Base station changes from green to orange

Similar Questions

• "Home CPU/memory/connection" (host) changes from green to gray, then gray to green?

  Hey everybody,

  I'm trying to track down a problem with one of my two hosts. My Cluster (2 guests in HA/vMotion) is pretty basic, but runs a lot of VM that requires an availability of 100% (as if we want to accept less ). This is the result I get every two weeks. It's a bit concerning to know that for some reason a node is abandoned, or is it same stall? I see no vMotion alerts or the tasks in that time. Nothing seems to break. Uptime on each virtual computer and the node in question leads me to believe that nothing is really wrong, but it can be worse than what I think. I mean he's only 17 seconds... how bad could it be, right?

  I'm assuming "Host memory usage", "host CPU usage", 'Swap host service rate console', etc. go from green to gray, then gray green means that it is not a resource problem, just an indicator that it is "grayed out" because there no report or an interruption of the connection.

  I guess I am wondering if it is network related, associated hardware partner, vsphere host or something I can't even think. The host disconnects for 7 seconds and no quick vMotioning can't. I think 30 seconds is the rule in front of him vMotions? I mean, I had rather not vMotion, if I can avoid it.

  Whatever it is, what do you think?

  Alarm 'Hosting service console swap rate' on (HOSTNAME) changed from grey to green
  Info
  06/07/2011 19:53:35
  (HOSTNAME)

  Alarm "Host memory using" on (HOSTNAME) changed from grey to green
  Info
  06/07/2011 19:53:35
  (HOSTNAME)

  'Use of the UC to host' alarm on (HOSTNAME) changed from grey to green
  Info
  06/07/2011 19:53:35
  (HOSTNAME)

  Alarm 'Host fell' on (HOSTNAME) sent by e-mail to (ADDRESS);
  Info
  06/07/2011 19:53:26
  (HOSTNAME)

  Alarm 'Host fell' on (HOSTNAME) triggered an action
  Info
  06/07/2011 19:53:26
  (HOSTNAME)

  'Host fell' alarm on (HOSTNAME) has changed from yellow to green
  Info
  06/07/2011 19:53:26
  (HOSTNAME)

  Alarm 'Connection and power supply home State' on (HOSTNAME) changed from red to green
  Info
  06/07/2011 19:53:26
  (HOSTNAME)

  A connection established
  Info
  06/07/2011 19:53:25
  (HOSTNAME)

  A connection established
  Info
  06/07/2011 19:53:25
  (HOSTNAME)

  Alarm 'Connection and power host State' on (HOSTNAME) sent by e-mail to (ADDRESS);
  Info
  06/07/2011 19:53:20
  (HOSTNAME)

  "Failed to connect to host" alarm: sent an SNMP trap for the entity (HOSTNAME)
  Info
  06/07/2011 19:53:20
  (HOSTNAME)

  'The host connection failure' on (HOSTNAME) alarm action
  Info
  06/07/2011 19:53:20
  (HOSTNAME)

  "The host connection failure" alarm on (HOSTNAME) changed from gray to gray
  Info
  06/07/2011 19:53:20
  (HOSTNAME)

  'Hosting service console swap rate' alarm on (HOSTNAME) changes from green to grey
  Info
  06/07/2011 19:53:19
  (HOSTNAME)

  Alarm "Host memory using" on (HOSTNAME) changes from green to grey
  Info
  06/07/2011 19:53:19
  (HOSTNAME)

  'Use of the UC to host' alarm on (HOSTNAME) changes from green to grey
  Info
  06/07/2011 19:53:19
  (HOSTNAME)

  Alarm 'Host fell' on (HOSTNAME) changes from green to yellow
  Info
  06/07/2011 19:53:19

  
  (HOSTNAME)

  'Connection and power host State' on (HOSTNAME) alarm action
  Info
  06/07/2011 19:53:19
  (HOSTNAME)

  Alarm 'Connection and power supply home State' on (HOSTNAME) goes from green to red
  Info
  06/07/2011 19:53:19
  (HOSTNAME)

  Host is not responding
  error
  06/07/2011 19:53:18
  (HOSTNAME)

  My memory, I cannot keep records for a long time. Last year, I think that I have seen this problem and it was a bug. There is also a patch for it. It was a BUG where the way every now and then, the confidence in me it was no problem at all in the perspective of the environment.

