ASA for DC and Internet purchasing

Similar Questions

• The ASA for FW and IPS options with high availability

  Question 1:

  -----------

  I'm looking for IPS solution for the customer and the verification of the ASA next part number;

  ASA5540-AIP20-K9

  (ASA 5540 appliance w / AIP-SSM-20, SW, HA, 4GE + 1FE, 3DES/AES)

  What does AP mean here - what software?

  In this case you have to buy a second unit (at the same price) for the recovery of?

  (I wondered if ASA has also a cost - efficient as PIX failover solution-discounted price for the unit of failover).

  If I choose the ASA VPN edition is it possible to add IPS inside module?

  Hello

  Q: what does AP means here - what software? In this case you have to buy a second unit (at the same price) for the recovery of?

  The "ASA5540-AIP20-K9" is only for 1 unit of ASA, with function of software HA (active/active, active / standby). You can add/buy another unit to achieve HA/recundancy.

  I think that the price of a unit all them is always the same, ASA has no unit to voluntarily make the function FO.

  Q: if I choose the ASA VPN edition is it possible to add IPS inside module?

  Large malicious Intrusion Prevention & mitigation program is included, as mentioned in the 'picture' 3 Security of the network to the VPN gateway"in:

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd80402e3f.html

  Rgds,

  AK

• ASA5505: Configure the ASA for IPSec and SSL VPN?

  Hello-

  I currently have my 5505 for SSL AnyConnect VPN connections Setup.  Is it possible to set up also the 5505 for IPSec VPN connections?

  So, basically my ASA will be able to perform SSL and IPSec VPN tunnels, at the same time.

  Thank you!

  Kim,

  Yes, you can configure your ASA to support the AnyConnect VPN IPSec connections and at the same time.  In short, for the configuration of IPSec, you should configure at least a strategy ISAKMP, a set of IPSEC, encryption, tunnel group card processing and associated group policy.

  Matt

• DMVPN and INTERNET VIA HUB RENTAL ISSUES

  Hello everyone,

  I really wish you can help me with the problem I have.

  I explain. I test a double Hub - double DMVPN Layout for a client before we set it up in actual production.
  The client has sites where routers are behind some ISP routers who do NAT.

  

  How things are configured:

  -All rays traffic must go through the location of the hub if no local internet traffic on the rays.
  -Hub 1 and 2 hub sends a default route to rays through EIGRP. But only Hub 1 is used.
  -Hub 1 is the main router to DMVPN. In case of connection / hardware failure of the Internet Hub 2 become active for DMVPN and Internet.
  -Hub 1 and 2 hub are both connected to an ISP and Internet gateway for rays.
  -Hub 1 and 2 hub are configured with IOS Firewall.
  -On the shelves I used VRF for separate DMVPN routning Global routning table so I could receive a default route of 1 Hub and Hub 2 to carry the traffic of rays to the Internet via the location of the hub

  What works:

  -All rays can have access to the local network to the location of the hub.
  -All the rays can do talk of talk
  -Working for DMVPN failover
  -Rais NOT behind the router NAT ISP (i.e. the public IP address) directly related to their external interface can go Internet via hub location and all packages are inspected properly by the IOS and Nat firewall properly
   
  What does not work:

  -Rays behind the NAT ISP router can not access Internet via Hub location. They can reach a local network to the location of the hub and talk of talks.
  IOS Firewall Router hub shows packages from rays of theses (behind a NAT) with a source IP address that is the router og PSI of public IP address outside the interface. Not the private address LAN IP back spoke.
  In addition, the packets are never natted. If I do some captge on an Internet Server, the private source IP is the IP LAN to the LAN behind the rays. This means that the hub, router nat never these packages.

  How to solve this problem?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Tabel - Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Well I don't know that's why I need your help/advice :-)

  I don't know that if I have to configure a VRF on the location of the hub gets also like things might mess upward.

  The problem seems to be NAT - T the rays that are not behind a NAT, among which go over the Internet through a Hub and inspection of Cisco IOS and NAT are trying to find.

  I tested today with the customer at the start them talking behind nat could ping different server on the Internet but not open an HTTP session. DNS was to find work. The IOS Firewall has been actually

  inspection of packages with private real IP address. Then I thought it was a MTU issue, so I decided to do a ping on the Internet with the largest MTU size and suddenly the pings were no more.

  I could see on the router Hub1 IOS Firewall was inspecting the public IP of the ISP NAT router again alongside with rays and not more than the actual IP address private. Really strange!

