Assignment problem ASA 5510 AnyConnect static IP address

Similar Questions

• ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone

  Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...

  We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.

  This is the phone that we seek;

  http://www.Cisco.com/en/us/prod/collateral/voicesw/ps6788/phones/ps10499/ps11005/data_sheet_c78-603725.html

  I want to know is the Anyconnect Essentials license will work with these IP phones?

  When I do a version of the show,

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?

  Hi Leo,

  you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»

  ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.

  CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574

  HTH

  Herbert

• Support ASA 5510 Anyconnect

  I see that the latest code for the 5510 is 9.1.5 and they have an end of life of the product. I have 100 Anyconnect premium licenses on a 5510 I've ever used. I was starting to put in place. What are my options now?  Does this mean that I'm having problems with any more recent code as Microsoft 10 and even new versions of Microsoft 7 IE etc?   Oh I forgot trying to turn this 5510 SSL remote access device?  Thank you

  I noticed that I have a 5505 with 25 licenses Anyconnect premium on it (installed by accident by the seller) but this support does not seem to have folklore about that yet.

  The 5510 with ASA 9.1 (5) software is fully capable of supporting AnyConnect (Essentials or Premium-) full-tunnel remote access SSL VPN for users on operating system platforms more modern. It is more the software client AnyConnect himself (compared to the head of network ASA) which sometimes needs to be updated to accommodate the latest operating system compatibility issues.

  In addition, with AnyConnect Premium, you can configure mode clientless SSL VPN and end users simply access the ASA and interact with remote resources through a portal in the browser.

  The 5505 isn't enough end-of-Sales again (the other original of the 5500 series for fall 2013); but we expect a replacement platform soon.

• Cisco ASA 5510 multiple dynamic config VPN L2L necessary

  Hello

  We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?

  Oleg Kobelev

  The config only you need in the ASA is: -.

  (1) set of crypto processing

  (2) political ISAKMP

  (3) dynamic Crypto map

  (4) default group L2L & PSK

  (5) Config RRI (reverse Route Injection)

  HTH >

• Cisco ASA 5510 - restrictions of VPN (AnyConnect) based on the AD user or IP address

  Hello

  I want to test how to restrict access user on an ASA 5510 AnyConnect. In politics, I can define what networks will go through the VPN tunnel and which not (split tunneling). The ASA has a LDAP connection and only AD users with a special security group can connect over AnyConnect.
  On the other hand I would like to restrict access for special users within a VPN policy.

  So my question:
  What are your recommendations to implement this szenario?

  My two ideas would be:
  1. the access rules based on the user of the AD.
  2. special reserve IP addresses in the pool of addresses AnyConnect for some users, so I can limit access to the normal firewall rules base based on the source IP address.

  What are your recommendations and is it possible to realize my ideas (and how)?

  Thanks in advance

  Best regards

  Hello

  I will suggest that you configure a second ad group in the server and another group strategy in the ASA, you can configure certain access on each group policy "the installer of the filters, assign different split political tunnel, different ACL' and in the ad server, you can assign users for example to the AD Group A and AD Group B based on the access you want to give them now , you must configure LDAP mapping to assign the user specific group policy that you want based on the AD group that they belong.

  You can follow this documentation that will help you configure the LDAP Mapping:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Best regards, please rate.

• Assign the static IP address by ISE, ASA VPN clients

  We will integrate the remote access ASA VPN service with a new 1.2 ISE.

  Authentication is performed in Active directory. After authentication, can address assigned to a specific user of VPN by ISE IP?

  This means that the same VPN user will always get the same IP address. Thank you.

  Daniel,

  You can override the IETF-RADIUS-Framed-IP-Address in the authorization policy.

  However if I may make a suggestion:

  Unless you have only a handful of users to do so, it may be appropriate to assign the address of ISE pool or perform the mapping of LDAP attributes on ASA itself.

  In the latter case, the IP addresses are kept on the server as LDAP attributes and ASA will map the IP address. You don't want to keep address IP DB in several places.

  M.

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon

• static IP address assignment to TiVo on BEFSR41 router

  Hello

  I'm trying to put in place a couple of TiVo cable already on my home network so I can 'see' on my Mac using the TiVo Express of Toast Titanium function and copy the TiVo on my Mac programs.   TiVo technical support suggested that the problem is that my Mac IP address is 198.162.1.100 (assigned automatically) and for some reason some of my TiVo is on 198.162.0.2 et.0.3.  They suggested that I have manually assign a static IP address for the for put them in 'sync' with my Mac address - that is to say, something in the range 198.152.1.xxx of TiVo.

  I was able to assign a static IP address of 198.162.1.109 to the head of the TiVo (and my Mac is still not see it), but I received an error message when I tried to assign 198.162.1.110 to the other TiVo.   Technical support suggested I check with you on assignment of the IP address via the router.  Can you tell me if this is possible and if so, how?

  Thank you!

  If the TiVo is Gets an IP 192.168.0.2 or similar when using dynamic/DHCP/Auto IP addresses means the TiVo is connected to a different router or get an IP address from another DHCP server.

  1. Please check your wiring. Your modem should connect to the internet, the port of the BEF everything is connected to the BEF. If the modem has additional LAN ports, a modem/router combo device. Do not use additional ports on the modem/router combo.

