Blue screen Vista sp2
Hello
Have you added a hardware or drivers updated recently? Check Control Panel - Windows
Updates to see if all drivers have been updated it just before what is going on has begun.
For 7f - this could be a problem of material such as uncomfortable cards or memory, while there are
other causes. Power electric low could also lead to this. Use the troubleshooters above and below
and when you get to the drivers and memory sections refer to my next message below and then
return if necessary troubleshooting services
If a PC remove ALL power. Opening the case, remove and reinstall all memory cards and ALL
cable (try not just to close) on both ends if they are accessible and on the device ends if not
(remove the cables and the resettlement of help them to eliminate minor corrosion).
If a laptop or a PC, you will need to take a shop (not BestBuy or other BigBox stores) or your
Support of the machine system.
----------------------------------------------------------------------
BCCode: 7F 0x0000007F which is the same as 0x1000007F
UNEXPECTED_KERNEL_MODE_TRAP bug control has a value of 0x0000007F. This bug check indicates that the Intel CPU generated a trap and the kernel could not catch this trap.
This trap might be a bound trap (a trap the kernel is not allowed to capture) or a double foul (an error occurred during the processing of an earlier fault, which always results in a failure of the system).
Parameters
The first parameter that is displayed on the blue screen indicates the number of trap.
The most common trap codes are the following:
- 0x00000000 or division by zero error, indicates that a DIV instruction is executed and the divisor is zero. Memory corruption, other hardware problems or software failures can cause this error.
- 0 x 00000004, or overflow, occurs when the processor executes a call to an interrupt handler when the overflow (OF) is flag set.
- 0x00000005, or limits check fault, indicates that the processor, then executing a BOUND instruction, determines that the operand exceeds the specified limits. A BOUND instruction ensures that a signed array index is within a certain range.
- 0 x 00000006 or Opcode not valid, indicates that the processor attempts to execute an invalid instruction. This error occurs generally when the instruction pointer is corrupted and point to the wrong address. The most common cause of this error is hardware memory corruption.
- 0x00000008 or Double fault, indicates that an exception occurs during a call to the previous exception handler. In general, two exceptions are handled in series. However, there are several exceptions that cannot be handled serially, and in this case, the processor signals a double fault. There are two common causes of a double fault
Cause
0x7F bug check occurs after the installation of a faulty or incompatible hardware (including memory) or if installed hardware fails.
A double fault can occur when the kernel stack overflows. This overflow occurs if multiple drivers are attached to the same battery. For example, if two file system filter drivers are associated to the same stack and then again the recursively of file system, the capacity of the battery.
Solve the problem
Troubleshooting: If you have recently added the material to the computer, remove to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. Run the diagnostics of material that does not have the system manufacturer supplies to determine which hardware component.
The scanner memory is particularly important. Faulty or incompatible memory can cause this bug check. For more information on these procedures, see the manual of your computer. Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.
If the error appears on a newly installed system, check the availability of updates for BIOS, SCSI, or card network controller. These updates are generally available on the Web site or the hardware manufacturer BBS.
Confirm that all hard drives, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.
If the error occurred after the installation of a new or updated device driver, you should remove or replace the driver. If, in this circumstance, the error occurs during the startup sequence and the system partition is formatted with NTFS, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console in order to access the file.
Also to restart your computer and press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.
Overclocking (setting of the CPU to run at a speed higher than the nominal specification) can cause this error. If you have overclocked to the computer that is experiencing the error, return the CPU to default clock speed setting.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error. You can also disable caching memory BIOS to try to resolve the problem.
If you have encountered this error during the upgrade to a new version of the Windows operating system, the error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version. If possible, remove all third-party device drivers and system services and disable all antivirus before upgrade you. Contact the software manufacturer for updates of these tools. Also, make sure that you have installed the latest Windows Service Pack.
Finally, if all of the steps above do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can also cause this error.
BCCode: 7F 0x0000007F which is the same as 0x1000007F<-- read="">
* 1304.html http://www.faultwire.com/solutions-fatal_error/Run-a-System-diagnostic-Utility-supplied-by-your-0x1000007F-
======================================================
------------------------------------------------------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm
MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html
-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
as information such as error information and STOP codes
IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.
