Belvedere on the installer of Windows 7 virtual machine on the server

Similar Questions

• How to reset the administrator password in my Windows XP Virtual Machine

  I just created a Windows XP virtual machine and have been using it without any problem.  Today, I started the machine and he asked an administrator password.  I believe that I have not set up one that I've never been asked before.

  How can I reset my password or I have to rebuild a new machine?

  Can I use a password reset utility?

  Thanks in advance for any help.

  Kind regards

  Doug U - M

  If an empty password does not work then you probably have to rebuild the virtual machine. This time, I recommend adopt you the practice of setting up a second admin account immediately and make a note of the password. It's the same when you buy a new car: you get at least two sets of keys.

• Help please... Replaced the hard drive of MBP, restored from TM, but the Windows XP virtual machine does not start

  I replaced the 250 GB hard drive in my MacBook Pro early 2009 with a 500 GB drive, it the Mac OS extended (journaled) format and restored from my Time Machine backup.

  Now when I try to start my Windows XP virtual machine (using Fusion 2.0.6... planning upgrade to 3.1.2 but wanted to validate all was well first), I get BSOD, even in safe mode.

  I have my vm separately saved on a network drive data files based on things that I had read before, I do not think that TM backup of virtual machines. However, a friend with a similar setup with more knowledge I think because I could see my Windows XP vm VMWare listed under 'Documents' in Time Machine showing its full size, it has actually saved and there restore it. Apparently he has done this successfully before.

  Should I have partitioned the hard drive? I don't think that my previous drive has been partitioned. Don't know what to do now.

  TIA!

  Katie

  To be clear: you have restored VMs from the disk or network time Machine?  And if the network drive, what backup method you use?  (i.e.: have you just copied engine off the computer virtual package or not?)  Can you copy/restore the virtual machine to the network again drive?  What is a virtual machine that has the error, or other virtual machines have problems?

  Time Machine backup correctly a virtual power off machine. But since Time Machine works automatically, you often will get not a consistent backup unless you do some tricks to make sure Time Machine backup only when you use a virtual machine.  (i.e.: turn on Time Machine only when you're done with the virtual machine.)  Thus, it is normally recommended to exclude the virtual machines from Time Machine and use another method to back up virtual machines.  Your friend is lucky or is only backup virtual machines powered off.

  Should I have partitioned the hard drive? I don't think that my previous drive has been partitioned. Don't know what to do now.

  The Mac player Paritioning is unnecessary unless you use Boot Camp or have required another for the partition.

• Backup my Windows XP virtual machine.

  I need to know what files I need to copy so that I have a backup of my Windows XP virtual machine. I use Time Machine to back up my Mac, but I've read the discussion properly if not the right way to go. If anyone can please tell me what to do in case I have a hard disk crash.

  Fusion obscures the VMs - files in a package.
  If you open you a list of files.

  More important are all VMDK + vmx file.

  But to simplify it - simply copy all files while the virtual machine is turned off

• Conversion of the virtual machines in VMWare Server 1.0.5 to vSphere Enterprise

  I have a couple of windows XP virtual machines running on VMWare Server 1.0.5.  Can someone point me to instructions for turning them into vSphere (ESXi 4)? The conversion occurs in the vCenter Server or with a separate program?  Thank you!

  VMware Converter, which is integrated with vCenter Server and the Client must be able to do this by directing it to the virtual VMware Server 1.0.5 computer files.  You just need to save the pluggin converter in the Client to use vCenter converter function.

• Cannot save the virtual machine in VMWare Server 2

  Hi all:

  I created a VM (12.1 OpenSuSE 32bits) in VMWare Workstation 7; then I copied it to a host VMWare Server 2.

  When I try to save the virtual machine via the web, the server fails (or at least interrupts the response from Web page), so I tried to save it via command line.

  After searching a bit I found this:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1006160

  The question is now that I can't find any vmware-cmd anywhere, and when I run vmware-vim-cmd I get the following error:

  vmh2: / data/vmachines/postgresql-box # vim - vmware - cmd solo/registervm /data/vmines/postgresql-box/postgresql-box.vmx
  Connection failed: vim.fault.NoPermission

  So I'm stuck... someone can help me?

  BTW: what is ESX, ESXi and what version of ESXi is included in VMWare Server 2?

  Thank you very much

  Luis

  I can't tell you exactly what are the causes of the problem. What I would try (a solution) is to create a new virtual machine in VMware Server with the same specifications as the original one, then copy the two files hard in the new virtual machine folder and edit the .vmx file for the new VM 'OpenSuSE - 12.1 - cl1 - 000001.vmdk' use as its virtual drive.

  André

• Transfer of virtual machines from a server ESXi 3.5 to new ESXi 4.1 server. What is the procedure.

