BD drive doesn't work

Similar Questions

• EA4500, network drive doesn't work without access to the secure folder

  The map I try the USB hard drive connected to my EA4500 router as a network drive in Windows 7 and it works perfectly until I have enable access to files on the router.

  After enabling file access secure and do not change other settings of the router I first disassemble the drive because it has been implemented without credentials and does that any more.  When I try to remap the drive I use the same address, but select 'Connect using different credentials' when he invites me to the log in info I try to use the router administrator account, but it fails to connect.   Diagnostics Windows network tells me that the device has refused the connection.  I have to create an account on the router in the settings of folder with the same username and password that I use on my computer and tried to connect it without checking 'Connect using different credentials' (and them by manually typing if it matters) with the same results.

  Even with secure file access enabled, I can still reach the reader very well by typing 'ftp://192.168.1.1/' in the file Explorer.  It prompts me for a username and password, I put in the administrator credentials, and I'm in.  The account, I created with the same name of user and password that my computer works this way.

  After you turn off access to the secure folder as everything is working perfectly again...  I'd rather do it with him, however.

  Follow these instructions: http://homekb.cisco.com/Cisco2/ukp.aspx?pid=80&vw=1&articleid=25813

  When you click the Browse button, that the router shows up when access to secure files is disabled, but not after it is activated.  I've looked through my sharing settings windows and haven't noticed something that should cause problems, about that everything is allowed.  I also tried disabling my firewall without success.

  Well, that was weird...

  I have reset the router, was able to operate with secure file sharing is enabled, but only, I could get a device connected to the player.  I went in the USB storage on the router settings and started to get a bunch of error 2123 and 2118 s to the point that I was not yet able to change the settings.  On the USB, I noticed a file named "." ftp_share.nfo"what is strange because it seemed sure whether a file instead of a folder in previous tests.  I deleted the folder and all the errors disappeared, had haunted all my settings for the drive into the router, and now it works perfectly...

• USB 3.0 flash drives doesn't work is not on the USB 2.0 in windows 7

  My kingston USB 3.0 does not no flash drives or supported on USB 2.0 in windows 7 and 'The window error' occurred: Windows found driver software for your device, but has encountered an error trying to install.

  Hi Faisal,.

  What is the brand and model of the computer?

  You will need installed USB 3.0 drivers on the manufacturer's Web site work with the USB 3.0 flash drives.

  Try the methods provided below and see if they help to resolve the issue.

  Method 1:

  This problem occurs because the USB 3.0 device is not completely inserted in the port.

  The USB 3.0 supports the devices USB 1.0, 2.0 and 3.0. The first layer of pins inside the USB connector are for USB 1.0 and 2.0 ports. The second layer of pins inside the USB connector is USB 3.0 ports. Therefore, to resolve this problem, make sure that the USB 3.0 device is inserted in the port.

  Method 2:

  Uninstall and reinstall the USB drivers and check if it helps.

  To remove and reinstall all USB controllers, follow these steps:

  (a) click Start, run, type sysdm.cpl in the Open box and then click OK.

  (b) click on the Hardware tab.

  (c) click on the button Device Manager.

  (d) expand Bus USB controllers.

  (e) each device under the node Bus USB controllersright click and then click Uninstall to remove them one at a time.

  (f) restart the computer and reinstall the USB controllers.

  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.

  We know the results.

• Mapping to a network in Windows 7 drive doesn't work at home location but works at the location of the Office

  Hi all

  I think that the title also my problem that I'm having now. I don't know if I have to install or remove additional security stuff in order to have the mapping network drive work in my home region. No matter how many times I tried to map a network drive that is host to somewhere in the United States as a dedicated server running Windows Server 2008, home to my laptop it keeps popping "Path not found" error message, but when I'm at the Office I am able to map the network drive with the same computer laptop and office network is not the area with dedicated server they are different network.
  Y at - it an idea why and how to solve this problem?
  Thanks in advance
  Sam.

  Hello

   

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

   

  http://social.technet.Microsoft.com/forums/en-us/winserverfiles/threads

  I hope this helps.

• New hard drive doesn't work is not for me

  I have to delete and automatically add the existing disks to virtual machines. The removal works, but for some reason, I can't New-hard drive to work. Here is how I call it and the result:

  > $drVm

  Name PowerState Num CPU memory (MB)
  ----                 ---------- -------- -----------
  Test-VM 1 2048 PoweredOff

  
  

  > $drPath

  [ds_name]  VM-name/VM - Name.vmdk

  
  

  > New-disk-hard - VM $drVM - DiskPath $drPath

  New-HDD: 15/05/2012 11:10:33 New-disk hard no. datastore corresponding found.
  On line: 1 char: 13
  + New hard drive < < < < - VM $drVm - DiskPath $drPath
  + CategoryInfo: ObjectNotFound: (:)) [new-harddisk], VimException)
  + FullyQualifiedErrorId: Client20_VirtualDeviceServiceImpl_NewVirtualHardDisk_DatastoreNotFound, VMware.VimAutomation.ViCore.Cmdlets.Commands.VirtualDev
  ice. NewHardDisk

  
  

  > Get-Datastore-name "ds_name.