As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002
or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000
It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.html
BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.
You can do without if needed fail or the Vista DVD command prompt mode
or Options of recovery if your system is installed by the manufacturer.
This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx
You can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228
The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html
-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.
Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm
How to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html
How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx
-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233
Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htm
Understanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692
Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033
-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.html
This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx
I hope this helps.
Rob - bicycle - Mark Twain said it is good.
Tags: Windows
Similar Questions
-
Driver_irql_not_less_or_equal blue screen Vista and can not restart
My PC Win Vista (not sure if 32 bit or 64) continues to display blue screen. Today, he continues to display blue screen when starting, and I can not even accept F8.
Here's what it shows the blue screen before. Hope you could give me some advice what I can do next. Thank you!
A problem has been detected and windows has been shut down to preventdamage to your computer.
DRIVER_IRQL_NOT_LESS_OR_EQUAL
If this is the first time you have seen this Stop error screen, restart
your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is installed correctly.
If this is a new installation, ask your hardware manufacturer or software
the windows updates, you might need.
If problems continue, disable or remove any newly installed or
software. Disable the BIOS memory options such as implementing caching or shading.
If you need to use Safe Mode to remove or disable components, restart your
computer, press F8 to select advanced startup options, and then select
Safe mode.
Technical information:
STOP: 0X000000D1 (0X00000000, 0X00000002, 0X00000000, 0X855F7395)
nvstor.sys - address 855F7395 base at 855F3000, DataStamp
46671a 61
Hello
nvstor.sys is a Nvidia video driver.
Think video drivers especially if it may be others. Refer to the section of driver in my generic bluescreen
methods of troubleshooting below. BIOS, low and antispyway/antivirus/security chipset drivers
programs may also cause this. Check the resolution of problems and when you get to the section driver view
for generic methods in the next message and then back to the if necessary troubleshooting tool.Look in the Event Viewer to see if something is reported on.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm
-------------------------------------------------------------------------
My troubleshootter of bluescreen generic, when you get to the section driver go to the next message, then
return to this one.Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
information on all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-----------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
Unable to boot error on blue screen vista window
Hello
I use windows vista sp2 on the computer and am unable to initialize properly. I am at a loss for what to do.
That's what happened. My computer became infected with a nasty virus, so I tried to boot into safe mode. However, I got a blue screen with an error message that says:
"A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS SHUT DOWN TO PREVENT DAMAGE TO YOUR COMPUTER."
IF IT IS THE FIRST TIME YOU'VE SEEN THIS ERROR SCREEN RESTART YOUR
COMPUTER. IF THIS SCREEN APPEARS AGAIN FOLLOW THESE STEPS:CHECK FOR VIRUSES ON YOUR COMPUTER. REMOVE ANY NEWLY INSTALLED HARD DRIVES OR HARD DRIVE CONTROLLERS. CHECK YOUR HARD DRIVE TO ENSURE IT IS PROPERLY CONFIGURED AND COMPLETED. RUN CHKDSK /F TO CHECK FOR HARD DRIVE CORRUPTION, AND THEN RESTART YOUR COMPUTER.
"I want to reformat my computer for Window XP, but after installation of window will display this error and once I started my pc this error appears again...". PLS help... Thank you...
jpaul08,
If your system has been infected then the best thing to do is to format the HD ANS reinstall factory default. According to the PC that you have, you must have a recovery partition or the recovery disk (most use partitions these days). When start you on the recovery media factory be sure to only select the 'Factory Restore' which will erase the disk and reload the operating system. The only way that you can switch from Vista to XP is now if the recovery media XP or you own a valid copy of XP retail. Mike - Engineer Support Microsoft Answers
Visit our Microsoft answers feedback Forum and let us know what you think. -
Windows Update KB3069114 causes a blue screen Vista
The latest updates for Windows from September 2015 started causing blue screens on my Vista desktop, and after repeating uninstall and reinstall I think, that the problem is caused by KB3069114.