  I read on how to transfer a virtual machine from one server to another using VMotion. Not 100% clear on the process again. What I see or read is when you do this since an ESXi 3.5 Server ESXi 4.1 server, I do not see any information on, if possible. In addition, I have not read if I need to convert or upgrade the virtual machine until I use it on the new server. So, my question is, are there any special instructions, conversion tools to convert a VM created 3.5 to use on the new Server 4.1? Is there a detailed procedure that I have not yet found or read best describes this process. Like I said up to now I'm not 100% clear on the procedure. Thank you.

  ESX 3.5 VMs can run without modification on a host ESXi 4.1 - VMotion between the two hosts, you will stiil need to ensure CPU compatibility between the hosts.

  Maybe it's the best guid for upfrading to vSphere - http://www.vmware.com/pdf/vsphere4/r41/vsp_41_upgrade_guide.pdf

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Can't get OS USB host for the installation of a new virtual machine

  I am trying to create my first VM in VSphere client. All my other machines have been migrated to Hyper-V machine. I created the machine but can't load of windows server 2003 r2 32 bit OS ISO. I tried several ways to no success.

  The virtual machine just says: operating system not found. The first way I tried was put the installation disc in the VSphere host and modify the virtual machine settings to point to the CD-ROM. It did not work.

  The second way, I tried was by clicking on the icon of the disk to the VM Console and choosing iso on the local disk. I then navigate to the iso file. When I did this it remains stuck in the connection. Even after I change this setting if I try to go back to the icon of the drive console he says always login no matter what I do on the parameters of the virtual machine. Can I stop it trying to connect?

  The third way, that I tried was to stick to a USB to the VSphere host. However, I can't understand how to assign the virtual machine to USB. I noticed that when I plug my USB key, it says USB configuration has changed in the events, but I do not see the USB drive as an option under storage.

  The fourth way that I tried was to use WINSCP for SFTP the ISO for the data store. When I do this need me in the root directory that has only about 100 MB of space on it. So it allows me to start the transfer of the iso and the error. How can I change this?

  I'm really frustrated about something which I think should be really easy. Any help is appreciated.

  You have access to vCenter?

  If so, this video shows how to download an ISO: http://www.youtube.com/watch?v=c6v8GsWJ9dc

  If you get your ISO on the data store that you can navigate to it through the client vSphere (console) to the virtual machine, do not forget to set the "connect on startup' or 'Connected' when you configure the virtual machine's CD drive.

  [Edit] Boot from USB can sometimes be a problem, if you need to boot from USB you can use a like Plop Boot Manager, it is an ISO standard, you can load into the virtual machine CD player. More info here: http://www.vladan.fr/great-tip-how-to-boot-from-usb-image-in-vmware-workstation/ ... It's for workstation, but it works for ESXi 5.0 as well.

  Post edited by: spravtek

• SCSCI driver probem in the Windows XP virtual machine

  I searched but couldn't find details on installing the SCSI driver told me that I need when I start my VM with Windows XP home. I downloaded the file the indicated such driver disk, and I tried to add a floppy drive for my virtual machine, while the guest is turned off, but then when I start upward once again I get a black screen and a message 'missing netldr '. There is nothing I can do at this time. Is there another way to get the driver, as well as a diskette file?  This seems like a ridiculous way to deliver pilots.

  Carl the key here to what the OP said is "told me that I need when I start my VM with Windows XP home" and this message that becomes the OP has nothing to do with it is not able to boot and there is actually a checkbox on the message to not show it again because the SCSI driver may not even be necessary , and in general with this particular message that they are not necessary.

  If it was a case of need of start due to a virtual hard disk SCSI SCSI for Windows driver then the message would come from the installation of Windows that has a hard drive was not found.

• Runtime error example NOR-DAQmx ANSI C in the Windows 7 virtual machine

  I am under a guest Windows 7 system with a host of Ubuntu 14, using VirtualBox and have encountered a problem running even the simplest examples provided by National Instruments, using the ANSI C API for NOR-DAQmx.

  The first time that the DAQ hardware is turned on, I can run a single measure, and after that, any other indicator displays the following error message:

  Attempted to read samples that are no longer available.
  
  The requested sample was previously available, but has since been overwritten.
  
  Increasing the buffer size, reading the data more frequently, or specifying
  
  a fixed number of samples to read instead of reading all available samples
  
  might correct the problem.
  
  Property: DAQmx_Read_RelativeTo
  
  Corresponding Value: DAQmx_Val_CurrReadPos
  
  Property: DAQmx_Read_Offset
  
  Corresponding Value: 0
  Task Name: _unamedTask(0)
  
  Status Code: -200279

  In order to start a new measurement, I have to restart the DAQ hardware, probably in order to clear the internal buffers that are in the process of substitution.

  I am interested in a measure of continuous tension in basic by using a callback function. (The example of ContAcq_IntClk provided by OR)

  The exactly the same setup, same version of NOR-DAQmx (9.7.5) and running on Visual Studio 2012 smoothly on a computer that is running Windows 7 directly.

  I suspect that the problem is with the internal buffer being somehow messed up because of the connection with the Virtual Machine, but do not find an elegant solution to fix it.

