Layman to ASA 5505 vpn of the native vpn client internet, tcp 1723

Similar Questions

• LAN ASA 5505 VPN client access issue

  Hello

  I'm no expert in ASA and routing so I ask support the following case.

  There is a (running on Windows 7) Cisco VPN client and an ASA5505.

  The objectives are client can use the gateway remote on SAA for Skype and able to access devices in SAA within the interface.

  The Skype works well, but I can't access devices in the interface inside through a VPN connection.

  Can you please check my following config and give me any advice to fix NAT or VPN settings?

  ASA Version 7.2 (4)

  !

  ciscoasa hostname

  domain default.domain.invalid

  activate wDnglsHo3Tm87.tM encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface Vlan3

  prior to interface Vlan1

  nameif dmz

  security-level 50

  no ip address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain default.domain.invalid

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 any

  outside_access_in list of allowed ip extended access entire 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  local pool VPNPOOL 10.0.0.200 - 10.0.0.220 255.255.255.0 IP mask

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 524.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 1 10.0.0.0 255.255.255.0

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (outside) 1 10.0.0.0 255.255.255.0

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map pfs set 20 Group1

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd dns xx.xx.xx.xx interface inside

  dhcpd allow inside

  !

  attributes of Group Policy DfltGrpPolicy

  No banner

  WINS server no

  value of server DNS 84.2.44.1

  DHCP-network-scope no

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  Group-lock no

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  by default no

  Split-dns no

  Disable dhcp Intercept 255.255.255.255

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout 30

  disable the IP-phone-bypass

  disable the leap-bypass

  allow to NEM

  Dungeon-client-config backup servers

  MSIE proxy server no

  MSIE-proxy method non - change

  Internet Explorer proxy except list - no

  Disable Internet Explorer-proxy local-bypass

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  address pools no

  enable Smartcard-Removal-disconnect

  the firewall client no

  rule of access-client-none

  WebVPN

  url-entry functions

  HTML-content-filter none

  Home page no

  4 Keep-alive-ignore

  gzip http-comp

  no filter

  list of URLS no

  value of customization DfltCustomization

  port - forward, no

  port-forward-name value access to applications

  SSO-Server no

  value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

  SVC no

  SVC Dungeon-Installer installed

  SVC keepalive no

  generate a new key SVC time no

  method to generate a new key of SVC no

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  deflate compression of SVC

  internal group XXXXXX strategy

  attributes of XXXXXX group policy

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  XXXXXX G910DDfbV7mNprdR encrypted privilege 15 password username

  username password encrypted XXXXXX privilege 0 5p9CbIe7WdF8GZF8

  attributes of username XXXXXX

  Strategy Group-VPN-XXXXXX

  username privilege 15 encrypted password cRQbJhC92XjdFQvb XXXXX

  tunnel-group XXXXXX type ipsec-ra

  attributes global-tunnel-group XXXXXX

  address VPNPOOL pool

  Group Policy - by default-XXXXXX

  tunnel-group ipsec-attributes XXXXXX

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23

  : end

  ciscoasa #.

  Thanks in advance!

  fbela

  config #no nat (inside) 1 10.0.0.0 255.255.255.0< this="" is="" not="">

  Add - config #same-Security-permit intra-interface

  #access - extended list allowed sheep ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  #nat (inside) 0 access-list sheep

  Please add and test it.

  Thank you

  Ajay

• ASA 5505 VPN Client Ipsec config problems

  I configured the asa the wizard to Setup vpn, but this still does not work properly. Vpn connect without problem, but I can't access all the resources on the 192.168.1.x subnet. Don't know what I'm missing here, here's a copy of my config.