All this experience?
Any chance of a fix for the problem in the near future?
I just downloaded and installed the latest driver for my graphics card. I hope that the plant will be gone now [after] KB3069114 installation.
I would like to know what happens, OK?
-
Please help with my error on vista blue screen:
Product
WindowsProblem
Stop unexpectedlyDate
22/01/2015-18:37Status
Not reportedSignature of the problem
Problem event name: BlueScreen
The system version: 6.0.6002.2.2.0.768.3
Locale ID: 1033Files helping to describe the problem (some files may be is no longer available)
Mini012215 - 01.dmp
SysData. XML
Version.txtAdditional information about the problem
BCCode: a
BCP1: BADFFFF4
BCP2: 00000002
BCP3: 00000001
BCP4: 81CCABDF
OS version: 6_0_6002
Service Pack: 2_0
Product: 768_1If I did it properly, copies of the report of problem files are available here - https://onedrive.live.com/redir?resid=4C455702F4C80FA! 113 & authkey =! AKjYLr1ao53jkKI & ithint = % 2cdmp
I tried a restore my computer to factory image, but the error is returned. I tried uninstalling recent updates but the chance either. Help, please!
Norton is always present, and fortunately, there is no indication that Microsoft Security Essentials has been installed or which could have exacerbated the problem.
Bugcheck A, {badffff4, 2, 1, 81ccabdf}
WARNING: Unable to verify timestamp for NAVEX15. SYS
ERROR: Module load completed but symbols cannot be loaded for NAVEX15. SYS
WARNING: Unable to verify timestamp for SRTSP. SYS
ERROR: Module load completed but symbols cannot be loaded for SRTSP. SYS
WARNING: Unable to verify timestamp for C:\WINDOWS\SYSTEM32\DRIVERS\SYMEVENT. SYS
ERROR: Module load completed but symbols could not be loaded for C:\WINDOWS\SYSTEM32\DRIVERS\SYMEVENT. SYS
Probably caused by: NAVEX15. SYS (NAVEX15 + 679a 7)All modules in bold above, are all components of Norton. Please uninstall Norton!
-
Unable to boot to HARD drive or disc - blue screen Vista: 0 x 50 or 0x7E
I can't start Vist from my drive hard or with the installation disc. Boot from the HARD drive gives a blue screen with the error 0x000007E code and boot from the drive allows me to launch the recovery program, but once I click NEXT for the first time, it goes to a blue screen with error code 0 x 0000050.
I saw a lot of people have had these errors when the computer is running, however, I'm not able to start somehow, not even in safe mode, last known good configuration, etc.. I also tried to clear the CMOS with no luck.Any help would be appreciated.It starts very well when I got to work last night, but won't do a thing tonight.Hey Ross,
Unplug all external devices (except keyboard and mouse) and check if it can boot up to the desktop in all modes.
If this is not the case, contact the manufacturer of the system for more help. -
Closing with error blue screen Vista computer
My computer guard stop, blue screen gives a reference to the device driver and a kernel stack. Also the following in my reports: problem event name: MpTelemetry
Signature of the 01:2152759308 problem
Signature of the problem 02: not specified
Signature of the problem 03: ScanFile
Signature of the problem 04: 3.0.8107.0
Signature of the problem 05: Microsoft Security Essentials (EDB4FA23-53B8-4AFA-8C5D-99752CCA7094)
Signature of the 06 problem: not specified
Signature of the problem 07: unspecified
The system version: 6.0.6002.2.2.0.768.3
Locale ID: 2057Can someone point me in the right direction to solve this problem.
