Calculator chart value vs Epoch

Similar Questions

• Calculation of value tx rx bandwidth

  Hello

  Can someone help, how to calculate the bandwidth utlization of "sh int' details..?"

  Can the percentage will get calculated from values tx rx... ?

  I use the lease line 4 Mbit/s.

  FastEthernet0/0/0 is up, line protocol is up

  Material is FastEthernet, address is 001a.6c70.4b14 (bia 001a.6c70.4b14)

  Description: Internet connection

  The Internet address is 1.1.1.1/30

  MTU 1500 bytes, BW 4000 Kbit, DLY 100 usec,

  reliability 255/255, txload 31/255, rxload 120/255

  Encapsulation ARPA, loopback not set

  KeepAlive set (10 sec)

  Full-duplex, 100 MB/s, 100BaseTX/FX

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Final cleaning of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0

  Strategy of queues: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 828000 bps, 111 packages/s

  5 minute output rate 498000 bits/s, packets/s 92

  788931865 packets input, 4036778275 bytes

  Received 398 broadcasts, 0 Runts, 0 Giants 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  Guard Dog 0

  entry packets 0 with condition of dribble detected

  571607354 packets output, 3639639717 bytes, 0 underruns

  Thanks in advance,

  Kind regards

  Emilie Thakare

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose.  Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

   

  There are several ways to do it, but if your link is 4 Mbps, use the statement of bandwidth on the interface and the value 4000 (I seem to remember that he uses K, if it is not correct value would be 4000000).

  So when you look at the tx or rx loads, those are the load reports.  for example, 128/255 = 50%, 64/255 = 25%.

• You cannot change the chart value axis when there are several types of graphics in a single diagram

  Illustrator can do graphics with bars and lines / columns, for example in the docs:

  

  http://help.Adobe.com/en_US/Illustrator/CS/using/WS3f28b00cc50711d9fc86fa8133b3ce158e-8000 .html

  However, when I create a chart like this, I seem to lose the ability to manually set the y-axis using 'override calculated values.

  To reproduce this problem:

  1. Create a chart as in the example, with bars and an axis on the left, lines and an axis on the right. Unlike the example, don't fix the numbers as well as the lines align perfectly - have a go until just less than 20, a up to a little less than 250, therefore it do not markers and the number of divisions on each side.
  2. Try to make the markers and numbers of divisions to the height, so in fact, the side that is going up 20 going up to 25 and has the same number of divisions on the other side.

  Everything I have tried does not work:

  • If I select the entire chart and go to the "Chart Type", I can not set the options for the value axis. In earlier versions, it's gray, in CS6 I can access, but clicking on 'OK' does nothing.
  • If I select the entire chart and chose the type of a chart, I can set options for the axis value, but that the selected chart type, and then applies the entire table.
  • If I use the direct Selection tool to select one of the series and open the "Chart Type" options, changing the options of the y-axis has no effect
  • If I use the direct Selection tool to select all series that share an axis and open the "Chart Type" options, changing the options of the y-axis always has no effect
  • If I use the direct Selection tool to select the Group of ticks axis itself, or the axis line and groups of ticks axis themselves, of axis labels, axis and graduations of the axis line, or axis labels, axis line, graduations of the axis and series of related data, etc., by changing the options of the axis also has no effect

  It seems that this feature is broken and it seems that the example in the manual has been carefully chosen to use a rare combination of numbers where it would actually look right.

  I thought about it. Like everything to do with the horrible ancient neglected graphic Illustrator tool, it is ridiculously clumsy and involves the caution around what is shamefully bad programming for a professional expensive product.

  It is timing - to do things in a sequence of rigid counterintuitive that seems not to work then meets at the end:

  1. Create the chart but, for now, keep all the same chart type. If you've already set to have different graphics types, put the same thing for now.
  2. Select the entire chart and in the main window of Chart Types, set the value to "Both sides" axis
  3. In the drop-down menu, there should be a left and right axis (or top and bottom...). Set the parameters of the value axis for these now. It will look like it does for a single axis, because it will not change the other axis - naked with her...
  4. Select the data series you want to use the other axis using group selection. Go to graph Type and the value of the y-axis to the other and set the chart type that you want. All of a sudden all be put in place.
  5. If you need to change the settings for the value axis, select the entire chart, set the whole chart type to a chart, change the appropriate value axis by choosing it from the menu drop down and the re - apply types of graph as above.

  (the bug is - it should not necessary to set the graphic object to only have only one chart of type in order to access the axis options of value for two different y-axis)

• Calculations using values in the channels

  Is there a way to make simple calculations (addition/subtraction) of single values selected channels?   New user DIAdem, so I'm not at all familiar with the scripts.  Looks like it should be a simple command, and I'm right on it.

  Thank you

  Shannon

  Hello Shannon,.

  It seems to me that you do not want to add two or more 'cells' (to use the jargon of Excel) together.

