support for better assistance Web site.

  Hope this information helps.

• Error: "corrupted error reports are rare. They can be caused by hardware or software problems and usually indicate a serious problem with your computer. »

  Original title: my computer was "rebuilt" with all the new parts June 2011. Logging on his shot and miss it may stay on or shut down and restart. I have this message when I turned on my pc this afternoon:

  Corrupted error report.

  Unfortunately, the error you report submitted is corrupted and cannot be analyzed. Reports "damaged errors are rare. They can be caused by hardware or software problems and usually indicate a serious problem with your computer.

  When I turned on pc today is showed a blue screen and can something on a disc because the disc did not work properly?

  I paid for all the new parts for my computer and the computer technician has assured me that all the work was completed and correct. I bought the power supply (1) mother board, cards (2) 1 TB of memory. (2) hard drives 1 TB. (1) card reader and other elements appearing on my Computer Geek Bill.

  My music files are no longer mp3 but .oma. He/the Tech added its own files and records of music of World War II. These game. The drive D drive or slave who held my music, he said he wiped clean.

  I need to know these error reports will completely close my pc and all the information will be lost?

  Hi satindoll11233,
   
  I recommend you to disable the auto reboot system error (this option prevents Windows to reboot automatically if a Windows error to fail) of the startup options safe mode to know the exact error message or error code originally this problem.
   
  For more information, see:

  A description of the options to start in Windows XP Mode

• Error when you try to install Windows XP Service Pack 3: "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.

  Windows XP SP3 problem

  Recently, I met a problem with my PC and was forced to use the system recovery. Now I'm back to factory settings and try to install Windows XP Service Pack 3 on my computer. Windows Update won't work for me, that whenever I try to update I get [error number: 0x8024400A]. I think it's because I use Service Pack 2, or that's what I concluded after researching the problem, anyway.

  This is not my real concern, however. Because I could not get the update automatically, I tried to download and install the "Windows XP Service Pack 3 Network Installation Package for IT professionals and developers" myself. The first time I did it, I restarted the PC after the installation and was met with "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this. "  I went into safe mode and went to a just system restore point before SP3 was installed, but now I don't know how to install it correctly without encountering this problem after reboot. I'm hardly the easy just stick with SP2 when there are potentially important available updates. How can I get Windows Service Pack 3 is installed on my PC?

  It's certainly interesting!

  If the cause of your problem is to have a HP PC with an AMD processor and an original image on your hard drive (and of course it sounds like this is the case), the solution should be to rename the file intelppm.sys and launch the sp37394.exe patch. Once done, the SP3 file that you downloaded from here:
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24
  SHOULD work!
  I'm puzzled why there is no intelppm.sys file in your directory C:\WINDOWS\system32\drivers.
  Since you recently returned to square one with your PC ("return to factory settings"), then you may as well run the patch from this page:
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&DLC=en&softwareitem=PV-60484-2
  and try the SP3 Setup file again.
  But, first, let's be absolutely sure that we are both using the same terminology. Please answer the following questions:
  1. have you safely backed up ALL your data?
  2. what method did you use to ride "back to factory settings? I think that your choices have been a destructive restore (full) and a (partial) non-destructive recovery. The first erases the disk and leave you with a pristine image and NOTHING ELSE (which means that all of your programs and data get deleted). The other (which does not always correctly) is supposed to leave programs and data intact.

• The following error during the installation of Windows: "cannot start Windows. A recent hardware or software change might be the cause.

  Help, please! Installing Windows Interrupted!

  Hi recently my computer was giving me a bit of concern for example (running slow, do not easily light etc...). A couple of days, my computer has decided not to put on after a glance on the net (on my other computer), I found I had a problem call KSoD or black screen of death, therefore I went on youtube and made all the different things said youtubers can fix this how ever none of these things worked, so finally I decided that I would have factory reset my computer/windows to using the system restore. However, at half way through the installation of windows after the factory reset (my computer came with no disk Windows), my computer has decided to remove what I believe to be called a blue screen of death, that this happened before and I thought it was part of the installation but when I turned my computer on he showed at the bios screen , but then it said 'unable to start Windows. A recent hardware or software change might be the cause. To solve the problem: 1. Insert your windows installation disc and restart your computer. 2. choose your language settings, and then click Next. "3 click on repair your computer ' all this is very well apart from the fact that I do not have the windows installation disc. I'm stuck at this screeni however have a disc of windows 7 and that he was going to install windows7 after I got my vista Setup! but the only I see is the bio screen so I was wondering if there was some way I could install windows 7 from the bios or simply delete the entire half installed this error files windows vista from the bios screen? Please, any help is greatly appreciated. Or get a new internal HDD would fix the problem aswell?

  Hello

  You can check out the following link and check:

  Installation and reinstallation of Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  See also, how to start your computer from a Windows 7 installation disc or USB flash drive.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-from-a-Windows-7-installation-disc-or-USB-flash-drive

  Note:

  If the copy of Windows 7 is an upgrade, you will need to install a full version of Windows Vista and then upgrade to Windows 7

  I hope this helps!