Hello
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
Check out these utilities to see if information may be collected:
It is an excellent tool for displaying the blue screen error information
-Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
and displays information about all accidents of a table.
http://www.NirSoft.NET/utils/blue_screen_view.html-------------
MyEventViewer can be verified at the time of the blue screen (BSOD) within a second or so of the
time of the BSOD to provide more information about the possible cause - see TIP.MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
Set it for a bit before and after the time of the BSOD.
http://www.NirSoft.NET/utils/my_event_viewer.html------------
AppCrashView - free - a small utility for Windows Vista and Windows 7 that displays the details of all the
application goes down has occurred in your system. The information breaks down is extracted from the .wer
the files created by the Windows Error Reporting (WER) of the operating system component of each
time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
text/html/csv/xml file.
http://www.NirSoft.NET/utils/app_crash_view.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
Good evening
I seem to have a problem that certainly goes over my head. My computer works but at the start, a blue screen appeared with technical information.
STOP: 0X0000008E (0XC0000005, 0X8D2867BD, 0XA8F0D69C, 0X00000000)
mfeavfk.sys address 8D2867BD base at 8 266000 date stamp 4fc63e68
Data collection for the dump
Dumping physical memory to disk: 100
Dump completed
Check with the hardware vendor for updates to the bios.
Disable the bios memory options such as implementing caching or shading.
I checked the Microsoft Community website and see similar but not identical problems that others have experienced.
I would appreciate any advice. However, my computer knowledge is limited.
Thank you
Bob
E-mail address is removed from the privacy *.
The offending file was mentioned in your original error (this is rare). It was mfeavfk.sys. Find the file (probably in c:\windows\system\drivers).
Find the files listed and check the properties of the files by right-clicking and choosing Properties and then details. After return the name of the product
.
To quickly find files in windows
Click Start - All Programs - Accessories - right on command prompt and choose Run as administrator. Type
Dir c:\mfeavfk.sys/s/a
It should tell you it's part of the MacAfee Antivirus program.
Your only real option is to update or upgrade the program to a version that is not defective.
You can ask https://community.mcafee.com , as they may have more specific advice.
-
I have a HP m7690n with system to dual-boot windows xp and vista. XP works fine, but Vista crashes as soon as I use the keyboard. crash dump mem.to drive 80 Driver_IRQL_NOT_LESS_OR_EQUAL error help. Also, I use vista with no problems until I use the keyboard and I've updated to the latest driver
Hey, I think your keyboard drivers are corrupt. Try using the screen keyboard and if nothing past the problem is with the driver.
Remove the driver in Device Manager.
Turn it back on.
It will reinstall automatically.
Try to use your keyboard in Mode safe also.
Check your system for Windows Vista configurations and also your diet. And if not correct, then the problem may be because of that.
-
blue screen Vista BCCode c000021a
Hi all
I have dell INSPIRON 1525
with the Windows Vista operating system
Last few months I am facing Aproblem this unexpected shutdown
and then I restart my laptop I get an error cattle mantion below:
Product Signature:
Problem event name: bluescreen
The system version: 6.0.6002.2.2.0.768.3
Local ID: 1033
More information about the problem:
BCCode: c000021a
BCP1: A1BAE1D0
BCP2: 00000000
BCP3: C0000001
BCP4: 00100460
OS version: 6_0_6002
Service Pack: 2_0
Product: 768_1
Files helping to describe the problem:
c:\windows\minidump\mini111610_01.dmp
c:\user\AppData\Local\Temp\WER_48422_0.SysData. XML
c:\user\AppData\Local\Temp\WER878.tmp.version.txt
I'm not what it is
and how I can solve this problem.
Please and me to save my laptop.
Bug Check 0xC000021A: STATUS_SYSTEM_PROCESS_TERMINATED
Bug STATUS_SYSTEM_PROCESS_TERMINATED control has a value of 0xC000021A. This means that an error has occurred in a subsystem essentially user mode.
http://msdn.Microsoft.com/en-us/library/ff560177%28VS.85%29.aspx
Cause
This error occurs when a subsystem of mode user, such as WinLogon or the Client Server Run-Time Subsystem (CSRSS), irremediably compromised and security can not be guaranteed. In response, the operating system goes into kernel mode. Microsoft Windows cannot run without WinLogon or CSRSS. Therefore, it is one of the rare cases where the failure of a user mode service can stop the system.
Incompatible system files can also cause this error. This can happen if you restored your hard disk from a backup. Some backup programs may skip restoring system files which they determine are in use.
