Bios HP Compaq nx6310 problem

Similar Questions

• HP Compaq nx6310 - Windows 7 32 bit - power-processor-core of event ID 37

  Hello everyone,
  
  I just installed Windows 7 Ultimate 32 bit on my HP Compaq nx6310 computer and whenever the system starts up, I get 2 warnings in Event Viewer

  • The speed of the CPU 0 in group 0 is restricted by the system firmware. The processor is in this state of reduced performance for 71 seconds since the last report.
  • The speed of the processor 1 group 0 is restricted by the system firmware. The processor is in this state of reduced performance for 71 seconds since the last report.

  That also seems to happen on Windows Vista Ultimate 32-bit Edition SP1, but it is not on my Windows XP system. The problem will not occur if the system (Windows Vista or Windows 7) has been started in safe mode. Is there something I can do to fix this?

  Here are the specifications of my computer:

  • Processor: Intel Centrino Duo: Genuine Intel(r) CPU T2300 at 1.66 GHz (Dual Core)
  • Motherboard: Hewlett-Packard 30AA (KBC Version 58,13)
  • BIOS: Hewlett-Packard 68YDU worm F.0E (2008-02-21)
  • Memory: 1024 (2 x 512) MB DDR2
  • Graphics card: 256 MB Mobile Intel(r) 945 Express Chipset Family (Microsoft Corporation - WDDM 1.0) [400 Mhz]
  • HARD drive: 150 GB TOSHIBA MK1652GSX ATA Device
  • Model: HP Compaq nx6310

  Thank you
  Any help will be greatly appreciated.

  Thank you very much for your reply and I apologise for the delay. I tried to understand the problem, then I discovered that the maximum frequency of the processor is stuck at 59% via the resource monitor, I guess that's why I got a warning in the event log. I tried switching without result power plans. I think it's something to do with saving technology (even though I'm on AC) of energy, but I can't control how my processor or how power is saved via the BIOS (I don't have the options for this)

  However, Safe Mode, I get 100% maximum frequency.

  EDIT: I managed to understand it with the help of CPUID! My CPU clock is automatically reduced when I walked into Windows 7 in Normal Mode (I guess it's something to do with the processor), so I downloaded ThrottleStop and restored the multiplier to 10, where now is 99% maximum frequency and the computer is super fast! Thank you very much for your kind and helpful suggestions, I hope this helps anyone having the same trouble.

  EDIT: The problem was EIST (Enhanced Intel Speedstep Technology), who strangled the CPU while it was hot. I disabled it remove its driver from the OS and then I was able to get 100% maximum frequency.

• Password bios clear (Compaq CQ-42)

  I have a compaq cq 42 laptop has a bios password I do not know.  My deactivation code is 66736106.  Can someone help me to access the bios and solve my problem?

  Thank you

  Jody

  I would add that I run a computer repair shop and this notebook belongs to a customer whose children set a bios password and of course can't remember what they were doing.  So, it has not been stolen or something like that.

  Hello

  Enter: 79694128

  Kind regards

  DP - K

• HP Compaq 610 ((Intel PVU): how to downgrade bios on Compaq 610?)

  How downgrade the bios on Compaq 610? I got bios ver. F.20

  I want BIOS version f.08!

  

• BIOS has detected a problem with cooling on hp Mini 210-1004sa fan

  I tried to boot my system and received a message that the BIOS has detected a problem with cooling fan and if the system wouldn't start. Please, what is the best way to solve this problem.

  http://support.HP.com/us-en/document/c02066988

• Compaq CQ58: I forgot the password admin or bios for compaq CQ58

  I forgot the password admin or bios for compaq CQ58

  my code is 94289323 please help

  @leonaedo

  Enter 21181905

• Password BIOS on Compaq CQ61 said administrator or power on password.

  Password BIOS on Compaq CQ61 said administrator or power on password. The code after several test is 68879364. Can someone give me a new password code

  Hello

  Pleae try:

  77751960

  Kind regards.

• HP Mini 110: Reset password BIOS HP Compaq Mini 110

  Hello:

  Help, please

  My password bios HP Compaq Mini 110.

  After 3 try a me check failed and display code below

  CNU0073YDD

  Help, please

  Thank you

  Alex

  @awong2608

  Enter: e9l11xfitt (3rd character is a lowercase L)

  Kind regards

  DP - K

• stop and restart the BIOS G470 2.19 problem 40cn33ww_64

  Hi there, please kindly help me.

  I have laptop of G470, Lenovo. Core I3, 8 GB RAM, 500 GB HDD, Bios Version 2.19 (updated)

  in fact, after I have updated to version 2.19 bios I got these problem.

  When I click on stop. the disc but stops the power still running.

  When I click on restart (on battery) my laptop goes off completely

  When I click on stop (on the adapter) my laptop will reboot.

  first of all, I think that it is BONE, I have try all the BONES, but it is still the same problem.

  Please give me a solution. Thank you.

  
  

• COMPAQ PRESARIO CQ61: Recovery of Bios Password COMPAQ PRESARIO CQ61

  Recovery Bios Password COMPAQ PRESARIO CQ61 operating system: Microsoft Windows 7 (32 bit) Hello, I have a COMPAQ PRESARIO CQ61 and suddenly asks me the password of the bios. The message that appears is "ENTER password or POWER ON PASSWORD". What can I do? After failing 3 times I get the message "System disabled" and the code 50949691

  Hello

  Please read the first post on the link below...

  http://h30434.www3.HP.com/T5/notebook-operating-Sy...