• Error on startup: "Windows cannot start. A recent hardware or software change might be the cause.

  Original title: is that what Microsoft offers downloadable boot for Vista drive data

  I have a Windows error recovery when Windows does not start. A recent hardware or software change might be the cause.

   
  Loops in this form BACK to watch as it starts, it then restores to the error recovery screen.
  I need information from the startup disk so that I can read my Dell Inspiron 531 Windows disc and if all goes well the error; Download a Microsoft?

  Hello

  try a system restore of 1st

  If this does not download and use a startup, the ERD etc. neosmart

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Error message: Windows could not open possibly due to a hardware or software upgrade with a black screen and white on Windows XP starts.

  Original title: suddenly Windows XP does not open

  After using the computer someday, he would not start the next time I lit. Windows tried to start but failed and went to a black and white screen saying windows could not open possibly due to a hardware or software upgrade and invites me to try opening windows normally, safe mode, using the last well-known congig, etc... Every choice has ended up doing the same thing, windows tries to start and end up back in the black and white screen.

  Hi Brian,.

  1. you receive messages or error codes?

  2. did you of recent changes on the system?

  You can read the following article and check if it helps.

  Computer stops responding with a black screen when you start Windows XP

  Black screen on startup

  Hope this information is useful.

• In XP, error at startup 'Windows couldn't start. A recent hardware or software change might be the cause.

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert your Windows installation disc and restart your computer.

  2. choose your language settings and thenk click 'next '.
  3. click on "repair your computer".

  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.

  File: \Windows\system32\winload.exe

  State 0 xC0000001
  Info: The selected entry could not be loaded because the application is missing or damaged.

  But, instead of file: \Windows\system32\winload.exe I get file: \$Windows.~BT\windows\system32\winload.exe.
  

  Hi imranhussain1979,

  ·         You have made any changes recently?

  ·         When it was working fine?

  ·         You have Windows XP or a later version of Windows?

  Step 1: The error seems to refer to a later version of Windows. Restart the computer and check if the installed operating system.

  Step 2: Try to start the computer in safe mode and check the number.

  Start your computer in safe mode

  Microsoft Windows XP: start the computer in safe mode

   

  Respond with more information so we can help you best.

• When you try to run a system recovery I get this error: cannot start Windows. A recent hardware or software change might be the cause. OxcOOOOOOf

  When you try to run a system recovery I get this error; OxcOOOOOOf

  Original title: error OxcOOOOOOf

  My laptop crashed. I used my initial recovery to start. I get a message from Windows Boot Manager as follows:

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert Windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."

  If you do not have this disc, contact you system administrator or computer manufacturer for assistance.

  File: \Windows\system32\winload.exe

  Status: OxcOOOOOOf

  Info: Seelected entry could not be loaded because the application is missing or damaged.

  It does not work. Suggestions and no, I have not modified before the crash.

  I loaded my recovery disk for my 32-bit home edition of vista Hp pavilion dv6700 cto entertainment lapt top and after going through the recovery process I just get this mechioned of the screen in the original question. How ever during my recovery process never got far enough to enter my product code, he asked just a two disc and disc supplamentry and then gave me a blue screen black for a minute or two then rebooted and showed the failure of start OxcOOOOOOf screen... what should I do?

  Hi Anthony206,

  Since you've already tried to use the Windows Vista recovery disc has received from the Original Equipment Manufacturer (OEM).

  From now on, you can only contact OEM for the use of the recovery feature.

  I hope this helps.

• Apple Hardware Test reports error message

  If you want history, scroll to the bottom. Here's the short version: Apple Hardware Test indicates error 4SNS/1/40000001:VeAS-0.000

  This page handy tells my that '4SNS' = a sensor problem. 'V' indicates that it is a voltage sensor; and 'e' is short for PCIe. There is nothing on AS - 0, 000 but I'll allow myself that it could indicate the location PCIe 0, i.e. the bottom, 16 channels gpu 'main' slot. If anyone can confirm or correct this assumption, that would be sweet.

  Most important: how serious a mistake it is? I have a Radeon HD 7970 GHz 3 GB edition. I'm he put at risk by continuing to use it? I plan to play a lot more, some on El Capitan, but more on Windows, where I can experiment with overclocking my already factory overclocked GPU. It doesn't seem to be a problem in terms of overclocking software is. Reports of tension, times and speeds of fan exactly as expected.

  And the main reason I upgraded from my great MacPro1 OG, 1 to a 4.1 is because I intend to upgrade GHz W3520 2.66 in the 4.1 to a 3.46 GHz W3690. With the upgrade of the processor, I had planned to keep this box for several years. This error indicates that this particular Mac Pro is less great, or maybe even a lemon?

  The seller is apologetic and will accept a return. Which will cost me $40. I would stay there or is it really not a problem. It was really a lot...

  As you stock up on for Apple hardware Test error messages are very cryptic and not really documented.

