Broken screen - problems of transfer of files on USB stick due to the "read-only".

Similar Questions

• Windows XP - a problem to transfer big file from laptop on an external hard drive

  I have a problem to transfer large files (mail.pst - zipped file - 5Gbyte) of the laptop (Dell Latitude D630) on an external hard drive (WD 320 G - FAT 32) where each time, I got the message "there is not enough free space on the disk" although I did successfully drive clean on both sides and there is enough space on both sides (not less than 25 GB).

  Also, I did a checkdisk command and he succeeded, and I use Windows XP

  I did several tests to resolve and in the end, I found that I convert the format of external hard drive FAT 32 to NTFS, and then I could successfully transfer the file.

  I used the following commands:

  (1) command line then chkdsk to repair bad sectors

  (2) convert the command line to change the format to FAt 32 to NTFS

  Note: For Windows xp, "convert" command will not delete the files from the hard drive

• Cannot get rid of the read-only file attribute

  I have a folder on my PC which is marked read-only.  The Setup program seems set up like that.  If I right click on the folder and go to 'Properties' there is a grey checkmark on "read only".  If I have it uncheck the box, and then click OK or apply then OK, it remains unalterable (the grey tick comes).  There is no hidden file in the folder.

  How can I fix it?

  Contrary to all logic of common sense, the 'Read only' attribute, as shown in the Properties screen has absolutely nothing to do with 'Read only' when it refers to a folder in Windows XP. In fact, it indicates that it is a custom folder.  A full explanation can be found here:

  "You can not view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7"
    <>http://support.Microsoft.com/kb/326549 >

  You don't mention exactly what your "problem" is with this folder, so I can not develop too much more than that.

  HTH,
  JW

• I am trying to remove the read-only in a file of windows vista program

  Hello

  I'm having a problem with the program files in Windows Vista. I have a file that I need to be able to write to and I can't get out of the read-only mode. Can someone help me with this please?

  Thank you.

  You really shouldn't be messing around in the Program Files folder unless you REALLY know what you are doing, because the wrong action can cause a lot of damage to your programs (more than one in some cases).  You experience trouble intentionally caused by Vista.

  But assuming you want to do anyway for some reason, the said problem as a Teen geek is ownership and permissions.  They are particularly tight on the programs folder (and hard to get around even for people experienced in this sort of thing).

  You must you give full permissions and take ownership of the files or the folders that you intend to work with.  You may need to change the permissions of the parent due to inherited permissions folders.  You may also use the advanced permissions option to deal with special permissions (maybe change some while they are not inherited or others in order to provide the right permissions as well as the main permissions screen.  I don't know how long until you go to appropriating, but start with everything that you need and work upward only when necessary.  Here are a few guidelines for permissions and lines taken possession that should help you:

  To view your permissions, right-click on the file/folder, click Properties, and check the Security tab.  Check the permissions you have by clicking on your user name (or group of users).  Here are the types of permissions, you may have: http://windows.microsoft.com/en-US/windows-vista/What-are-permissions.  You must be an administrator or owner to change the permissions (and sometimes, being an administrator or even an owner is not sufficient - there are ways to block access (even if a smart administrator knows these ways and can move them - but usually should not because they did not have access, usually for a very good reason).)  Here's how to change the permissions of folder under Vista: http://www.online-tech-tips.com/windows-vista/set-file-folder-permissions-vista/.  To add take and the issuance of right of permissions and ownership in the right click menu (which will make it faster to get once it is configured), see the following article: http://www.mydigitallife.info/2009/05/21/take-and-grant-full-control-permissions-and-ownership-in-windows-7-or-vista-right-click-menu/.

  To resolve this problem with folders, appropriating the files or the drive (as an administrator) and give you all the rights.  Right-click on the folder/drive, click Properties, click the Security tab and click on advanced and then click the owner tab.  Click on edit, and then click the name of the person you want to give to the property (you may need to add if it is not there--or maybe yourself). If you want that it applies to subfolders and files in this folder/drive, then check the box to replace the owner of subcontainers and objects, and click OK.  Back and now there is a new owner for files and folders/player who can change the required permissions.  You can change now switched to read-only (even if the main folder indicates that they are always read-only - you can access yourself as the owner).  You can keep them in read-only to other users, customers and administrators even (although they can support themselves and access, if they wish, and it is really not that you can do to stop it except protect the file with a password by using a 3rd party product.)  Here is more information on the ownership of a file or a folder: http://www.vistax64.com/tutorials/67717-take-ownership-file.html.  To add take ownership in the menu of the right click (which will make it faster to get once it is configured), see the following article: http://www.howtogeek.com/howto/windows-vista/add-take-ownership-to-explorer-right-click-menu-in-vista/

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to change the read-only, write protect status of files?

  Original title: change the State of the files.

  I have problems deleting files.  I need to know how to change the status of the files: e.g. "read-only, write protect, etc."