Resolution
Resolve an error in the user-mode device driver or system, third-party application service: Because the bug 0xC000021A control occurs in a user mode process, the most common culprits are third-party applications. If the error occurred after the installation of the new or updated device driver or service system, third-party applications, the new software should be removed or disabled.
If the error occurs during the system startup, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the WindowsAdvanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time. If the error is not resolved, try to manually remove the offending software.
Please also, start Windows Explorer and navigate to the C:\Windows\Minidump folder. Then, copy the files to your desktop, zip dmp dmp all in 1 zip file and download the zipfile to your Skydrive folder [1] public and post a link here.
André
"A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/
-
Blue screen Vista Kernel data Inpage Error
Apparently, I have some bad sectors or something on my HD. By knowing the BSOD, is it possible to partition the wrong part of the HD, reformat a different partition and reinstall Vista to eliminate the problem? I have enough room to do it, but want to know if it will work until I'm in the effort of all.
Hello PJMaxw,
If there is a bad sector on the disk, then it is likely that there are more.
With the bluescreens seeming to be varied and random, I recommend you contact Dell for assistance with the material side of this.
Let us know what they say.
Best regards
Matthew_Ha
-
Blue screen in Vista 7 just after the login screen
We get a blue error screen 7th on Vista 64-bit SP1 right after the login screen appears. The blue screen immediately goes, and system restarts (or sometimes just hangs). I was not able to find the codes of the 7th in the research:
(took a picture of the screen...)
STOP: 0x0000007E (oxFFFFFFFFC0000005, 0xFFFFF80002325C87, 0xFFFFFA60165BE3E8, 0xFFFFFA60165BDDC0)
I am able to boot in safe mode. Do you have a chkdsk C: /F and which did not help. Do you have a repair system using the Vista startup disk and that did not help. Went to safe mode and MSCONFIG and position the clean boot and that did not help. I tried to update to SP2 and unable to complete safe mode.
The ideas and the sage advice would be greatly appreciated.
Pete
Hello
Pick up the pieces after a computer breakdown - see what to do if Windows won't start correctly
http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crashCheck this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available from the OneDrive or other
file -sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.Adding files to your OneDrive
http://Windows.Microsoft.com/en-us/Windows-8/getting-started-onedrive-tutorialA disk - sharing files and folders and change the permissions
http://Windows.Microsoft.com/en-us/onedrive/share-file-folderZIP or download the content of the C:\Windows\minidump
Use OneDrive to upload collected files
-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
The system has RAID? If so, it's also very suspicious.
This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
methods in the next message and then return to the if necessary troubleshooting tool.Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
spyware/security programs.When you get to the pilot and sections of the memory of the troubleshooter check the following message to
update drivers and memory test and then return to the troubleshooter if necessary.------------------------------------------------------------------
BCCode: 7F 0x0000007E which is also 0x1000007E
Bug Check 0x7E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
Bug SYSTEM_THREAD_EXCEPTION_NOT_HANDLED control has a value of 0x0000007E. This bug check indicates that a system thread threw an exception that the error handler did not.
Important info if you received a STOP Code
If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.
These actions could prevent a mistake like this does not happen:
- Download and install updates for your computer from Windows Update device drivers.
- Scan your computer for computer viruses.
- Check your hard drive for errors.
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED parameters
The following settings appear on the blue screen.
To view the settings, click on this link.
http://msdn.Microsoft.com/en-us/library/ff559239 (v = VS. 85) .aspxCAUSE
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
interpret, you must identify which exception has been generated.Common exception codes are:
0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates an unaligned data reference was encountered.
0 x 80000003: STATUS_BREAKPOINT indicates a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.
For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
the Microsoft Windows Driver Kit (WDK).Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques.- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the
- Reference of the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
(the address of the exception) must identify the driver or function that caused the problem.If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .In case of exception code 0 x 80000002, the trap frame provides additional information.
If you do not know the specific cause of the exception, consider the following questions:
- Hardware incompatibility. Make sure all new hardware that is installed is listed in the
- List of Microsoft Windows Marketplace tested products.