  I don't know of anyway to know if it's a "fatal" flaw

• The MIG 229771 in c# software error

  Hello

  I use an NI USB-6009 data acquisition.

  I'm unable to create a task using c#, I get a MIG 229771 software error when I try to instantiate with 'myTask1 task = new Task();' or 'task myTask1 = DaqSystem.Local.LoadTask ("D00");' but not when I create a reference ' Task myTask1;

  I get no error when I run the projects in the sample or when I use measurement and Automation Explorer.

  I have added the following references to my project both have a runtime version v2.0.50727:

  1. "C:\Program NIUninstaller Instruments\MeasurementStudioVS2008\DotNET\Assemblies\Current\NationalInstruments.DAQmx.dll" version 9.2.35.32
  
  
  2. "C:\Program NIUninstaller Instruments\MeasurementStudioVS2008\DotNET\Assemblies\Current\NationalInstruments.Common.dll" version 8.9.35.302

  These references appear to be the same as those used in the examples of projects that I can tell.

  As in the projects in the sample, I added the NationalInstruments.DAQmx using statements.

  I've updated my software to version "NIDAQ921f0".

  I use Visual Studio Professional 2010 and I am targeting .NET 3.5 framework.

  I use Windows7 professional 32-bit with admitting privileges.

  I don't have LabView or Measurement Studio.

  I have read the messages for the error message and taken the following steps:

  1. I have repaired/reinstalled the software.
  
  
  2. I confirmed that the services mentioned in the messages are running.

  My .NET framework helpfiles located via the start menu are missing and I have not used c# to control the DAQ before so I could miss something basic.

  Any suggestion would be appreciated.

  Thank you.

  Hi George,.

  Thank you to detail the steps that you have already done, when you say that the examples work fine what they call the start task DAQmx in the same way you are attempting your project? Also you mention that you use a Measurement Studio still your references in the project come from a MeasurementStudio path?

  The only other reason for such an error that I could find was in regard to security issues, you launch McAfee or software NOD32 anti-virus, could you try the program with this disabled in order to see if some material of third party is at the origin of the conflicts with the start method of task?

  Kind regards

• My computer is a HP Pavilion slimline and my printer is a Dell 968. I can't print from my computer, are these compatible?

  My computer is a HP Pavilion slimline and my printer is a Dell 968.  I can't print from my computer, are these compatible?

  Hello

  ·         What happens when you try to print?

  ·         You get an error message or code?

  Your Dell 968 printer is compatible with Windows 7, check out the link:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=hardware&s=Dell%20Printer%20968%20

  Method 1:

  Try to install the latest driver on the Dell site and check if it helps:

  http://support.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R241825&SystemID=PRN_ALL_A968&servicetag=&os=WV64&osl=en&deviceid=15344&devlib=0&typecnt=0&vercnt=2&catid=-1&impid=-1&formatcnt=0&libid=40&typeid=-1&dateid=-1&formatid=-1&source=-1&fileid=349071

  Method 2:

  Follow the steps in troubleshooting section and check if that helps:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might caused ha this.

  We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might caused ha this.

  Hello ILO,.

  1. When you receive the error message?

  2. are you able to boot to the desktop?

  3. did you of recent changes on the computer?

  Method 1

  If you are unable to start windows check to see if you can boot into safe mode.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Method 2

  If you are able to boot into safe mode then I would suggest that you do clean boot and check.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Hardware or software conflict?

  Problems with USB adapter for sagem wi - fi, network freeze all the time and therefore VERY unstable Internet, BSOD problems connection (a LOT). This, the software being updated through windows update, cleaned of unnecessary software, reconfigured start up with the command "msconfig", the updated drivers via Device Manager but that did not help because after the digitization of 14 obsolete found drivers drivers need more updated (online driver update software too expensive!) What to do next? I was at my computer for 3 days in a row! The network actually works because with my iPad, I have zero problems, it looks like a hardware or software incompatibility with my pc (OS Vista professional) problem. Maybe I need a new PC? Help!

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  If you are overclocking STOP

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  Please follow these instructions to collect data against crashes and upload them here, to your Skydrive or a service such as Rapidshare file sharing.

  http://www.SysNative.com/forums/showthread.php/68-blue-screen-of-death-%28BSOD%29-posting-instructions-Windows-8-7-amp-Vista?p=303&viewfull=1#post303

  http://SysNative.com/0x8/BSOD_Windows7_Vista_v2.64_jcgriff2_.exe

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.
  * Zip up the contents of this folder
  Please, upload to skydrive or a file sharing service and put a link to them in your next post.

  Go to start > search/run > cmd > msinfo32 and include it in the upload

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.
  * On the Advanced tab, click Startup and recovery... Settings button.
  * Make sure that automatically restart is unchecked.
  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).
  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.
  * OK your way out.
  * Reboot if changes have been made.

  http://www.SysNative.com/forums/showthread.php/325-BSODs-but-no-dump-files

  http://www.osronline.com/article.cfm?article=545

  Please also go to start > run > msinfo32 and record the results.  Send it with the DMP files, thank you.