ASA 5505 VPN Client Ipsec config problems
I configured the asa the wizard to Setup vpn, but this still does not work properly. Vpn connect without problem, but I can't access all the resources on the 192.168.1.x subnet. Don't know what I'm missing here, here's a copy of my config.
ASA Version 8.0 (3)
!
host name
domain name
activate the password
names of
!
interface Vlan1
nameif inside
security-level 100
192.168.1.3 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
"Public ip" 255.255.255.0 IP address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 192.168.1.28
domain fmrs.org
GroupVpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
vpngroup_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access will permit a full
inside_nat0_outbound list of allowed ip extended access all 192.168.99.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
inside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 any
access extensive list ip 192.168.99.0 inside_access_in allow 255.255.255.0 any
inside_access_in list of allowed ip extended access all 192.168.99.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.99.2 - 192.168.99.100 255.255.255.0 IP local pool GroupPool
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 602.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 192.168.1.0 255.255.255.0
public static tcp (indoor, outdoor) interface 192.168.1.62 pptp pptp netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 66.76.199.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server fmrsdc
fmrsdc AAA-server 192.168.1.28
Timeout 5
fmrsasa key
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
GroupVpn internal group policy
GroupVpn group policy attributes
value of server WINS 192.168.1.28
value of server DNS 192.168.1.28
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list GroupVpn_splitTunnelAcl
FMRs.org value by default-field
ID password cisco
tunnel-group GroupVpn type remote access
attributes global-tunnel-group GroupVpn
address pool GroupPool
authentication-server-group fmrsdc
Group Policy - by default-GroupVpn
IPSec-attributes tunnel-group GroupVpn
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the pptp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:b5df903e690566360b38735b6d79e65e
: end
Please configure the following:
ISAKMP nat-traversal crypto
management-access inside
You should be able to ping of the SAA within the IP 192.168.1.3
Tags: Cisco Security
Similar Questions
-
ASA 5505 VPN to IPSec website DOES NOT CONNECT
I spent 2 days already to try to get 2 ASA 5505 to connect by using an IPSec vpn tunnel. I can't understand what im doing wrong, I'm using 192.168.97.0 and 192.168.100.0 as my internal networks that I am trying to connect via a link directly connected on the outside with 50.1.1.1 and 50.1.1.2 interfaces such as addresses (all 24). I also tried with and without active NAT. Here is for both of the ASA configs, the vpn config was conducted by the ASDM, but I also tried the approach of the command-line without success. I followed various guides to the letter online, starting with an empty config and factory default. I also tried the IOS 8.4.
ASA 1 Config ASA 8.3 Version (2)
!
VIC hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.97.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 50.1.1.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
boot system Disk0: / asa832 - k8.bin
passive FTP mode
pager lines 24
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.97.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:4745f7cd76c82340ba1e7920dbfd2395
Config ASA2 ASA 8.3 Version (2)
!
hostname QLD
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 50.1.1.2 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
passive FTP mode
network of the SITEA object
192.168.97.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
outside_1_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 object SITEA
pager lines 24
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 static destination SITEA SITEA
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.100.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 50.1.1.1
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
tunnel-group 50.1.1.1 type ipsec-l2l
IPSec-attributes tunnel-group 50.1.1.1
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d987f3446fe780ab5fbb9d4213b3adff
: end
Hello Mitchell,
Thanks for letting us know the resolution of this topic.
Please answer the question as answered so future users can learn from this topic.
Kind regards
Julio
-
LAN ASA 5505 VPN client access issue
Hello
I'm no expert in ASA and routing so I ask support the following case.
There is a (running on Windows 7) Cisco VPN client and an ASA5505.
The objectives are client can use the gateway remote on SAA for Skype and able to access devices in SAA within the interface.
The Skype works well, but I can't access devices in the interface inside through a VPN connection.
Can you please check my following config and give me any advice to fix NAT or VPN settings?
