Average data acquisition alternating window 25sec

Similar Questions

• Pavilion TS 17-g099nr: PCI Data Acquisition and processing of the Signal Windows 10 x 64 controller driver

  Hi, it is impossible for the moment to install the driver for PCI Data Acquisition and Signal Processing.

  I downloaded the driver from Intel, and it did not work... I found a version of this site for windows 8.1 unupdated and it does not work.

  A little help?

  Thank you!

  Hello:

  It could be one of two different drivers.

  Try this one first, and then restart the PC.

  This package contains the Intel Chipset Installation utility. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75561.exe

  If this does not work, try this one...

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the thermal protection of the system to work properly. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75506.exe

• How to run a window of data acquisition and another pane at the same time

  Hello

  I have a main window for data acquisition and in front panel there are four Sub Vi. When the main window of data acquisition is running and at the same time if I run the Subvi - main window stops data acquisition and the secondary window starts to run. But I want to launch the window of acquisition of primary data and the pane at the same time. Please give me a solution for this...

  Thanking in advance.

  Nikhil

  Hi Nikhil,

  My explanation has answered your question. Take a look at the image as an attachment. Let us know if you have any other questions.

• Data acquisition inherited Configuration MAX window

  I have LabVIEW 7.1, and Max under the software it shows v8.8 NOR-DAQmx and v7.4.4 NOR-traditional DAQ. When I am developing devices and Interfaces, only from the devices listed OR-DAQmx ppears with the DAQ card (PCI-6221: "Dev1"). The VI I need to ru uses the traditioal DAQ. When I run the VI I get an error message that the jury must be configured. How can I get traditional DAQ to apear in the devices and Interfaces fall down, so I can set the jury? The VI is not easily updated to DAQmx.

  Thanks for any advice.

  Paul

  Hi Paul,.

  The PCI-6221 is a M-series card.  M-series cards have no traditional DAQ driver support.

  Major differences between series E and M series data acquisition devices

• HP laptop - 15-r224tx: PCI controller of Data Acquisition and processing for HP for laptop - 15-r224tx

  I get upgraded my laptop (HP for laptop - 15-r224tx) for Windows 10 but I can't find the driver for the controller of PCI Data Acquisition and Signal Processing. Please help me find the right one.

  Thank you!

  You are the very welcome.

  It is the latest version of the W10 driver for this card model... see if this solves the problem, if you have not already installed this driver.

  This package contains the installation package driver for the controller wireless LAN Realtek RTL8723BE/RTL8188EE in the laptop models running a supported operating system.

  File name: sp72517.exe

• Z600 Workstation: workstation Z600 missing of pci data acquisition and signal processing controller driver

  I just installed Win7 Pro x 86 on my Z600 workstation.  It was an upgrade to Windows XP Pro.  I'm missing the driver for PCI Data Acquisition and processing of the Signal and Hardlock USB 1.02 controller in Device Manager.  Can someone help me find these drivers.  I looked on the page of Support/Drivers for this model, but could not find anything.

  Hello

  You can get assistance on the HP Enterprise Business Forum since you have a professional worktsation.

• HP 240 G4-328TX: need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Hello

  Need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Can anyone provide me please the link for download it for windows 10

  Thank you

  Hello:

  See if this driver works...

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7609938 & swItemId = ob_153701_1 & swEnvOid = 4192

• 15 - ac122tu: PCI of Data Acquisition and the controller driver of laptop HP 15-ac122TU signal processing

  Hi team,

  I just install windows 7 edition integral and peripheral Bluetooth windows 8.1 is not be detectable, when I search for problem that I came across this PCI data acquisition and Signal Processing controller driver is missing and a unknown device driver missing shownup in my result of troubleshooting. Please help me

  Please find the screenshot for your reference

  Thank you

  

  Hello:

  See if these drivers work...

  CQI PCI controller:

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the heat of the system
  protection to work properly. This package is provided for the laptop models running a supported operating system.

  File name: sp71638.exe

  Bluetooth:

  This package contains the installation package driver for Realtek bluetooth in the laptop models running a supported operating system.

  File name: sp71288.exe

  Unknown dev:

  This package provides the HP 3D DriveGuard software (HP ProtectSmart Hard Drive Protection) for the laptop models running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

  File name: sp71811.exe

• DSA maxing out CPU data acquisition

  I'm developing an application on a PXI-8196 (Windows XP) controller that uses a card PXI - 4472 DSA to read a single microphone and a FFT signal analysis. I need solve the two frequencies of 36kHz (and), so I've planned for sampling 96 kech. / s. I wrote a simple loop of data acquisition, configuring NI44xx DAQ/read screws using read the string unique at this rate, but when I run it, it immediately pegs my CPU 100% usage. So far, I did have problems with missing samples or the system crashes, but I am a little concerned that only data acquisition uses all my CPU time. Y at - it tricks that I can implement to reduce the CPU load?

