Cannot access files on disk hard when it is used as external drive (sata)

Similar Questions

• Cannot access files on hard disk on windows xp, after I worked with it on win 7.

  Cannot access files on external hard drive on windows xp, after that I worked with him on Victory 7.I can see the file, but he says "is not accessible. access is denied. " Can someone help me?

  As you can guess, this is a permissions problem.  Here, it makes a difference if you have XP Home or Pro you have to safe boot mode to change permissions in the House.

  My crystal ball says that your external drive is formatted with the NTFS file system.  When you connected to Windows 7 (or any other computer besides), the files have been added that this user permissions apparently understood that only Win 7 has access to.  There are several ways to handle this...

  Is to save on all your files and reformat the external hard drive with a FAT32 file system and then support files.  You will have no problems of permissions with FAT32, but you can't have any higher than 4 GB single file either.

  Another way is as an administrator, to 'Ownership' of all the files on the disk
  "How appropriate a file or a folder in Windows XP"
     <>http://support.Microsoft.com/kb/308421 >
  but this could get old if the drive moves back.

  Yet another approach is to give "Everyone" full access to everything on the drive.  This may or may not protect against new folders or files added, but may be worth a try:
  As a user administrator, open a command window:
  Start-> Run-> "cmd".
  Then, enter the command:
  CACLS E:\/t/e/c/g everyone: F
  (where I am assuming that your external drive is mounted as "E:" - change of real player)

  I hope that something more top is useful...
  JW

• Cannot access files between local network PC

  I have 2 computers ethernet under XP Home SP3.  They are of type ethernet connected behind a router wireless Airllink 101 a Vista laptop is connected on the wireless (the Vista laptop cannot access files either).  At the same time as I had a third ethernet PC connected without SP and I was able to access his files for at least one of the other PCs.  I tired remove firewalls (temp) and Virus check without success.  In the network section, I can see the computers and shared files on the PC but when I try to open directories is said I can't have permission to use this network resource.  Memory: server to process this command.  Server?  Here is the esentiallly peer computers back-to-back.  I have 50 + GB on each PC.  I believe that this has happened after that I installed SP2 or SP3.

  See the article in the Knowledge Base Microsoft Antivirus software may Cause Event ID 2011 for a likely solution.

• I cannot access the application "contact me" when a website, get error "Default Mail Client not properly installed."

  I cannot access the application 'contact me' when a web site and receive the answer "Default Mail Client not properly installed" instead of going on the requested site.

  How can I fix this problem?

  Separated from the:

  http://answers.Microsoft.com/en-us/IE/Forum/IE8-windows_other/IE8-default-mail-client-not-properly-installed/23c2a9e1-d1fa-4a50-aeb1-90a6f2af717f

  CrystalBall © SEZ...

  Unlike Windows XP & Vista, Windows 7 does not include a default email Client. [What were thinking?]

  You will need to install a (e.g. MS Outlook;) Windows Live Mail; Thunderbird) , and then set it as a default for mail in CUSTOM (<>) article in Set Program Access and defaults of the computer , then restart your computer before any function send to or MailTo will become available.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In these forums, you will find support for Windows Live Mail: http://windowslivehelp.com/forums.aspx?productid=15

• Windows cannot access file you will not have permission to access the item path or specified device.

  Windows cannot access file you will not have permission to access the item path or specified device.

  I have windows7 OS, I try to open any application above the display of error messages.

  Please help me...

  Thank you!!!

  original title: Windows cannot access

  another user account works fine.

  Then, your profile is corrupt.  Create a new user, copy documents and other profile corrupted on the new profile.

  Do not copy * all *-only things you have created.  (Except the shortcuts).

  Is the user profile damaged an administrator or standard user?

• Best practices MMO. Download music and heavy files on disk hard users?

  Best practices MMO. Download music and heavy files on disk hard users?

  I just downloaded a Hello Kitty MMO application to search (for my kids of course).

  I am developing my application of teaching of English with LOADS of classical music, mp3 and heavy bottom BGS phrases. The best idea would be client to download them to their drive hard is to say that I wouldn't need their flow and therefore save a fresh wealth of bandwidth from my ISP?

  See you soon

  You will need test and see what works best for you... as I said, the files are cached and used in the cache whenever possible. However, there is a limit to the size of the cache, and if your files are huge then yes there is probably more sense to download. Or get a better reception where bandwidth is not a problem...

• Why raw of Sony DSC-RX100M3 air files strange in PE9 when flash was used in the shot?