ASA Version 7.2 (4)
!
ciscoasa hostname
domain default.domain.invalid
activate wDnglsHo3Tm87.tM encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan3
prior to interface Vlan1
nameif dmz
security-level 50
no ip address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
DNS server-group DefaultDNS
domain default.domain.invalid
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any
inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 any
outside_access_in list of allowed ip extended access entire 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPNPOOL 10.0.0.200 - 10.0.0.220 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 10.0.0.0 255.255.255.0
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (outside) 1 10.0.0.0 255.255.255.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 5
SSH version 2
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.1.2 - 192.168.1.33 inside
dhcpd dns xx.xx.xx.xx interface inside
dhcpd allow inside
!
attributes of Group Policy DfltGrpPolicy
No banner
WINS server no
value of server DNS 84.2.44.1
DHCP-network-scope no
VPN-access-hour no
VPN - connections 3
VPN-idle-timeout 30
VPN-session-timeout no
VPN-filter no
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
disable the password-storage
disable the IP-comp
Re-xauth disable
Group-lock no
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelall
Split-tunnel-network-list no
by default no
Split-dns no
Disable dhcp Intercept 255.255.255.255
disable secure authentication unit
disable authentication of the user
user-authentication-idle-timeout 30
disable the IP-phone-bypass
disable the leap-bypass
allow to NEM
Dungeon-client-config backup servers
MSIE proxy server no
MSIE-proxy method non - change
Internet Explorer proxy except list - no
Disable Internet Explorer-proxy local-bypass
disable the NAC
NAC-sq-period 300
NAC-reval-period 36000
NAC-by default-acl no
address pools no
enable Smartcard-Removal-disconnect
the firewall client no
rule of access-client-none
WebVPN
url-entry functions
HTML-content-filter none
Home page no
4 Keep-alive-ignore
gzip http-comp
no filter
list of URLS no
value of customization DfltCustomization
port - forward, no
port-forward-name value access to applications
SSO-Server no
value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information
SVC no
SVC Dungeon-Installer installed
SVC keepalive no
generate a new key SVC time no
method to generate a new key of SVC no
client of dpd-interval SVC no
dpd-interval SVC bridge no
deflate compression of SVC
internal group XXXXXX strategy
attributes of XXXXXX group policy
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelall
Split-tunnel-network-list no
XXXXXX G910DDfbV7mNprdR encrypted privilege 15 password username
username password encrypted XXXXXX privilege 0 5p9CbIe7WdF8GZF8
attributes of username XXXXXX
Strategy Group-VPN-XXXXXX
username privilege 15 encrypted password cRQbJhC92XjdFQvb XXXXX
tunnel-group XXXXXX type ipsec-ra
attributes global-tunnel-group XXXXXX
address VPNPOOL pool
Group Policy - by default-XXXXXX
tunnel-group ipsec-attributes XXXXXX
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23
: end
ciscoasa #.
Thanks in advance!
fbela
config #no nat (inside) 1 10.0.0.0 255.255.255.0< this="" is="" not="">
Add - config #same-Security-permit intra-interface
#access - extended list allowed sheep ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0
#nat (inside) 0 access-list sheep
Please add and test it.
Thank you
Ajay
-
ASA 5505 VPN sessions maximum 25?
Hello friend´s
The company I work when acquired several ASA 5505, so now we will be able to connect several branches at Headquarters. But, now, I know that the ASA 5505 just scalates to 25 VPN sessions, I think that it won´t be enough to support the operations of an office. I have a lot of questions about this:
Is - what the number 25 menas supporting up to 25 L2L tunnels? Or it means 25 sessions, regardless of the amount of L2L tunnels?
Is this the way number 25 supporting up to 25 users in the Branch Office? Or it means that a user can use several sessions?
I'm the stage of testing in a laboratory where one PC connects to many applications, at - it now someone if there is a command in the SAA to check how many VPN sessions is used?
Please, do not hesitate to ask as much as necessary information. Any comments or document will be appreciated.
Kind regards!
Hi Alex,
The assistance session 25 ASA 5505 VPN as max for IKEv1 or IPSEC tunnels customers it could be up to 25 L2L tunnels or 25 users using ikev1 (Legacy IPSEC client) and another 25 sessions for Anyconnect or Webvpn in this case are used in function.