  Hi fbanks4,

  1. were you able to remove the files before?

  You can read the following article and try the steps to change the status of the read-only files:

  You cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7

  http://support.Microsoft.com/kb/326549

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I can't turn my photos because I can't disable the 'read only' attribute of my files.

  Whenever I go into the Properties uncheck the read-only attribute of my files, it won't let me, but he will return back as soon as I click on ' OK. "

  I tried to change the property, as well as the opening of full control.

  I'm already administrator.

  It happens even when I create new folders on my desktop. It it automatically read-only, and I am able to uncheck with him coming back after I click OK without worrying.

  Help, please.

  The photos are from my phone. Open them in the image viewer and I'm just turning them using that, or good right click to rotate.

  This also happens with the new cases, I create and save all the images that I have on my computer.

  The images themselves are not read-only. The folder attribute is the problem.

  Again, there is no attribute of read-only files.

  If you use an iPhone, the photos can contain metadata that preventing rotation.

  See this thread.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cant-rotate-some-photos-in-Windows-7-but-can/3a809845-9144-4BB1-9bb3-ab4f5b856524

• I can't uncheck the 'Read only' attribute with success a Program Files (x 86) folder. Help, please?

  Hello. I have mod Grand Theft Auto IV for pc. Long story short, I have the re - install. There is this called LCPDFR mod that allows you to become a police officer in the game. I need to download this. In order to successfully download this (when I try to download / save, he said "the Publisher of this program could not be verified". it gives me no option to run or something and that's it, apparently because of the problem I put in the title and Description), the root folder "Grand Theft Auto IV" (which is in my "Program Files (x 86)" folder) is not to be 'Read Only' (the 'Read only' checkbox must be deselected in 'Properties'). Do not forget that, under the tab 'security' in 'Properties', for the folder root of "Grand Theft Auto IV", I have administrators / me 'total control '. So, as I said, I uncheck the 'Read only', click on 'Apply', then 'Ok '. I go back in 'Properties' and 'Read Only' is checked as if I had never disabled it in the first place (when I already just did).

  So, in summary, the problem I have is that every time I uncheck "Read only", click on apply, then click ok, and go to properties again, it is always checked when I was already unchecked, applied and then approved it. This continues to be over and over and over again. Please help me?

  PS - I have windows 8.

  I thank you very much for your time and have a nice day!

  Hello. For some reason I'm not able properly to uncheck the 'Read only' attribute of a folder in my "Program Files (x 86)". Whenever I click to uncheck the 'Read only' in 'Properties' (tried several times) and click 'Apply', then 'Ok' and I go back to check it out, it is checked as if I've never disabled it. I have Windows 8. He continues to do this and I don't know why. Help, please?

  ====================================================
  Read-only status is normal for files because Windows ignores the
  attribute. Whatever the question is that you are trying to correct may not
  be associated with the State of the file read-only.

  If you change the attribute read-only folder... What follows
  the article covers Windows Server 2003, XP, Vista and 7... Perhaps it would be
  work for Windows 8.

  (326549) you cannot view or change the Read-only or the system
  attributes of folders in Windows Server 2003, Windows XP, in Windows
  Vista or Windows 7
  http://support.Microsoft.com/kb/326549/en-us

• Remove the read-only attribute from all files in a folder

  How to remove the read-only attribute from all files in a folder. I tried to use the properties and used the attrib command, but all I see is when I right click on the folder, selecting Properties, it shows once again

  

  I followed the forums, but I'm really confused. Can someone help me with this. Thanks in advance

  I would like to start by finding which file is read-only again. This is probably a file as well as a miniature file desktop.ini.  An easy way to find it is to go to the details view, turn on the column heading "Attributes" and search for all files with the attribute value "R":

  In this example, the key of SB file is read-only:

  

• Eliminate the 'read only' files on DVD. Went to properties and clicked off the coast on the 'read only' box, but it does not work.

  Put some files on DVD and then tried to change them.   Receipt message they are 'read only' tried to click on 'read only' in the properties, but this does not work.  The 'read only' is back.  How can we change the files on a DVD?

  In general, once you write multi-utilisations, you can not edit the file.  If you use a rewritable media, you can delete the file and write again.

  DVD writing (burning) is not present natively by XP.  What application you are using, including version?  Support for packet writing?

• Cannot cancel the read-only file attribute.

  I click to clear the read-only and then hit apply to apply it to the folder and all subfolders, and looks like he took command. I closed the window and then reopen it and the read-only attribute is again highlighted. I am the administrator of the computer and I tried to move the folder to another location.

  Read/write attributes are not applicable to files in Windows XP, Vista or Windows 7. That's why you can't change the way you do. If you try to take possession of the file, this is how:

  Appropriating a file or a folder under Windows XP [Q308421] - http://support.microsoft.com/?kbid=308421

  How can I get the Security tab in the folder properties? - http://www.dougknox.com/xp/tips/xp_security_tab.htm
  MS - MVP - Elephant Boy computers - don't panic!

