Assignment of VLAN dynamic by using the WC7520 controller

Similar Questions

• Assignment of VLAN dynamic of the Web authentication

  In a firmware WLC 4402 v.5.2.157 is possible to assign users to one VLAN dynamic based on the RADIUS response received from ACS?

  Yes and no. You can do for a WLAN 802.1 x internal, that the customer does not get an IP address, until they have completed the authentication process. To do this, you use 64/65/81, 64 802, 65 VLAN and to 81 use the name of the interface, not the number VLAN. you will also need to make sure you have AAA Overrided activated under the WLAN.

  If, as is said for Web authentication, the answer is no. The client has an IP address before being validated by the AAA server.

  HTH,

  Steve

• Assignment of VLAN dynamic RADIUS ACS 5.2 Server with NAC

  We are trying to reduce the number of ssid in our network wireless with assignment of vlan dynamic with the acs. Our problem is that we use Cisco NAC so with assignments of vlan dynamic user will be checked by the NAC. Agent of Cisco sometimes pop up and do nothing to do or give a message cannot locate server. We even got an OOB error. Someone used a VLAN dynamics with the acs and the NAC successfully? The NAC is Out of Band

  Hello

  I supported oob nac and wireless and your efforts to make the dynamic assignment of VLANs will not work because of the way in which him vlan quarantine and access are mapped to this ssid.

  This work in in-band mode, however your design. This WLAN key needs to exist because the Manager sends the snmp trap to move the client from quarantine access.

  Just as a note, I'm sure you are aware is that ISE is the evolution of the acs and the NAC. Basically this your solution to reduce the skates and posturing of the customers.

  Sent by Cisco Support technique iPad App

• OR PCI-6542: Creation of dynamic waveforms using the HSDIO library

  Hello!

  I have problems to understand how to create waveforms using the HSDIO library to run on a card PCI-6542. I need to create a program that activates a channel for 12.5 microseconds, waiting for a while (i.e. 100 samples) and activates another channel to 12.5 microseconds.

  This program must be used in a Multielement ultrasound system.

  Here the example of dynamic generation program that transforms the channels 0-2 on 1024 samples.

  /************************************************************************
  
  *
  
  *  Example program:
  
  *    DynamicGeneration.c
  
  *
  
  *  Description:
  
  *    Generates a simple model on the specified channel.
  
  *
  
  *  Pin connection information:
  
  *    None.
  
  *
  
  ************************************************************************/
  
  / * Includes * /.
  
  
  
  
  
  #include "niHSDIO.h".
  
  / * Sets * /.
  
  #define WAVEFORM_SIZE 1024
  int main (void)
  
  {
  
     ViRsrc deviceID = 'Dev1 ';
  
     ViConstString channelList = "0-2";
  
     ViReal64 sampleClockRate = 50.0e6;
  
     DataWidth ViInt32 = 4;
  ViUInt32 waveformDataU32 [WAVEFORM_SIZE];
  
     ViConstString waveformName = "myWfm";
  
     ViInt32 timeout = 10000; / * milliseconds * /.
  ViSession vi = VI_NULL;
  
     Error ViStatus = VI_SUCCESS;
  
     Bruno errDesc [1024];
  
     ViInt32 i;
  / * Initialize generation session * /.
  
     checkErr (niHSDIO_InitGenerationSession)
  
              Deviceid, VI_FALSE, VI_FALSE, VI_NULL, &vi));
  / * Assign channels for dynamic generation * /.
  
     checkErr (niHSDIO_AssignDynamicChannels (vi, channelList));
  / * Set up the clock sample parameters * /.
  
     checkErr (niHSDIO_ConfigureSampleClock)
  
              VI, NIHSDIO_VAL_ON_BOARD_CLOCK_STR, sampleClockRate));
  / * Query the data Width attribute * /.
  
     checkErr (niHSDIO_GetAttributeViInt32)
  
              VI, VI_NULL, NIHSDIO_ATTR_DATA_WIDTH, & dataWidth));
  
  
  
     / * Fill the waveform with ramp data * /.
  