  ASA Version 8.0 (3)
  !
  host name
  domain name
  activate the password
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.1.3 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  "Public ip" 255.255.255.0 IP address
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passwd
  passive FTP mode
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  Server name 192.168.1.28
  domain fmrs.org
  GroupVpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  vpngroup_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  outside_access_in list extended access permit tcp any any eq pptp
  outside_access_in list extended access will permit a full
  inside_nat0_outbound list of allowed ip extended access all 192.168.99.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  inside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 any
  access extensive list ip 192.168.99.0 inside_access_in allow 255.255.255.0 any
  inside_access_in list of allowed ip extended access all 192.168.99.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask 192.168.99.2 - 192.168.99.100 255.255.255.0 IP local pool GroupPool
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 602.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 192.168.1.0 255.255.255.0
  public static tcp (indoor, outdoor) interface 192.168.1.62 pptp pptp netmask 255.255.255.255
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 66.76.199.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server fmrsdc
  fmrsdc AAA-server 192.168.1.28
  Timeout 5
  fmrsasa key
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow inside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  No vpn-addr-assign aaa
  No dhcp vpn-addr-assign
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  GroupVpn internal group policy
  GroupVpn group policy attributes
  value of server WINS 192.168.1.28
  value of server DNS 192.168.1.28
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list GroupVpn_splitTunnelAcl
  FMRs.org value by default-field
  ID password cisco
  tunnel-group GroupVpn type remote access
  attributes global-tunnel-group GroupVpn
  address pool GroupPool
  authentication-server-group fmrsdc
  Group Policy - by default-GroupVpn
  IPSec-attributes tunnel-group GroupVpn
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  inspect the pptp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:b5df903e690566360b38735b6d79e65e
  : end

  Please configure the following:

  ISAKMP nat-traversal crypto

  management-access inside

  You should be able to ping of the SAA within the IP 192.168.1.3

• ASA 5505 VPN sessions maximum 25?

  Hello friend´s

  The company I work when acquired several ASA 5505, so now we will be able to connect several branches at Headquarters. But, now, I know that the ASA 5505 just scalates to 25 VPN sessions, I think that it won´t be enough to support the operations of an office. I have a lot of questions about this:

  Is - what the number 25 menas supporting up to 25 L2L tunnels? Or it means 25 sessions, regardless of the amount of L2L tunnels?

  Is this the way number 25 supporting up to 25 users in the Branch Office? Or it means that a user can use several sessions?

  I'm the stage of testing in a laboratory where one PC connects to many applications, at - it now someone if there is a command in the SAA to check how many VPN sessions is used?

  Please, do not hesitate to ask as much as necessary information. Any comments or document will be appreciated.

  Kind regards!

  Hi Alex,

  The assistance session 25 ASA 5505 VPN as max for IKEv1 or IPSEC tunnels customers it could be up to 25 L2L tunnels or 25 users using ikev1 (Legacy IPSEC client) and another 25 sessions for Anyconnect or Webvpn in this case are used in function.

  To check how many sessions VPN is currently running, run the command 'Show vpn-sessiondb' and 'display the summary vpn-sessiondb '.

  Find the official documentation for the ASA5505 on the following link:

  http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-series-next-generation-firewalls/datasheet-C78-733510.html

  Rate if helps.

  -Randy-

• No Internet connectivity with ASA 5505 VPN remote access

  Hello

  I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?

  Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.

  Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?

  I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.

  Thank you very much for you help.

  Concerning

  Salman

  Salman

  What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.

  You have at least 2 options:

  -You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.

  -You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command

  permit same-security-traffic intra-interface

  HTH

  Rick

• ASA 5505 VPN established, cannot access inside the network

  Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.

  After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.

  Here is my config:

  ASA Version 8.2 (5)
  !
  hostname asa01
  domain kevinasa01.net
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  switchport access vlan 5
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan5
  No nameif
  security-level 50
  IP 172.16.1.1 255.255.255.0
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain kevinasa01.net
  permit same-security-traffic intra-interface
  Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
  access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
  access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (outside) 1 192.168.254.0 255.255.255.0
  NAT (inside) 0 access-list sheep - in
  NAT (inside) 1 192.168.1.0 255.255.255.0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal Remote_Kevin group strategy
  attributes of Group Policy Remote_Kevin
  value of server DNS 192.168.1.12 192.168.1.13
  VPN - connections 3
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
  kevinasa01.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy Remote_Kevin
  type tunnel-group Remote_Kevin remote access
  attributes global-tunnel-group Remote_Kevin
  address-pool
  Group Policy - by default-Remote_Kevin
  IPSec-attributes tunnel-group Remote_Kevin
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
  : end

  Thank you

  Hello

  I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.

  I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.

  The acl must be:

  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0

  For nat (inside), you have 2 lines:

  NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Why are you doing this nat (outside)?