  I tried to vary the parameter samples per channel - with sizes ranging from 1000 to 48000 samples - buffer but I do not seem likely to reduce the CPU usage. Changing the sampling frequency affects the CPU usage (up to about 40% to 48 ksps / s; ~ 75% 72 ksps / s), though. According to this KB: http://digital.ni.com/public.nsf/allkb/D9DDF9FA02D1C18A86256EBC0016C93D

  "A controller Embedded PXI-8176 can compute all the time of the spectra of FFT power on 8 channels for PXI-4472 clocked at 102.4 ksps / s »

  so I think with my 8196 I should have no problem at all to read only one channel 96 kech. / s.

  Anyone have any suggestions to reduce my CPU Overload? Thank you!

  Here is a link to some good information on how to OR-DAQmx 7.4 and later behaves with respect to the use of the processor: Default CPU use with NOR-DAQmx Version 7.4

• HP laptop - 15-ac022ne: pci of data acquisition and signal processing controller

  I have this laptop HP - 15-ac022ne and I got windows 8, evrything has not been totally perfect until I upgraded to windows 10, wireless function no longer works, tried to install the driver and update, it was succsessfully installed in the machine to say, but still not working and PCI data acquisition and signal processing controller driver is missing tried to download the chip set on the driver support page, does not, tried to update the driver through the Device Manager and the message can not find a driver for the device of said...

  Please I need help...

  Hello:

  You need this driver for pci data acquisition and signal processing controller.

  FTP://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72069.exe

• SCXI and acquisition with Windows 7 x 64

  Our just updated IT to update our phones and we have received Windows 7 x 64.

  Data acquisition, we use the SCXI hardware in the SCXI-1000DC chassis and an acquisition of data SCXI-1600 USB card.  Doing my gear OR set up on the new laptop, I discovered that neither does not support Windows 7 x 64 for the SCXI-1600. The other options to connect the SCXI-1000 chassis to a laptop are the DAQcard-6062E and DAQcard-6036E, nor which supports Windows 7 x 64.  According to the information below, there are no plans to support x 64.

  What are my options to continue the use of the material, we have invested with the laptop running Windows 7 x 64?

  You will need the NI SCXI-1349 connection block and SH68-68-EP cable.  The SCXI-1349 plug at the rear of your SCXI module and cable connects the 1349 the USB device series M mass termination.  The rest of the configuration is identical to any PCI/PXI E Series device.  The USB M Series device will be the analog-to-digital converter for the system instead of the SCXI-1600.

• LeCroy Waverunner 640Zi - Data Acquisition

  Hello... I'm trying to set up my oscilloscope waverunner with LabVIEW SignalExpress for data acquisition.

  I took the steps so far:

  1 pulse generator hooked to scope of signal generation

  2 USB scope to the installed computer with LabView

  3 downloaded lecroyscope driver 3.2.9 - x 64

  I turn on the scope and plug in the USB to the computer and SignalExpress begins.

  a. start by using data acquisition

  b. Add step/aquire signal / IVI aquire / IVI brought aquire

  c. create new IVI session... resources descriptor (I choose my USB device ' USB0::0x05FF:0 x 1023: 2812N61507:INSTR '), I select the right driver (lcscope), and I do not click enable simulation data, press ok
  d. I still receive configuration errors

  e. did the research... some forum said goto MAX, find drivers and uncheck the Cache and the exchange of check

  f. attempt to initialize... always get config errors.

  g. return to MAX... change to simulate with specific driver.

  h. initialization works... NO errors, BUT no data are acquired.

  Help, please!

  Hello

  Sorry to jump in if I was out of the country for a while and am still catching things in my office.

  I think you are looking for someone to say yes, "you can connect to the scope with NOR-MAX and VISA, and here's how interactive tool do"

  A few things:

  LabVIEW for XStream extended driver is the right one.  It works with all the TeledyneLeCroy Windows based scopes.

  As I see has already been noted. (I'll give Kudos soon), the scope of application must be configured to use interface USBTMC.  To do this, go to the drop down Utitlites on the scope menu and select "utilities configuration... '. "in the tabs that appear at the bottom of the screen, select the 'Remote' tab and make sure that the interface type is set to USBTMC.  This will also show you the VISA resource (I see it in the title of the image of VISA interactive tool indicated in a previous post).

  Once this field is selected, the PC should detect the USB connection and install the device. (you can see in your device manager as a Test of USB and the measurement device):

  

  Once this is done, you can then enter the NOT-MAX and it will detect and display resources.  You can now communicate with the device:

  

  If you have problems, do not hesitate to give me a call and I'm happy to walk through it over the phone.

  Kind regards

  Leonard Brown
  Technical sales engineer
  Teledyne LeCroy
  1-800-553-2769

• EliteBook 850 G3: Impossible to install PCI Data Acquisition and processing of Signal or PCI memory controller controller

  Hello

  I just got a new Elitebook 850 G3, it came with a windows 7 x 64 bit CD and App/drivers installation disk, as well as the 8.1 and 10. I was able to update/install all drivers, but PCI Data Acquisition and Signal Processing controller and PCI memory controller. I tried to go to the HP Web site for my product, only 8.1 and 10 x 64 operating system options, a search on the entire SWSETUP folder finds nothing and allowing research on windows update returns no result. I tried the 8.1 drivers, obviously no support for operating system, but wanted to try. Also tried to use the G2 850 drivers with no luck. Has anyone experience this problem? HP has drivers for these 2 devices for Windows 7 x 64? Any help is greatly appreciated!

