Breakpoints do not work properly, cannot preview size.

Similar Questions

• Photoshop Elements 3.0 does not work properly, cannot e-mail pictures of 3.0

  cannot e-mail photos using Vista

  cannot e-mail photos using Vista

  ===================================
  Maybe PhotoShop elements Support could help you.

  Adobe PhotoShop Elements in Help and Support
  http://www.Adobe.com/support/photoshopelements/

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Error: This device does not work properly because Windows cannot load the...

  I get this error message "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) "via a wired connection. And that's the Microsoft 6to4 adapt #7 and the same card but the #4 one.  Are these drivers or another file that I could use DL?

  Hi JasonBedgood,

  1. Once you get the error message?
  2. did you of recent changes on the computer?

  This error occurs if the required driver is not installed or the driver is damaged.

  I suggest that you update the driver for the device and check.

  How can I update the driver for network card on the computer

  1. click on Start, click Control Panel, and then double-click System.
  2. click the tab hardware , and then click Device Manager.
  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click continue.
  3. click on network adapters to expand.
  4. under network adapters, double-click the entry for Microsoft 6to4and then click driver .
  5. click on Update driver software.
  6. follow the Wizard update software driver to update the driver for NICs .

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the device driver update did not help then check the link below for one of the thread with the question and try the steps mentioned by Lionel Chen on January 9, 2008
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Scaling fonts does not work properly - 125% is to double the size of 100%

  Hello

  I just got a new monitor with a resolution of 2560 x 1440, and now I have problems with the font size. The setting of 100% is extremely low, but then when I put the setting to 125%, fonts are at least double the size. A value of 110% is also significantly higher than 100%. I also note that in the window where I put the scaling, the sample policy shown at 100% is longer so that I can see actually in the system.

  Here some screenshots:

  http://www.the-ninth.com/demo/fontscaling/100Prozent.PNG
  http://www.the-ninth.com/demo/fontscaling/100Prozent_2.PNG (comparison with the actual size settings dialog box)
  http://www.the-ninth.com/demo/fontscaling/110Prozent.PNG
  http://www.the-ninth.com/demo/fontscaling/125Prozent.PNG

  Y at - it an explanation of why the setting of 100% is so small?

  Cheers, Robert

  Hello

  I understand that you are facing problems with the police in your computer.

  I suggest you consult the following Microsoft articles and check if it helps you to set the size of the correct font on the computer.

  Method 1:

  You can read these articles Microsoft and check if it helps.

  Make the text on the screen larger or smaller

  http://Windows.Microsoft.com/en-us/Windows7/make-the-text-on-your-screen-larger-or-smaller

  If the problem persists, I suggest to change the resolution of the screen and check if it helps.

  Change your screen resolution

  
  http://Windows.Microsoft.com/en-us/Windows7/change-your-screen-resolution

  Method 2:

  If the problem persists, I suggest you to update the video card drivers and check.

  To do:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows/Update-driver-hardware-ISN

  You can also see the following article for more information.

  Get the best display on your monitor

  http://Windows.Microsoft.com/en-us/Windows/getting-best-display-monitor#getting-best-display-monitor=Windows-7

  Hope this information is useful. Please let us know if you need further assistance.

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• SD card is not working properly after installing windows 10

  I have a MacBook Pro (retina, 13 inches, early 2015) with EL Capitan 10.11.5 and after I installed 10 windows using bootcamp, everything worked fine at first, but after I deleted my part of windows and then installed windows 10 the second time, the SD card is not working properly. She mounts only if the computer shuts down first, and then start. If I take the laptop directly, the SD card will not rise. The same thing happens when I switch systems using a control option key or bootcamp Center where when I switched to another system, the SD card that was mounted on the old system does not appear in the new system. I was trying to solve this problem remove the part of windows before you reinstall it again once, so I found that after I deleted the windows part, the problem is gone and it reappeared after installing windows 10 even once. I also found that after I installed windows the total volume of hard drive (128g front) became 121g.