     < waveform_size;="">
  
     {
  
  	   waveformDataU32 [i] = i;
  
     }
  checkErr (niHSDIO_WriteNamedWaveformU32)
  
              VI, waveformName, WAVEFORM_SIZE, waveformDataU32));
  / * Start the generation * /.
  
     checkErr (niHSDIO_Initiate (vi));
  / * Wait for all the generation * /.
  
     checkErr (niHSDIO_WaitUntilDone (vi, timeout));
  Error:
  If (error is VI_SUCCESS)
  
     {
  
        / * Print result * /.
  
        printf ("made without error. \n") ;
  
     }
  
     on the other
  
     {
  
        / * Get the description of the error and print * /.
  
        niHSDIO_GetError (vi, & error, sizeof (errDesc) /sizeof (petitioner), errDesc);
  printf ("\nError encountered\n===\n%s\n", errDesc);
  
     }
  / * log * /.
  
     niHSDIO_close (vi);
  / * prompt to go out (for the popup console windows) * /.
  
     to continue...\n");
  
     GetChar ();
  
  error return;
  
  }

  Issues related to the:

  How can I change the values in waveformDataU32 to create market reports (instead of just always on)?

  How to select the channel waveformDataU32 is applied to the?

  Thank you!

  Zachary Geier

  The waveformDataU32 table is an array of 32-bit integers. Each bit corresponds to a line on the device.  On the first clock cycle, this program outputs:

  0000 0000 0000 0000 0000 0000 0000 0000

  Then it displays the following, changing at each clock Pulse:

  0000 0000 0000 0000 0000 0000 0000 0001,

  0000 0000 0000 0000 0000 0000 0000 0010,

  ...

  and so on all the way up to 1023:

  0000 0000 0000 0000 00000011 1111 1111

  In the example that you include at the bottom, you set the least significant bit (LSB) to zero and one, actually only change one line on the output. To change all the lines, you must instead use 4 294 967 295 or 0xFFFFFFFF:

  < waveform_size;="">
  
       < 200){="" if="" sample="" number="" is="" less="" than="">
  
            waveformDataU32 [i] = 0;     Disable channels 0-2
  
       }
  
       else {}
  
            waveformDataU32 [i] = 4 294 967 295;     Otherwise turn on all channels to 800 samples
  
       }
  
   }

• Display static and dynamic photo using the Structure of the event

  Hello everyone,

  I need to display a static image with an event and then using another event, I need to keep displaying the second photo, while the first is still displayed. Simply speaking, in the attached example, I would like to have the color circle black fixed while I dynamically change the red circle.

  My attempt is shown in the attached VI with the first approach using the shift register and the second using the property node (value). Both do not work. Does not erase the previous red circle, or the black circle also gets deleted.

  I'd appreciate any help in this regard.

  Thank you

  From what I see here, you must have two shift registers, one for each circle you try to draw.  You just update those who need update inside the corresponding event.  Use then Cancatinate string to combine the two images.

  Other things to note:

  Put the terminals of your controls in their case of discipline.  This ensures that you are using the most recent data instead of the outdated data.

  The Stop button event take the changed value.  Yet once, put the terminal inside the event.  This will allow the latch to work its magic.

  Them would like to see photo subVIs RADIUS be I16 instead of DBL.  I recommend that you change your cursors to use representation I16.

  

• Assignment of identifiers automatically or using the value of basic in the rules

  The question is quite simple. I want to order the instances of an entity. How these bodies are classified are of no importance. The problem is that the only information available on instances of the age, which may be one of several bodies and makes impossible to order. Is there any way to assign an identifier automatically apply this ranking, say 0... the number of instances - 1 or is - it possible to use the value of an instance of rules?

  A loop is a bad choice here - a recursive function would end in the same logical dilemma on the tie-break as you you. (If I can offer any advice it would be that the rule loops should be a last choice as a general rule, not a first, they are certainly not as easy to manage as recursive functions in a standard programming language).

  Essentially, you want to work on the price of the ticket (IE an attribute at the level of the entity of ticket):

  the price of the ticket =
  0; If the number of tickets more expensive than me + number of tickets as well as me<= number="" of="" free="">
  nominal value * number of tickets I have to pay for my price/number of tickets, the same value as me; If the number of cheaper tickets than me < number="" of="" free="" tickets="" and="" number="" of="" tickets="" more="" expensive="" than="" me="" +="" number="" of="" tickets="" same="" as="" me=""> number of free tickets
  otherwise the price of the ticket face value =

  where the number of tickets I have to pay for my price = number of cards of the same value that me - (free tickets - number of cheaper tickets than me)

  As I said, you can use alleged relationships to help you work on:
  number of cheaper tickets than me
  and
  number of tickets as well as me

  Published by: Sean Reardon on April 11, 2013 08:35

• Cannot deform stuck HAVE dynamic object using the free transform vector in PS CS6

  Hello

  I stuck a vector object in PS CS6 (13.0.1 x 32) today directly from Illustrator CS6 (16.0.1 x 32) and select 'Paste as smart object' (Windows XP Pro SP3).