  Attached files:

  I attach the following files: a drawing of configuration called drawing-Lab - Setup.jpeg | All files for HUB1, BRANCH1 and BRANCH2 ISP-ROUTER configs, named respectively: HUB1.txt, BRANCH1.txt, BRANCH2.txt and ISP - ROUTER .txt

  Hub1 newspapers when ping host 200.200.200.200 on the Internet of Branch2 (behind the NAT ISP router):

  Branch2 #ping vrf DMVPN-VRF 200.200.200.200 source vlan 100

  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 200.200.200.200, time-out is 2 seconds:
  Packet sent with a source address of 192.168.110.1
  .....
  Success rate is 0% (0/5)

  * 06:04:51.017 Jul 15 UTC: % FW-6-SESS_AUDIT_TRAIL_START: start session icmp: initiator (110.10.10.2:8) - answering machine (200.200.200.200:0)

  If the IOS Firewall does not inspect the true private source IP address that can be, in this case: 192.168.110.2. He sess on the public IP address.

  HUB1 #sh ip nat translations
  Inside global internal local outside global local outdoor Pro
  ICMP 80.10.10.2:1 80.10.10.2:1 100.10.10.2:1 100.10.10.2:1
  ICMP 80.10.10.2:2 80.10.10.2:2 110.10.10.2:2 110.10.10.2:2
  UDP 80.10.10.2:4500 80.10.10.2:4500 110.10.10.2:4500 110.10.10.2:4500

  There is no entry for packets of teas present NAT

  Captge on Tunnel 1 on Hub1 interface (incoming packets in):

  7 7.355997 192.168.110.1 200.200.200.200 request ICMP (ping) echo
  So that the firewall controllable IOS to the 110.10.10.2:8 public IP sniffing capture said that the package come from private real IP address

  Inhalation of vapours on the server (200.200.200.200) with wireshark:

  114 14.123552 192.168.110.1 200.200.200.200 request ICMP (ping) echo

  If the private IP address of source between local network of BRANCH2 is never natted by HUB1

  If the server sees the address source IP private not natted although firewall IOS Hub1 inspect the public IP address 110.10.10.2:8

  Hub1 newspapers when ping host 200.200.200.200 on the Internet of Branch1 (not behind the NAT ISP router):

  Branch1 #ping vrf DMVPN-VRF 200.200.200.200 source vlan 100

  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 200.200.200.200, time-out is 2 seconds:
  Packet sent with a source 192.168.100.1 address
  !!!!!

  * 06:05:18.217 Jul 15 UTC: % FW-6-SESS_AUDIT_TRAIL_START: start session icmp: initiator (192.168.100.1:8) - answering machine (200.200.200.200:0)

  This is so the firewall sees the actual private IP which is 192.168.100.1

  HUB1 #sh ip nat translations
  Inside global internal local outside global local outdoor Pro
  ICMP 80.10.10.2:1 80.10.10.2:1 100.10.10.2:1 100.10.10.2:1
  ICMP 80.10.10.2:2 80.10.10.2:2 110.10.10.2:2 110.10.10.2:2
  UDP 80.10.10.2:4500 80.10.10.2:4500 110.10.10.2:4500 110.10.10.2:4500
  ICMP 80.10.10.2:22 192.168.100.1:22 200.200.200.200:22 200.200.200.200:22

  The real private source IP address is also find natted 1 Hub outside the public IP address

  Captge on Tunnel 1 on Hub1 interface (incoming packets in):

  8 7.379997 192.168.100.1 200.200.200.200 request ICMP (ping) echo

  Real same as inspected by IOS Firewall so all private IP address is y find.

  Inhalation of vapours on the server (200.200.200.200) with wireshark:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Tabel - Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  67 10.441153 80.10.10.2 200.200.200.200 request ICMP (ping) echo

  So, here's all right. The address is natted correctly.

  __________________________________________________________________________________________

  Best regards

  Laurent

  Hello

  Just saw your message, I hope this isn't too late.

  I don't know what your exact problem, but I think we can work through it to understand it.

  One thing I noticed was that your NAT ACL is too general. You need to make it more

  specific.  In particular, you want to make sure that it does not match the coming of VPN traffic

  in to / out of the router.

  For example you should not really have one of these entries in your NAT translation table.