- Service driver or defective peripheral system. A service driver or defective peripheral system can be
- responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
- and IRQ conflicts can also generate this error.
If a driver is listed by name in the bug check message, disable or remove that driver. Disable
or remove drivers or services that have been recently added. If the error occurs during startup
sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
in Safe Mode, you must start the computer by using the Recovery Console to access the file.If the problem is associated with Win32k.sys, the source of the error may be a third remote
control program. If this software is installed, you can remove the boot of the computer service
by using the Recovery Console, and then by removing the offending system service file.Check the system log in Event Viewer for additional error messages that might help identify the
device or the driver that generated the bug check 0x7E.You can also disable memory cache BIOS may try to resolve the error. You should also
Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
For more information about these procedures, see the manual of your computer.The error that generates this message may occur after the first reboot during Windows Setup, or
Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
space, reduce the number of files on the disk drive hard target. Find and delete any temporary
the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
contain fragments of file saved to disk scans. You can also use another hard drive with more drive
free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="" this="">
* 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-----------------------------------------------------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard event viewer
Windows. TIP - Options - Advanced filter allows you to see a time rather
of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen of the.
http://www.NirSoft.NET/utils/blue_screen_view.html
death ' crashes and displays information about all accidents of a table.
FreeBlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Does not work
tell all possible driver issues).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
-
Blue Screen at shutdown - STOP: 0x0000 008F (Vista Home Premium 32-bit)
Whenever I stop, I get a blue screen of death. I had not used my computer for a few months, so I do not remember if the hardware or software has been added.
I put the BSOD to stop so I could write the codes - I googled them came but with nothing.
Here is what says the BSOD:
STOP: 0x0000 008F (0 x 0005 C000, 0 x C4E3, 0 x AC2E DC0C, 0 x 0000 0000 8261)My system runs Vista Home Premium (32 bit) on a bridge 5442 with 4 GB of Ram and an Intel Core 2 CPU 4400 running 2.00 Ghz
Any help or advice is most appreciated.
Thank you kindly!
Marilyn PHello
Two main causes of this blue screen video drivers and BIOS - check with system manufacturer site for
View of the adapter (video) and BIOS, then on site of the manufacturer of the device for the last video. There may be other drivers
in order to check there. DISABLE the auto-pilot plant as those who are older and if updates Windows suggests
a pilot just HIDE. Antivirus is another possibility.See methods of update driver generic in the next message.
BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved .chk , which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
It comes to my convenience store generic bluescreen:
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
information on all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps and happy holidays!
Rob - bicycle - Mark Twain said it is good.
-
Windows Vista, several blue screen errors
Original title: BSOD
Good afternoon
I have the BSOD. Here they are in chronological order:
1 IRQL_NOT_LESS_OR_EQUAL 0X0000000A (0X0000001D, 0XFFFFFFC2, 0X82424EF8, 0X00000001)
2 0X000000c4 (0x000000A0, 0X96AEEA58, 0x995FCEE0, 0x0D99EEE4)
3 0X000000c4 (0x000000A0, 0X968F0DF0, 0x99406EE0, 0x053F1D0A)
4 0X000000c4 (0x000000A0, 0X9A651638, 0x993C4EE0, 0x10AB65F8)Additional information:
Windows Vista Service Pack 2
DualCore Intel Core 2 Duo E8400 3000 MHz (9 x 333)
Gigabyte GA-G33M-DS2R (2 PCI, 1 PCI-E x 4, 1 PCI-E x 16, 4 DDR2 DIMM, Audio, Video, Gigabit LAN)
DDR2-800 DDR2 SDRAM
BIOS: Award BIOS v6.00PG Modular
Could you help me... don't really know what to do...
Hello
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65----------------------------------------------------------
BCCode: 0a 0x0000000A
Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
The video driver or something affecting it would be questionable.At the end of this message, I'll post a bluescreen generic and in the next convenience store
How do to update the drivers and BIOS but also to check memory message.-----------------------------------
BCCode: 0a 0x0000000A
Cause
This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.
