Cams has supported to post real-time monitors?

Similar Questions

• SSM-10 real-time monitoring

  Is there a way to receive notifications on ssm module security events in real time, I installed in my ASA? Are some that traps SNMP the only option? Sensor health section has also on the prevention page home/Intrustion ASDM, recovery of events marked as critical "not consulted. How can I erase this? I view the events of the module, and this does not erase it. Does have to do with the product MARCH?

  You can use IME to monitor IP addresses in real-time. It also supports the management of events in real-time for IPS five devices. Have a look:

  http://www.Cisco.com/en/us/products/ps9610/index.html

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps5729/ps5715/ps9610/data_sheet_c78-459033.html

  It is freely available to all customers have a valid service contract. Make sure you that you run 6.1.x code to use the IME performance management features.

  Concerning

  Farrukh

• Is the reference monitor in real time?

  I never asked this before, but is the reference in real-time monitor?

  The behavior I get is...

  frames to update when I rub

  shows the color changes

  freezes when I plate the SEQ

  He always did, but I was wondering what he could play simultaneously with the following. Its video composite value now.

  Unfortunately, you can't direct the program playback and screens of reference at the same time.  It's a design flaw, in my opinion, which greatly limits the usefulness of the reference monitor.  Please tell Adobe you want to correct.

  https://www.Adobe.com/cfusion/mmForm/index.cfm?name=wishform

• The PSC-2000 is programmable with LabVIEW 2010 SP1 / Real Time 10.0.1?

  I have a PSC-2000 camera I want to use for a small project.  I see on the site OR that it is said»

• "Support for LabVIEW Real-time 8.5.1 and earlier" and "Support for Windows Vista and earlier versions.  It means that I can not use the latest version of LabVIEW (2010 SP1) with time real (version 10.0.1) running on a Windows 7 computer?  If not, what version of LabVIEW, real-time and operating system do I need?

When I tried to add a new target under LabVIEW 2010 SP1, the PSC-2000 was not among the choices.

As the support NOR documents indicate, you need LV version 8.5.1 or earlier to program the cFP-20xx devices family.  Version 8.5.1 of LabVIEW does not work under Win7.  You will need Windows Vista or something earlier like XP.

• Toolkit of Real Time Execution Trace functional limitation on targets NI Linux real time taken in charge

  We want to start by using the Toolbox in real-time to backtrace of memory allocation profile on a target of cRIO 9035 & 9039.

  The product information (http://sine.ni.com/nips/cds/view/p/lang/nl/nid/209041) page has a note indicating that the Toolbox has limited functionality on real-time OR-Linux supported targets.

  However, I couldn't find any specific details about what are these limitations.

  If anyone can clarify which restrictions apply?

  Are there alternatives (party packages) that offer a feature more complete?

  Hello Jörn,

  Did some more research, the following limitationrs occur on targets LInux RTOS,

  -The Manager of memory when used on targets of Linux, saves only data for LabVIEW processes and threads, not the global memory of the systems.
  -Wait object are not recorded events
  -Trace buffer size cannot be changed
  -Timed loop pre-emption and reactivation of SRI events are not marked

  Hope that this information helps out you in addition,

  Kind regards

  -Natalia

  Technical sales engineer

• Look at a FPS in real time of the events of several IPS devices

  What is the best strategy for the display of the IPS in real-time of the events of several IPS devices now that VMS filed end of LIFE?

  There was a nice view unique of all IPS events from all IPS devices run in VMS and I was wondering where I can tell people to receive the same information on their networks. I do not see in CSM and I do not think that they will find in MARCH. Please notify and correct me if I'm wrong. Thank you!

  You can use VEI. It is an observer of events that has a dashboard in real time also. You can import several sensors inside and view the events in real time.

  Link to VEI to 5.x versions:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/IPS-EV

  Link to VEI to versions 4.x:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/IDs-EV

  Kind regards

  Maryse.

• My daughter has an air of ipad and iphone 6 mounted on a tripod. She would like to use his phone to photograph/video while you watch on his ipad (in real time)... is it possible? If so, what adapter or cable is needed?

  My daughter has an air of ipad and iphone 6 mounted on a tripod. She would like to use his phone to photograph/video while you watch on his ipad (in real time)... is it possible? If so, what adapters or cables are needed?

