C:\Users\jason wald is not accessible - access denied

Similar Questions

• Drive external drive is not accessible, access denied.

  My computer (Win7 Home Prem) ran chkdsk after an update of windows, probably triggered by ccleaner or glary utilities. My external hard drive was plugged during the update, reboot and chkdsk. The chkdsk command probably checked my coz external HD, I can see folders/paths that were there. The next day I couldn't access my HD due to a mistake, saying: it was not accessible and access is denied. I searched online potential solution and tried the following without success, and they have been applied using an admin account and an admin cmd.

  * Change the permissions and ownership, but the property always says it's impossible to determine the owner.

  * Changed the share permissions.

  * Do you have 'takeown' and a 'icalcs' has changed owner but same error.

  * Check the disk management, drive seemed ok with the letter drive and all.

  * Ran chkdsk /F on both of my C: drive and external hard drive, both completed successfully without error during the analysis and not found bad sectors.

  * Program of Unlocker used to check if player was running another process, found nothing.

  In my computer, it shows the letter drive and NTFS, but not bar showing free space. Properties would show 0 free space / used. Here I can go to cmd and access the content from there. I used the function of 'Explore disk' of glary Utilities and I could see the content and even run mp4/avi files in the player. So I guess the drive and its contents is ok, just that I can't access it through normal means.

  Thanks in advance!

  Rob

  Hi LeBlanc,

  I apologize for the late response and can certainly understand your concern. I appreciate your efforts. As you mentioned that you are not able to access the external drive, and you receive the error of access denied when you connect to your user account, I suggest to try to create a new administrator user account and then try to access the external drive.

  To create a new user account, please follow the steps mentioned in the link below:

  http://Windows.Microsoft.com/en-us/Windows/create-user-account#create-user-account=Windows-8

  Please let us know if the problem persists.

• E:\ is not Accessible - access denied

  Hello!

  Dear all,

  I had a problem.

  I had brought some changes in the properties of the "Local drive E:\. "by going to

  Properties > Security tab > allow / prohibit the access Option

  

  At this point, I chose all deny options and has applied. But after that, now I can not even access I have admin m & a message appeared;

  E:\ is not accessible

  Access denied

  

  I would like to deny access for non admin users keep privacy drive local (e).

  your kindness in this regard will be highly appreciated. Thank you!!

  Hello

  Follow the steps below to remove the genuine users.

  Right click on the E drive and select Properties.

  

  In the window appearing in the above screen shot click on change.

  Once you click on edit, you will see this window.

  

  In this window, you must select the authentic users, and then click on remove.

  Hope the helps of the steps. We know the result.

• I have locked my hard drive and now get this message: D is not accessible access is denied.

  drive hard access denied

  I put the password on my hard drive in windows 7, then I deleted windows 7 and installed windows vista but now when I try to open locked hard drive he said D is not accessible access denied, what should I please help

  Delete all partitions "including the small 100 MB system reserved partition' can install Vista.

  -Partition management utilities-

  Partition Wizard Home Edition: (use the bootable CD version)
  http://www.partitionwizard.com/free-partition-manager.html
  Note: There is also a CD bootable or versions of the bootable Flash drive:
  CD: http://www.partitionwizard.com/partition-wizard-bootable-cd.html
  Flash player: http://www.partitionwizard.com/bootable-flash-drive.html
  Among the features and functions: create partition, Delete partition, Format partition,.
  A partition resize, move partitions, Partition recovery after an accidental deletion,
  Convert the partition, partition Explore, Hide partition,
  Change the drive letter, a partition active Set, Explorer (content display) of the partition.
  Note: To run any task (such as deleting a partition) use the "Pending Operations" box at the bottom left.

