Blue screen stop error message. __

Similar Questions

• Laptop keeps crashing after 3-5 minutes of availability and receive the blue screen STOP error message: 0x000000F4.

  Original title: Windows 7 Home Premium Bluescreen

  My laptop crashes after 3-5 minutes of availability and then I get a blue screen

  STOP: 0X000000F4
  I downloaded the minidump here:
  https://SkyDrive.live.com/?CID=4a15f2921dfaa4f1&ID=4A15F2921DFAA4F1%21108&AuthKey=! ALOKHvhX1bvbZEc
  as well as a log of driverview:
  https://SkyDrive.live.com/?CID=4a15f2921dfaa4f1&ID=4A15F2921DFAA4F1%21107&AuthKey=! AD1fvwA1rk6pxFg
  Tom

  Hi Vashem,

  The error STOP: 0x000000F4 can occur for several reasons. There are many reasons why your system may crash because of these screens to stop errors\Blue. The most common scenarios are: faulty drivers, hardware problem (especially RAM). In this case, the issue could be due to the motherboard is heated.

  Check firmware and system disk controller BIOS settings are correct and that the storage device has been correctly installed.

  Method 1: The problem is possibly due to material of unsupported disk controller. Check if BIOS (Basic Input\Output System) is set to IDE. Enter the BIOS and check the settings. Change the SATA to IDE option (if available). You can view the manual to do the same thing.

  Note: Be careful when you change the BIOS settings. The BIOS interface is designed for advanced users, and it is possible to change a setting that can prevent your computer from starting properly.

  Method 2: Disconnect any external devices from the computer except for the mouse and keyboard and check if that helps.

• A blue screen (Stop error) has been reported. The message contains the error details.

  Hello Hello.
  can someone help me why this error is coming.
  I use a laptop lenovo.
  Error details:
  product-windows stytem, operating
  ID-1003,
  source-system error,
  version - 5.2.
  sysmbolicname-ER_KRNLCRASH_LOG,
  error code %1, %2 parameter %3, parameter3 %4 parameter 4 %5 2 parameter1

  A blue screen (Stop error) has been reported. The message contains the error details. An event with event ID 1001 might also appear in the event log. This matching event displays information about the specific error that occurred.

  Concerning

  Chandra Murali

  .net developer,

  HYD.

  Hi Murali,

  ·         What is the random question?

  Try the following.

  Method 1: Check for memory questions

  Microsoft Online Crash Analysis - windiag

  Method 2: Updated with the latest chipset and other computer device driver updates. Log in the Web site of the manufacturer to do the same thing.

• Satellite A350 - blue screen with error message

  At the start of windows7, I get a blue screen with error message 0 x 0000116.

  Can someone help please?

  It looks like a graphics driver is a troublemaker. Try to reinstall a graphics driver in SafeMode (f8 at startup). Read this article for more information:

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/eb584685-6b8b-4ad7-B6CC-ae5ee78095fb

  It is for VISTA but should be the same for win 7 too.

• Blue screen with error message

  Product name: HP Media Center M7250n desktop PC

  Product #ED842aa-aba

  I get a blue screen with error messages asking if this is the first time I get the error and then at the end it says: it is dumping memory. I would wipe my hard drive and reinstall XP but my system is out of warranty and HP gives me a recovery CD. What are my options.

  Hello

  If you are looking to purchase a set of recovery disc for your system, you can visit the site http://www.restoredisks.com/.

  NOTE: This site is not the HP website and it's a third-party site where they provide the recovery for different computer manufacturers disk (they charge for discs).

• Help blue screen Stop error

  If it received Blue error screen and auto restart past since I did the sp1 update. I have Windows Vista-32 and the error I get is:

  Stop: 0x0000008E (0xc0000005, 0x93F042F9, 0X92CD3C50, 0x00000000)

  Win32k.sys - address 93F042F9 base at 93E00000, DateStamp 4549aea2

  I need help here. I'm going nuts trying to figure this out. I would appreciate your help. Thank you.