  2. If wiring is OK, as previously indicated another reason for a 192.168.0.2 automatic address IP sharing a computer inside your network that has been configured for an internet connection. With internet connection sharing you can share an internet connection through this computer. To do this, the computer will assign 192.168.0. * IP addresses on its side LAN. Please check your computers if there is one that has internet connection sharing enabled.

• Cisco Anyconnect/WebVPN license for ASA 5510

  Hello

  Someone could please check the licenses for ASA 5510 attachment and let me know. We currently have ASA 5510 with basic license. According to the table attached under VPN sessions, he mentions that "250 combined SESSIONS IPSec and WebVPN" and to "Max box of WebVPN Session" it is mentioned that 2nd meeting, exceeding that we must buy license optional webvpn. While we the 250 combined license for IPSec and webVPN. We must purchase additional anyconnect license to set up remote access for users who want to use the internal resources from outside the network. OrElse, we don't have to purchase license and can configure webvpn/anyconnect of existing combined license existing users basic ASA license? Waiting for your response. Thank you.

  You are welcome.

  1 Yes

  2 AnyConnect requires no Java, but it can he use when connecting to one AnyConnect SSL VPN client and launch the Web browser option start Java-based. There was a bug with the AnyConnect old versions had later who should have addresses. You also have the option to launch via IE and using ActiveX or simply throw AnyConnect directly - neither of these two methods require Java.

  Here is a document TAC on the Java questions if you want more details.

  Please take a moment to note the useful messages and mark your answers questions.

• ASA 5510 IPSEC VPN connection problem

  Hello

  We have an ASA 5510 (ASA version 8.0) of remote access VPN configured and works most of the time, but there is a problem when you have more than one client that connects to the same office remotely.  When the first VPN client is connected to the remote desktop, everything works fine, but when the second client connects to the VPN, it connects fine but do not get any traffice return to customer.  I can see under monitor-> statistical VPN-> Sessions-> remote access-> Rx Bytes is 0. Both connections are from the same public IP address of the remote desktop.  I changed some settings on NAT - T and a few other things, but without success.

  Could someone help me please how to fix this?

  Thank you very much.

  Make sure that customers use because that probably her you're not. (default value is NAT - T).

  Federico.

• Static IP address assignment to a device? (An XBox)

  I'm trying to set up my XBox One to broadcast remote but I am completely ignorant when it comes to networking and rely the economy on the default settings. There seem to be three main parts to this process described here:

  - Port forwarding (which was explained by DexterJB. (Thank you!)

  -Allocating an address static IP to the device (This step)

  - and implementation of dynamic DNS

  I was wondering if someone would be willing to walk me through step of assigning a static IP address to a device, which in this case is my XBox One.

  I really wanted to know that for a while for other devices, but do not know if it is a thing of router or a computer thing. I'd appreciate any help.

  Hi @varxtis,

  You are welcome!

  Instead of setting a static IP address for your XBOX, you can make a reservation address so that the XBOX will have a compatible IP for port forwarding you have done. You can refer to the link below for the steps on how to do it.

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24091

  Kind regards

  Dexter

  The community team

• Tutorial: Can't stay connected via WifI? Try to assign a static IP address.

  
  

  Very often, people have problems with their wireless routers give up connection to their HP printers. With the help of the video above should help you set up a static IP address that can solve this problem.

• ACS 5.3 assign static IP address according to authenticated user

  In fact, I have a lab with ACS 5.3 running with 802. 1 x, but when when the user is successfully authenticated, it is assigned and the address IP of the DHCP server, is it possible to assign a static IP address function connection username?

  Kind regards

  Juan Carlos Arias

  Hello

  It would be for external database users like AD or LDAP? Or would it be possible for internal auditors ACS?

  Kind regards.

• Remote VPN on ASA5510 - get static IP address of ASA

  Hi all

  Please, I have configured a remote VPN on cisco ASA 5520 and everythings seems to work very well... DHCP IP have been renting to users who connect to the VPN. but the question is now that our customers want a static IP address to give to a particular user when it connect via VPN.

  is this possible?

  Hello

  You can configure a static IP address in a configuration of "username" users on the SAA. Of course, I want to say that you need to do the LOCAL on the SAA authentication itself for users VPN to use this command

  For example

  user testuser password testpassword privilege 0 name

  user testuser name attributes

  VPN-framed-ip-address 10.10.10.2 255.255.255.0

  This should make the same IP address in the user always

  Hope this helps

  -Jouni

• AnyConnect VPN license on ASA 5510

  Hello

  We have ASA 5510 IPS with basic license. We must now Anyconnect support for more than 2 users.

  Anyconnect (tunnel mode) but essentially Anyconnect license enough? Do need me a license for SSL VPN peers?

  What about Anyconnect without customer, I see that I need a premium license?

  This one is pretty ASA5510-SSL50-K9? It's really expensive compared the Anyconnect Essentials.

  Here is my worm out sh:

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 50
  Internal hosts: unlimited
  Failover: disabled
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 0
  GTP/GPRS: disabled
  SSL VPN peers: 2
  The VPN peers total: 250
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes a basic license.

  Yes, AnyConnect Premium includes all the SSL features (including the complete tunnel mode AnyConnect - which is what sustains essential AnyConnect).

  So if you buy the 50 user for AnyConnect Premium license, you can have up to 50 SSL VPN connections, if they are the combination of all without customer, or combination of tunnel without customer and full, or just full tunnel. All with a maximum of 50 simultaneous SSL tunnels.