  HUB1 #sh ip nat translations
  Inside global internal local outside global local outdoor Pro
  ICMP 80.10.10.2:1 80.10.10.2:1 100.10.10.2:1 100.10.10.2:1
  ICMP 80.10.10.2:2 80.10.10.2:2 110.10.10.2:2 110.10.10.2:2
  UDP 80.10.10.2:4500 80.10.10.2:4500 110.10.10.2:4500 110.10.10.2:4500

  Instead use:

  Nat extended IP access list
  deny ip any 192.168.0.0 0.0.255.255 connect
  allow an ip
  deny ip any any newspaper

  If you can use:

  Nat extended IP access list
  deny ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255 connect
  IP 192.168.0.0 allow 0.0.255.255 everything
  deny ip any any newspaper

  Also, I would be very careful with the help of the "log" keyword in an ACL, NAT.

  I saw problems.

  What are the IOS versions do you use?

  Try to make changes to the NAT so that you no longer see the entries of translation NAT

  for packages of NAT - T (UDP 4500) in the table of translation NAT on the hub. It may be

  This puts a flag on the package structure, that IOS Firewall and NAT is

  pick up on and then do the wrong thing in this case.

  If this does not work then let me know.

  Maybe it's something for which you will need to open a TAC case so that we can

  This debug directly on your installation.

  Mike.

• I reinstalled iTunes for windows and downloaded two albums purchased on the iTunes store. Both albums have digital booklet in it but it seems that it has not downloaded. In the store, it seems certain. How should I download them?

  I reinstalled iTunes for windows and downloaded two albums purchased on the iTunes store. Both albums have digital booklet in it but it seems that it has not downloaded. In the store, it seems certain. How should I download them?

  Try iTunes Store > Quick links > purchase > music > not on my computer.

  If they do not show here, then visit https://reportaproblem.apple.com/

  TT2

• Can someone help please. Internet Explore opens not with google or yahoo. Everytime I open in Explorer, I get a message page cannot be displayed or link seems to be broken for yahoo and google.

  Internet Explorer not open google or yahoo home page. Interface of mail yahoo and google is broken.

  Hi Success65.

  Thanks for posting. Please, try the following steps.

  Thanks for posting. Please try the following and see if it you solved.

  Method 1: Run the Network Diagnostics tool in Internet Explorer to do this, follow these steps:

  1. Start Internet Explorer, and then try to access the Web page that displays the error message.
  2. On the page that displays an Internet Explorer error message, click diagnose connection problems . The Network Diagnostics tool will run. When the tool has finished, it will notify if you one of the following results:
     • He was unable to find a problem.
     • It has detected a problem. In addition, the tool will provide guidance on the next steps to take to resolve the problem.
     Note Users of Internet Explorer 6, click on detect network settings
  3. Click IP address, and note the IP address. You may have to it for future troubleshooting.
  4. Follow the steps in the Network Diagnostics tool to fix any connection problems.
  5. Start Internet Explorer.

  If you receive the same error message, go to the next method.

  Note You cannot use this method in Windows 7. The Network Diagnostics tool has been improved and replaced by the convenience of the Internet. Follow method 8 to run the troubleshooters. Method 2: Reset the modem or the router to do this, follow these steps:

  1. Disconnect the cable that connects the computer to the modem.
  2. Turn off the modem and the router.
     Collapse this tableauAgrandir this table

     Note	If the modem or the router does not have a power switch, turn off the power to the modem or to the router.

  3. Restart the computer.
  4. Once your computer has been restarted, turn on the modem or the router, connect the cable from the computer to the modem or the router, and restart the computer.
  5. Make sure that all network cables are properly connected.
  6. Start Internet Explorer.

  If you receive the same error message, go to the next method. Method 3: Use the delete browsing history if resetting the modem or the router has not resolved the problem, delete your browsing history might help. Follow these steps to delete your temporary Internet files, history and form data:

  1. Start Internet Explorer.
  2. On the Tools menu, click Internet Options.
  3. Under browsing history, click delete.
  4. Select the check box next to the Web site data preserve Favorites.
  5. Select the check box next to Temporary Internet files.
  6. Select the check box next to Cookies.
  7. Select the check box next to the history.
  8. Select the check box next to form data.
  9. Select the checkbox next to InPrivate filtering data.
  10. At the bottom of the window, click delete.
  11. Close Internet Explorer and restart Internet Explorer, and then try to access the Web page.
  1. Start Internet Explorer.
  2. On the Tools menu, click delete browsing history.
  3. Select the check box next to Temporary Internet files.
  4. Select the check box next to the history.
  5. Select the check box next to form data.
  6. Select the check box next to Cookies.
  7. At the bottom of the window, click delete.
  8. Close Internet Explorer and restart Internet Explorer, and then try to access the Web page.
  1. Start Internet Explorer.
  2. On the Tools menu, click Internet Options.
  3. In the Temporary Internet files section, click delete filesand then click to select the text box delete all offline content , and then click OK.
  4. In the history section, click clear history, and then click Yes.
  5. Close Internet Explorer and restart Internet Explorer, and then try to access the Web page.