  NAT (outside) 1 192.168.254.0 255.255.255.0

  Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)

  Thank you.

  PS: Please do not forget to rate and score as good response if this solves your problem.

• ASA 5505 VPN cannot access inside the host

  I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.

  framework for configuration below

  interface Vlan1

  nameif inside

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Crypto-map dynamic inside_dyn_map 20 set pfs

  Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map

  inside crypto map inside_map interface

  crypto ISAKMP allow inside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  global service-policy global_policy

  XXXXXXX strategy of Group internal

  attributes of the strategy group xxxxxxx

  banner value xxxxx Site Recovery

  WINS server no

  24.xxx.xxx.xx value of DNS server

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  by default no

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout no

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  the address value xxxxxx pools

  enable Smartcard-Removal-disconnect

  the firewall client no

  WebVPN

  url-entry functions

  Free VPN of CNA no

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  tunnel-group xxxx type ipsec-ra

  tunnel-group xxxx general attributes

  xxxx address pool

  Group Policy - by default-xxxx

  blountdr group of tunnel ipsec-attributes

  pre-shared-key *.

  Missing nat exemption for vpn clients. Add the following and you should be good to go.

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

• ASA 5505 VPN works great but can't access internet via the tunnel to customers

  We have an ASA 5505 ASA 8.2.1 running and using IPSec for Remote access clients in the main office.  Remote access is a lot of work, with full access to network resources in the main office and the only thing I can't get to work is access to internet through the tunnel.  I don't want to use split tunneling.  I use ASDM 6.2.1 for configuration.  Any help is appreciated.  I'm probably missing something simple and it looked so much, I'm probably looking at right beyond the error.  Thanks in advance for your time and help!    Jim

  Add a statement of nat for your segment of customer on the external interface

  NAT (outside) - access list

  then allow traffic routing back on the same interface, it is entered in the

  permit same-security-traffic intra-interface

  *

  *

  * more than information can be found here:

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807...

  On Wednesday, 27 January 2010, at 23:12, jimcanova

• Cisco ASA 5505 VPN Site to Site

  Hi all

  First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..

  I'd appreciate any help that can be directed to this problem please.  Slowly losing my mind

  Please see details below:

  Two ADMS are 7.1

  IOS

  ASA 1

  Nadia

  :

  ASA Version 9.0 (1)

  !

  hostname PAYBACK

  activate the encrypted password of HSMurh79NVmatjY0

  volatile xlate deny tcp any4 any4

  volatile xlate deny tcp any4 any6

  volatile xlate deny tcp any6 any4

  volatile xlate deny tcp any6 any6

  volatile xlate deny udp any4 any4 eq field

  volatile xlate deny udp any4 any6 eq field

  volatile xlate deny udp any6 any4 eq field

  volatile xlate deny udp any6 any6 eq field

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask

  !

  interface Ethernet0/0

  switchport access vlan 2

  Speed 100

  full duplex

  !

  interface Ethernet0/1

  link Trunk Description of SW1

  switchport trunk allowed vlan 1,10,20,30,40

  switchport trunk vlan 1 native

  switchport mode trunk

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  No nameif

  no level of security

  no ip address

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 92.51.193.158 255.255.255.252

  !

  interface Vlan10

  nameif inside

  security-level 100

  IP 192.168.10.1 255.255.255.0

  !

  interface Vlan20

  nameif servers

  security-level 100

  address 192.168.20.1 255.255.255.0

  !

  Vlan30 interface

  nameif printers

  security-level 100

  192.168.30.1 IP address 255.255.255.0

  !

  interface Vlan40

  nameif wireless

  security-level 100

  192.168.40.1 IP address 255.255.255.0

  !