  Hello

  Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. Disable the installation of self as those who are older and if
  Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

  See methods of update driver generic in the next message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret
  You must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Make sure that all new equipment installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. Also, clear or
  remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use
  Safe mode to rename or to delete the faulty driver. If the driver is used as part of the system startup
  Mode process without failure, you must start the computer by using the Recovery Console to access to the
  file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the service from the system startup of
  using the recovery and then Console by removing the system service file incriminated.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x1E. You can disable the cache in memory of the BIOS to try
  to resolve the error. You must also run the diagnostics of equipment, in particular the scanner memory, which
  the manufacturer of the system provides. For more information about these procedures, see the owner
  Manual for your computer.

  The error that generates this message may occur after the first reboot during Windows installation or after
  The Setup is completed. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For problems during the installation of Windows that are associated with the lack of disk space,
  reduce the number of files on the disk drive hard target. Search for and delete temporary files that
  you do not have to have, the files hidden Internet, backup application files and .chk files that contain saved
  fragments of files on the disc scans. You can also use another drive to hard disk with more free space for the
  installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  -------------------------------------------------------------------------

  It comes to my convenience store generic bluescreen:

  Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
  This would help. Such as ITC and 4 others entered at the bottom left. And another error
  information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and
  Displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, drivers particularly video drivers but it
  are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Blue screen (STOP) errors that cause Windows Vista to shut down (blue screen of death)

  I get this on a blue screen stop code and I can't find what this code means someone can help me please v

  00000101 0 x (0 x 0000000000000061, 0 x 0000000000000000, 0xffff98000c6e180, 0 x 0000000000000001

  Best advice I've seen on this error (here: http://www.sevenforums.com/crashes-debugging/35427-win-7-clock-interrupt-bsod-101-error.html#post356791 )
  What you are looking for will be in one of the following categories:

  (a) the BIOS bug
  (b) a pilot whose activity is at the origin of the processor target lock
  (c) a defect in hardware (temperature, voltage, dust, RFI, pure and simple borkedness...)? I also wonder about default CPU)
  Therefore, check the drivers
  Then check the inside of the species (temperature, voltage, dust, etc.).
  Then run tests of stress of material

  Try this free video stress test: http://www.ozone3d.net/benchmarks/fur/
  Try this free stress test: OSS - GIMPS

  CPU Stress Tests:
  Just do 1 or 2 tests in most circumstances. I have not used one of these tests myself, so I listed everything I could find.
  - http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=19182&lang=eng
  - http://7byte.com/index.php?page=hotcpu
  - http://www.7byte.com/index.php?page=burnin64
  - http://www.overclock.net/general-processor-discussions/657486-cpu-stress-test.html
  - http://www.fossiltoys.com/cpuload.html
  - http://www.pcworld.com/downloads/file/fid, 7146-order, 1 page, 1-c, alldownloads/description.html
  - http://www.overclock.net/general-processor-discussions/657486-cpu-stress-test.html
  - http://majorgeeks.com/CPU_Stability_Test_d215.html
  - http://www.xtremesystems.org/forums/showthread.php?t=201670
  -l' or the tests suggested at this link are bootable: http://www.techsupportforum.com/forums/f15/headless-cpu-stress-testing-393435.html#post2232929

  Then try to replace parts.
  Then look for the version of your BIOS to see what changes have been made.

  Text courtesy of http://www.carrona.org/ Usasma

• Blue screen STOP error 0 x 00000124 on Toshiba Qosmio X 300 - 13w

  Hey guys and girls.

  I need urgent help with my new Toshiba Qosmio X 300 - 13W (British model) that I bought in December
  I chose to install the 64-bit Vista Home Premium on the computer and the slopes of big thing until I HAV a work of high intensity for it as a game or to have several applications running at the same time:
  The screen goes black and the sound begins to "jerk" (repeat in a very short loop for awhile) before crashing to a Windows blue screen
  The blue screen said he "detected a unsolvable material error" and the technical Ref of the error message is "STOP 0 x 00000124 (0 x 0000000000000000, 0xFFFFFA8008FE2030, 0x00000000B2000040, 0 x 00000000000800).
  Anyone else with the X 300 - 13w has this error or someone has an idea what to do.

  Some common reasons for this problem is a hardware conflict between the graphics cards NVidia and realtek audio, but this seems to be a problem with 32 bit Vista.
  The microsoft Web site claims that it is a problem of PCI-E hotswappable with Vista but with a laptop that is not possible to phyically unless the hotswap happen somehow between the GeForce 9800 M GTS and the 9400M G during the games?