• BIOS HP Compaq Elite (i5-2400 CPU) 8280 cannot set the VT option

  BIOS HP Compaq Elite (i5-2400 CPU) 8280 cannot set the VT option

  found in the security system] [, thanks]

• Updated BIOS for Compaq F700 computer laptop Windows 7 OS

  I am trying to upgrade the BIOS for Compaq F700 computer laptop F.04 to F.08 worm!

  I can do it under Windows 7 OS (the sp39468 WinFlash file is recommended under Vista environment)?

  Thank you

  Make sure that your antivirus program is disabled. It should be in safe mode, but check to be sure.

  If the antivirus program is active for a windows-based BIOS flash, the antivirus program may try to interrupt the flash 'think' a virus attacks the BIOS. A BIOS flash interrupted computer = death.

• BIOS HP pavilion m7463 problem

  Hello

  I was given a hp pavilion m7463, who had died, so I gave him a new hard drive which works very well.  I even just got a new monitor as well.  Now this computer came originally with XP... but it wouldn't work on the disk hard that I added, but I got a copy of Vista to run.  Thanks to all that the computer worked well.

  Earlier today, I tried to update the BIOS because installed was a bit outdated and does not support boot from USB drives.  The old BIOS version was 3.15, and I downloaded the new version (3.19) directly at HP.  After the installation of the new BIOS, the computer continues trying to start, but he can not find windows or a handle than some delivers so it restarts, then tries again and the process keeps going.  You try to run repair from cd vista did not help.

  It seems that if I restore the BIOS to 3.15 so I should be able ti solve the problem, and I'm fairly certain that I can install the BIOS if I can get my hands on a copy.  The problem seems to be that HP has a TERRIBLE site when it comes to drivers.  I can find the drivers/BIOS current listed, but no where is I was able to find a list of Alumni BIOS/driver to download.  So 2 questions...

  1. just install the old BIOS will fix my problem more likely?  If this is not the case, what I should try?

  2 - does anyone know where I can find the BIOS HP version 3.15 for the motherboard ASUS P5LP - THE (and I need a version of vista/xp of the BIOS or is it important?

  Thanks for the help.

  It is possible, at a distance, you need to install the SATA ACHI drivers on this model.

  See if there is a setting in the BIOS under storage options to change the setting from ACHI to IDE, if such an option exists to the controller.

  If it is set to DCIS, is why you can not install XP without loading the AHCI drivers at the F6 prompt you get when you start the installer of XP.

  Vista and W7 have these drivers as part of the Setup disk, where XP does not work as it was released before such things ACHI.

  If you have such a context and can change to IDE or legacy, XP will load right up.

  Paul

• Compaq Presario 6604AU-BIOS and other startup problems

  My laptop Compaq Presario 6604 to THE beginning to give a lot of problems in recent times. Every day, I spend a lot time on their fixation; no resolution anyway.

  Problem 1: BIOS hangs at startup

  Problem 2: If the MESSAGE is finished, Windows crashes at startup (Vista blocking at the mobile bar)

  Problem 3: for the last three days, CD/DVD-ROM does not.

  System configuration: CPU AMD Athlon X 2, 2 GB DDR 2 RAM (2 x 1 GB module). nForce Chipset MoBo, GoMobile GeForce 7150 Graphics Card 160 GB HDD. Windows Vista Home Basic (32 bit)

  Problem 1:

  BIOS hangs at the initial screen for 3-5 minutes. After 3-5 minutes, it goes to the next screen. Pressing only works key "ESC". I tried the BIOS flashed with the latest firmware (PRICE Phoenix F 32). Problem persists.

  What I tried:

  1 memory module checked. Tried different RAM module.

  2 checked hard drive for errors - Self Test passed.

  3 flashed the BIOS with the latest Firmware.

  Problem 2:

  Vista hangs at the initial screen (screen bar trip)

  What I tried:

  1. Startup Repair

  2. removed PCMCIA, 1394 driver files.

  3. system restore

  4 re-installled Vista.

  It's really frustrating to see the screen hanging even after reinstalling Vista. The Startup Repair tool produces the following result:

  Signature of the problem:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6000.16386.6.0.6000.16386
  Signature problem 03:2
  Signature of the 04:65537 problem
  Signature of the problem 05: unknown
  Signature of the 06 problem: NoRootCause
  Signature of the problem 07:0
  Signature problem 08:2
  Signature of the problem 09: WrpRepair
  Issue 10:2 signature
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Problem 3:

  If CD/DVD disc problem is related to the two above, we can discuss it further. Otherwise, I'll look it up in other sections of the forum.

  Any help would be appreciated. Thanks in advance

  Solved!

  The problem was with supply management power to the motherboard. I took it to a service person and he said it's a common problem with Compaq V6000 laptop /V3000 of the series... He solved the problem in 30 mins by replacing the chips... Too bad I spent several weeks on troubleshooting the problem myself.

  I hope that this post will help someone...

  Thank you!

• Compaq nx6310: Compaq nx 6310 must use jumpers to reset the bios password

  I need a diagram that shows where the jumpers are exactly

  Hello:

  There are no jumpers on the motherboard of your laptop to clear the BIOS password.

  Please refer to page 1-4 repair for how to do to erase the BIOS P / w.

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=1839143 & docid = emr_na-c00805752 & docLocale = en_US

  Now, I would recommend some changes to the procedure, as written.

  Leave the CMOS battery for 30 minutes and not 5 to ensure that all electricity had been drained from the system board.

  Do not replace the CMOS battery before turning on the PC with the AC adapter only.

  Leave the two batteries out of the PC.

  If this procedure does not clear the BIOS P/W, then someone has put a tight security in the BIOS, and preventing the circumvention of the BIOS P / w.