  connection line banner welcome to the Payback loyalty systems

  boot system Disk0: / asa901 - k8.bin

  passive FTP mode

  summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00

  DNS domain-lookup outside

  DNS lookup field inside

  domain-lookup DNS servers

  DNS lookup domain printers

  DNS domain-lookup wireless

  DNS server-group DefaultDNS

  Server name 83.147.160.2

  Server name 83.147.160.130

  permit same-security-traffic inter-interface

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  ftp_server network object

  network of the Internal_Report_Server object

  Home 192.168.20.21

  Description address internal automated report server

  network of the Report_Server object

  Home 89.234.126.9

  Description of server automated reports

  service object RDP

  service destination tcp 3389 eq

  Description RDP to the server

  network of the Host_QA_Server object

  Home 89.234.126.10

  Description QA host external address

  network of the Internal_Host_QA object

  Home 192.168.20.22

  host of computer virtual Description for QA

  network of the Internal_QA_Web_Server object

  Home 192.168.20.23

  Description Web Server in the QA environment

  network of the Web_Server_QA_VM object

  Home 89.234.126.11

  Server Web Description in the QA environment

  service object SQL_Server

  destination eq 1433 tcp service

  network of the Demo_Server object

  Home 89.234.126.12

  Description server set up for the product demo

  network of the Internal_Demo_Server object

  Home 192.168.20.24

  Internal description of the demo server IP address

  network of the NETWORK_OBJ_192.168.20.0_24 object

  subnet 192.168.20.0 255.255.255.0

  network of the NETWORK_OBJ_192.168.50.0_26 object

  255.255.255.192 subnet 192.168.50.0

  network of the NETWORK_OBJ_192.168.0.0_16 object

  Subnet 192.168.0.0 255.255.0.0

  service object MSSQL

  destination eq 1434 tcp service

  MSSQL port description

  VPN network object

  192.168.50.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.50.0_24 object

  192.168.50.0 subnet 255.255.255.0

  service object TS

  tcp destination eq 4400 service

  service of the TS_Return object

  tcp source eq 4400 service

  network of the External_QA_3 object

  Home 89.234.126.13

  network of the Internal_QA_3 object

  Home 192.168.20.25

  network of the Dev_WebServer object

  Home 192.168.20.27

  network of the External_Dev_Web object

  Home 89.234.126.14

  network of the CIX_Subnet object

  255.255.255.0 subnet 192.168.100.0

  network of the NETWORK_OBJ_192.168.10.0_24 object

  192.168.10.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_84.39.233.50 object

  Home 84.39.233.50

  network of the NETWORK_OBJ_92.51.193.158 object

  Home 92.51.193.158

  network of the NETWORK_OBJ_192.168.100.0_24 object

  255.255.255.0 subnet 192.168.100.0

  network of the NETWORK_OBJ_192.168.1.0_24 object

  subnet 192.168.1.0 255.255.255.0

  object-group service DM_INLINE_SERVICE_1

  the tcp destination eq ftp service object

  the purpose of the tcp destination eq netbios-ssn service

  the purpose of the tcp destination eq smtp service

  service-object TS

  the Payback_Internal object-group network

  object-network 192.168.10.0 255.255.255.0

  object-network 192.168.20.0 255.255.255.0

  object-network 192.168.40.0 255.255.255.0

  object-group service DM_INLINE_SERVICE_3

  the purpose of the service tcp destination eq www

  the purpose of the tcp destination eq https service

  service-object TS

  service-object, object TS_Return

  object-group service DM_INLINE_SERVICE_4

  service-object RDP

  the purpose of the service tcp destination eq www

  the purpose of the tcp destination eq https service

  object-group service DM_INLINE_SERVICE_5

  purpose purpose of the MSSQL service

  service-object RDP

  service-object TS

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group service DM_INLINE_SERVICE_6

  service-object TS

  service-object, object TS_Return

  the purpose of the service tcp destination eq www

  the purpose of the tcp destination eq https service

  Note to outside_access_in to access list that this rule allows Internet the interal server.

  Notice on the outside_access_in of the access-list allowed:

  Comment from outside_access_in-list of FTP access

  Comment from outside_access_in-RDP access list

  Comment from outside_access_in-list of SMTP access

  Note to outside_access_in to access list Net Bios

  Comment from outside_access_in-SQL access list

  Comment from outside_access_in-list to access TS - 4400

  outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server

  access host access-list outside_access_in note rule internal QA

  Notice on the outside_access_in of the access-list allowed:

  Comment from outside_access_in-HTTP access list

  Comment from outside_access_in-RDP access list

  outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www

  Notice on the outside_access_in of the access-list access to the internal Web server:

  Notice on the outside_access_in of the access-list allowed:

  Comment from outside_access_in-HTTP access list

  Comment from outside_access_in-RDP access list

  outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server

  Note to outside_access_in to access list rule allowing access to the demo server

  Notice on the outside_access_in of the access-list allowed:

  Comment from outside_access_in-RDP access list

  Comment from outside_access_in-list to access MSSQL

  outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server

  outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3

  Note to outside_access_in access to the development Web server access list

  outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer

  AnyConnect_Client_Local_Print deny any4 any4 ip extended access list

  AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137

  AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns

  Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0

  permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0

  pager lines 24

  Enable logging

  information recording console

  asdm of logging of information

  address record

  [email protected] / * /.

  the journaling recipient

  [email protected] / * /.

  level alerts

  Outside 1500 MTU

  Within 1500 MTU

  MTU 1500 servers

  MTU 1500 printers

  MTU 1500 wireless

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-711 - 52.bin

  don't allow no asdm history

  ARP timeout 14400

  no permit-nonconnected arp

  NAT (inside, outside) source Dynamics one interface

  NAT (wireless, outdoors) source Dynamics one interface

  NAT (servers, outside) no matter what source dynamic interface

  NAT (servers, external) static source Internal_Report_Server Report_Server

  NAT (servers, external) static source Internal_Host_QA Host_QA_Server

  NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM

  NAT (servers, external) static source Internal_Demo_Server Demo_Server

  NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

  NAT (servers, external) static source Internal_QA_3 External_QA_3

  NAT (servers, external) static source Dev_WebServer External_Dev_Web

  NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.10.0 255.255.255.0 inside
  http 192.168.40.0 255.255.255.0 wireless
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set pfs
  peer set card crypto outside_map 1 84.39.233.50
  card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map interface card crypto outside
  trustpool crypto ca policy
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 5
  FRP sha
  second life 86400
  Crypto ikev2 activate out of service the customer port 443
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 77.75.100.208 255.255.255.240 outside
  SSH 192.168.10.0 255.255.255.0 inside
  SSH 192.168.40.0 255.255.255.0 wireless
  SSH timeout 5
  Console timeout 0

  dhcpd 192.168.0.1 dns
  dhcpd outside auto_config
  !
  dhcpd address 192.168.10.21 - 192.168.10.240 inside
  dhcpd dns 192.168.20.21 83.147.160.2 interface inside
  paybackloyalty.com dhcpd option 15 inside ascii interface
  dhcpd allow inside
  !
  dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
  dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
  dhcpd update dns of the wireless interface
  dhcpd option 15 ascii paybackloyalty.com wireless interface
  dhcpd activate wireless
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  internal Payback_VPN group strategy
  attributes of Group Policy Payback_VPN
  VPN - 10 concurrent connections
  Ikev1 VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
  attributes of Group Policy DfltGrpPolicy
  value of 83.147.160.2 DNS server 83.147.160.130
  VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
  internal GroupPolicy_84.39.233.50 group strategy
  attributes of Group Policy GroupPolicy_84.39.233.50
  VPN-tunnel-Protocol ikev1, ikev2
  Noelle XB/IpvYaATP.2QYm username encrypted password
  Noelle username attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
  Éanna attributes username
  VPN-group-policy Payback_VPN
  type of remote access service
  Michael qpbleUqUEchRrgQX of encrypted password username
  user name Michael attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
  user name Danny attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
  user name Aileen attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
  Aidan username attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
  shane.c iqGMoWOnfO6YKXbw encrypted password username
  username shane.c attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  Shane uYePLcrFadO9pBZx of encrypted password username
  user name Shane attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  username, encrypted James TdYPv1pvld/hPM0d password
  user name James attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  Mark yruxpddqfyNb.qFn of encrypted password username
  user name brand attributes
  type of service admin
  username password of Mary XND5FTEiyu1L1zFD encrypted
  user name Mary attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
  Massimo username attributes
  VPN-group-policy Payback_VPN
  type of remote access service
  type tunnel-group Payback_VPN remote access
  attributes global-tunnel-group Payback_VPN
  VPN1 address pool
  Group Policy - by default-Payback_VPN
  IPSec-attributes tunnel-group Payback_VPN
  IKEv1 pre-shared-key *.
  tunnel-group 84.39.233.50 type ipsec-l2l
  tunnel-group 84.39.233.50 General-attributes
  Group - default policy - GroupPolicy_84.39.233.50
  IPSec-attributes tunnel-group 84.39.233.50
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  Global class-card class
  match default-inspection-traffic
  !
  !
  World-Policy policy-map
  Global category
  inspect the dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the pptp
  inspect the rsh
  inspect the rtsp
  inspect the sip
  inspect the snmp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect xdmcp
  inspect the icmp error
  inspect the icmp
  !
  service-policy-international policy global
  192.168.20.21 SMTP server
  context of prompt hostname
  no remote anonymous reporting call
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1

  ASA 2

  ASA Version 9.0 (1)

  !