  Thank you very much in advance.

  Hello

  What's with http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=144313

  How many times you want to start new thread on the same topic?

• Blue screen Stop error code 0x000000DA in XP PRO X 64. The driver's mismanagement of system PTEs.

  Seat of Windows XP PRO X 64. After you uninstall old graphics drivers, PC does not long enough to install new graphics drivers and continually, it passes loop BSoD after windows login. I disabled the effect loop so I can display the blue screen message. I read that its actually the file videoprt.sys in service pack 2. don't forget that this is the version 64-bit (located in windows/system32/drivers) who has a bug (ver 5.2.3790.3959). I did some research to get the version 5.2.3790.1830, but I can't download it to replace the current one. Does anyone have a solution for me? Currently, my PC has no graphics driver installed because of this problem.

  The minidump file showed a SYSTEM_PTE_MISUSE (da) stop error referring to the vgapnp.sys (VGA/Super VGA video driver):

  BUCKET_ID: X64_0xDA_vgapnp! VgaStartIO + 226

  The process that crashed was the SteelSeriesEngine.exe:

  Nom_processus: SteelSeriesEngi

  If the SteelSeriesEngine.exe is the process that is constantly crashing and then disable this process to start as there may be a conflict between the SteelSeriesEngine.exe and the vgapnp.sys.

  You could try renaming the SteelSeriesEngine.exe in the directory of the program SteelSeriesEngine to something like SteelSeriesEngine.old

• Blue screen Stop error dead: 0x0000008E...

  I get the blue screen of death at random, with the error: stop: 0x0000008E, followed by a group of numbers, followed by: base win32.sys - address BF9552CA base at BF800000, Datestamp 4DE797D3... How can I fix it, and what is it?

  Thank you
  Hi Kingfisher13,
   
  -Did you of recent changes made to your computer before this problem?
   
  Follow the steps listed in this article to resolve the problem:
  General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"

• Blue screen STOP error: 0x0000007B

  Last night, I shut down my computer as usual, allowing it to update itself.  This morning I turn on only to find a formidable bluescreen message:

  A problem has been detected and Windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Check for viruses on your computer. Remove the hard drives newly installed on the hard disk controllers. Check your hard drive to ensure that it is configured and completed proeprly. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:

  STOP: 0X0000007B (0X80599BB0, 0XC0000034, 0X00000000, 0X00000000)

  I tried the safe mode, safe mode with network, safe mode with command prompt (to run a chkdsk), last good known configuration and start windows normally only to be taken to the same blue screen message over and over again.

  Please help!  Thank you.

  Hello

  What were the changes made before the issue started?
  I suggest you check the section below.
  http://support.Microsoft.com/kb/922976
   
  Hope this information helps you.

• Bluetooth, causing the blue screen with error message: out of State driver

  Hello

  I am posting this in the other thread here but it was closed before I could solve the problem.
  Background:
  I left on vacation for 4 weeks and I left my computer.  When I came back, my computer was giving me the following problems:
  • Video playback of my SIN was rough and freezing - I fixed that by finding out one of the drives died on RAID-1
  • After 30 minutes, the computer would give me a Blue Screen of Death (BSOD) and reboot - I have updated every driver I could, each piece of software, update the BIOS and then finally solved the problem by updating the firmware on my boot drive: a Crucial 128 GB SSD m4

  These two problems have been resolved, but can be useful to understand the current problem

  Current problem:
  After trying to use the webcam for video chat via Gtalk or Skype, my Bluetooth Logitech MX5500 keyboard and mouse stop responding.  About 10-15 minutes after the call is completed, my computer gives a Blue Screen of Death with the message of STATE FAILURE of PILOT.
  The minidump file is available here, and I understand that the cause is due to my Bluetooth driver: http://dl.dropbox.com/u/30633232/052212-24429-01.dmp
  What I tried:
  • I've updated all the drivers available on the Asus site for my motherboard Asus P8P67 EVO, including Bluetooth and the BIOS driver
  • I've updated my HD Audio integrated system with the drivers available on the Web from Realtek site
  • I've updated all my drivers webcam and Logitech software
  • I uninstalled, restart and reinstalled my Bluetooth drivers
  • I have not matched and repaired my Logitech MX5500 keyboard and mouse
  • I uninstalled, restart and reinstalled both Skype and Gtalk for Chrome, Firefox and Internet Explorer plugin
  The ask:
  I'm out of ideas... would like to get the genius of someone on these boards help me please!