  If you receive the same error message, go to the next method. Method 4: Use the Internet Explorer (No Add-ons) mode to do this, click Start, point to programs, point to Accessories, point to System Tools, and then click Internet Explorer (No Add-ons).

  
  Note The Internet Explorer (No Add-ons) mode is only available for Internet Explorer 7 and Internet Explorer 8.

  If this resolves the problem, follow these steps to isolate the browser add-on that is causing the problem:

  1. Click Toolsand then click Internet Options.
  2. Click on the programs tab, and then click Manage Add-ons.
  3. Click an add-on in the name list, and then click disable.
  4. Repeat step 3 until you identify the add-on that is causing the problem.

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Settings MMS for blackBerry Smartphones and Internet for 9700

  Can anyone help with MMS and Internet for Bold 9700 parameters on the network of Virgin Mobile Australia? I am able to browse internet through Opera mini using APN: VirginInternet but no luck with MMS? Solves them this problem or is it true that Virgin does not support Blackberry devices.

  Hello and welcome to the community!

  On BB, access to a range of services is enabled by the existence, on the device, the appropriate Service books. Service books are delivered to the appliance by the network of carriers... but, normally, only for these models of specific device that takes the network carriers supported and none support BB all models. If, as you think, your carrier supports no. BB models, then you can't expect their network to offer the Service books, which means that these services that require some SBs won't work, which includes MMS. But only they can answer the question of whether to their network supports the BBs at all and your specific model BB in particular number.

  Good luck!

• scalable design vcs-e for the clients of MPLS and internet

  Hi all

  I think of an evolutionary design of VCS-highway in a service provider architecture.

  Some clients reach vcs-e across one MPLS network, another customer over the internet (each client with its own vcs - c).

  I have a vcs-e with dual NICs and nat enabled.

  VCS - e is a private network.

  In this architecture, if I nat vcs-e in one public ip address, I can't inject the public IP address in the VPN client (clients use the address private, and anyway, they will not receive a public IP, MPLS and the internet). And I can't inject a private Internet ip address. In addition, every customer wants to use an ip address of vcs - e compatible with their plan ip... then maybe customer wants to use an address of 172.31.x.y and a B client an IP address of 192.168.x.y.

  Best solution would be to nat vcs-e address in different ip address for each client / internet through the firewall, for example vcs-e 10.1.1.1 in 172.31.24.1 for the customer has, in 192.168.24.1 for client B and 80.x.y.z for the internet, according to the firewall context... but I'm not sure that I can do (I can? I think I can only the ip address of nat vcs-e statically 1 to 1).

  I am attaching a figure illustrating the design of the network.

  Any suggestion?

  Hello

  In your design, it is allowed to do NAT between VCS - C and VCS-E if you configure using links/box of course, which I think is what you plan to do. A nearby area will fail in this design.

  If your customer can have a VCS - C on their private network and that you connect to your VCS-E through a NAT firewall as you describe as the "best solution".  There is no need to NAT any return to the client IP address, since the VCS - C will make an outbound connection only for the VCS-E.

  Robert

• I bought a CC of Photoshop, Lightroom + bridge CC yesterday, paid for 1 year. In my creative cloud Manager, it seems that I have downloaded the trial versions of CC of Photoshop and Lightroom CC and also purchased versions. I'm not sure what I'm supposed

  I bought a CC of Photoshop, Lightroom + bridge CC yesterday, paid for 1 year. In my creative cloud Manager, it seems that I have downloaded the trial versions of CC of Photoshop and Lightroom CC and also purchased versions. I don't know what I have to do. Is the version that I use the purchased version? I'm afraid that I always use the 30 day trial version. It will change to that purchased once the payment by credit card has been approved? Or do I have to download some versions of Photoshop and Lightroom again? It is quite confusing. Thank you for your help.