  Payback-CIX hostname

  activate the encrypted password of HSMurh79NVmatjY0

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  Speed 100

  full duplex

  !

  interface Ethernet0/1

  Description this port connects to the local network VIRTUAL 100

  switchport access vlan 100

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  switchport access vlan 100

  !

  interface Ethernet0/4

  switchport access vlan 100

  !

  interface Ethernet0/5

  switchport access vlan 100

  !

  interface Ethernet0/6

  switchport access vlan 100

  !

  interface Ethernet0/7

  switchport access vlan 100

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 84.39.233.50 255.255.255.240

  !

  interface Vlan100

  nameif inside

  security-level 100

  IP 192.168.100.1 address 255.255.255.0

  !

  banner welcome to Payback loyalty - CIX connection line

  passive FTP mode

  summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00

  DNS domain-lookup outside

  DNS lookup field inside

  DNS server-group defaultDNS

  Name-Server 8.8.8.8

  Server name 8.8.4.4

  permit same-security-traffic inter-interface

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  network of the host-CIX-1 object

  host 192.168.100.2

  Description This is the VM server host machine

  network object host-External_CIX-1

  Home 84.39.233.51

  Description This is the external IP address of the server the server VM host

  service object RDP

  source between 1-65535 destination eq 3389 tcp service

  network of the Payback_Office object

  Home 92.51.193.158

  service object MSQL

  destination eq 1433 tcp service

  network of the Development_OLTP object

  Home 192.168.100.10

  Description for Eiresoft VM

  network of the External_Development_OLTP object

  Home 84.39.233.52

  Description This is the external IP address for the virtual machine for Eiresoft

  network of the Eiresoft object

  Home 146.66.160.70

  Contractor s/n description

  network of the External_TMC_Web object

  Home 84.39.233.53

  Description Public address to the TMC Web server

  network of the TMC_Webserver object

  Home 192.168.100.19

  Internal description address TMC Webserver

  network of the External_TMC_OLTP object

  Home 84.39.233.54

  External targets OLTP IP description

  network of the TMC_OLTP object

  Home 192.168.100.18

  description of the interal target IP address

  network of the External_OLTP_Failover object

  Home 84.39.233.55

  IP failover of the OLTP Public description

  network of the OLTP_Failover object

  Home 192.168.100.60

  Server failover OLTP description

  network of the servers object

  subnet 192.168.20.0 255.255.255.0

  being Wired network

  192.168.10.0 subnet 255.255.255.0

  the subject wireless network

  192.168.40.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.100.0_24 object

  255.255.255.0 subnet 192.168.100.0

  network of the NETWORK_OBJ_192.168.10.0_24 object

  192.168.10.0 subnet 255.255.255.0

  network of the Eiresoft_2nd object

  Home 137.117.217.29

  Description 2nd Eiresoft IP

  network of the Dev_Test_Webserver object

  Home 192.168.100.12

  Description address internal to the Test Server Web Dev

  network of the External_Dev_Test_Webserver object

  Home 84.39.233.56

  Description This is the PB Dev Test Webserver

  network of the NETWORK_OBJ_192.168.1.0_24 object

  subnet 192.168.1.0 255.255.255.0

  object-group service DM_INLINE_SERVICE_1

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_2

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_3

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_4

  service-object MSQL

  service-object RDP

  the tcp destination eq ftp service object

  object-group service DM_INLINE_SERVICE_5

  service-object MSQL

  service-object RDP

  the tcp destination eq ftp service object

  object-group service DM_INLINE_SERVICE_6

  service-object MSQL

  service-object RDP

  the Payback_Intrernal object-group network

  object-network servers

  Wired network-object

  wireless network object

  object-group service DM_INLINE_SERVICE_7

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_8

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_9

  service-object MSQL

  service-object RDP

  object-group service DM_INLINE_SERVICE_10

  service-object MSQL

  service-object RDP

  the tcp destination eq ftp service object

  object-group service DM_INLINE_SERVICE_11

  service-object RDP

  the tcp destination eq ftp service object

  outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1

  Note to access list OLTP Development Office of recovery outside_access_in

  outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group

  Comment from outside_access_in-access Eiresoft access list

  outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group

  outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group

  Note to outside_access_in access to OLTP for target recovery Office Access list

  outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group

  outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group

  Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server

  outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group

  Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft

  outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group

  Note to outside_access_in access from the 2nd IP Eiresoft access list

  outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group

  outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group

  outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group

  outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  no permit-nonconnected arp

  NAT (inside, outside) source Dynamics one interface

  NAT (inside, outside) static source CIX-host-1 External_CIX-host-1

  NAT (inside, outside) static source Development_OLTP External_Development_OLTP

  NAT (inside, outside) static source TMC_Webserver External_TMC_Web

  NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP

  NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover

  NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver

  NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 92.51.193.156 255.255.255.252 outside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac

  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac

  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac

  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac

  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit

  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac

  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set pfs
  peer set card crypto outside_map 1 92.51.193.158
  card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
  outside_map interface card crypto outside
  trustpool crypto ca policy
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 allow outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 77.75.100.208 255.255.255.240 outside
  SSH 92.51.193.156 255.255.255.252 outside
  SSH timeout 5
  Console timeout 0

  dhcpd outside auto_config
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  internal GroupPolicy_92.51.193.158 group strategy
  attributes of Group Policy GroupPolicy_92.51.193.158
  VPN-tunnel-Protocol ikev1, ikev2
  username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
  tunnel-group 92.51.193.158 type ipsec-l2l
  tunnel-group 92.51.193.158 General-attributes
  Group - default policy - GroupPolicy_92.51.193.158
  IPSec-attributes tunnel-group 92.51.193.158
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
  : end

  Hello

  There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.

  All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.

  Here are a few suggestions on what to change

  ASA1

  Minimal changes

  the object of the LAN network

  192.168.10.0 subnet 255.255.255.0

  being REMOTE-LAN network

  255.255.255.0 subnet 192.168.100.0

  NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

  no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

  That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

  Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.

  Other suggestions

  These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.

  PAT-SOURCE network object-group

  source networks internal PAT Description

  object-network 192.168.10.0 255.255.255.0

  object-network 192.168.20.0 255.255.255.0

  object-network 192.168.40.0 255.255.255.0

  NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

  No source (indoor, outdoor) nat Dynamics one interface

  no nat (wireless, outdoors) source Dynamics one interface

  no nat (servers, outside) no matter what source dynamic interface

  The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.

  Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.

  network of the SERVERS object

  subnet 192.168.20.0 255.255.255.0

  network of the VPN-POOL object

  192.168.50.0 subnet 255.255.255.0

  NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL

  no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

  The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.

  no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

  It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

  ASA2

  Minimal changes

  the object of the LAN network

  255.255.255.0 subnet 192.168.100.0

  being REMOTE-LAN network

  192.168.10.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

  no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

  That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

  Finally, we remove the old rule that generated the ASDM.

  Other suggestions

  PAT-SOURCE network object-group

  object-network 192.168.100.0 255.255.255.0

  NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

  No source (indoor, outdoor) nat Dynamics one interface

  The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.

  no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

  It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

  I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.

  Hope this makes any sense and has helped

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• ASA 5505 DMZ for the guest wireless access

  Hello

  Here is my delima:

  I'm deploying an Apple Airport Extreme BaseStation with Airport Express 7 "repeaters" throughout my network/building. Apple only allows only two wireless networks, public and private. Your selection of only can 192.168.x.x, 172.13.x.x or 10.10.x.x for each subnet. NO tagging VLAN.

  It wasn't my decision... Apple CEO hs fever.

  So Im stuck on how to implement this without VLAN. The comments/public subnet needs to be isolated outside access. While the private subnet requires access to both.

  Any suggestion would be greatly apprecaited.