  I don't remember the article or the revision of patch has this connection, but you may need to check the kb.vmware.com to see if you can find.

• All my Airport extended expresses abandoned their Wi - Fi connection to my base station can the airport extreme.  In other words, the light goes from green to yellow flashing and I can't reconnect.  All ideas

  All my express airport extended (one for music, one for the printer and one to extend range) lost their connection at the same time.  In other words, they all went from green to yellow flashing.  I was not able to reconnect.  Any ideas on how to solve this problem?

  Your first step is always power off the entire network... what... and then restart in good order.

  Modem... Wait 2 min

  Main router... Wait 2 min

  Extenders... Wait 2 minutes.

  Printer and other clients... wait that see everything toward the top.

  If this fails, then you need to find how the network is down... Connect the modem to the computer by ethernet... didn't you internet... If Yes... then try to the main router... If so, try again the next step... When you find the scene of the breakdown, reset it to factory and redo the configuration.

• How can I change the base station Airport of NAT mode?

  I'm trying to set up an Airport base station and stuck because I have the following message is displayed, but no idea how do what he asks...

  Status is showing as Double NAT and then asking me to move on to the base station in bridge DHCP/NAT mode.

  But where do I do this?

  Thank you

  It can be difficult to get the router to bridge sometimes... but if all goes well... Click on the airport icon in airport utility and then click on edit.

  

  Go to the network tab and change DHCP and NAT to bridge.

  

  Click Update at the bottom of the page... Then, everything should be good.

  If you are having problems follow these steps.

  Reset factory airport and then do a manual installation. I recommend that you connect with ethernet which is much more reliable, but your MBPr is not the most important network port that exists... Although there is a bolt of lightning at low cost for the ethernet card.

• Name of the mn500 base station wireless network (be) changed to MSHOME.

  Run a wireless network with the mn500 smooth base station for years.   Last Saturday the network name is MSHOME.  Any thoughts on what is happening or how to change back the name I assigned it?

  Sorry, I misunderstood.  You are referring to the name wireless ID SSID (Service Set).  It is defined in the configuration of your wireless router.  I'm not familiar with this particular router, but with most routers, you can use a web browser to connect to the router (your model, it is http://192.168.2.1) preference of a wired connection that to change the SSID will cause a disconnect wireless, connect you with password "admin" (unless it's been changed) and change the settings.  On most routers, hold the button Reset on the router will return to factory settings which is possible as to how this change could occur.  Links to the user guide and manual configuration is on this page:

  "The Microsoft Home Networking product documentation"
    <>http://support.Microsoft.com/kb/902461 >

  HTH,
  JW

• For some reason, the tab 'Base' is missing from my file to develop trying to change using LR5... ? Help, please

  For some reason, the tab 'Base' is missing from my file to develop trying to change using LR5... ? Help, please

  Right-click (Cmd-click Mac) on another connector for Panel as "tone curve". Make sure there is a check mark for Basic as all other sections of the Panel you want to display.

• Connection printer HP AirPrint from Apple extreme base station.

  Hi, I had a "wps pin code" generated printer to enter my network extreme apple but cannot find where it enter. Use "airport utility" and selecting my extreme and then enter my password of network that I was expecting to see a secondary to the title of "base station" menu where I can enter a wps PIN, but nothing shows up?

  If the AirPort Utility is obsolete, please update in the App Store or download the last update on the Apple Support site. Then launch the application and follow the instructions of his help under the topic "add a printer to your network.

• I have the network wireless with an extreme airport using my base station that dessert 4 Airport expresses. I want to replace the base station with a time capsule from apple.  Are there specific instructions other that connect the new time capsule

  I have a wired to the internet using my base station for 4 expresses the hard extreme airport.  I want to replace the base station with a time capsule.

  It is also easy to replace the existing base station and adding the name of the network and the password?

  You should be able to transfer your configuration of your current access point to new, and then you would just set up the internal drive, try to look at these articles:

  ith-new http://www.TechRepublic.com/article/apples-Airport-extreme-out-with-the-old-in-w.