  Hello LorinMax,

  Thanks for this info and choosing the communities Support from Apple. I know the importance of your work with your Macbook Pro SD card!

  If I understand correctly, you cannot use your SD card, unless you stop and then restart. Because this behavior started when you installed Boot Camp, I would start with the following steps:

  1. first of all, start by repairing your hard disk in disk utility to correct the unexpected problems that could be the cause of this behavior.

  Disk utility (El Capitan): a disc repair

  2. use Mode without fail to start up your Mac so that it performs certain checks, remove files from the system cache, check your startup disk and trying to fix problems if necessary directory.

  Try safe mode if your Mac does not end commissioning

  Graphics performance limited in recovery of OS X or in safe mode

  3. According to Boot Camp Installation & Setup Guide, you may need to back up your personal data and reinstalling OS X, then reinstall Windows via Boot Camp and related support files.

  Boot Camp Installation & Setup Guide

  Backup of your Mac hard drive

  OS X: on OS X Recovery

  See you soon!

• Satellite Pro M10 - infrared does not work properly

  Hello

  I have a Satellite Pro M10 and my infrared does not work. I downloaded the zip file with the drivers from this site. Then, I uninstalled and reinstalled, but it always happens in the Device Manager under "unknown - SMC IrCC - Fast Port infrared (IR Module: HP). (with an exclamation point). When I look at the properties it says under device status:

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click Troubleshoot to start the troubleshooter for this device.

  However, under Driver Details is said:
  C:\windows\system32\DRIVERS\smcirda.sys

  I extracted the zip file in my home directory of c:\downloads\infrared.
  whatever I do, it does not now. It worked when I bought it, but I have too many things on the system for a new installation. Which brings me to another question. Is it possible to re - install windows without losing all your data, etc.? I did it with other systems (95,98) Windows. But it seems that the Toshiba recovery disc means any wiping.

  Thanks in advance for any help.
  Chris

  Hello

  If your HARD disk contains two partitions and you have saved the data on a second you can reinstall the operating system on the first partition using recovery DVDs.

• Mat * one years (uj-840) DVD player does not work properly

  The Mat * one years (uj-840) DVD player does not work properly.
  A symptom of the problem is that the icon does not appear in 'my computer '.
  more and she does not recognize the CD.

  I went to the properties of the drive through Device Manager and saw the following message is displayed:

  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)
  Click Troubleshoot to start the troubleshooter for this device. »

  Following the instruction of the troubleshooter, I tried to update my driver through
  Device Manager, but it tells me that the current driver is the more up-to-date version.
  In the properties of the drive, I found that my driver version is: 5.1.2535.0

  What is a simple problem that has a solution?
  I don't see other actions to find the root of the problem.

  Thank you

  I hope this article can help you - http://aps2.toshiba-tro.de/kb0/FAQ8101LA0000R01.htm
  Check it out!

• Satellite A200 recovery does not work properly

  Hello.

  After making a few changes in the partition settings (when installing Ubuntu) Vista does not load (after the loading screen appears a black screen and nothing happens). I changed the Vista partition only by expanding its size.
  I try to reinstall Vista and set parameters of origin with product recovery cd, but with the same result - after screen to communicate on loading the filesystem appears black screen and no action is performed. I changed the boot on a dvd/cd device.

  I guess that's a problem with the parameters of partition, but don't know how to solve. Now, I have an original score with Vista (extended) and the other in the rough. How should I change it to properly run product recovery?
  I'll be grateful for any help.

  @ Salim Al-Ghaithi

  This error message is not known to me, but it seems that the application that has been installed on the recovery CD can not work properly.

  It's not easy to say why it happens maybe dysfunctions of restore CD or you partition the HARD disk is not going.
  I recommend you begin with formatting the entire HARD drive. You must also remove all partitions on HARD drive and then try to use the recovery CD and start the installation.