  Your subscription to cloud shows correctly on your account page?

  If you have more than one email, you will be sure that you use the right Adobe ID?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  .

  If Yes

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  .

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• Care comparison for Oracle and Oracle Iprocurement purchasing

  Hello everyone

  Can we have a comparison sheet of the major differences between Oracle purchases and Iprocurement I searched and studied the documentation on it but could not find enough material to calculate the differences

  He would be grateful if any of you have a comparison sheet for the major differences between the two

  Thank you very much

  Major differences between the purchase of the Oracle iProcurement, and:

  Purchases:

  -----------------

  Allows creation and editing of PO, recipes etc.

  Only buyers can create and modify the POs.

  It allows to request a QUOTE, quote creation and analysis of extract.

  Allow communication automated with the provider.

  iProcurement:

  --------------------

  It is mainly used to create and modify applications write-in and demand of the contractor.

  Allows the creation of reception.

  PunchOut lets you directly access the supplier catalog.

  Provides the ability to create Confirmation works for complex orders.

• I bought two Lightroom... One for Mac and one for Windows but Mac gives me problem... it happened in judgment and now it won't open upwards - and how that I associate my Mac purchase at a monthly payment as my Windows plan? Its a plan photograph b

  I bought two Lightroom... One for Mac and one for Windows but Mac gives me problem... it happened in judgment and now it won't open upwards - and how that I associate my Mac purchase at a monthly payment as my Windows plan? Its a plan of photography by Adobe (including lightroom and photoshop)

  Hi Robertc70810949,

  It is a digression of your technical question, but you haven't purchased two separate subscriptions for creative cloud? You are probably aware of this, but just in case you're not, a single Plan of creative photography cloud allows installation and activation on two computers. These computers can be two Macs, two windows, or one of each. See Adobe Creative Cloud FAQ for more information. Of course, you can have another reason to buy multiple subscriptions, but I wanted to clarify in case you can save yourself a little money.

  Kind regards

  Del

• I have a license for Indesign and purchases another since my old computer was attacked by pirates. When you try to load to the new computer, it starts with a 30 day free period etc. I already have an ashen´me of monthly payment and seem not to be able to

  I have a license for Indesign and purchases another since my old computer was attacked by pirates. When you try to load to the new computer, it starts with a 30 day free period etc. I have a monthly payment and don't seem to be able to upload it to my account on my new computer. I have access to my account online but cannot get to the correct download page. ????

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -https://helpx.adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

• I purchased the CS4 master collection for windows and I change my computer on a Mac. How to upgrade my license?

  I purchased the CS4 master collection for windows and I change my computer on a Mac. How to upgrade my license?

  There is no option to update your CS4 license except subscribe to specially of the first creative cloud plan cuts the year for owners of CS (Adobe: creative, marketing, and document management solutions).

  Platform swaps are allowed only for the most recent released CS software (CS6).  You can get a version license Mac to CS4 by Adobe since Adobe doesn't sell older versions, and the only version of CS for sale is CS6...  CS4 is not eligible to get CS6 at an upgrade price.

  You can buy CS6 via the following page: http://www.adobe.com/products/catalog/cs6._sl_id-contentfilter_sl_catalog_sl_software_sl_c reativesuite6.htm

• LightroomCC2015 just disabled use.stating I need to purchase a license. I'm running on the plan for this and other applications. How do I fix this, please?

  LightroomCC2015 disabled just use of the develop Module. Indicating that I need to buy a license. I'm running on the plan for this and other applications. How do I fix this, please?

  Please see the troubleshooting section below.

  Reference: creative judgment Cloud 2015 to return to the mode of trial

  Let us know if that helps.

  Kind regards

  Mohit

• ASA 5510 VPN dedicated Internet connection

  I have a 5510 ASA with a second internet connection on his way.  I would like to have an internet connection dedicated to my VPN Site to Site traffic and the other left to manage the public internet traffic.   I know that I can do this with a static route, but today, I noticed the "tunnel" option  How exactly does the tunnel option work mode and it works better for my situation?

  Rob,

  (Simplification) "Tunnel" option tells what to do with traffic, once it has been for example inbound VPN decapsulted.

  In your case, static routes for remote tunnel endpoint + RRI points will do.

  M.

  Edit: I would advise yo forget about the end of the dynamics of peers (dynamic IP L2L or ezvpn) solutions on any interface that does not have a default route on this subject.