  -one-airport-extreme-or-time-capsule-to-http://www.iclarified.com/31189/How-to-Transfer-Your-configuration-settings-fromanother

• AirPort Extreme Base Station 4th Gen

  Hi all

  I have an AirPort Extreme Base Station renovated 4th Gen router connected to a modem Arris SB6141 cable.  I had this AEBS for almost 5 years with no problems.  Last night, we had severe weather in the region and almost immediately after a lightning strike extremely close, our internet came out.  Service was also restored and our modem works properly.  However the AEBS is orange with intermittent flashing green.  When I opened the AirPort Utility to diagnose and fix the problem, I was prompted to connect the Ethernet cable to the AEBS.  All cables/cords are connected and secure.  I cycled power on all equipment, tried different cables and even performed a hard reset on the AEBS, and again, it won't recognize the cable Ethernet is plugged.  Any help would be greatly appreciated.

  I guess you have tried another Ethernet cable between the modem and AirPort Extreme... and if this is the case, the storm produced a wave that damaged the port WAN on AirPort Extreme... even if the modem cannot have been hit.

  All you can do is try a Factory default Reset on the AirPort Extreme several times to see if that could help. Good luck!

• Base station disappeared after creating the guest network

  After you activate a burst network 2 things happened:

  (1) my original network is always visible, but you can not connect and it does not work.

  (2) all devices of the airport, including the base station have disappeared from the Airport utility.

  I can connect to the network invited near the base unit as expected. As all devices have green LEDs. However, I can't on the main network. And I can't do anything to solve that devices are not visible in the Airport utility.

  Help!

  The 'main' and 'guest' characteristic of network work properly If the right type of modem is used to enable these services.  That would mean a simple modem, as in the example you see just below:

  

  The main and guest feature will not work properly if you have a modem/router, also known as a gateway, as in the example below, which is the type of device that has a number of ISPs providing to their customers.

  

  
  

  Therefore, the first troubleshooting question here would be.. .what type of "modem" you?

  If you don't know what kind of modem you have, please post back with the number of brand and model of the device that you call your modem. (Please do not distribute private information, such as a serial number).

  Next question... base stations AirPort how do you have?

  Finally... to fix things, it may be necessary to connect your Mac directly to each base station by using a wired Ethernet cable... Since Wireless will not provide access to the settings on the airport using AirPort Utility if things are messy. Your Mac has an Ethernet port?

• I have my time capsule for base station; How do I set up just for Time Machine?

  For several years, I have used Time Capsule as a wireless base station more backup Time Machine. I back up a Macbook Air (single user) and iMac with 2 users (two computers running on OS X 11.5). With Comcast Xfinity I need is more like a base station. In fact, I reset my router Xfinity name and password to replicate what was the name and the password to my Time Capsule network. But, now that it's done I can't understand of set up time capsule without set it up as a base station. The installation guide seems to suggest that I could do so by plugging the ethernet cable from the modem to an ethernet port which is not the WAN port. But this configuration did not work. The installation wizard only took me the steps to set up a wireless network. How can I simply we it with Time Machine as an external hard drive?

  The installation wizard only took me the steps to set up a wireless network. How can I simply we it with Time Machine as an external hard drive?

  Simply turn off the time Capsule wireless.

  To do... Open AirPort Utility, click on the Time Capsule, then click on modify in the window that appears

  Click on the Wireless tab at the top of the next window

  Change the setting for the Mode of network on 'Off '.

  Click Update to save the changes

  

  But... and this is a big BUT... This work of pourrait ... and maybe not. Even if the backup on the Comcast network seems to be working, there will be no help from Apple in case of questions or problems of backup.

  The reason is that, so that your Time Machine backups be supported officially by Apple, users must save on the Time Capsule wireless, or connect their Mac (s) directly to one of the three ports LAN <>- on the Time Capsule using a wired Ethernet cable connection.

  If you decide to try the method of failure to load, please let us know how things work after a few days.

• Should I buy a Base Station for my Apple products to use Time Machine?