  The camera I use is NI USB-6289.

  Hello fromm8

  Thank you very much for your help, I managed to locate the problem.

  He was not the actual code, or something like that, it was a problem of communication between the VirtualBox machine and the physical device.

  Kept launches MAX test panels a comparable as error the program C.

  I fixed the problem by opting for VMWare, which seems to have the best compatibility with USB devices.

  See you soon!

• See the Windows 10 virtual machines as "Available" in the administration Console, even while users are connected

  Hello

  I have the situation where a bunch of persistent Windows 10 VM VDI (several pools, all VM 1 by manual pool) are ALWAYS shown as 'Available' in Admin mode, even when a user is connected. Using PCoIP or RDP has no importance.

  Description:

  -All the time, desktop never appears as 'connected' in the Admin view when users log on. It's always 'available', which is dead wrong in the first place.

  -L' use of PCoIP disconnects-> reconnects with PCoIP or RDP.

  -Using RDP at a certain point however, triggers the message of "sources of funds available for this desktop computer are currently busy" clients of the view. Re-login impossible at all from that moment, regardless of the protocol used.

  -Once again, yet these VM Win10 see as "available" regardless of the actual status.

  -There is no firewall between windows 10 VM and connection brokers (who have no problem replication).

  -Restarting the agent from the view and related services does not 'release' of the virtual machine. It will still say 'sources of funds available for this desktop computer are currently busy.

  -Only a restart of the operating system can erase it and make the available virtual machine to connect again.

  -While the virtual machine is amplified shutdown or restart, desktop shows as "inaccessible Agent" so there is communication between Agents and brokers.

  Windows 7 persistent VM works 100% normal in all respects. It's only 10 VM Windows and... Since a round patch in a few weeks (I was this problem since then). Before some patch does this (but have no evidence) these VM Windows 10 has worked well with view 6.2.0

  These virtual machines are highly customized with special software and can not be simply rebuild. I re-install VMtools, view Agent etc etc several times. No dice. Even tried a fresh install of Windows (connected to the same level), still shows this behavior.

  All this started a few weeks back after a round Patch from Microsoft. Then maybe a M$ Patch assigned Agent of the view. So I uninstalled/re-installed the Agent of 62 reviews. Improved 6.2 to 6.2.2 etc. all to nothing does not. New, old, VMtools Agents re-installed. I've tried everything now.

  Has anyone seen this or someone can point me in the right direction for troubleshooting? I haven't noticed any funky stuff in the papers, but I'm probably tunnel vision/search the bad things after all this time.

  I do view since the early days, but I'm really stumped this time. I am all of these ideas.

  I reworded my question in another post and found the answer here:

  Win10 Desktop shows never "connected" while the user is logged

• Browse the option not available when I go to the window Edit virtual machine settings, why is it?

  Hi all

  Happy to be part of the VMware community , announcing my first question to you all. After creation of the Virtual Machine in an Esxi host, when I try to picture mount the ISO for the guest operating system, option browse is not highlighted, why is this so, and is not for the administrator or root user, this problem happens for the normal user, happens because of all the rules of host-level? If its happening because of the rule in ESXi settings, please guide me how to change it?

  The role will thus the privilege of 'connection to the device:

  

• Newbie installation window vs virtual machine virtual Boot Camp

  HI: is there a document/link that describes the difference, and what benefits the Boot Camp virtual machine has?

  Thank you

  Ravi

  Take a look on: choose the right virtual computer settings

• New Windows 7 virtual machines always Home Basic?

  Hello

  I just installed the most recent (7.1.2) VMware Workstation on my Windows7 Ultimate x 64 host, but whenever I try to create a new virtual machine, be it an operating system Windows 7 x 64 guest professional or Ultimate to Windows 7 x 64 N, the virtual machine always starts as Home Basic.

  Why?

  Thank you.

  Looks like you use the function 'easy install '.

  next time, when you try to install windows 7 click on "I will install later...". ' - which disables detection automatic bone and if all goes well then allows a very easy installation ;-)

  _________________________

  VMX-settings- WS FAQ -[MOAcd | http://sanbarrow.com/moa241.html]- VMDK-manual

• Windows 7 virtual machine - stop even if someone is connected via RemoteDesktop

  Hello

  I have a machine virtual windows 7. It runs on a host SLES 11 SP3 with KVM. When the host wants to stop the virtual machine, it signals the vm via ACPI. But if someone is connected via RemoteDesktop, virtual machine refuses to stop. KVM waits a while, then turns off the virtual machine. Is it possible to stop a windows 7 even if someone is connected via RemoteDesktop?

  Something like for example a registry key?

  Thank you.

  Bernd

  Hello

  Thanks for posting your query on the Microsoft Community.

  According to the description, I understand that you are facing problems with Windows.

  I suggest you post your query on The TechNet Forums , because we have experts working on this type of questions and for you help the better.

  Check out the link:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.