To check how many sessions VPN is currently running, run the command 'Show vpn-sessiondb' and 'display the summary vpn-sessiondb '.
Find the official documentation for the ASA5505 on the following link:
Rate if helps.
-Randy-
-
Problem with ASA 5505 VPN remote access
After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?
Here is the cfg running of the ASA
----------------------------------------------------------------------------------------
: Saved
:
ASA Version 8.4 (1)
!
hostname NCHCO
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
network of the NCHCO object
Subnet 192.168.2.0 255.255.255.0
network object obj - 192.168.1.0
subnet 192.168.1.0 255.255.255.0
network object obj - 192.168.2.64
subnet 192.168.2.64 255.255.255.224
network object obj - 0.0.0.0
subnet 0.0.0.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the Web server object network
the FINX object network
Home 192.168.2.11
rdp service object
source between 1-65535 destination eq 3389 tcp service
Rdp description
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0
inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224
outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
LAN_Access list standard access allowed 192.168.2.0 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
outside_access_in list extended access permit tcp any object FINX eq 3389
outside_access_in_1 list extended access allowed object rdp any object FINX
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 649.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0
NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64
NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
the FINX object network
NAT (inside, outside) interface static service tcp 3389 3389
Access-group outside_access_in_1 in interface outside
Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http *. **. ***. 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform
IKEv1 crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHCO group policy
NCHCO group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1
value by default-field NCHCO.local
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username NCHvpn99 password dhn. JzttvRmMbHsP encrypted
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
IKEv1 pre-shared-key *.
type tunnel-group NCHCO remote access
attributes global-tunnel-group NCHCO
address pool VPN_Pool
Group Policy - by default-NCHCO
IPSec-attributes tunnel-group NCHCO
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
ASDM image disk0: / asdm - 649.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
---------------------------------------------------------------------------------------------------------------
And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:
---------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7601 Service Pack 1
Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026
Try to find a certificate using hash Serial.
2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027
Found a certificate using hash Serial.
3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011
RELOADED successfully certificates in all certificate stores.
4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002
Start the login process
5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is NOT behind a NAT device
21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F
SPLIT_NET #1
= 192.168.2.0 subnet
mask = 255.255.255.0
Protocol = 0
SRC port = 0
port dest = 0
45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local
46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710
47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11
49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now
57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">
59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify is set to 28800 seconds
60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***
61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059
IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)
62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025
OUTGOING ESP SPI support: 0xAAAF4C1C
63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026
Charges INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001
Launch VAInst64 for controlling IPSec virtual card
66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034
The virtual card has been activated:
IP=192.168.2.70/255.255.255.0
DNS = 192.168.2.1, 8.8.8.8
WINS = 0.0.0.0 0.0.0.0
Domain = NCHCO.local
Split = DNS names
67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038
Were saved successfully road to file changes.
69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036
The routing table has been updated for the virtual card
71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A
A secure connection established
72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 96.11.251.149. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 192.168.2.70. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001
Did not find the smart card to watch for removal
75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0x1c4cafaa in the list of keys
78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0xc5bfbe3e in the list of keys
80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F
Assigned WILL interface private addr 192.168.2.70
81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037
Configure the public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046
Define indicator tunnel set up in the registry to 1.
83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205276
85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276
88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019
Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205277
91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277
94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205278
96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278
---------------------------------------------------------------------------------------------------------------
Any help would be appreciated, thanks!
try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.
-
Hi all
First of all, I apologize if this is something that I can google. My knowledge of the administration of the network is all self-taught, so if there is a guide that I missed please point me in the right direction, it is often difficult to Google the terms for troubleshooting when your jargon is not the height.
The main problem is that when ping devices internal when you are connected to the results are very inconsistent.
Ping 192.168.15.102 with 32 bytes of data:
Reply from 192.168.15.102: bytes = 32 time = 112ms TTL = 128
Request timed out.
Request timed out.
Request timed out.