  DIAdem manages data such as channels, not individual cells. If the approach to add two cells in DIAdem works like this:

  The variable SMC allows you to access a 'cell' in a channel, using the following sequence parameters:

  ChD (X, Y)

  where X is the line number of the table of channel, and Y is the name of the channel (column) or the number of the cell you want to access.

  For example, this expression here calculates the result of adding the value of line 2 of the channel called "Temperature_1" and the channel called "Temperature_2" of the example data set that takes over at the start of tiara. In this case, R1 is a real internal DIAdem variable that stores a single value.

  R1 = SEC (2, Ch("[4]/Temperature_1")) + SMC (2, Ch("[4]/Temperature_2"))

  The calculation above can be entered in the "Calculator" which is available in MODE of DIAdem and DIAdem analysis in the toolbar.

  

  I hope it's useful, please let us know if you have additional questions.

  Otmar

• data in the chart values

  Hello
  
  How to display the values of stacked - Vertical data - model rtf?
  
  Thank you

  http://winrichman.blogspot.com/2010/05/chart-data-values.html

  Re: Option to display data in charts
  Re: Need help - advanced graphic coding

• Calculating the value of output with custom scale

  Hello

  I defined a custom in MAX scale.

  I want just to calculate the value of an input applied with this scale value.

  Process is simple:

  X-online custom-online output value scale

  in the process of

  Is there a way to do it simply (reminder: custom scale can be linear, polygon, table etc...)?

  Looks like you might need to check the interpolation
  http://zone.NI.com/reference/en-XX/help/371361J-01/GMATH/interpolate_1d/

• Waveform chart - values y get

  Hello

  I'm working on a group project where my team member gives me a graph of waveform as output of their under vi.  I need to use the amplitude (values of y) on the graph of waveform for my part.  I think I'm supposed to use "array index" to do this, but I'm not sure how.  Could someone maybe give an example? Thank you

  Hi Sara,.

  This is because the data type of your waveform graph is in fact a cluster, if you turn on context help (ctrl + H) and move your mouse over the wire, you will see the components of the cluster (two doubles and an array of doubles).

  You can use Ungroup to extract various components (the table is what you want). If you move your mouse over the graph of a waveform with context-sensitive help you activated, you can see what each part of it.

  The first double is x 0 (the starting x position), second double delta x, and the last part is the table of amplitudes (values of y). At the bottom of the context-sensitive Help window is a detailed help link that will lead you in aid where you can get more information on the waveforms.

• Calculation chart environment using collector, for an average

  Hello

  I was looking for a way to use a waveform graph, added the ability to set the width of the display of axis are all allowing a development of the chart track data, a little.  It is because the self-centering of the graph feature is choppy and does not allow users to zoom in or zoom out on the ground (which my colleagues have asked).

  It's basically my current solution posted here because I think that I finally got a right, but also because I know that you guys tell me: ten ways to do it better.  :%^)

  Note that the data here are slow; I think it would be really embarrassing if we looked at quickly changing data, although you could probably "Collect" more data and on average it all in the same way, to set the center of the axis y of the graph.

  

  The front panel; I put in place the three graphs in a tab control.  (Of course, there are no signals on the data acquisition module, when I did; but at least zero focuses on auto, and the range control works).

  

  I guess I'm especially looking for your comments and I was wondering if I missed an obvious way to simplify this process.

  Thank you

  Danielle

  Hey Danielle,

  Given that it is a long-term test, are you interested displays all the data of your test or only the most recent game? The waveform table allows to memorize and display historical information because it has a buffer associated with it. From your code, it seems that this collector is just used to store information so that you can average the last few data points. The only thing I see standing in your way of simply with an average of your data is that it seems that you display two signals on the graph. So which signal you want to be centered? If you have a signal you want to reach on average to get the center of your chart, you may son of this signal in a convert from Dynamic Data VI express. When you put everything first down, a configuration window appears. You can then select ' 1 D array of scalars"as the type to convert. The output of this VI will then be an array of data points. You can then use the VI means to find the way to this table 1 d.

• Calculating the values of resource (CPU = zero etc..)

  Hello!

  I ' using Chargeback 2.0.1 but I cannot measure the value of average CPU consumption. It doesn't give me 0 Ghz to each customer.

  (The County of vCPUs is fine).

  Best regards!

  You can use its use with ovDCs by distribution.

  Ensure that billing policy that uses the cost model is specified as 'use' of the CPU. Also make sure you have a rate specified for the CPU resource for the period under review.

  Finally, for the test, you must do the TIME use some cycles CPU (use cpuhog or something like that) and make the short period, and/or the price artificially high so that the cost and usage do not round to 0.

  If you do all this, you should see its use not null and a cost for the vApps used enough cycles CPU.

  See you soon,.

  Milos

• Need help with Javascript calculation hidden values.

  See the problem down below. Thank you.

  

  This line is incorrect:

  (TotalValB - CostBasB) = this.getField("NV_B").value;

  Replace with:

  this.getField("NV_B").value = (TotalValB - CostBasB);

• calculation of values in sqlloader before loading the data.

