Brain status anomalía ESXi

Similar Questions

• Status unknown heath ESXi

  Hello.

  I use Dell openmanage essentials to manage our servers, ESXi included. However, for our ESXi servers (which are all 5.1.0 build 914609) I am unable to get the State of health. Servers appear under the folder/umbrella "VMware ESX Servers" in the devices view and I can see that all installed virtual machines, including servicetag and various other HW information.

  That's what I did:

  -Installed the VIB OMSA via vCenter Update Manager (dell repository)

  -Check the installation of the OMSA VIB and restarted host

  -Configuration of the SNMP traps

  -Active CIM OEM

  -Discovered server although the Management Protocol

  I have configured separately by WSMAN and 'check status' discovery via SNMP.

  Through the troubleshooting tool that comes with Dell OpenManage Essentials, I am able to connect successfully to the server by using OMSA remote Enablement, audit of Port, SNMP and WSMAN.

  I'm so stuck. Someone has an idea of what could be bad?

  Kind regards

  Nils Rune Hjelle

  The trick seems to be deleting all the beaches of discovery and enter it again. The State of health is now very well. Not the ideal solution to be honest, but at least now it works.

  Thanks for all your comments.

• How to get the material status of ESXi host of external surveillance system?

  Hello!

  I've got hardware ESXi host information (for example, CPU, disk, etc.)

  that I want back outside a vCenter/ESXi for an external monitoring system.

  I really really slighty possible via Powershell saw...

  Thanks for your help!

  Hello

  the link that I commented, explian how to monitor the status of the ESXi hardware by using the cmdlets for powershell CIM 3.0.

  Not the virtual machines

  This, will you?

  Check this code from the link, you should notice that connects to an esxi host, not virtual machines:

  import-moduleCimCmdlets

  2	$ipaddress="10.20.177.15"

  3	$HostUsername="root"

  4	$CIOpt= New-CimSessionOption-SkipCACheck -SkipCNCheck -SkipRevocationCheck -EncodingUtf8-UseSsl

  5	$Session= New-CimSession-Authentication Basic -Credential $HostUsername -ComputerName $Ipaddress -port 443-SessionOption$CIOpt

  6	Get-CimInstance-CimSession$Session-ClassNameCIM_Fan

  Best regards

  Pablo

• Daily ESXi NTP healthcheck service

  Hello

  We have the need to monitor the config and status of our ESXi hosts the NTP service and tried some of the solutions mentioned on this blog. The last one I tried was posted by "jaydo123" but seems to be for a single post.

  Our goal is to interview guests and view state on a web page that could be controlled by our events team

  Example of the info we need.

  Hostname, NTPservice State, NTP server and the current time on the esxi host.

  We will have the page to refresh every hour.

  Has anyone ever had the need to do and if so any suggestions on getting this right.

  Thank you

  Johan

  Take a look on Script: check the status of ntp and time on your ESX Servers.

  It requires the use of plink to retrieve the current date of the ESXi servers.

• Book of Espaço storage nao atualiza

  BOM dia colegas,.

  Estou com um problema aqui em um Servidor ESXI5.

  Ele estar com devido a perto of ability limited movi some archives of uma Máquina virtual para outro ESXI e um Espaço liberei.

  As ao see acontece no storage, o Espaço nao Mudō status. Este ESXI esta utilizando Disco SAS como storage locations.

  Are some principle para scanear OU uma atualizacao forcar no storage?

  Desde ja Agradea§o a bonitos,.

  Marcello Rogério.

  WP não creio as exsista, mas certamente you encontras algo na internet. Igualmente, a snapshots tua VM ainda esta com (quando o nome back instant acaba em - 00000 X hard, e porque esta sober discos), e AO WHAT PARECE, realmente, o land you marcou nao your sendo used. SE quiser, try mover pasta ele pode, e is a seguir running VM (reset ela para ter certeza) ai sim PODES apagar o land tranquilo.

  Instant os Apagandos e os don't discos nao books, certainly you will liberar Espaço none kills VMFS.

• 5.1 ESXI health status: unknown

  Hello

  I have a HP PL DL380p G8 and ESXI 5.1 with essential kit. Everything was ok, but after months, I got in the health configuration tab: unknown.

  Bit is all ok, server is running, and I don't find any hw problem.

  Why is-status unknown health?

  Thank you.

  Hello

  Restart management agents.

  How? Look here:

  Management for the restart ESXi (ESX 3i) agents

• ESXi 5.1 status host HA is showing that the election

  Hello

  I have a node 4 ESXi 5.1 HA and DRS Cluster. Recently, I replaced all these hosts SSL certificates and prior to this activity, I had turned off the AP. Now, after replacing the hosts SSL certificates - when I am allowing the PA on the cluster, 1 single ESXi host is projection status of HA - ' Running (Master) and rest all three hosts are 'Election' HA status.»