We have implemented an IPSec VPN connection to a remote Cisco ASA 5505. There is no connection problems, connection seems constant, etc. good packages. At this stage, I can only assume I have configuration problems, but I was watching this while if long and pair with my inexperience configuration of these settings I have no idea where to start. My first impressions are that LAN devices I'm ping do not send their response back or the ASA does not know how to route packets back?
Here is a dump of the configuration:
Output of the command: "show config".
: Saved
: Written by enable_15 to the 12:40:06.114 CDT MON Sep 9 2013
!
ASA Version 8.2 (5)
!
hostname VPN_Test
activate the encrypted password of D37rIydCZ/bnf1uj
2KFQnbNIdI.2KYOU encrypted passwd
names of
192.168.15.0 - internal network name
DDNS update method DDNS_Update
DDNS both
maximum interval 0 4 0 0
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
Description VLAN internal guests
nameif inside
security-level 100
DDNS update hostname 0.0.0.0
DDNS update DDNS_Update
DHCP client updated dns server time
192.168.15.1 IP address 255.255.255.0
!
interface Vlan2
Description of VLAN external to the internet
nameif outside
security-level 0
address IP xx.xx.xx.xx 255.255.255.248
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS server-group DefaultDNS
Server name 216.221.96.37
Name-Server 8.8.8.8
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
outside_access_in list extended access permit icmp any one
outside_access_in list extended access deny interface icmp outside interface inside
access extensive list ip 192.168.15.192 outside_access_in allow 255.255.255.192 all
Remote_splitTunnelAcl list standard allowed internal-network access 255.255.255.0
inside_nat0_outbound list extended access allowed internal-network ip, 255.255.255.0 192.168.15.192 255.255.255.192
Note to inside_access_in to access list blocking Internet traffic
access extensive list ip 192.168.15.192 inside_access_in allow 255.255.255.192 all
Note to inside_access_in to access list blocking Internet traffic
inside_access_in extended access list allow interface ip inside the interface inside
inside_access_in list of allowed ip extended access all 192.168.15.192 255.255.255.192
Note to inside_access_in to access list blocking Internet traffic
access extensive list ip 192.168.15.192 inside_nat0_outbound_1 allow 255.255.255.192 all
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.15.200 - 192.168.15.250 255.255.255.0 IP local pool VPN_IP_Pool
inside_access_ipv6_in list of access allowed IPv6 interface ip inside the interface inside
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow any response of echo outdoors
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 192.168.15.192 255.255.255.192
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
inside_access_ipv6_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 xx.xx.xx.xx 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
255.255.255.0 inside internal network http
http yy.yy.yy.yy 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection timewait
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.15.200 - 192.168.15.250 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.168.15.101 source inside
prefer NTP server 192.168.15.100 source inside
WebVPN
internal remote group strategy
Group remote attributes policy
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_splitTunnelAcl
username StockUser encrypted password privilege 0 t6a0Nv8HUfWtUdKz
username StockUser attributes
Strategy-Group-VPN remote
tunnel-group type remote access remotely
tunnel-group remote General attributes
address pool VPN_IP_Pool
Group Policy - by default-remote control
tunnel-group remote ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:f4271785b86e45dd3a17bab8f60cd2f3
Hi Graham,
My first question is do you have a site to site VPN and VPN remote access client.
After checking your configuration, I see you don't have any Site to SIte VPN configuration, so I'm assuming you ara facing issue with the VPN client.
And if I understand you are able to connect VPN client, but you not able to access internal resources properly.
I recommend tey and make the following changes.
First remove the following configuration:
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 192.168.15.192 255.255.255.192
You don't need the 1st one and I do not understand the reason for the second
Second, one is your pool IP subnet (192.168.15.200 - 192.168.15.250) and I don't know why you added this NAT.
If possible change your subnet pool all together because we do not recommend to use th ip POOL that is similar to your local network.
Try the changes described above and let me know in case if you have any problem.
Thank you
Jeet Kumar
-
Cisco VPN Client and Windows XP VPN Client IPSec to ASA
I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.
PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?
Config is:
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. 1 255.255.255.0
!