  Hello!

  Unfortunately, this feature is only available with the GoPro cameras.

  And Yes, if all cables already existing for these purposes, it would be kind of a pain to take pictures and do not shake the camera accidentally. Maybe, VSCO camera makers will make such feature in some time in the future. This idea is excellent and innovative. Maybe even Apple will listen to users and make their new iOS 10.

• monitor thread on the system in real time

  I have a SMU-8101 controller in my PXI system. I have it running with a system of operating in real time. I inherited some software WHICH has been used on a program of LabWindows used on a PC with a Windows 7 operating system. The SOFTWARE seems to work OK. My problem is when I leave the program I get an ERROR of EXECUTION NOT DEADLY

  "

  Source position thread ID unknown 0x000000EC

  Your CVI program ended on the target in real time. However, there still on the target in real time, the threads that are running or have already run the CVI code.

  Please check that your application cleans all its threads. Son left running after that your application can crash the target in real time when your application is unloaded.

  "

  As I said I got the code and there is a lot of it. I am looking for a smart way to track down these threads. I was wondering if there are tools available that could help with this? Or any other suggestions on how to run these lines down?

  Hi DPearce,

  This article knowledge base has some information on why CmtDiscardThreadPool causes your program hang and gives some recommendations for fixing it.

• I installed camera raw which supports photoshop cs5 several times, but why I'm not able to find the raw camera filter menu Filter?

  I installed camera raw which supports photoshop cs5 several times, but why I'm not able to find the raw camera filter menu Filter

  Hi sharathm,

  Greetings!

  Camera filter gross was not with photoshop CS5.

  You have installed the camera raw plugin and not filter raw from the camera.

  You can open files in camera raw using of bridge or just right click on the image and choose open in camera raw.

  Check out this video here: https://www.youtube.com/watch?v=UKJuUC9_XUg

  Concerning

  Jitendra

• SQLFire has all the apps in real time

  Hello

  Have we not all applications of production or test using SQLFire as a database in real time. If so, vmware has no result, statistics to share in this forum.

  I know it's very beginning as SQLFire himself is in beta version and I believe that as a forward-looking strategy go, SQLFire was set up in any application outside JPetstore.

  Malin

  We were in the middle of finalizing a release and could not answer.

  From the alpha version, there is at least an application running in production.

  There are several ongoing and successful individual oxygen with strict SLA hubs.

  If you have any specific use case we can help you decide how SQLFire fits in these conditions and if meet all expectations.

  Perly, you want to add information?

• LabView real-time and PCIe-8255R w / Marlin camera

  
  

  Hi Bruins,

  You must install IMAQdx on your target in real time. Here is a link on how to do it.

• Photoshop has a brush mirror in real time?

  He how to set a brush so that it acts like a mirror?

  If I painted on one side, the other side is painted automatically.

  

  I don't know of anyway to do it in real time, but it is easy to copy layers and free transform.  This could make an Action to get there with the keyboard shortcut.

  There are also plugins Kaleidoscope and actions out there that would make it easy.  The plugin does not work with CC 2014

  Kaleidoscope 2.1 Plugin - Mehdi - Plugins Photoshop

• LabVIEW 2014 SP1, hardware and real-time PXI

  I'm doing my third LabVIEW Wipe/reinstall in as many days, completely frustrated (and after several calls an hour with the support of NEITHER).  Here's the situation:

  I wrote a fairly large (1000 VI) project of Acquisition/control of our graduate students data used for behavioral experiment on sound localization.  It was developed in 2012 LabVIEW with the module running on a PC/PXI system real time.  It worked very well and was brought successfully under LabVIEW 2014 (with upgrades comparable to the software of the PXI.

  About 18 months ago the students began to write their theses, and at one point stopped gathering data.  Also, at some point, I upgraded the software on this system to LabVIEW 2014 SP1, but I am not sure that I never tested my software with this new system.

  This week, I pulled up the system to use MAX to open some test on the PXI multifunction and DIO card panels to control manually one of the stimuli.  I discovered that MAX could not communicate with the advice on the PXI system - he attributes them as devices VISA, indicating each Board with an icon with a red X means that he could not communicate with the IP that I had assigned to PXI.  Yet, MAX (a) could "discover" this PXI, (b) MAX can 'see' its IP address, and (c) Windows could not only Ping the IP, but could FTP on the drive of the PXI and I could move files back and forth.