  I then tried to distort the object glued using the free transform tool by dragging one of the handles to angle with hold CTRL (Windows).

  General warps\distorts the object, but instead, it launched an operation to bias .

  If I paste as Pixels or shape layer and then apply free Transform, < Ctrl + corner handle slide > performs a warp\distort operation.

  Also, if I have rasterized glued it opposed and then convert them to a smart object, I can warp\distort.

  Is it not possible to paste a vector Illustrator in as a smart object, then warp\distort directly using this technique?

  Thanks for your help.

  Richard

  Your right because on a stuck vehicle a smart cannot deform, false or perform perspective transformations.

  One solution would be to right click on the vector smart object layer in the layers panel and

  Choose Convert to smart object.

  It depends on what is your object, you would probably better quality of a pasted shape or path, but then you will not be able to open the object

  back in illustrator from photoshop.

• Possible to use the XBOX controller as a mouse in Windows 7?

  PC Xbox controller

  I just bought a xbox controller to play games on my laptop, but also use it as a mouse, I basically would like to simply my controller, that throw out there, I can't understand how to set up like this. I installed everything, through calibration and nothing. Please help :/

  If you can't do it with the XBOX controller, then get a Logitech.
  Software from Logitech lets you map each stick thumb to the axis of the mouse.

• 802. 1 x assignment of vlan dynamic based on MAC?

  Hello

  I use Catalyst3750 and authentication widows AD.

  Our customers PC is driving Windows (is not able 802. 1 x) which is connected to the catalyst switch.

  Is it possible to dynamic assignment of that one Vlan based on MAC?

  When possible, we want to do it without help of VMPS.

  and is there any document relating to the foregoing.

  Thank you very much for you help.

  Tomoyuki

  Tomoyuki Hello,

  What Radius server that you use to authenticate your Clients?

  To Secure ACS, you can configure a feature called "MAC-Authentication-Bypass" that accomplishes your needs.

  This feature must be configured on the switch and the Radius Server (which makes the responsibilities of vlan based on the MAC address of the Client)

  An overview of this feature can be found here:

  http://www.Cisco.com/univercd/CC/TD/doc/solution/macauthb.PDF

  I hope this helps.

  Kind regards

  Chris

• How to assign an initial value by using the driaver or traditional?

  Hi all

  the question is quite simple: I use PCI - 6014 with driver OR traditional DAQ (so far). I have a device connected to a set of things to do in order to provide for a grouping, which selects the operating mode. As soon as the device is triggered and I initialize the DIO, I attribute the initial values BD. The problem is that it takes a while (approx. 15 ms) to do, and during this time (between the initialization of the devices and the initial assignment) the combination of output is one level 0, which is highly undesirable because of the specificity of the device. Is it possible to "encode" the initial values of the things to do, so that, as soon as data is turned on, and the line is declared as DO, it automatically receives the pre-defined value?

  Thank you in advance,

  Mike

  Have you read the card? The answer is no.

• Dynamic action using the datePicker in APEX5.0

  I want to use dynamic action with dates in APEX 5.0 picker such that after the selection of start_date and end_date interactive report should display data for the selected date range.

  I first created an interactive report in the APEX and then created a page with date elements pickers.ln my database table, I have a column name time_stamp, who is with the date format varchar2 data type YYYY-MM-DD - HH24:MI:SS.

  Looks like my request for interactive report below:

  Select * from table1 where time_stamp between to_char(to_date(:p1_item,'YYYY-MM-DD-HH24:MI:SS'),'DD-MM-YY') and to_char(to_date(:p2_item,'YYYY-MM-DD-HH24:MI:SS'),'DD-MM-YY')

  (where p1_item and p2_item are the page numbers for the selectors of dates), the 'Mask of Format' attribute for the selectors of dates, I put to JJ-MM-AA. Now, I need to define a dynamic action to run my SQL query of interactive report based on the selected start_date and end_date arguments. I need to know more about the steps to create such dynamic action and look for the detailed steps to what attributes must be defined to achieve this.