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0
flow-export destination inside-Bct 192.168.1.27 9996
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
NAT (inside-Bct) 0 access-list sheep-vpn
NAT (inside-Bct) 1 access list nat
NAT (inside-Bct) 2-nat-ganja access list
Access-group rdp on interface outside-Ganja
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
dynamic-access-policy-registration DfltAccessPolicy
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
life crypto ipsec security association seconds 214748364
Crypto ipsec kilobytes of life security-association 214748364
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
crypto isakmp identity address
ISAKMP crypto enable vpntest
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 30
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
No encryption isakmp nat-traversal
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.1.0 255.255.255.192 outside Baku
SSH 10.254.17.26 255.255.255.255 outside Baku
SSH 10.254.17.18 255.255.255.255 outside Baku
SSH 10.254.17.10 255.255.255.255 outside Baku
SSH 10.254.17.26 255.255.255.255 outside-Ganja
SSH 10.254.17.18 255.255.255.255 outside-Ganja
SSH 10.254.17.10 255.255.255.255 outside-Ganja
SSH 192.168.1.0 255.255.255.192 Interior-Bct
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
BCT.AZ value by default-field
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Hello
For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.
Please see configuration below:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml
or
Please see the section of tunnel-group config of the SAA.
There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.
So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.
Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.
"crypto isakmp nat-traversal.
Thirdly, change the transformation of the value
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
Let me know the result.
Thank you
Gilbert
-
Problems to connect via the Cisco VPN client IPSec of for RV180W small business router
Hello
I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for
> [34360] has no config mode. I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.
Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.
Router log file (I changed the IP
addresses > respectively as well as references to MAC addresses) Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart
> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT> [44074] because it is admitted only after the phase 1.
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [4500]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for> [4500] - > [44074] with spi = >.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP>
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP>
Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for> [4500] - > [44074] with spi = > The router configuration
IKE policy
VPN strategy
Client configuration
Hôte : < router="" ip=""> >
Authentication group name: remote.com
Password authentication of the Group: mysecretpassword
Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)
Username: myusername
Password: mypassword
Please contact Cisco.
Correct, the RV180 is not compatible with the Cisco VPN Client. The Iphone uses the Cisco VPN Client.
You can use the PPTP on the RV180 server to connect a PPTP Client.
In addition, it RV180 will allow an IPsec connection to third-party customers 3. Greenbow and Shrew Soft are 2 commonly used clients.
-
ASA allows 1 only RAS VPN Client IPSEC
Hi all
I have a strange problem where an ASA 5510 configured for IPSEC - over - udp VPN RAS allows only one 1 customer vpn traffic through.
Other clients can connect successfully (obtain IP/DNS etc., auth using LDAP) but only the all connected client is first able to browse internal resources. Others show 0 decrypted packets when I check the statistics. I have confirmed that it is not a problem with the license that the ipsec default license allows customers up to 250 I believe. Does anyone had this problem in the past?
TKS,
Donavan
It is usually a problem with the translations, which intervened on the NAT/PAT device in front of these multiple machines:
http://www.ciscotaccc.com/Kaidara-Advisor/security/showcase?case=K71102938
Check the translations look correct initially on this device. There should be a translation for each VPN.
There were also a few bugs on multiple clients behind the same PAT, such as CSCse03299, but these had to do with IPSec over TCP connections.
-heather
-
Layman to ASA 5505 vpn of the native vpn client internet, tcp 1723
Hi all
I am setting up this asa for connect users at home to my network using vpn clients from microsoft to the native address with windows xp on the internet.
This asa have, on the outside interface an ip public Internet and inside Board have set up in the network of 192.168.0.x and I want to access this network of internet users using native vpn clients.
I tested with a pc connected directly to the external interface and works well, but when I connect this interface to the internet and tried to connect to the vpn user I can see it in the newspapers and unable to connect with error 800.
Request TCP and eliminated from "public_ip_client/61648" outdoors: publicip_outside_interface / 1723 "
Can help me please?, very thanks in advance!