  Is it possible in the control sqlloader file to calculate the values in a particular field and then transfer the data to a table.
  
  for example. If I have a, b, c, d, e, f in csv files.
  
  e field value is based on if a is null or = 0 then b, if c is null or = 0 then d
  and finally e = b | » -'c

  Yes. You can use the SQL functions in your control as a GARNISH file in the example below. You could solve your problem by using NVL I think...

  LOAD DATA
  
  INFILE 'city.txt'
  APPEND
  INTO TABLE CITYOR_TOWN
  
  (
   COTN_NAM             POSITION(7:34) "TRIM(:COTN_NAM)",
   COTN_CITYCODE      POSITION(1:6),
   COTN_ID                SEQUENCE (COUNT,1),
   COTN_STT           POSITION(35:36),
   COTN_CNTY          POSITION(37:39),
  ...
   FROM_DATE POSITION(84:91) DATE "YYYYMMDD" "replace(:MED_FROM_DATE,'00000000',null)",
   H_AVGESTAY           POSITION(19:21) ":H_AVGESTAY/10",
   CLTYPE      CONSTANT "RXTZASCode",
  ...
  )
  

  Published by: Zoltan Kecskemethy on May 27, 2013 17:24

• Calculating the values of dynamic dropdowns

  Hi all, there is the question of the day noob

  I created an invoice form in LiveCycle Designer and I'm totally stuck to the calculation of taxes:

  for each product, you are able to choose between two percentages of tax in a drop-down list, and at the end of the form, I want to show a total amount of each tax.

  unit price net price

  product	Qty		VAT
  Pack of red shoes	2	$ 20	4%	$ 40
  Pack black shoes	1	$ 25	4%	$ 25
  white umbrella	1	$ 10	7%	$ 10

  Total price Excl. VAT	$ 75
  + 4% TAX	$ 2.60
  + 7% TAX	$ 0.70
  Total	$ 78,30

  How can I set the HT 4% and + 7% TAX field to enter their respective product lines?

  Sorry for my bad English... I hope you get the issue!

  If you send your form to [email protected] I codera it for give you to you the idea of how to do it. Please include a description of what you want to do in the email.

  Paul

• Calculator chart 50g. How can I find my firmware version? Thank you, johnnaben

  How can I find my firmware version?

  Thank you

  johnnaben

  I thank very much - the two methods have worked

  johnnaben

• Change a chart value using the date picker

  Hello
  
  I use this code for graphical access
  
  Select deptnm in the Department, eqpnm as MachineN, Sum (Qty) as the amount of work
  where wrkrsltday like to_char (to_date(:P1_DATE), ' MM/DD/YYYY') and item_cd! = '9999' and slipnm! = "PayO" group of eqpnm, deptnm, eqpnm order of deptnm
  
  He works in the SQL command line.
  
  Here I give you the date in the format defined by the user to input.
  But after her run at race time on the date picker, I m selectind all daye is
  the message of no data found
  Guide me on...

  Hello

  I solved the problem; you need to enter P1_DATE in the field "Page to go". I just tested with a few dates - 09/11/2012, 09/12/2012 (I watched your work table to identify the validity dates) and it works fine.

  I changed the password of your workspace to test123.

  Thank you
  Rohit

• Get the field to remain Virgin until the user enters the value in the previous field used in the calculation

  I work on a PDF form and am stuck on one of my calculations. There are two fields 'desired Start Date", which is a date entered by the user. The "desired end" date is one year from date entered by the user. I figured out - however, before the user enters a date, I want this field remains empty. Currently, it fills with 01/00/000. How can I get this field to calculate not unless a date is entered by the user? So far, I tried this but can not get the blank to stay:

  If the field 'Desired Start Date' is empty, leave 'to' field blank

  var myStartDate = new Date (this.getField("Desired_Effective_Date").value);

  If (((myStartDate == 0) & & (getField("myStartDate").valueAsString = "")) {event.value = "";})

  If the field "Desired Start Date" is an effective date, use the date to calculate one year after the date of entry.

  }

  else {this.getField("to").value = util.printd ("mm/dd/yyyy", new Date (myStartDate.getFullYear () + 1, myStartDate.getMonth (), myStartDate.getDate ()))}

  Try the following than the calculation script custom field "to".

  Get the value of the date field beginning

  var sStartDate = getField("Desired_Effective_Date").valueAsString;

  If the start date field is not empty...

  If {(sStartDate)

  Converts a date in a date object string

  Kai = util.scand ("mm/dd/yyyy", sStartDate);

  Add a year

  oDate.setFullYear (oDate.getFullYear () + 1);

  Set this field to the calculated date value

  Event.Value = util.printd ("mm/dd/yyyy", anyway);

  } else {}

  This field blank because the input field is empty

  Event.Value = "";

  }

  You may need to change the date format "mm/dd/yyyy", I used to match the formats of date fields.