  Name FreeSpaceMB CapacityMB
  ----                               -----------      ----------
  16335 16384 ds_name

  Values and types appear to be correct, but it does not work. At one point, I had this working but then stopped. I had recently upgraded to v5 PowerCLI so I supported that, but it still does not work.

  I am passing the VM as a virtual machine type and the path of the disk as a string by the docs.

  Any help would be appreciated. Especially if I'm doing something stupid. It is such a simple function.

  I thought as well

  The virtual machine can be a VM object or even a string with the name of the virtual machine. The functionality of the object by name (NVOS) will ensure that the hard drive New cmdlet retrieves the virtual computer object. And Yes, the path is a string.

  If you assign the hard drive manually, then do a Get-hard drive, you see the same way that you use in your script?

• my network drive doesn't work what can I do to fix

  He said the network drive is not available how can I fix this setting

  Hello

  1. have you made changes on the computer recently?

  Follow the steps listed in the article below and check.
  New drive or mapped network not available in Windows Explorer drive
  http://support.Microsoft.com/kb/297694

  I hope this helps.

• E1505 cd/dvd drive has stopped working

  suddenly, my cd/dvd drive doesn't work! It will not read any dvd or cd.  It is a TSSTcorp DVD +-RW TS - L532B.

  
  

• WIFI doesn't work does not correctly after driver update

  I have a DESIRE 4 laptop 1023tu with operating system Windows 8 PRO. My WIFI works does not properly after the update drievr.

  Problems...

  1. When you try to connect to a wifi hotspot the quick adapter turns off and allows the card instantly

  2. after connected, sometimes no internet access and the problem turns off only after reconnecting to the netwrok after setting off.

  If the update doesn't work not for you then do as I explained in my previous post and roll back to the previous driver. This philosophy can be applied to all updates.

  If there is no pressure or emerging reason to update to your PC or laptop works just great... do not update. (this is especially true when it comes to an update of the BIOS)

  For your question #2, the problem could be your wireless (modem, router or access point) which causes the connection dropped.

  Best regards
  ERICO

• used ACER Aspire 5100 which has windows vista Home premium with service pack 2. It has technology MOBILE AMD Turion 64 x 2 usb ports doesn't work don't, webcam and CD/DVD drive now does not.

  I bought the laptop to a pawn shop and waiting for a few minor problems, but not this one.

  It began with the webcam doesn't work does not correctly, but works. After Device Manager running that it has detected a Xerox Pro scanner, not built in webcam which i see in front of me. I tried everything with no success, but this isn't the only problem there is... more

  After I realized that the cam is not working, all 3 USB ports leaving recognize anything and all the devices connected by a mouse flexible wireless microphone on a memory stick 4 GB, could not be recognized. All were then tested in two other PC with these things being recognized and installed on the PC.

  I have updated after him saying driver not installed, only to be told driver is already up-to-date, but will still not be recognized.

  Now the CD/DVD does not work and is not even detected in scan. says the drivers are not present or that is disconnected. I did nothing else than to go in circles are doing the same thing over and over again.

  Is there a worm or bug or something wrong freeking I know and how do I solve this problem?

  I like most of the features of vista, but if it's the doo doo a bit I have to put up with... I want XP less back pain...

  Once again can not locate or install programs or drivers to operate the integrated webcam

  All USB ports defective 3 and CD/DVD is no longer functional or even detected in laptop... HELP ME PLEASE

  Hi Laurent,.

  1. did uninstall you the USB ports on the Device Manager and reinstalled as mentioned in the previous post?

  Please see the following thread link:

  my USB say this device not yet recognized the worsks device in the other laptop why?

  Uninstall all USB device manager entries and check.

  a. Click Start and typedevmgmt.msc and then click OK. Device Manager opens.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  f. check the USB device to see if it works

  2. have you tried to uninstall the webcam?

  If this is not the case, try to uninstall the webcam in Device Manager and install the latest version of the drivers from the following Acer site.

  Acer Driver Downloads

  On the problem of DVD player, you can try the steps in the following article and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Hope this information is useful.

• Driver Intel WiUSB doesn't work does not correctly?

  USB - IFxHCI Intel WiUSB USB host controller driver does not work properly because it has random (or whatever) yellow sign in management devices..., how can I get this driver? my laptop is a T430.

  Hey there guoyaorun,

  I found some information on thisthreadcan be beneficial to your situation. This charge USB controller via wireless as part of the display (WiDi) Intel wireless function. To get a fix, you will have to go on the Site of Inteland run the Intel driver update utility. This should identify the Intel drivers that you have that are more up-to-date, including the WiDi driver. Hope this helps!

• Satellite U400-112 CD/DVD optical drive doesn't read CD disks

  Same problem, my CD/DVD drive doesn't read any cd, but it works with the DVD. Same problem if I try to burn CDs (it does not work, clear yellow on the drive and the drive gets hard blue light on the laptop (U305) permanently on) but it's ok to burn DVDs, even if it takes long to start reading a new dvd. How to solve it? I tried to find a new firmware for the drive, but apparently does not exist (my drive is HL-DT-ST DVDRAM GSA-U10N ATA device). Can anyone help? .