  Help, please.

  Thank you

  Mukul

  I did notice that the column time_stamp was varchar2. You can use this query:

  select *
    from table1
  where to_date(time_stamp, 'YYYY-MM-DD-HH24:MI:SS') between to_date(:p1_item, 'DD-MM-YY')
    and to_date(:p2_item, 'DD-MM-YY')
  

  And if you remove it your selectors of dates format mask then you could be simpler:

  select *
    from table1
  where to_date(time_stamp, 'YYYY-MM-DD-HH24:MI:SS') between :p1_item
    and :p2_item
  

  You have need of other attributes.

• Cannot add component Rectangle dynamically by using the task

  Hey all

  I'm new to Java FX and animation in general (try the last FX2 in netbeans) but I think I'm missing something somewhere... According to documentation, it is recommended to use a task to perform the animation and the screen changes. For some reason although my code works very well outside of a task, but when it is placed in a task it stops just at the point where I want to add it to the main AnchorPane... from my controller below class code, where the "mainApplication' is the main AnchorPane. Any ideas? What am I missing or am I misunderstanding? In the end, I want to be able to add a large number of Rectangles dynamically and animate.

  public class MyAppController implements Initializable {
      @FXML 
      private AnchorPane mainApplication;
      @FXML
      void menuItemClicked(ActionEvent event) {
          justDoIt();
      }
      void justDoIt() {
          Task<Void> task = new Task<Void>() {
              @Override
              protected Void call() throws Exception {
                  Rectangle aperture = new Rectangle(10, 10, 250, 250); 
                  aperture.setFill(Color.WHITE);
                  aperture.setVisible(true);
                  System.err.println("Last line executed");        
                  mainApplication.getChildren().add(aperture); 
                  //((Pane)mainApplication.getScene().getRoot()).getChildren().add(aperture); <-- not working either
                  System.err.println("never gets here");
                  return null;
              }
          };
          Thread th = new Thread(task);
          th.setDaemon(true);
          th.start();
      }
     
      @Override
      public void initialize(URL url, ResourceBundle rb) {
      }
  }
  

  The API Animation will take care of the threads for you questions. There is (almost?) never need to work with concurrency API and tasks when working with animations.

  From your description, it seems that the best approach is to create each of the individual animations you need and put it in a SequentialTransition. You can implement the 'gaps' in there with PauseTransitions. Then you can just run the sequential transition button.

  Small example:

  import javafx.animation.Animation.Status;
  import javafx.animation.PauseTransition;
  import javafx.animation.RotateTransition;
  import javafx.animation.SequentialTransition;
  import javafx.animation.Transition;
  import javafx.animation.TranslateTransition;
  import javafx.application.Application;
  import javafx.event.ActionEvent;
  import javafx.event.EventHandler;
  import javafx.scene.Group;
  import javafx.scene.Scene;
  import javafx.scene.control.Button;
  import javafx.scene.layout.BorderPane;
  import javafx.scene.layout.Pane;
  import javafx.scene.paint.Color;
  import javafx.scene.shape.ClosePath;
  import javafx.scene.shape.LineTo;
  import javafx.scene.shape.MoveTo;
  import javafx.scene.shape.Path;
  import javafx.scene.shape.Rectangle;
  import javafx.stage.Stage;
  import javafx.util.Duration;
  //
  public class SequentialAnimationExample extends Application {
  //
      @Override
      public void start(Stage primaryStage) {
          final Rectangle rect = new Rectangle(100, 100, 250, 150);
          rect.setFill(Color.CORNFLOWERBLUE);
          final Path arrow = new Path();
          arrow.setFill(Color.DARKBLUE);
          arrow.getElements().addAll(
                  new MoveTo(150, 150), new LineTo(250, 150),
                  new LineTo(250, 125), new LineTo(300, 175),
                  new LineTo(250, 225), new LineTo(250, 200),
                  new LineTo(150, 200), new ClosePath());
          final Group group = new Group(rect, arrow);
  //
          final TranslateTransition moveRight = new TranslateTransition(Duration.seconds(1), group);
          moveRight.setByX(400);
          final Transition pause = new PauseTransition(Duration.millis(500));
          final RotateTransition turn = new RotateTransition(Duration.millis(500), group);
          turn.setByAngle(90);
          final TranslateTransition moveDown = new TranslateTransition(Duration.seconds(1), group);
          moveDown.setByY(200);
          final TranslateTransition moveLeft = new TranslateTransition(Duration.seconds(1), group);
          moveLeft.setByX(-400);
          final TranslateTransition moveUp = new TranslateTransition(Duration.seconds(1), group);
          moveUp.setByY(-200);
  //
          final SequentialTransition animation = new SequentialTransition(
                  moveRight, pause, turn, pause, moveDown, pause, turn, pause,
                  moveLeft, pause, turn, pause, moveUp, pause, turn);
  //
          final Pane pane = new Pane();
          pane.getChildren().add(group);
  //
          final Button playButton = new Button("Animate!");
          playButton.disableProperty().bind(
                  animation.statusProperty().isEqualTo(Status.RUNNING));
          playButton.setOnAction(new EventHandler() {
              @Override
              public void handle(ActionEvent event) {
                  animation.play();
              }
          });
  //
          final BorderPane root = new BorderPane();
          root.setCenter(pane);
          root.setBottom(playButton);
          final Scene scene = new Scene(root, 850, 650);
          primaryStage.setScene(scene);
          primaryStage.show();
      }
  //
      public static void main(String[] args) {
          launch(args);
      }
  }
  