(running configuration)
: Saved
:
ASA Version 8.4 (3)
!
ciscoasa hostname
activate the password * encrypted
passwd * encrypted
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address publicinternetaddress 255.255.255.0
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network gatewayono object
Home gatewayofinternetprovideraccess
Description salida gateway ono
service remotointerno object
service destination tcp 3389 eq
Remote description
network pb_clienteing_2 object
host 192.168.0.15
Description Pebble client food bowl 2
service remotoexternopebble object
Service tcp destination eq 5353
Description remotoexterno
network actusmon object
Home 192.168.0.174
Description web news monitor
the Web object service
Service tcp destination eq www
Description 80
irdeto network object
Home 192.168.0.31
Irdeto description
network nmx_mc_p object
host 192.168.0.60
Main description of NMX multichannel
network nmx_mc_r object
Home 192.168.0.61
Description NMX multichannel reserva
network tarsys object
host 192.168.0.10
Tarsys description
network nmx_teuve object
host 192.168.0.30
Nmx cabecera teuve description
tektronix network object
host 192.168.0.20
Tektronix vnc description
vnc service object
destination eq 5900 tcp service
Description access vnc
service exvncnmxmcr object
Service tcp destination EQ. 5757
Access vnc external nmx mc figurative description
service exvncirdeto object
Service tcp destination eq 6531
Description access vnc external irdeto
service exvncnmxmcp object
Service tcp destination eq 5656
service exvnctektronix object
Service tcp destination eq 6565
service exvncnmxteuve object
Service tcp destination eq 6530
ssh service object
tcp destination eq ssh service
service sshtedialexterno object
Service tcp destination eq 5454
puertosabiertos tcp service object-group
Remotedesktop description
EQ port 3389 object
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
the DM_INLINE_NETWORK_1 object-group network
network-object object irdeto
network-object object nmx_mc_p
network-object object nmx_mc_r
network-object object nmx_teuve
tektronix network-object
object-group service udp vpn
EQ port 1723 object
DM_INLINE_TCP_1 tcp service object-group
EQ object of the https port
EQ pptp Port object
the DM_INLINE_NETWORK_2 object-group network
network-object object actusmon
network-object object tarsys
inside_access_in remotointerno permitted object extended access list a whole
inside_access_in list extended access allowed object ssh a whole
inside_access_in list extended access allowed object-group TCPUDP any any eq www
inside_access_in list extended access permit icmp any one
inside_access_in list extended access allowed object vnc a whole
inside_access_in of access allowed any ip an extended list
outside_access_in list extended access allowed object remotointerno any object pb_clienteing_2
outside_access_in list extended access allowed object-group TCPUDP any object actusmon eq www
access-list outside_access_in note Acceso tedial ssh
outside_access_in list extended access permit tcp any object tarsys eq ssh
outside_access_in list extended access allowed object vnc any object-group DM_INLINE_NETWORK_1
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_access_in list extended access deny icmp a whole
access-list standard corporate allowed 192.168.0.0 255.255.255.0
Split-Tunnel-ACL access-list allowed standard 192.168.0.0 255.255.255.0
pager lines 24
Enable logging
monitor debug logging
logging of debug asdm
Debugging trace record
Within 1500 MTU
Outside 1500 MTU
IP local pool 192.168.0.100 - 192.168.0.110 mask 255.255.255.0 clientesvpn
IP local pool clientesvpn2 192.168.1.120 - 192.168.1.130 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT (exterior, Interior) static source any service of actusmon of interface static destination Web one-way Web interface
NAT (exterior, Interior) static source to any destination interface interface static tarsys one-way sshtedialexterno ssh service
NAT (exterior, Interior) static source any destination interface interface static one-way pb_clienteing_2 service remotoexternopebble remotointerno
NAT (exterior, Interior) static source any destination interface interface static irdeto one-way exvncirdeto vnc service
NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxmcp service nmx_mc_p
NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxmcr service nmx_mc_r
NAT (exterior, Interior) static source any destination interface interface static one-way vnc exvncnmxteuve service nmx_teuve
NAT (exterior, Interior) static source any destination interface interface static tektronix one-way exvnctektronix vnc service
NAT (all, outside) interface dynamic source DM_INLINE_NETWORK_2
inside_access_in access to the interface inside group
Access-group outside_access_in in interface out by-user-override
Route outside 0.0.0.0 0.0.0.0 gatewayinternetprovideracces 1
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
EOU allow none
local AAA authentication attempts 10 max in case of failure
Enable http server
http 192.168.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
No vpn sysopt connection permit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 clientewindowsxp
IKEv1 crypto ipsec transform-set clientewindowsxp transport mode
Crypto ipsec transform-set ikev1 L2TP-IKE1-Transform-Set esp - aes esp-sha-hmac
Crypto ipsec ikev1 transit mode L2TP-IKE1-Transform-Set transform-set
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 1 set transform-set clientewindowsxp ikev1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 1jeu ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Crypto-map dynamic L2TP - map 10 set transform-set L2TP-IKE1-Transform-Set ikev1
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Crypto map L2TP - VPN - dynamic 20-isakmp ipsec L2TP-map map
L2TP-VPN-card interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
trustpoint to ikev2 crypto Ingeniería remote access
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 192.168.0.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd dns 8.8.8.8
dhcpd outside auto_config
!