  Alternative to Partition Wizard (a bit easier to use, but Partition Wizard and EASUS have almost identical user interfaces)
  EASEUS Partition Master Home Edition (free):
  http://www.partition-tool.com/
  Partition software ALL-IN-ONE and the most convenient hard disk partition manager Kit
  Includes Partition Manager, Disk & Partition copy Wizard and Partition MBR and GUID partition GPT disk recovery Wizard (table) on Windows 2000, XP, Vista, Windows 7 and Windows Server 2000/2003/2008 (32-bit and 64-bit).
  It allows users to resize/move Partition, drive system extend, copy Disk & Partition, Partition merge, Split Partition, redistribute free space, convert dynamic disk, Partition Recovery and much more.

  J W Stuart: http://www.pagestart.com

• c:\ drive is not accessible access is denied

  my hard c:\ drive is not accessible access is denied my restore says system c:\windows\system32\rstui.exe the parameter is incorect I can't change my account I can't download need help

  I fixed it myself without access to drive c and with finding my lost vista cd.  I partitioned a space on my 2nd hard drive were I have installed windows 7 rc that I could find. then I completely lost my vista at startup program but was finally able to access the c drive was I changed the owner and reset the permissions {sweet}, then I downloaded the vista startup and repair cd {freebie} rebooted from the cd, he fixed the restarted start menu and was able to see my vista who temporarily lost started it and I ended up controll full return it downloads updates etc. just as it has done before my vista nightmare now, everything has been left a hard drive #2 I copied everything that was on the vista partition and it moves on the drive c in its own new folder then reformatted the drive d {drive #2] which left me with a clean drive were I was able to bring back every thing and worked.} I ' m sure that there was probably an easier way, but being able to find my vista cd and have very limited access to my vista program there were no alternative short bought another operating system and lose everything that I already had on my computer. "  6 weeks waiting for a response time was bad enough

• Start getting error - 'load - User\Name\Appdata\Roaming\iasnapw.dll - access denied error.

  From the start of my PC (with windows Vista), I always get a message: "load - User\Name\Appdata\Roaming\iasnapw.dll - access denied error" in any case I can still use my PC normally. What does this message and how to resolve this error.

  Thank you
  A. Wahyan

  Hello

  Google who provides virtually no information that suggests it might be the malicious program or a start remains for her entry search

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If the error persists after scanning use this program to out startup

  This utility, Autoruns for Windows, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• Every time I try to acess this partition appears that q:\ is not acessable, access denied.

  Every time I try to acess this partition appears that q:\ is not acessable, access denied. When I try to go on propieties and security it shows me that I'm not aloowed to access and I need the permition. So, when I try this appears current owner: uneble to view the current owner and when I try to change the current owner appears an error indicating that uneble to change the current owner, attentive refused. PE of Hel me please! I already have a few boughy this laptop!

  There was no acess in safe mode and the local drive Q:\

  This means that the disc is created by a third-party software that you have loaded yourself, for example a RAM disk or an encrypted volume.

• E:\ is not accessible access is denied

  My CD and DVD drives are not accessible under one (1) of our user names. All are directors. They work very well and very well with other users (3) autoplay. Device Manager indicates that he not there no problems. I run fix - it, and he said that everything is fine, except that the media are unreadable. I tried several different discs in the two discs and get the same disk error in fix - it. The disks will work perfectly under other user names.

  I'm puzzled. Help me please.

  Hello Urbchguy,

  Thank you for your message.  It is possible that the profile has been corrupted.  Let's try the following:
  Connect to your computer with one of the admin accounts that works properly.
  Click 'Start' > click 'My computer' > navigate to the following folder:
  C:\Documents and Settings
  Rename the problematic profile to add _old after profile.
  example: C:\Documents and Settings\jsmith_old
  And then disconnect and reconnect under the problematic connection.  A new profile will be done, you can then copy the 'old' profile data to the new.
  Please let us know if it did or did not help to solve the problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• c: / is not accessible. access is denied.