  The problem may be with the c:\windows\system32\drivers\sptd.sys:

  ******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  DRIVER_POWER_STATE_FAILURE (9f)
  A driver is causing an inconsistent power state.
  Arguments:
  Arg1: 0000000000000003, a device object has been blocking an Irp for too long
  Arg2: fffffa8009d73060, physical device from the stack object
  Arg3: fffff80004c093d8, functional device object of the stack
  Arg4: fffffa800e0c3190, blocked IRP

  Debugging information:
  ------------------

  DRVPOWERSTATE_SUBCODE: 3

  Nom_image: usbhub.sys

  DEBUG_FLR_IMAGE_TIMESTAMP: 4d8c0c15

  MODULE_NAME: usbhub

  FAULTING_MODULE: fffff88008c06000 usbhub

  CUSTOMER_CRASH_COUNT: 1

  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

  BUGCHECK_STR: 0X9F

  Nom_processus: System

  CURRENT_IRQL: 2

  STACK_TEXT:
  "fffff800'04 c 09388 fffff800'03502702: 00000000' 00000000'00000003 fffffa80 ' 09 0000009f d 73060 fffff800 ' 04c093d8: nt! KeBugCheckEx
  "fffff800 ' 04 c 09390 fffff800 ' 034a2e4c: fffff800 '04c094c0 fffff800' 04c094c0 00000000'00000000 00000000'00000003: nt! : FNODOBFM: 'chain' + 0 x 34050
  "fffff800 ' 04 c 09430 fffff800 ' 034a2ce6: fffffa80 '06cdf5b0 00000000'01642618 00000000'00000000 fffffa80' 097aa901: nt! KiProcessTimerDpcTable + 0x6c
  fffff800 '04c094a0 fffff800' 034a2bce: 0000034f 'c591e29e fffff800' 04c09b18 00000000'01642618 fffff800'0360 d 588: nt! KiProcessExpiredTimerList + 0xc6
  "fffff800 '04c09af0 fffff800' 034a29b7: 0000011a ' 68920ac3 ' 01642618 0000011 0000011a has ' 68920 has 32 00000000'00000018: nt! KiTimerExpiration + 0x1be
  fffff800 '04c09b90 fffff800' 0348feca: fffff800 '0360ae80 fffff800' 03618cc0 00000000'00000002 fffff880' 00000000: nt! KiRetireDpcList + 0 x 277
  fffff800'04c09c40 00000000' 00000000: fffff800 ' 04c0a000 fffff800'04 c 04000 fffff800 ' 04c09c00 00000000' 00000000: nt! KiIdleLoop + 0x5a

  STACK_COMMAND: kb

  FOLLOWUP_NAME: MachineOwner

  FAILURE_BUCKET_ID: X64_0x9F_3_btfilter_IMAGE_usbhub.sys

  BUCKET_ID: X64_0x9F_3_btfilter_IMAGE_usbhub.sys

  Follow-up: MachineOwner
  ---------

  0: kd >! devobj fffffa8009d73060
  Object Device (fffffa8009d73060) is:
  Can not read information from nt shift! ObpInfoMaskToOffset
  \Driver\usbhub DriverObject fffffa80094ffa50
  Current PRI 00000000 RefCount 2 Type 00000022 Flags 00003040
  DevExt fffffa8009d731b0 DevObjExt fffffa8009d73bb0 DevNode fffffa8009d7b550
  ExtensionFlags (0 x 00000800)
  Unknown flags 0 x 00000800
  AttachedDevice (top) fffffa8009663880 * WARNING: unable to verify timestamp for c:\windows\system32\drivers\sptd.sys
  ERROR: Module load completed but symbols can be loaded for c:\windows\system32\drivers\sptd.sys
  \Driver\ACPI
  Queue is not busy.

  I would say to uninstall the application that has installed the driver c:\windows\system32\drivers\sptd.sys, maybe it is Daemon Tools or Alcohol 120%.

