ASA 5510 with AIP SSM-10

Similar Questions

• Cisco ASA 5510 + license + AIP - SSM

  Hello.

  I have this box.

  I have a few questions about it.

  (1) I'll be able to update the firmware (from 8.2 to 8.3 or greater for example) without smarnet for ASA 5510? And what can not do without smartnet?

  (2) I have only AIP-SSM-10 module this ASA 5510. is there a smartnet, too? And when I buy only one module is it build in a subscription for 1 year for the signatures of the IPS?

  (3) if I have the Cisco ASA 5510 base license, my IPS on AIP-SSM-10 will work?

  (4) as I foresee in a purchase of the year a 5510 more with the same module and mount ther of failover. I really need license Security more than failover (active / standby)? For active/active, I know I need one, Yes?

  Please help me.

  (1) you must Smartnet in order to download the software from the download from cisco.com site.

  (2) Yes, there is also a smartnet for the AIP module. Module AIP does not come with one year subscription, but you can ask for a demo license.

  (3) Yes, the basic license is OK for the AIP module.

  (4) Yes, you would need license security more on the two ASA to be able to run any type of failover on ASA5510.

  Hope that answers your questions.

• ASA 5520 with AIP - SSM

  Dear all,

  I'm in the process of implantation of the product above of title to one of the clients.

  I am very familiar with the configuration of the firewall, but the module AIP - SSM is than I do the first time.

  Please I need your help to do the configuration.

  Is it possible by using ASDM to configure, if yes please give me the steps and procedures to complete the work

  Thanks in advance

  Swamy

  Hi S,

  Very easy:

  Connect to the ASA, activate mode and then connect to the IPS via the command "session 1".

  You are then connected to the console of the IPS. Enter the user name "cisco" and the password "cisco" and run the Setup program for the basic config (address IP etc). After that, you can either connect directly on IP addresses via a web browser or through ASDM.

  Then I recommend you read the setup guide for IP addresses that it can be very intense (configuration/tweaking signatures etc.)

  I hope this helps!

  See you soon

  JC

• transparent mode with AIP-SSM-20

  I currently have an ASA5510 routed with AIP-SSM-20 mode.

  It is necessary to use a connection in optical fiber between the ASA and ASA on the campus, so the AIP - SSM will need to be removed and replaced by the SSM - 4GE.  This section should present no problems.

  However, this will remove the IPS device, and I always want to use IPS.

  So what I think is to get another ASA5510, install the AIP - SSM, configure ASA for transparent and put it between the inside of the ASA routed and my local network.  The ASA transparent would be strictly works in the form of an IPS appliance.

  The installation program should look like this:

  Internal LAN <> ASA transparent with IPS <> routed ASA <> WAN

  The AIP - SSM can always perform with the ASA in transparent mode IPS?

  Is it possible to configure the ASA and AIP - SSM such as traffic to and from a particular server completely ignores the AIP - SSM?

  I have a couple of file servers which generate heavy traffic and can overload the AIP - SSM.

  Kind regards.

  AFAIR, it is no installation AIP in a transparent firewall problem.

  "The SAA in transparent mode can execute an agreement in principle.  In the event that the AIP fails,

  the IPS will fail-open and the ASA will continue to pass traffic.
  
  However, if an interface or cable fails, then traffic will stop.  You
  
  would need a failover pair to account for this failure event, which
  
  means another ASA and matching AIP."
  
  

  And no there is no problem to exclude certain hosts/ports/subnets inspection by IPS via MPF.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/IPS.html#wp1050744

  What I consider however is however if the ASA 5510 as second level firewall for 5520 s will be enough.

  http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

  HTH,

  Marcin

• ASA 5510 with double tis

  Hello.. It is possible for cisco asa 5510 hitting the load balancing between double tis? and what will the configurations? Thanks... :D

  Hello

  ACB is used normally for balancing the load on network devices. Another one of my posts on this forum and I quote:

  The ASA/PIX does not ACB support to date. I told her on the road map.

  As a work around, you can run multiple contexts, if its possible to break your lan into two subnets.

  And also allocate the Internet interfaces appropriate to each context (with the default gateway pointing to the respective service providers).

  This link will help you get started:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808d2b63.shtml

  Please NOTE: dynamic routing and virtual private networks are not supported in Multiple context mode.

  Another alternative, if WAN links end on a router (and not the firewall), you could use this router to the ACB.

  Concerning

  Farrukh

• Inspection of traffic between hair-pinning VPN on a SAA with AIP SSM.