  Hello

  I have problems with my diet and I finally pulled money to replace. After you install the new power supply, it starts up and I tried to access my C drive. He came up with the following error:

  "C: / is not accessible." Access is denied. »

  I tried allowing the hidden administrator but has not yet been able to give my user with permission to access the drive.

  Any help is very appreciated.

  Hello

  Thanks for the post.  I suggest you refer to the suggestions in this article.

  "Access denied" or other errors when you access or work with files and folders in Windows

  https://support.Microsoft.com/en-us/KB/2623670

  Please get back to us if the problem persists.

• Q player said... Q drive is not accessible access is denied

  Why drive drive Q say Q is not accessible and that access is denied? The player says it's "Office Click-to-run".

  I went to uninstall click to launch the program, it cancels them at the end and click to run the Application Manager gives the error message

  I tried to uninstall all Microsoft Office Office Starter. But none can do.

  I can't use the Office Starter either. It gives an error message 'Click-to-run configuration failed. Please e-mail me at * address email is removed from the privacy * thank you. Pamela

  See this thread.
  http://answers.Microsoft.com/en-us/Office/Forum/office_2010-office_install/what-is-the-q-drive/4b98ad88-B3F0-4362-B315-1a7bfbf7e4f0

• «Location is not available ~ access denied»

  When I try to open a variety of files in Windows Vista using the offers, I get the followiong: ' there is no location ~ access denied»  This occurs when you try to open the following files only: data of the Application;  Cookies; Local settings; My Documents; Network Neighborhood; Neighbourhood of printing; The latter; Send to; Start menu and models.

  These are the points of junction : hidden, protected operating system files that are not supposed to be accessed by users.

  Each of them points to a folder that is accessible to the user:

  Application data - C:\Users\\AppData\Roaming
  Cookies - C:\Users\\AppData\Roaming\Microsoft\Windows\Cookies
  Local settings - C:\Users\\AppData\Local
  My Documents - C:\Users\\Documents
  Neighborhood Network - C:\Users\\AppData\Roaming\Microsoft\Windows\Network shortcuts
  Print neighborhood - C:\Users\\AppData\Roaming\Microsoft\Windows\Printer shortcuts
  Recent - C:\Users\\AppData\Roaming\Microsoft\Windows\Recent
  SendTo - C:\Users\\AppData\Roaming\Microsoft\Windows\SendTo
  Menu - start C:\Users\\AppData\Roaming\Microsoft\Windows\Start Menu
  Models - C:\Users\\AppData\Roaming

• Restoration to a corrupt user or copy corrupted to a newly created user. I am not allowed access to corrupt the user of another administrative user.

  When I try to copy the files from the user to a new user, the corrupt user is inaccesable when I click it.  I'm another user of the admin access.  I restarted the computer.  Does anyone have any suggestions?

  I encountered this problem immediately after removing an accessory program Apple ITunes that I have not used.  I did it to clear up disk space.  This has happened also when I got a low disk space to open the user.  I could open another admin user account and free up enough disk space to open the user.  When I try to connect to the corrupt user, it connects me to another user called (name.value of initial user followed a string of alpha-numberic characters)

  Thank you

  Hello Cscoler,

  Corruption of the profiles can be caused by malware, by repeated interruptions due to file system corruption and bad hardware issues. Did you run any malware removal software?

  When you created a new user account, have you configured it as an administrator? Do you receive error messages when you try to open a session in the corrupted profile, such as "the system has recovered from a serious error or user profile is corrupted"? When you log in the corrupted profile, are you able to view your data?

  Thank you

  James

• < drive >: \ is not accessible. access is denied.

  Hello

  I created a VM installed vm tools. so I decided to add a disc more to the system (windows 7 x 64 bit).

  When I format the drive. disc is created and formatted normally but when I want to access it, watch somehow I have no right.

  user with which i m trying to access is domain administrator and UAC is disabled.

  I deleted this record and created another, same scenario. I can't access the created disc.

  any ideas?

  Since you in a field, there are group policies restrict your access?