  Then, uninstall the c:\windows\system32\drivers\sptd.sys - see "How can I remove driver SPTD on 64-bit operating system?" in the following link:

  http://www.duplexsecure.com/en/FAQ

  Similar question in the following thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/the-computer-has-rebooted-from-a-bugcheck-the/2a0b354e-4FEA-4349-b88f-eb4b10199380

• My computer randomly gave me a blue screen, the error message "DRIVER IRQL NOT LESS OR EQUAL (Wdf01000.sys).

  Original title: driver error

  They just showed me an error on my computer. I am currently running Windows 8. I was in the middle of games on Steam and my computer randomly gave me a blue screen. He told me that "DRIVER IRQL NOT LESS OR EQUAL (Wdf01000.sys). It restarted and now I'm on that's fine, but I was wondering if there is anything I can do to prevent and what should I do to remove if it's going to be a recurring problem. Thank you.

  Here is a list of the help page instructions:
  «' ' ' Exact error message: DRIVER IRQL NOT LESS OR EQUAL (Wdf01000.sys)»»» "
  -Your program and Version: don't know what to put here.
  -Your operating system and Version Windows 8
  -Your browser and the Version of Google Chrome Version 28.0.1500.72 m
  -All soft/hardware you have recently installed or removed - None.
  -Any recent changes that have been made to the system - None.
  -What you did to solve the problem of Google there as the error message recommended, read a few results, thought I would ask here.
  Specification of the computer if necessary:
  HP - Sleekbook 15.6 ENVY "
  AMD - processor A10
  -DDR3 SDRAM
  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  
  

  WE NEED AT LEAST TWO FILES DMP TO SPOT TRENDS AND TO CONFIRM THE DIAGNOSIS.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are if you are unsure if you are, you are not) a

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.

  * Zip up the copy (compress)

  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  Link to find out how to download below.

  http://www.WikiHow.com/use-SkyDrive

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.

  * On the Advanced tab, click Startup and recovery... Settings button.

  * Make sure that automatically restart is unchecked.

  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).

  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.

  * OK your way out.

  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32

  Go to 'file', 'save' and download the PDF is saved with the DMP

  System specs are extremely useful then please include everything you know.
  
  
  Blue screen view and that crashed are often wrong and should only be used in case of emergency...
  
  
  You can learn more about BSOD here
  
  
  
  
  Team Zigzag3143.com  

• How can I restart my Dell Inspiron 6000 with blue screen STOP errors: OXOOOOOO24 (OX8A583A5O, OXCOOOO102, OXOO19O2O3, OXOOOOOOOO)

  I can't follow the recommended steps: disable or uninstall etc because I have the only way I can get the screen out of the blue is off. When I restart, the screen is unresponsive to F1 or F8 or options offered reboot - it automatically by default the blue screen message.

  How to do screen out of the blue?

  What should I do to begin the process of recovery by using the reinstallation CD?
  Thank you

  These should be useful:

  Description of the Windows XP Recovery Console for advanced users
  Recovery of Windows XP using the Recovery Console

  When you get to the first audit of recovery for the file Console ntfs.sys such as described in article 1.  If you cannot change the type of file NTFS.sys CHKDSK /R and press .  You can run the command without having to log on to the console.  Be patient, it may take some time chkdsk to finish, it can take hours for the command to complete, there is no way to cancel the order after that you will deliver, just give it time and let run until the end.  DO NOT stop or unplug the computer to cancel the chkdsk command, this may cause more damaged drive.

  John

• Blue screen STOP error: 0 x 00000050 [0xE4489414 0 x 00000001 0x8054BFD2 0x00000001]

  First of all, I got the blue screen error a few days ago. I left my computer and works fine while I went to school, when I got home, it rebooted and frozen to the diagnosis of the BIOS screen. I turn it off and restarted again, and before windows could load up, he got a bluescreen and restarted. Once more, he froze in the diagnosis of the BIOS screen. I didn't know what was going on, so I unplugged my computer and reset the BIOS by removing the battery, and it put it back again. Then I plugged in the computer and it starts. It loaded windows, and I logged on. Windows has worked for about 10 minutes before he got another blue screen of the same type. The screen flashed by too fast for me to read. He said something about 'Memory error'.