  Hello

  I want to deploy an ASA as a VPN endpoint and to use the AIP SSM module to inspect and provide protection for inbound traffic arriving on a VPN and start on another within the same ASA. I guess it's possible because traffic is unencrypted in the ASA State and must be intercepted by the class plan. Anyone who has done this or can anyone confirm that this will work?

  Thank you very much

  Wil Bowes

  If the ASA finishes the VPN, then indeed it can also inspect internally. The decryption happens before "module controls" for inbound traffic and the arrival of "control module" before encryption for outgoing traffic. If you can do it.

  I hope it helps.

  PK

• VPN on ASA-5510 with Configure a dynamic encryption card

  Hi all

  My name is ping, I have ASA-5510 for site to site VPN configuration, but am not clear with a few conifguration on ASA-5510 series, not sure on poin than, when I install on other sets of cisco router I can use

  ASA2 (config) #crypto card outside-card 10 ipsec-isakmp

  % NOTE: this new map encryption will remain disabled until a peer

  and a valid access list have been configured.

  ........

  but, when I configure ASA 5510 it as below:

  mtelcoASA2 (config) # crypto?

  set up the mode commands/options:

  CA Certification Authority

  dynamic-map set up a dynamic encryption card

  IPSec transform-set set, life of the IPSec Security Association and fragmentation

  ISAKMP configure ISAKMP

  main activities key long-term

  card to configure an encryption card

  ASA2 (config) # map outside-map 10 ipsec-isakmp crypto ?

  set up the mode commands/options:

  Entry dynamic is a dynamic map

  "Set up a dynamic crypto map" which uses for and why I can't use only "map outside-map 10 ipsec-isakmp crypto" and if not can't, can I skip this command or tell me the other way with explanation with nicely,

  Thank you very much

  hot topic,

  Ping,

  Just use crypto card outside-map 10 match/set without ipsec-isakmp key word and it will be fine.

• Unable to connect to server vpn behind ASA 5510 with windows clients

  Hi all

  I've seen a number of posts on this and followed by a few documents of support on this issue, but I'm totally stuck now, nothing seems to work for me.

  This is the usual scenario, I have a VPN windows 2003 Server sat on the lan deprived of our ASA 5510 firewall, and I try to get my Windows XP / 7 laptop computers to connect to it.

  Within the ASDM:

  (1) Server Public created for Protocol 1723

  (2) Public created for the GRE protocol Server

  3) created two public servers have the same public and private addresses

  (4) the foregoing has created config Public Private static route in the section NAT firewall

  (5) rules to Firewall 2 also created above on the external interface for both 1723 and GRE

  When you try to connect, I get the following entry in the debug log.

  6 August 6, 2010 17:09:37 302013 195.74.141.2 1045 1723 ChamberVPN-internal built ride connection TCP 1889195 for outside:195.74.141.2/1045 (195.74.141.2/1045) to the inside: ChamberVPN-internal/1723 (XXX.XXX.XXX.XXX/1723)

  but nothing else.

  The server shows not attempting a connection so I think I'm missing something on the firewall now.

  Also inside interface there is a temporary rule:

  Source: no

  Destination: any

  Service: IP

  Action: enabled

  This should allow all outbound traffic only as far as I know...

  Any help would be greatly appreciated.

  Chris

  Hi Chris,

  ASA newspaper indicates that the connection is interrupted because of "syn timeout. This means that asa receives no response from the Windows Server. Right now, we need to clarify some points.

  1 - your vpn server committed a correct default gateway error or the path that lies in your fw interface asa.

  is 2 - possible to start capturing packets on Windows Server. Hereby, we can get data flow information beetween client and server. And we can be sure that Windows Server wonders vpn.

  Ufuk Güler

• Automatic update AIP-SSM-10 and ASA 5510 (Beginner)

  I see that it is possible to automate the updates of the ASA 5510 and AIP SSM via FTP on my own server. Is it possible to automate the download directly from Cisco.com?

  Thank you!

  Jeremy

  Jeremy, the answer to your question is correct, as far as the Cisco products are concerned. So I wrote a PERL app that does exactly that, and I published an article about it in the June 2007 issue of Sys Admin magazine. Here's the article online: http://www.samag.com/documents/s=10128/sam0706a/0706a.htm

  And it is also on my site, with a tar of scripts to:

  http://www.LHB-consulting.com/pages/apps/index.html

  Good luck.

  -Lisa

• Is a CSC module must use Smartfilter with an ASA 5510?