dhcpd address 192.168.0.5 - 192.168.0.36 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd allow inside
!
no basic threat threat detection
no statistical access list - a threat detection
no statistical threat detection tcp-interception
SSL-trust Ingeniería out point
WebVPN
tunnel-group-list activate
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
WINS server no
Server 192.168.0.1 DNS value
Protocol-tunnel-VPN l2tp ipsec
by default no
attributes of Group Policy DfltGrpPolicy
value of server DNS 8.8.8.8
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
internal engineering group policy
attributes of Ingeniería group policy
Protocol-tunnel-VPN l2tp ipsec
by default no
L2TP-policy group policy interns
attributes of L2TP-policy-group policy
value of server DNS 8.8.8.8
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value Split-Tunnel-ACL
Intercept-dhcp enable
username, password Ingeniería 4fD/5xY/6BwlkjGqMZbnKw is encrypted nt privilege 0
Ingeniería username attributes
VPN-group-policy Ingeniería
password rjuve SjBNOLNgSkUi5KWk/TUsTQ user name is nt encrypted
attributes global-tunnel-group DefaultRAGroup
address clientesvpn pool
address clientesvpn2 pool
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
Group Policy - by default-L2TP-policy
authorization required
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
ms-chap-v2 authentication
!
class-map inspection_default
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
!
context of prompt hostname
anonymous reporting remote call
Cryptochecksum:59b54f1d10fe829aeb47bafee57ba95e
: end
don't allow no asdm history
I ramon I guess that service policy is not applied in the firewall. So it does not not trust other than the same audience segment.
Apply like this.
global_policy global service policy.
because according to the configs old, I see that the policy has not been applied. Please let me know the results.
Please rate if the given info can help.
-
Problem setting out by ASA 5505 VPN
While inside a network secured by an ASA 5505, I can't establish a PPTP VPN on. The ASA will connect the following:
09-2009 20:50:09 creating 305006 24.13.209.125 regular translation failed for the internal protocol 47 src: 192.168.132.108 dst outside:xxx.xxx.xxx.125
I looked at the msg of error in line, but for some reason, I'm just not understand what he says. How can I fix it? Let me know if you have any questions... Thank you guys!
Colombia-British
Hello
Enable pptp inspection
pixfirewall (config) #policy - map global_policy
pixfirewall(config-pmap) #class inspection_default
pixfirewall (config-pmap-c) #inspect pptp
Go to this link for the use of pptp/gre info background detail under various codes.
Concerning
-
ASA 5505 VPN established, cannot access inside the network
Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.
After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.