  I did two sequences complete "Wipe/reinstall" using LabVIEW 2014 SP1, all giving the same result.  I know it has worked in the past, including when I installed LabVIEW 2014 (without SP1), something I repeat myself now with my third installation.  I discussed with OR (thin?) possibility that there is a "hidden defect" in the Distribution of the SP1, one that is visible to LabVIEW RT users using PXI hardware and go unnoticed because (a) install a few sites of LabVIEW versions SP1, (b) a minority use the RT Modules and (c) PXI is "old material".

  If anyone has such a system or saw a similar problem, please answer.  I'll do a follow-up post if I managed to 'fix' my system by this last reinstallation "a solution of worked before."

  Bob Schor

  Well, the answer is that, in my system, LabVIEW 2014 SP1 with LabVIEW Real-time connected to a PXI system does not appear to connect to boards plugged into the chassis.  Returning to LabVIEW 2014 (fall release), installed in exactly in the same way that the three failed attempts of LabVIEW 2014 SP1, works immediately.  Engineers OR will try to duplicate/verify/possibly patch? in this issue.

  Bob Schor

• Abnormal behavior observed in real-time executable.

  Hello

  I have an interesting problem. I have developed an embedded application of Real-time/FPGA for cRIO 9024 and come across a problem that I don't understand. I work FPGA and RT of top-level and subVIs, proven individually and together when it is run interactively. When I create and deploy an executable in real-time like start, however, the behavior changes. I posted the code below, which I'll explain briefly:

  I have a state machine with 5 States architecture. "Initialize" and "Shut Down" are exactly meet once whenever the device is reset, and the cycle between them is wait > pre-test > wait > run the Test and repeat as many times as desired. Measures are taken by FPGA and past in real-time by DMA FIFO and are then recorded to the TDMS file by the real time. Everything else is just interface.

  The problem comes from the first time, the program enters the Test case to run. The FPGA send measurements as usual, and they are stored in a growing table updated buffering in the fixed-point shift register shown below.

  

  Run interactively, this method successfully bed, buffers, sorts and writes all data in the file. However, in time real executable, only the data collected in the first round (147 items total, as it is initialized by the whole shift register) are saved, the rest seems remainsin a buffer? before calling the following function TDMS write, is that in the case before the next test.

  I'm unable to debug the executable file in real time, probably because of the FPGA reference or some other schema components. I tried to replace the pad with a FIFO in real-time, a variable shared with RT FIFO active and tried to write inside the loop. The FIFO are not improving the situation, and when writing inside the loop, the loop does not run quite fast to stand.

  The problem does not exist when I run the VI interactively from my computer, only when I try to deploy all of the embedded, any application that works (as far as I know) except this one place.

  Any ideas to solve, or workarounds?

  Ryan

  Technical support helped me to resolve the problem, the early termination of loop caused loop condition, although I still don't understand why the behavior was different as an executable file, because the condition of the loop has worked in interactive mode, so if someone has any ideas as to the why, I would still like to know.

• Is there a way to know what physical events are happening in real time?

  I just had a problem from my phone since last week. I wouldn't do something unusual. Knows running programs with regard to my knowledge and visible only windows are concerned. And my hard drive would be thrown open. I don't know which program is the cause. So I asked for help in the windows event viewer and look under hardware events because that's what I thought would contain the event in question. but it was empty.

  I'm here to ask you all, if anyone can help in this regard.

  Amit

  Hello

  Check these:

  Scenarios selected for monitoring performance with Windows Vista
  http://TechNet.Microsoft.com/en-us/library/cc748962 (WS.10) .aspx

  This free utility makes it easy to check the event logs - since you can check everything
  entry in the final minutes or other periods of time. Any or all of the event logs can be saved
  then deleted to make it easier also for future entries to read.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  z http://www.Nirsoft.net/utils/my_event_viewer.html

  =======================================================
  
  Sysinternals has utilties that can help such as Process Explorer, Process Monitor and others. Those
  and others are below.

  This is a pretty complete performance convenience store and a lot of these methods will contribute to
  your effort.

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.