  Tried to re - install the HA agent on the host, but issue still persists. Also tried the re - configure the AP on hosts ESXi, deactivation and activation of AP on the cluster, but no luck.

  Can someone help me for that to be resolved.

  Thank you

  KC

  Hi all

  Thanks for all your response.

  Problem is solved without the help of the HostReconnect.pl script. I followed the steps below and now all ESXi hosts demonstrate normal HA status.

  (1) put the host in Maintenance Mode. Unplug and remove from the vCenter server.

  (2) restart the management through DCUI Agent.

  (3) uninstalled the HA agent using the command line.

  (4) add the host to the Cluster.

  5) out of Maintenance Mode.

  By following these steps - correctly configured the AP on all four ESXi hosts. Now a single host is show as master and rest three hosts are displayed as slaves HA status.

  Kind regards

  KC

• Get status on ESXi 5.1 high availability Agent

  Hello everyone!

  Anyone has any script to check the status of Agent of ESXi 5.1 high availability?

  
  Thank you

  Rafael Nunes

  Hello

  OK, try this, I check on my side and that's ok.

  Get-VMHostService [ESX] |  Where {$_.} Key - eq "vmware-fdm"}

  

  And you can have a status of running.

  Kind regards

  Julien.

• vCenter 4.1/ESXi 4.1 material status "Communication error with the server.

  I am slot that a brand new installation of vCenter with two new installs of ESXi 4.1 connected on it. I use on Dell PowerEdge 2950 s ESXi servers. I tired the customized version of Dell and vmware ESXi vanilla version. My host vCenter is Windows 2008 R2.

  In vCenter, the two server ESXi, any version of ESXi, I run, I get "Communication error with the server" error when I click the tab hardware state. No data appears in the hardware status tab.

  Only suggestion of Dell has been updated with firmware/BIOS on the server level. I did and it did not help.

  Anyone has any suggestions or ideas what would cause this?

  I had exactly the same problem what is to have everyone on this thread.  I finally called VMware support.  It is certainly a problem with Tomcat.  Apparently, during my initial installation of tomcat server vCenter (on a Win2k8R2 vanilla Server / unreleased) na not create a database file.  The vCenter Server uninstalled eventuall tech and went through the Setup again.  For some reason any Tomcat created db it's good the second time.  After installation, it takes about 5 minutes for the db should be created.

  On Windows 2k8R2 it is located here: C:\Program Files\VMware\Infrastructure\tomcat\lib\xhiveConfig\data

  The name of the comic is VcCache-by default-0. XhiveDatabase.DB

  My server didn't have one at all.  The relocation has created, at the beginning it is 0KB in size.  After 5 minutes, it grows up to 25, 600KB.

  Everything in my vCenter works now correctly.  I'm on 4.1.320137

  I hope this helps.

  Dave

• Emulex a Manager command not showing material status of esxi hosts

  Hi all

  We use Emulex CMO for the updated release of the HBA firmware via vcenter, 4 Esxi host (all in the same cluster) do not display details of HBA in the CMO and we were not able to update the firmware on these hosts.

  Hand this group, we can see the details of HBA and update firmware for all other hosts in different cluster

  Any help or suggestion will be useful.

  Ajay.

  Check if the port TCP 5989 (incoming and outgoing) is open to allow CIM transaction traffic pass between the host ESX and vCenter Server and vice versa.
  DMZ host is managed by a server vCenter Server outside the DMZ. It may occur if the port 5989 is blocked, even if ESX and vCenter Server are in the same network.

  Check you via Telnet utli

  REF vmware Kb: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1013080

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

  Manmohan Boitel

  VMware SME

• ESXi 6.0 - SSH Command to check the status of running tasks

  Hi all

  What I'm trying to do is quite simple, but do not know whether it is complex or not.

  I'm checking the State of a task via SSH. You know, like that of the lower part of the vSphere Client where it shows you the task and the status of it. I need to monitor the % of the deployment of the MV EGGS in various hosts via a script but can't find the command to do, but would be nice to be able to check any task and its status.

  What I found so far:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1013003

  But that was not helpful at all. I tried but could not get information about the deployment.

  Thank you all for any help or lead, you may have.

  Hello world

  I found the answer myself, which was indeed in the URL I posted.

  I just had a problem to see a small change in orders.

  In step 7, it says task_info and I wrote get.tasklist with the task identifier.

  Thank you guys and I hope at least that it might help someone trying to do what I'm doing and reading VERY well orders, haha

  Kind regards

  Martin

• Get ESXi IPV6 host status

  Hi all

  I need a powercli script to see if ESXi host IPv6 is enabled or not.

  A way to achieve

  Get-VMHost | Select active Name,@{N='IPv6 "; {E = {$_.ExtensionData.Config.Network.ipV6Enabled}}

• VMWARE ESXi 4.1: Add a DATA store via a new 4 TB SATA HARD drive

  Hi all
  Thank you for all the support and the good work that you provide!