The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.
If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.
Solve the problem
If a kernel debugger is available, get a stack trace.
To resolve an error caused by the faulty device driver or service system, BIOS
- Restart your computer.
- Press F8 to character-based menu that displays the choice of operating system.
- In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.
To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool
- Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
- Try disabling the cache in memory of the BIOS.
- Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
- Make sure that the latest Service Pack is installed.
- If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
- For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.
If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.
Comments
Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.
BCCode: 0a 0x0000000A<-- read="" this="">
* 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-==================================================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
Driver vista Power State failure Blue Screen of Death
Please help me I think it's that I'm doing this... What is going on.. I have replaced the ram and video card, but has seen this problem before I did it... also just reinstalled windows vista... Please help https://skydrive.live.com/redir.aspx?cid=7cbac7e09f2ecb07&resid=7CBAC7E09F2ECB07! 105 & Thierry = 7CBAC7E09F2ECB07! 101 & authkey =! AEE_idLDpolnFKY
Hello
Those showed all CAUSE as a Windows component that means something different it led into error.
Then ZIP or RAR the actuall minidump files and download them on SkyDrive and post a link here for us
to analyze the other.Check this KB:
The shutdown process does not terminate and you receive an error message on a computer that is
running Windows Vista or Windows Server 2008: "Stop 0x0000009F"
http://support.Microsoft.com/kb/972109----------------
You use Roxio or Nero programs? They have been known to cause this problem even
If they worked well for a long period of time. If so check with their support.Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
Troubleshoot BlueScreens - answers top 3 (+ 1 more).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from thereZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65----------------------------------------------------------
References to Vista also apply to Windows 7.
This "might" be a power problem, even if this isn't the most common cause - in this case
It seems that the PSU could be the fault.9F is probably a driver issue. Security/antivirus/antispware programs can also cause these issues.
Have you added the recent devices or the updated drivers - don't forget to check in the Windows updates to see
If a driver has been updated before this happen. This can also be caused by a loose card or cable
and even a weak power supply.This error means that a driver does not properly support the power state. Check in Control Panel - device
Manager to ensure that the drivers are not stop during sleep - double-click adapter - NETWORK adapter
and WIFI - healthy and others - tab power management - uncheck allow the computer to turn off.
Maybe the only has a problem.Start - type in the search - find MSCONFIG in top - right, click on – RUN AS ADMIN
General tab - tick this box start Diagnostic - APPLY / OK - REBOOT
Try it now. If the computer still blue screens thinks that video driver. Otherwise think the card NETWORK, Wifi, sound, or...
(and it might still be video interacts with something else). See following message for my
generic driver update methods.BCCode: 9F 0x0000009F<-- read="" this="">
* 1167.html? order = date http://www.faultwire.com/solutions-fatal_error/Driver-Power-State-Failure-0x0000009F-==========================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
http://www.NirSoft.NET/utils/blue_screen_view.html
hangs and displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
Maybe you are looking for
-
How to start firefox in safe mode automatically from the command line
This is for Windows XP, firefox 19
-
ZBook 17 G2: (SOVLED) lack of ZBook 17 G2 drivers
After a new installation of Windows 7 and downloading and installing the drivers as much as possible from here: http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=6978822 & swLangOid = 8 & swEnvOid = 4059 I'm still showing 2 unknown device
-
Re: Satellite C660-2E1 - BIOS Lock out
I have a C660-2E1, that locked me with a BIOS password, can help any one with the way you reset the Bios password? Any advice would be appreciated.Thanks in advance.
-
How to run several programs simultaneously on the same block diagram
Hi all I want to run three instruments simultaneously on the same schema. One is a control position for linear drives, other is an optical micrometer and the third is a digitizer card. When using tabs of the controls, the linear actuator Vi is the on
-
Black screen during the connection (Vista) very well in safe mode...
OK, so yesterday I run my registry any clean my computer was fine... when I turned on it today it says windows had not been turned off correctly and to check for errors... I looked at this process as I always do, as it is rare for this to happen. I n