• Properties of the dynamic component using the EL Expressions

  Hi, first I use JDeveloper 11.1.1.6.

  To better explain my problem, I think the best is to expose my use case.

  So, I have a form with hundreds of components and I have a page before the form to select an option, and depending on the option chosen, different shape components are shown to the user. It's all configured in a DB Table. For example: each record db has the id compoennt and some properties like requires it, people with disabilities, visible, etc. If I want to put a component is not visible, that I just have to call setVisible on component whose value to false. So, so far, no problems, everything works fine.

  But I have another requirement that gives me problems. Some components are dependent on others. Let me give you an example:

  • When I select option A (in the previous menu) the X-component is necessary if the component is set to 1;
  • When I select the option B (in the previous menu) the X-component is necessary if the Z component has a value of 1;

  You are probably thinking, "well, you can do this with EL Expression" and I agree. I can do but so far I couldn't do it directly on the properties of the component. But I want to keep all configs in the comic book (it is easier for the customer keep the components on the form.) Tomorrow, that he might want to change the component that x be required only when W element is set to 1.)

  So my question is, can I ask an EL Expression programatically real estate one component?

  Hi, has solved the problem.

  Leave the solution for future users with the same issue here:

  	String [] partialTriggerComps = r.getRequiredIfComponents () m:System.NET.SocketAddress.ToString (.split(";"));
  	String expression = r.getRequiredIfExpression (m:System.NET.SocketAddress.ToString ());
  	comp.setValueExpression ('compulsory', ADFUtils.getValueExpression (expression, Boolean.class));
  	comp.setPartialTriggers (partialTriggerComps);

• Dynamic action using the box in a table

  Hello

  I'm using version 5.0, apex

  I created a tabular form and a report at the same table on the same page, in tables when I check a record, the report must refresh and display data for the selected record. Need your valuable advice.

  Thank you

  Infantraj

  Hi Infantraj,

  Infantraj wrote:

  Hello

  I'm using version 5.0, apex

  I created a tabular form and a report at the same table on the same page, in tables when I check a record in the form of tables, the report must refresh and display data for the selected record. Need your valuable advice.

  Thank you

  Infantraj

  You mean you want to filter the report in accordance with the selected line in the form of tables.

  1 create a hidden point having a protected value as no. and put it in the where clause of your report query.

  2. in the box click set the value of this hidden element.

  3. refresh the report region (add a real action-> cooling-> region-> Select your area of report.)

  or better to create example on apex.oracle.com and share identification information.

  Kind regards

  Jitendra

• Downloaded CD player and took my XI from Adobe.  I wasn't able to use the domain controller and want to have my back XI.  How can I do this without losing the Adobe?

  @Can you please show me how I can get rid of the DC Adobe and return to my XI.  I can't use this program to DC.

  Margery John Ziemann

  {Removed by hpst phone number]

  Hi margery,

  Uninstall the CD, reboot your system and install Reader 11 using this link Adobe - Adobe Acrobat Reader DC Distribution.

  Kind regards
  Nicos