  I can't seem to find a driver with the hardware ID you posted.

  If I missed something in one of the folders, see if this driver works...

  FTP://ftp.HP.com/pub/SoftPaq/sp73001-73500/sp73137.exe

• Problem of reliability data acquisition PXI-4071

  Hello

  I'm having a problem of reliability using my 4071 Pxi digitizer mode.

  I have a number of tests that use the SMU-6363 (usually configured for DC) analog output to provide a stimulus for our own device, which has a number of a/d converters.  We use the PXI system for calibration and testing.

  1. I select a voltage ranging from tensions.

  2. program the PXI-6363 to drive this tension

  3 TIME about 10ms to settle.  Note there no discrete capacitors or resistors in the circuit.  Everything is parasitic and would generally be under the nF mark and less than 10 ohms

  3. configure and Initiate() acquisition of data with the PXI-4071.  In general, I use a sample rate of 1000 s/s and get about 30 samples (worth 30 ms).  Activation is immediate and I used the default a queue time, 0, set the time and it doesn't seem to make a difference.

  4. measure the voltage with the CDA.  For debugging purposes I have sometimes made twice once before calling Initiate() and once after.  The after is normal.  The time required to measure the ADC is shorter than the acquisition time, but regardless of stimulation by the SMU-6363 is constant

  5. extract the waveform.

  6. the average waveform and compare the value of ADC measured by applying tolerances etc.

  Here's the problem: it works well most of the time.  But only 0.1% of the time (1 on an acquisition of 1000), I get 8-12 samples that are close to 0.   It sounds like a problem of time settling (on the surface), but no matter the amount of wait time data, I always get this behavior.  Not only that, but the tension before the call to Initiate() in height CDA, it always confirms that the motor voltage is already set to the programmed value.  Nevertheless the acquisition presents near data 0.

  So far our independent ADC always reports the expected before and during acquisition (100%) voltage.   It's like the DMM input is disconnected during the acquisition during a period of time, because we have confirmed that the voltage is already present prior to the acquisition (component can).   I have no errors the insider or FetchWaveForm calls.  I still have all my samples.  And 99.9% of the time that everything works as expected.

  The DMM and ADC are connected to the same point and both are referenced to ground, and as I said before only the parasitic capacitance and resistance (cable).  We use a matrix of switching (PXI-2530 (b) to make these connections.  We almost always use 51/2 digits and 10V range for data acquisition.

  Hello

  I thought about it and was going to repost but am distracted.

  The device with the ADC also has a mux and switches the mux to an internal node.   It only switches when measuring and is open at other times.   There is a race condition where the acquisition starts too early and maintains the acquisition after that the switch is open.   Unfortunately I don't have the option to trigger.

  I forgot the internal mux that I had designed the test years ago and I did some updates to improve the stability of the test.    That's why we start the ADC measurement when acquiring.

  I just added a routine to reject samples below a threshold

• Why data acquisition in an executable collect fewer samples?

  Hello

  I have LV2012 on Windows and SMU-6341 map in PXI chassis.

  I have a task for the acquisition of data on I-1 on my monstrous application. Well, to get to the point, I have here a case where the task of data acquisition starts, waiting 20ms, reads all available samples and puts an end to the task. For the parameters see the piece attached. Then, the collected data is plotted on a waveform graph. Usually about 200 samples are taken in the case of data acquisition. Then loops shown sequence, until certain conditions are met.

  Unfortunately a problem occurs when I deploy a rack application (exe) on a production PC some 600 miles away from me.

  This is an example of what I get on my development PC (LV and runtime give similar results):

  

  This is an example of what I get on the production of exe PC (13 iterations, bad luck ):

  

  It totally looks like the data acquisition task mentioned seizes one sample to an iteration of the loop.

  I enclose a noodle dragged out of the main program. I'm about to test the version of this noodle on the production of PC in a few hours, but I would like to hear all the ideas that emerge.

  Thanks in advance!

  cubz wrote: from my experience, the continuous 'Samples' mode does not stop when the buffer is full. The loop of 4 seconds (with 10 k samples/s in the sample buffer 40 k)-that is to say samples how finished works IMO.

  If the buffer is filled in continuous mode of the samples, you will get an error.  I'm sure it's something you don't want.  In this example, you have provided, you really should have finished samples and has said the acquisition of data to read samples of N.  It is the only way to ensure you get all the data you want.

  In regards to your differences between development and executable, the executable file tends to only not nearly as happening (Debug stuff for the most part), so it tends to run faster.  If you're depending on a software clock, anything can happen (having a ton of little or no data).  That is why we say you use the clock machine and get the number of samples that you actually want.