  Perhaps you could use diskpart to verify if the drive is in read-only mode?

  My drive is read-only, help! -Ask the Core Team - Site Home - TechNet Blogs

• C:\Users\User\my document is not accessible

  Hello

  I brought 2nd hand computer in a recycled computer store Windows, most of the things are very good except the C drive & I can't pass as an attachnment any photos or info I see on internet e-mail

  Hello

  Thanks for posting your question in the Microsoft community.

  You are unable to access the folder my documents, hence are unable to attach files to e-mail messages. I would like to know if it is incorrect.

  To understand the issue better supply more information.

  1. What do you see in the folder my documents? You are able to see all the files?
  2. You are able to download files to the folder my documents?
  3. You did changes to the computer before the show?
  4. When you try to access my documents, is there a code error or message?

  Check out the link:

  Suggestions for a question on the help forums

  http://support.Microsoft.com/kb/555375

  Provide more information so that we can offer you methods to solve the problem

• SQLFire: Failed to start and then can not close-"Access denied" & "could not start the"sqlfire"database

  I ask a question, expanding to another thread 'http://communities.vmware.com/message/1884835', on the start-up and stop SQLFire.

  My topography has four servers, two locators, and two servers (Server 2 SQLFire each) on which the database is deployed.  When you start the batch, without no history running, all right.  Adding and removing servers in the cluster, also seems to work very well.  However, when the whole of the system, its stopped by sqlf shut-down-all, it starts up, things go wrong.

  I met the same problem described by the called thread, that is, it seems to be an addiction to data - which is not resolved.  I start locators first, one at a time.  When one starts, data dependence becomes apparent.  The Locator seems to start, but the sequence goes in a loop around the data dependence.  When you try to stop the same Locator, he returned in a "stopping" State, where it does not recover.  Try a reboot, translated by [A SQLFire Locator works already in the directory "C:\SQLFire\Locator"].  The "stoppage of sqlf Locator", producing a further: "timeout for SQLFire Locator at the stop, the status is: SQLFire Locator pid: 4956 status: stop ' results; and the "sql shut-down-all:, throws a long error that includes:" java.io.FileNotFoundException: shut_down_all.log (access is denied) "and 'Could not start the 'sqlfire' database'. '.  Both of these appear to be the crux of the matter.

  I don't know what data it is dependent, because I haven't added all the data that will be persisted.  However, the system starts with default records.  I tried to check if these default disks are required, which seem not to be and I'm leaving for the partition and replication information, to read when the system starts / begins.  I can't understand why locators cannot start without the database, without any dependence on the data, and also why the system seems to require a sequence to start.  Is that not the purpose of SQLFire, i.e. a solution supporting the cross, which can be started in any sequence of old?  If an operator needs to get this bad, for a production system, should be that the entire solution be recharged from external sources, and that could take awhile.  It would seem, once the system in this state, i.e. the dog chasing its tail, he doesn't get, and I have to delete all the bookmarks and servers and launch all to reboot from external data sources.

  I'll be dilly, or is it a problem in general, experienced by others?

  I would be grateful for any comments, and if you could indicate the respective documentation, as I struggle to establish a correlation between the problems of documentation, even Google hits, when it encounters any problems with SQLFire.

  I appreciate your time and efforts.

  Hello

  I checked the docs and they are not accurate on information in Windows when using the cmd shell. The ampersand does not work correctly when called from a shell, Cygwin, or on UNIX/POSIX systems. Will get corrected.

  Please, use the start command to start in the background of a single command window / batch script:

  beginning of "locator" cmd /c sqlf locator...

  beginning of "server1" cmd /c sqlf server...

  etc.

  Add option/min to start the minimized for example windows cmd start 'locator' / min cmd /c sqlf locator beginning...

  Or launch each 'start-up of the sqlf Locator', 'sqlf-start server' etc to separate windows command prompt.

  Thank you

  Felicia

  Post edited by: SumedhWale