Here is my config:
ASA Version 8.2 (5)
!
hostname asa01
domain kevinasa01.net
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 5
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan5
No nameif
security-level 50
IP 172.16.1.1 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain kevinasa01.net
permit same-security-traffic intra-interface
Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (outside) 1 192.168.254.0 255.255.255.0
NAT (inside) 0 access-list sheep - in
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal Remote_Kevin group strategy
attributes of Group Policy Remote_Kevin
value of server DNS 192.168.1.12 192.168.1.13
VPN - connections 3
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
kevinasa01.NET value by default-field
username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
username kevin attributes
VPN-group-policy Remote_Kevin
type tunnel-group Remote_Kevin remote access
attributes global-tunnel-group Remote_Kevin
address-pool
Group Policy - by default-Remote_Kevin
IPSec-attributes tunnel-group Remote_Kevin
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
: endThank you
Hello
I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.
I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.
The acl must be:
sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
For nat (inside), you have 2 lines:
NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
NAT (inside) 1 0.0.0.0 0.0.0.0Why are you doing this nat (outside)?
NAT (outside) 1 192.168.254.0 255.255.255.0
Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)
Thank you.
PS: Please do not forget to rate and score as good response if this solves your problem.
-
Ikev1 ASA 5505 VPN connection error
Hello
I had previously defined our VPN using IPsec on our ASA 5505 via the ASDM. It was workign fine until an outtage power loses my settings on the device. (possibly a recording of order is not pressed)
Now when I try and put in place, once again I am recieveing an error to port binding. I have configured as normal using the wizard and activate split defintion and exempt the network inside.
The isssue when you apply the settings that I get is:
"[ERROR] crypto ikev 1 activate outdoors.
IkevReceiverInit, cannot bind the port. "
When I try to connect to the VPN I then get an error "the server cannot be reached" or something similar to that...
Could someone please shed some light on what can cause this problem?
Best regards, the Paris
William.
Hello
Thanks for the information!
We will need to know why this host using UDP 4500 and if this host really needs to use this port.
What type of application is running on this host?
What is a host internal or external?
You may also block the host on the SAA on the incoming interface to avoid the use of the UDP 4500 port using a group of access (outside or inside). Don't forget that you will need a ip to allow a at the end of the ACL to avoid any problems. Another option would be to use IKEv1/IPsec over TCP
IKEv1/IPsec over TCP allows a Cisco VPN client operate in an environment in which IKEv1 or standard ESP may not work or may work only with the change of the existing firewall rules. IPsec over TCP encapsulates IPsec protocols both IKEv1 in a TCP packet as and allows a tunnel secure two firewalls and NAT and PAT devices. This feature is disabled by default.
The default port is 10000.
HostName (config) # ikev1 crypto ipsec-over-tcp
You also need to activate on the VPN client under the profile.
Change > Transport > IPSec over TCP.
I hope this helps.
Luis.
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
On ASA 5505 VPN cannot access remote (LAN)
I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.
Tyler
Just remove the line of nat (outside) and ACL outside_nat0_outbound.
And talk about these statements:
IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).
2, crypto isakmp nat traversal 10 or 20
3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.
4, create the other ACL (ST) with different name and source and destination like no nat ACL.
5, then type nat (inside) 0 access-list sheep
6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).
Concerning
Maybe you are looking for
-
Metal Gear Solid 2 - not playable for win 7, even when it runs on older versions of win
Hi all. rather disappointed by what the hype of 7, shame MS didn't ' t ask a player to watch it before you release it to the public instead of ask clerks office and women of the House... Metal gear solid 2. for loads of PC Run/menu options. After th
-
Photosmart C309a: The printer does not print
I am trying to print and it looks like it will print but blank paper comes out. I have all new ink cartridges. I tried to replace the cartridges, turn the machine and even unplugged. Any suggestion will be appreciated.
-
Computer with the best care runs slower with the same VI
We just build new computers to run our labview acquisition program. However, the new computers are running much slower than the 'old' software. The new computers are Intel (Core i7) clocked at 2.66 GHz with 2 GB of DDR3 1333 MHz ram, while old comput
-
I used it just four days ago. Now I can't find it at the usual location in Help and support. You know, I don't know of one. One where you send notifications to HP that you want to chat with a technician who can help you with a computer problem? They
-
Smartphone Youtube blackBerry error
I get an error when you try to watch videos on Youtube. the error is " the returned page had no content type and therefore can not be read. I am able to front page normally, I get this error when you try to view the videos. What should I do?