• Cannot complete the 'read only' designation on some files

  Signature the administrator XP, I can't change the 'read only' tab on the records. After I click on the box to cancel 'read only', the computer checks the box itself. How can I get the computer to end definitively the status of 'read only' on selected folders?

  XP does not use the attribute of read/write on records. This is normal. If you try to take in hand, this is how:

  Appropriating a file or a folder under Windows XP [Q308421] - http://support.microsoft.com/?kbid=308421
  How can I get the Security tab in the folder properties? - http://www.dougknox.com/xp/tips/xp_security_tab.htm MS - MVP - Elephant Boy computers - don't panic!

• Will not save file because it is supposed to be read-only, but I'm not read-only.

  Will not save file because it is supposed to be read-only, but I'm not read-only. The file is NOT read-only. I checked by accessing the properties on the file.

  The error message says:

  "The file may be read-only or another user can open. Please save the doent under a different name or in a different folder. »

  Hi farukp69792329 ,

  Please provide the point exact Acrobat & OS version installed on your system. This is the file is saved to the network drive or local. If his backup to disk network suggest you save to local disk.

  If its windows, please disable the preview pane feature.

  If you still get the same message

  Disable the Safe_mode Adobe

  go to Edition-> Preferences-> Security

  Uncheck the box enable improved security.

  Kind regards

  Christian

• When I try to save a document, I get the message "the file is opened by another program or read-only. I need to change the name to save him.

  When I try to save a document, I get the message "the file is opened by another program or read-only. I need to change the name to save him. If I optimize a document, I rename it to save it. If I opened a PDF file of the architect drawings and turn them into fashion landscape so that they are easier to read, I have to rename it. I searched on the parameters to look for something that I could turn off, but I found nothing.

  Make sure that the preview in Windows Explorer option is disabled.

• Toshiba Regza 46VL743G - playing files via USB stick

  Hello

  I have problems with playback music and videos via USB. I tried to format my USB for different file systems (ntfs, fat, ms - dos, for example) and video formats, but the screen is black, I launch the media player.

  My TV has played with MS-DOS Format the photos, but no mp3 or divx/avi files. I run the multimedia player with 'video' the led of the USB stick flashes, but after a few seconds the led turn off (I think that the stick loses power).
  My other TV (LG 55LE7510 55 '') plays all video files and mp3 without any problem (ntfs and video format *.avi)

  Someone has an idea?

  Hey,.

  Have you tried another USB key and the same thing happens with another USB key? Usually, you use the FAT32 format for your USB key. Then the TV will be able to recognize it and all the files it contains.

  According to the specifications of your TV supports jpeg files (USB and SD card), MP3 (USB) and video DivX SD (USB).

• Files on a share network stuck as 'read only' to put the computer to sleep.

  By necessity, I use my 98 computer windows that the file server since tempting to access any shares of Vista will cause Windows 9 X to crash. It is already used as a print from the Vista computer server does not have a parallel port.

  I worked on a Microsoft Word document and subject to frequent interruptions. When I put the computer to sleep before walking away from the keyboard, it isn't properly disconnect the Win98 system. Wake up to the computer, I am unable to save office documents, because they are locked for editing.

  In addition, sometimes even after I close Word or Excel, the system is not disconnected. Even when I stopped all other computers, the Win98 system reports that there are still users connected to the system when I go to stop him so. Is it possible to force the Vista computer to disconnect all network connections before you put it to sleep or stopping then the Win98 system recognizes that no one is online and that all the files will be closed?

  I really don't want to have to close a document that I am in the middle of working on when I have to walk away from the keyboard, but this seems the only solution to the problem. Leaving open is the main reason that I put the computer to sleep rather than stop it. Recording locally is not really a good option because I want files stored in one place, and Vista Home Premium does not support synchronized folders.

  Any suggestions? I already use the Briefcase feature to save documents on a flash drive, do I have to use the drive in question and transfer it to the server through network disks? This seems to beat the goal of a network.

  The affected systems are Windows 98 Second edition and Windows Vista 64 bit Home Premium =.

  Hello

  Win 98 is a former client OS, server to call (or any other OS cleint) is nice, but this does not mean that they can be found on a peer-to-peer network and behave like a real server.

  Under this situation (using Win 98 for a server) it is not advisable to change the files over the network. First copy them to the Vista Edit computer and then synchronize. Return using one of the many free synchronization applications that work on most of the windows releases.

  Example, http://www.snapfiles.com/reviews/Allway_Sync/allwaysync.html

  There is no judgment of network functionality, if the Application is enabled and go to sleep while a file is open on Win 98 it will stay open. Closing the file needs to be done by the application.

  -------------------------

  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  Jack-MVP Windows Networking. WWW.EZLAN.NET