  Should I buy a Base Station for my Apple products? I have a Netgear CG3000D-RG gateway and also use Windows with this modem/router. I'm not able to backup using time machine and bought an external hard drive PassPort but I find it pretty annoying having to plug it in to my MBP whenever I want to do a backup. I would like to use the most convenient airport on my MBP feature, however, it seems pointless unless I have connected to my Netgear router/Modem base station. If I have to buy a base station to make the backup of my MBP easier? I also use 6s and iPad Air iPhone. I would be able to save these features too? Thank you!

  1. you must either have a Time Capsule or connect the drive to your computer when you perform a backup.

  2. Time Machine isn't back from iOS devices directly; they should be stored on a computer and the computer saved Time machine.

  (144712)

• Using the base station airport ONLY as a backup, but is not a router

  Hi, I have a simple question that I can't find an answer. I want to use my Airport only base like a time capsule, and not as a wifi hotspot. I'm in a wfi environment that does not have any router, my wifi just to join a wireless network in my office environment. Previously, I worked in an office where I ran a cable DHCP in my airport base station and then he joined with wifi. Now, I just want to use the airport as a backup. Answers to this question involve disable wifi from the airport and hit an ethernet cable from the router to the airport base station. I do not have a router. So is it possible that I can get the device from the airport, make back ups wireless, all at the same time be connected to a wireless network? I'm guessing that the answer is no.

  Unfortunately, your proposal of "no" is correct.

  However, you could configure the airport Time Capsule (ATC) to create a wireless network (without Internet access) and save on the Time Capsule wireless.

  Of course, to do this, when you want to save, you need to log on to your 'normal' wireless network and connect wireless provided by ATC.  Once the backup is complete, then you'll need to sign the CTA wireless and log on to your normal wireless network.

  All things considered, it would be much easier to invest in a USB low price and connect the HDD directly on your Mac. In this way, you can stay connected to your wireless network normal and backups occur automatically.

• How to reconfigure wireless network extended with several base stations

  I have a wifi network in an Airport Extreme wired to the modem from our Internet service provider and an Airport Express Terminal extended wireless in another part of the House. I recently added a second Airport Extreme (also extended wireless) to boost coverage in another area of the House. I want to have the Express and the extreme second each wireless connection directly to the base station to the modem to have the shortest path to the main base station, but the Airport utility network diagram seems to keep showing the network of linearly (main Extreme base - second extreme - Express). So, two questions: first, represents the schema of utility Airport the signal path real (linear Express by Extreme II, then to Extreme II/modem)?  And secondly, if so, how to reconfigure the network to have both Express and Extreme II forking the extreme base I directly, rather than having the food by Extreme II, then Extreme I Express. The network showed that the desired branched network yesterday, but today went back into the linear trajectory. I tried a simple drag and drop graphic to move the Express, thinking that surely the Apple would implement such a simple, logical and direct way to manage the network, but no. Have not seen another way to configure the network manually, so any suggestions would be appreciated.

  It is very important to understand that Apple "extend a wireless network" works on signal strength.

  In order to have the AirPort Express and AirPort Extreme to extend the network of the 'main' extreme wireless, two conditions must be fulfilled:

  (1) the AirPort Express and AirPort Extreme extension should both be on the same relative distance of the extreme 'main '.

  (2) AirPort Express and AirPort Extreme extension must both be closer to the extreme 'main' they are to each other.

  In other words, a well put together would have your "main" AirPort Extreme in the middle of the House, with a Terminal AirPort Express on one end of the House and the AirPort Extreme to the other end of the House.  In this configuration, the two airports are about the same distance from the extreme 'main'... and... "" oth extending airports are located more close to the "main" airport that they are with each other.

• How can ensure me that I am connected to the Wan, not the Base Station?

  I have one extreme as a base station, with an express the upstairs of the extension of the network. There are green lights on both, the utility displays the Express connected to the extreme and it is not a big house, so it seems that the network is configured correctly.

  However, when I'm near the Express, my MacBook Pro connection speed is significantly slower: 9Mbps, vs 30Mbps when close to the extreme. As far as I know, I am always connected the low extreme, rather as the Express I sit beside.

  Is there a way to say that I am connected to? Or y at - it a way to choose who to connect to?

  Thank you-

  In AirPort Utility, click images extreme and Express. A list of connected devices appears in the windows that appear.