  I'm not a VMWARE specialist.
  I'm on a DELL T610 with a VMWARE ESXi 4.1. Several virtual methods machines operate on a RAID5 grap with a PERC6i controller.
  The CDROM SATA drive is visible and usable on the hypervisor.
  In fact, I add a 4 TB SATA (Seagate ST4000NM0033).

  I see my HARD drive in the BIOS and I see too much on the vmware console:

  / dev/discs # esxcfg - mpath - l
  ........
  SATA.vmhba34 - sata.0:0 - t10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC
  The Runtime name: vmhba34:C0:T0:L0
  Feature: t10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC
  Full device name: Local ATA drive 4 TB
  Adapter: vmhba34 channel: 0 target: LUN 0: 0
  The identifier for the adapter: sata.vmhba34
  Target ID: sata.0:0
  Plugin: NMP
  State: Active
  Transport: sata
  .....

  
  Or:

  / dev/discs # esxcfg - mpath - b
  NAA.6842b2b0092e9100141774ac16c2a585: disk DELL Local (naa.6842b2b0092e9100141774ac16c2a585)
  vmhba1:C2:t0:l0 LUN:0 Status: Active Local HBA vmhba1 channel 2 target 0
  
  MPX.vmhba0:C0:t0:l0: Local TSSTcorp CD (mpx.vmhba0:C0:T0:L0)
  vmhba0:C0:t0:l0 LUN:0 Status: Active Local HBA vmhba0 channel target 0 0
  
  T10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC: Local ATA disk 4To
  vmhba34:C0:t0:l0 LUN:0 Status: Active Local HBA vmhba34 channel target 0 0
  
  T10. DP___BACKPLANE000000: Local pregnant DP Svc Dev (t10. DP___BACKPLANE000000)
  vmhba1:C0:T32:l0 LUN:0 Status: Active Local HBA vmhba1 channel 0 target 32

  Or:

  / dev/discs # ls-l
  ........
  -rw - 1 root root 0 3 Sep 15:48 t10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC
  lrwxrwxrwx 1 root root 3 73 Sep 15:48 vml.01000000002020202020202020202020205a315a3138454b43535434303030-> t10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC
  .........

  ===========================================================================

  BUT: I can not add a partion on it:

  Fdisk u t10. ATA___ST4000NM00332D9ZM170___Z1Z18EKC

  I can not Use the graph console of the hypervisor , If I add un storage LUN , Nothing in the list... I can not Add ... I do not see it.

  You have a track for move me? Forums et doc VMware ne not allow me to unlock my brain ()...

  I thank all for your interest and your help.

  ESXi 4.1 disc limit is 2 TB less than 512 bytes, ESXi 4.1 will not recognize more than 2 TB, check for other options as well.

• Failure before brain su Vmware

  Buonasera a tutti,

  Ho tried a search in archivio my non ho trovato nulla, quindi ho pensato di una nuova discussione open.

  Premesso questo piccolo dettaglio, avrei need di monitorare I brain del mio Server su cui e installata the Vmware Esxi 5, con licenza essential version more.

  CI sono sono tutti server linux one could leave it Vcenter che e knew Windows, I wanted to know is it e modo di lo brain dei status links. In linux by vedere IO is UN disco if sta guastando uso my smartctl- a/dev/hda he comando ho discovered che tale comando non su funziona vmware in quanto I server virtuali brain sehen e ovviamente non, I brain substitutes.

  MI chiedevo is dal pannello di Vsphere o anche solo a riga di comando sulla porta ssh c dell 'esxi' e a modo by links Hardware e nello specificio he fail pre dei brain che mi aiuta a understand be un disco if sta guastando oppure e gia guasto.

  Ora of da want possa Sin help came.

  Saluti

  Andrea Giuliano

  Prego

  SE e a Dell, allora it software che devi cercare e Dell OpenManage Server Administrator, da questo you can remotamente monitorare I server, a patto che abbiamo da I VIB drivers:

  http://www.Dell.com/support/drivers/us/en/555/DriverDetails/DriverFileFormats?DriverID=Y0WHR&FILEID=2990390081&ProductCode=PowerEdge-R410&urlProductCode=false

  No Yes honestly is OMSA gratuito o sia a pagamento pero.

  Ciao,.

  Luca.

• get the error message "status.msi".

  After insalling windows XP Pro SP3 yesterday, everything was fine. Today, I turn on the computer and get this continuous message "status.msi" missing. I have accumulated my brain trying to find the file with no luck. Done a repair and still a problem.
  Also in the auto updates SP2 would not up-to-date.
  I need help in the form of simple please...
  Thank you

  Hi Michael6208,

  ·         You get the error message for Windows update?

  Follow these methods.

  Method 1: Perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: For windows, update problem, disable the security software temporarily.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable the antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network at the time the anti-virus software is disabled, your computer is vulnerable to attacks.

  Method 3: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  Method 4: Follow the steps in the article to reset the Windows Update components.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058