  What will the Security Plus license allow me to do?

  Security over the license allows the use of circuits for the ASA 5505.  It also increases the maximum number of VLANS configurable at 20.  Allows active failover / standby and increases the number of authorized IPsec VPN tunnels.

  The problem with the basic license is that you can have 3 VLAN configured and the 3rd VLAN is a VLAN 'restricted '.  This means that you can not pass traffic to or from inside VLAN on the 3rd VLAN (or DMZ VLAN if you prefer to call it that.)  So this VLAN DMZ won't be able to communicate with the internet.

  So, if your private wireless network and the local network will be on the same subnet your public wireless network can be in VLAN 3.  If this isn't the case, you will need to get the security over the license.

  --
  Please do not forget to rate and choose a good answer

• Issue of ASA 5505 VPN licenses

  I have three places that I want to connect via vpn site-to-site deployed on three ASA 5505. How is the term 'Peers' in the text of license, affecting my script? Each peer ASA in a solution from site to site, or each transmission of user data in the established tunnel also counted?

  Users, passing through the tunnel of site to another are not counted. Only the peers themselves.

• Write syslog to ASA 5505 VPN tunnel on syslog server?

  Hello

  Is it possible to let the ASA 5505 write syslog messages to a syslog server on the core network where the ASA 5550 is? (on the ipsec tunnel?)

  I tried this. The tunnel is up, but I get the message from routing could not locate the next hop for the NP (ASA 5505 ip) udp inside: (ip of the syslog server).

  THX,

  Marc

  MJonkers,

  I would suggest that you configure inside interface as the interface for management access. Include IP and IP address NAT syslog server interface inside 0 ACL and ACL crypto.

  You can order the "access management" when you want to run an ASA inside of interface through the VPN 7.2 below command reference:

  http://www.Cisco.com/en/us/customer/docs/security/ASA/asa72/command/reference/m_72.html#wp1780826

  I am running the VPN configuration on 8.2 and querying SNMP works.

  I hope this helps.

  Thank you

• On ASA 5505 VPN cannot access remote (LAN)

  I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.

  Tyler

  Just remove the line of nat (outside) and ACL outside_nat0_outbound.

  And talk about these statements:

  IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).

  2, crypto isakmp nat traversal 10 or 20

  3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.

  4, create the other ACL (ST) with different name and source and destination like no nat ACL.

  5, then type nat (inside) 0 access-list sheep

  6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).

  Concerning

• Problem setting out by ASA 5505 VPN

  While inside a network secured by an ASA 5505, I can't establish a PPTP VPN on. The ASA will connect the following:

  09-2009 20:50:09 creating 305006 24.13.209.125 regular translation failed for the internal protocol 47 src: 192.168.132.108 dst outside:xxx.xxx.xxx.125

  I looked at the msg of error in line, but for some reason, I'm just not understand what he says. How can I fix it? Let me know if you have any questions... Thank you guys!

  Colombia-British

  Hello

  Enable pptp inspection

  pixfirewall (config) #policy - map global_policy

  pixfirewall(config-pmap) #class inspection_default

  pixfirewall (config-pmap-c) #inspect pptp

  Go to this link for the use of pptp/gre info background detail under various codes.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080094a5a.shtml

  Concerning

• Cisco ASA 5505 VPN passthrough

  Hello

  @home i'f installed a Cisco asa 5505 because the provider has the modem cable in transparent mode. So I have the public IP address to my firewall.

  Also for the training because we have in the work of the asa. So I have no feeling with her.

  but sometimes I have to build a VPN session to a server at work. But I do not get a connection to the server. If I remove the ASA 5505, then the connection to the server of work is great. But if to ASA 5505 is back in its place. It does not log VPN to the outside world.

  Could someone point me in the right direction?

  It is possible to create a connection out to the Cisco ASA5505 VPN.

  Thanks in advance

  Greetings

  Palermo

  Hi Palermo,

  You do not have to mention the type of VPN connection, you use.

  If the PPTP protocol then you need to inspect the traffic for the SAA allow again from 'outside '. Try the following:

   ! class-map inspection_default match default-inspection-traffic ! policy-map global_policy class inspection_default inspect pptp ! service-policy global_policy global !

  see you soon,

  SEB.