  HI Arkadiusz Kulesza,

  You should try to clean the lens using a microfibre cloth. Maybe dust is on the lens it takes long to start to read the disc.

  I had a similar issue that he wasn t possible to burn a DVD and the reason was the CD/DVD drive itself. I replaced it with a new one and everything worked then! :)

• Qosmio F20: Featured work Touchpad scroll doesn't work anymore

  Hello

  I have a Qosmio F20 and only had it for less than a year, I've always used the touchpad and the quick launch feature, never changed anything in the settings of the touchpad, or major changes in the operating system, I have a problem now!

  the scroll function working keys doesn't work anymore, you know how the right side is scrolling up and down and low to the left/right scrolling, now it doesn't work... my brother was using my computer and he has installed a bluetooth, infrared driver program, he used a mouse USB and install Nokia PC suite.
  NOW what should I do? HEEELP!

  Thank you.

  Hello

  Brother have installed you a large number of applications and also a USB mouse.
  Who knows what it changed on your laptop.

  If the pad touch scroll function does not work so I guess that the settings have been changed.
  In your case, I recommend to check the touchpad settings.
  You should find your mouse over settings in the control panel.

  As far as I know, you can find these settings in the Toshiba touch and launch.

• Qosmio modem: after update the modem driver does not work

  Qosmio F10-145 with WSP2 MCE.
  Yesterday, I installed Phone Dialer Pro. Then, I realized that the microphone did not work with this program.
  The help file suggested upgrade modem driver that I then downloaded from the Toshiba site.
  It was the last time that my modem was working.
  I tried everything: from the update to restart in SafeMode as administrator, remove the driver and reinstall it from the Tools CD, use SFC and all I get is an 'access denied' message at the end of the installation process.
  System Restore doesn't work anymore as the last point of available restoration after the "Reinstall".
  I called help line of Toshiba which suggested resettlement of the entire system using the recovery CD... That would take days (programs, updates, mail files + digital certificates...).
  The last option that is somewhat like a spare wheel, as it has to install an external modem PCMCIA. This worked well but is frustrating because there is a modem already installed.
  Also, why don't I have any problem installing external modem, but cannot install one that is already there?
  Any suggestion?

  [Edited by: admin on 24 June 05 19:18]

  Hello

  As far as I know Toshiba Software modem is connected to COM 3.

• HP 14-r206nv: light wireless led doesn't work do not

  I have a very minor issue that don't mind operating of the laptop, but I'm curious to know why it does not work, because I know that before reinstalling windows it worked normally.

  Well well, to the point now. After a hard drive failure and replacement, Windows 8.1 are installed again and each driver has been installed and works well. The only thing that doesn't work is the led light button wireless (F12). The button is working correctly, activation and deactivation of the Wi - fi, but not the led. It lights, neither white nor red, it is always disabled.

  The model of the wireless card is Realtek RTL8723BE.

  I installed the drivers from the HP site.

  Version of the driver for the wireless card is 2013.8.915.2014

  The version of the wireless button driver is 1.1.7.1

  I tried the latest drivers for the card (an optional windows updates finds) implemented to date for this and the wireless button (if I try update driver in Device Manager, it installs a new) but nothing has changed for good so I decided to go back to what the official site suggests and post here.

  Hi @v1184,

  Thank you for your inquiry.

  I understand that you had a hard drive failure and he had to be replaced, you did. You reinstalled Windows 8.1 and all drivers are up to date.  The only problem you are having is that the wireless button light does not illuminate, but it does not work.

  You tried to update the wireless driver button, but has not changed, so you returned back to the recommended HP driver.  As the wireless button does not work it is not the driver, however, it could be that the light burned. The other possibility would be that when you replaced the hard drive, the connection has been dislodged or disconnected and must be reconnected.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on ' Thumbs Up ' below is a great way to say thank you!

• Sat 1900 - CD/DVD drive does not work properly. How to solve this?

  Hello :-)

  I have a Toshiba Satellite 1900, bought in 2003. It has a cd/dvd drive called MAST * UJDA720.

  For the last 3-4 months he was not working properly with movie DVDs. whenever a movie starts, it does not work smoothly, but in stop-and-go. First of all, I had everything again and it works fine, but lately, he never runs well and some DVD doesn't work well at all. Excuse me it I do not explain, I don't have the words in English.

  But maybe someone understands me and can help. My DVD player is dirty? Is there something like a standard CD? Or do I have to give the laptop to a repair shop?

  Thank you in advance, I would like to have my DVD player, back to normal - especially as I don't have a TV.

  concerning
  Kimbazulu

  Hello, Kerstin

  If you can watch the DVD on the unit I don't think the drive is defective. I have the same unit and still work well. Stop and go while playing DVDs can be caused due to the high utilization of the processor.

  Please try to start the Task Manager and check all running processes. All unnecessary processes can be stopped and on this way, the CPU will go to a lower level. If the antivir software is installed on your unit checking if this software analyzes the HARD disk and stop it.

  These things together can be responsible for stop and go while playing DVD movies.

  Good bye