  We use a PIX 515E and an external Smartfilter server for URL filtering for many years. Works well, but we want to add the IDS feature. The road ahead for this seems to be to get an ASA 5510 with AIP module. Can anyone confirm if we continue to use the order of FILTER of URL (with Smartfilter specified as a salesman and pointed to the IP address of the server Smarfilter) as we do on the PIX? Sales of Cisco tells me that I need a module of CCS for it which means I can't have a module AIP, but the way I read it which seems to be only if you use URL of the CSC (user account subscription) database to perform the filtering. We do not want. We left 3 years on our contract of Smartfilter. I just talked to someone who has an ASA 5510 without a CSC module and it was successfully entered a FILTER of URL command in his ASA, as you would on a PIX. Why wouldn't work?

  for the URL filtering, NO, you need not any type of license, this isn't a feature defined licensed, its rather a feature of configuration

• AIP SSM-10 and tests

  In my lab, I have a new 5510 with AIP - SSM card.

  In my view, it is configured correctly to assess traffic, but I can't be sure.

  This is part of the configuration of the ASA:

  Global class-card class

  match any

  class-map inspection_default

  match default-inspection-traffic

  World-Policy policy-map

  class inspection_default

  inspect the ftp, etc.,

  Global category

  IPS inline help

  global service-policy global_policy

  I have a PC to a switch, go to the ASA (inside interface)

  The ASA outside interface goes to a VLAN separate on the switch.

  Both interfaces VLANS configured.

  Is there a command ping, or other traffic I can generate from PC that will throw an alert?

  I tried Ping s of a bogus address, but which did not cause an event.

  How will I know if the traffic actually crosses the ID?

  Thank you.

  Hello Jimmy

  Lass-map: global-class

  IPS: Status of card upward, inline mode rescue

  Package of 0 Packet output 0 0 drop, discount entry to zero - drop 0

  No package get the IPS module

  You have told me is assigned to virtual sensor 0 on the right side of the AIP - SSM?

• The AIP SSM mode

  I bought an ASA 5510 with module SSM for IPS get in PCI compliance. I'll implement the SSM and I don't know if I have to use online or "Promiscuous" mode to control traffic. I'm afraid I'll slow down if I do online but I don't know if the "Promiscuous" mode is sufficient to meet the PCI standards. Nobody knows who can or should be used?

  Here ya go:

  http://www.ccbootcamp.com/PCI/design-guide.PDF

  http://www.ccbootcamp.com/PCI/CISPVISA.PDF

  -brad

  http://www.ccbootcamp.com

  (please NOTE the message if it helps!)

  (Perhaps that the moderator can make this a sticky!)

• Rules of politics on the ASA AIP - SSM services

  Salvation of the forumers

  I have an ASA with AIP - SSM. I want to protect the LAN private outside the internet attack.

  I would check the meaning of the ACL on ASDM firewall > policy of Service rule

  1. am I right to set the source: external interface, destination: 172.16.0.2

  or 2. destination value: 10.10.0.0 / 16

  Thank you

  Noel

  To respond to your request in simple just do your Service policy with the IP address that is seen by the firewall. If the IP address 10.10.0.0/16 are natted on the router with 172.16.0.2, then all IP addresses, hit on the firewall will be 172.16.0.2 so make your destination with 172.16.0.2 else if the natting is on the firewall for 10.10.0.0/16 then point the destination to 10.10.0.0/16.

• ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone

  Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...

  We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.

  This is the phone that we seek;

  http://www.Cisco.com/en/us/prod/collateral/voicesw/ps6788/phones/ps10499/ps11005/data_sheet_c78-603725.html

  I want to know is the Anyconnect Essentials license will work with these IP phones?

  When I do a version of the show,

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?

  Hi Leo,

  you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»

  ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.

  CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574

  HTH

  Herbert

• AIP SSM-10

  Hi EXP.

  1st time for me to work with AIP-SSM-10, I ASA5510 and AIP-SSM-10,.

  Firewall (5510):

  inside the 192.168.55.252

  87.191.101.1 outside

  DMZ 172.16.0.1

  where to plug the AIP SSM-10 what ip address I have to give him and how can I be savvy to ensure that is to have such as ping or traceroute ip connectivity. what I'm missing, it is the ip address.

  I gave an ip address to the management interface and I left ping but I couldn't ping the AIP SSM-10 between the firewall.

  Please help,

  (1) of the SAA, you would session in the module, and you must configure the ip address on this module with the command "setup."

  (2) what you just set up the ip address is assigned to the interface on this module.

  (3) this interface on the module must be physically connected to your network. You can configure a unique ip address in the same subnet as your ASA inside the interface.

  Here's a diagram of the module with the port interface / hardware:

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/installation/guide/hw_installing_ssm.html

  Here's how to run the command "setup":

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/installation/guide/hw_initializing.html