  I tried to restart the computer, and he hung up on the screen of the BIOS again, so I reset the BIOS again and was able to open a windows session. I thought I might have a virus, so I start Microsoft Security Essentials and started a full analysis. 5 minutes later, I got the blue screen again. After this third blue screen, nothing I tried would let me connect you. I have reset the BIOS again, tried the last known good configuration (which has worked for 3 minutes) and I tried to start in safe mode. Nothing has worked. Finally I said a few expletives, re-formated my HARD drive and reinstalled windows Xp. It worked well until everything has been done, and when everything was finally set up and running, 20 minutes later I got the blue screen again. I gave up and left the computer to sit for a day, while I thought about what to do. Last night, I turned on it and hey presto, it works again.

  It worked for about 6 hours, then I disconnected and close. This afternoon I turned it on and it worked for about 2 hours, then I got a new Blue error screen. This time, the error remained on the screen long enough for me to write:

  STOP: 0 X 00000050 [0XE4489414 0X00000001 0X8054BFD2 0X00000001]

  PAGE_FAULT_IN_NONPAGED_AREA

  He made a memory dump, and then rebooted normally. To log in again, I got this:

  System has recovered from a serious error:

  BCCode: 1000008e BCP1: C0000005 BCP2: BF8B173F BCP3: B3BE4C3C BCP4: 00000000 OSVer: 5_1_2600 SP:3_0 product: 768_1

  He asked me to send an error report, so I sent off the coast, including the info dump and system memory. So far, I've been connected for about 45 minutes now without any problems. I had previously looked up the error memory and found a bunch of answers that don't really solve my problem. I have installed new equipment last year and the 4 GB of RAM I have in my system is much more than I ever use. I looked at the papers in computer management and found only an error, but it's because after I reformatted my computer, all the previous 'memory' error logs are now gone. Looking at the logs, I also found this error which has repeated every time my computer starts:

  AMLI: ACPI BIOS is trying to create an illegal memory OpRegion, starting to address 0xaabbccdd with a length of 0 x 400. This region is located in the operating system's protected memory address range (0x100000 - 0xdfedf800). This could lead to instability of the system. For technical assistance, please contact your system provider.

  I don't know if this error is related to my other problems or not. The strange thing about all this, is that these problems only suddenly came with none of these errors that occur before about 3 days ago. I also noticed undeclared my CD-Rom has a bad block of memory. I don't know why this product is no longer, because I bought brand new CD a year ago and have any errors with it so far.

  I don't really know what is happening, but I intend to test my RAM and buy a new key if none of them produce the 'memory error' once again, but so far, the computer is running somewhat normally, which is better than nothing. Any advice you have would be great.

  Thanks for your time,

  SLIM

  Much better and you are doing very well.

  Your video driver looks good, your sound is a bit out of date (the latest from Realtek is 5.10.0.6194).

  See the Readme for Realtek from here and see that the most recent driver is 5.10.0.6194, but if it was what he usually come in BSV.

  http://www.Realtek.com./downloads/downloadsView.aspx?langid=1&PNid=14&PFID=24&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  You can check your NVIDIA drivers on the NVIDIA website:

  I use the NVIDIA site and let their scanner online take a look at your video card and see what he suggests for drivers and consider their analysis if they offer a new driver.

  It is recommended to run the scan NVIDIA with Internet Explorer.

  Here is the address of the NVIDIA page:

  http://www.nvidia.com/download/Prescan.aspx?lang=en-us

  Read the instructions, and then click the GRAPHICS DRIVERS button to start the scan.

  I'd do the RAM test, and since you have a genuine XP bootable installation CD, you can start it and choose to enter the Recovery Console and run chkdsk/r as follows:

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same thing you see in the Explorer folder C:\WINDOWS.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the command prompt.

  Start by checking the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  If you get a BSOD, we look deeper into the crash dump files which mean you must download this file "skydrive" share the thing they have here.  If you wish, you can go ahead and download the latest files from 5 dump for the practice.  I need practice too since I'm not a skydriver.  BSV has the information in pink in the lower pane of the form, but it is not in the general report.  Sometimes it NLY shows XP files in the upper part and there is probably nothing wrong with them.

  http://windowslive.com/online/SkyDrive

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!