  I just bought a camera Sony DSC-RX100M3 and use in RAW + jpeg.  I want to use in my Photoshop Elements 9 raw files, having the Camera Raw plugin version 6.5.0.216 installed. I downloaded the Adobe's DNG Converter 8.7.1.311 version so I can import my Sony raw files into EP 9 because they cannot be used directly. Most of the time these files raw look OK, but when I use the flash on my camera and then look at the raw files in PE9 they seem much more pink than jpeg files. Jpeg files are more or less similar that I remember the scene when I took the picture.

  When I look at the same raw and jpeg in Sony files have (version 4.2.04.17270) software Image Data Converter the raw and jpeg files are similar to one another and there is no colour pink cast in the raw file.

  What I am doing wrong in Photoshop Elements? I have the DNG Converter retains all the information from the original raw file and makes no changes, so why not the raw file look so different when flash was used?

  Thanks for any help you can give!

  AVM

  I interpret the differences that you see the difference between the Adobe Standard camera profile and that Sony made with the colors.

  I can get things to look more like what you see in-camera jpg by simply changing the Adobe Standard camera to camera neutral profile on the camera Calibration tab.  I don't remember if PSE9/ACR6 has these available camera simulation profiles or if you has that Adobe Standard.  If you have the other, then switch to the use of one of them.

  Here's what the image looks like in the last Camera Raw plugin 8.7.1 to PSE13 after having chosen the camera neutral profile that looks less magenta and more green as the JPG:

  

  I think that part of your question is that you have mixed lighting where the light blue flash is mixing with some slightly more hot (incandescent) or (fluorescent) green color to the right side is hotter than the left side.  Apart from the differences in color, there is also a shadow in the foreground, perhaps caused by your sun visor that should be eliminated or your goal is too long to use a flash that relatives or something.

• Cannot access files/folders in external hard drive after installing Windows 7

  Original title: device Seagate Ext Drive

  I have insalloed windows 7 and can, t get disc to open my files of suggestions please. Windows 7 did not installed new

  pilot. icon just no way to access my saved files.

  What about Clyde UK

  Hi Clyde,

  1. do you get an error message/code?

  2. What is the model number of the external drive?

  3. What is the brand and model of the computer?

  In order to diagnose the problem, you can check if Device Manager disk external drive is listed:

  a. type devmgmt.msc in the start menu, run the box, then press enter on the keyboard.

  b. in Device Manager, check if the hard drive is listed in the list of devices.

  Method 1:

  I suggest you to connect the hard drive to a different USB port or connect the external hard drive to another computer and check if the problem persists.

  Method 2:

  Check out the link and follow the steps in the article:

  What to do when a device is not installed correctly

  http://Windows.Microsoft.com/en-in/Windows7/what-to-do-when-a-device-isn ' t-installed-correctly

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• Cannot access files on external hard drive connected to Windows XP to Windows 7

  Original title: to access the shared files on an external drive using Win7

  I have created a shared folder on an external drive attached to my WinXP Home addition.  When I try to accIess to the shared folder on Win7 I see the folder but cannot access the files.  Yet when I create a shared folder on my XP I correctly read files.  Why can't access the shared folder on my external hard drive on my network

  Hello

  Do you get any error messages?

  Method 1:

  I suggest you to go through the steps mentioned in the link and the Coachman.

  Error message when you try to access a network Windows XP computer: "you might not have permission to use this network resource".

  http://support.Microsoft.com/kb/913628

  To do: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756/

  How to back up and restore the registry in Windows

  Method 2:

  I also suggest you go through the steps mentioned in the link and the Coachman.

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  In addition, we can see:

  Windows 7 & HomeGroup: share with other Windows XP and Windows Vista operating systems

  
  

  http://www.Microsoft.com/download/en/details.aspx?ID=17168

  Hope this helps and keep us informed if you need help.

• Cannot access files locked with access TrueSuite Manager

  I have files with Access Manager TrueSuite locked. My Windows bug and now I cannot access these files locked.
  When you try to unlock, I get the error and I can not read these documents.

  Thank you.
  Excuse my bad English.

  I found this document:

  Useful information about the file protection with AuthenTec fingerprint software
  http://APS2.toshiba-tro.de/KB0/TSB9C02RC0001R01.htm

  Eventually, you will not be able to unprotect the files again
  But try this backup data to the external HARD drive or somewhere else.
  Then reinstall this software and import data from external source.
  Then try to unlock this new

• External HDD PX1277E - 1 08: cannot access files after HDD felt down

  Hi all
  my beautiful felt down external HARD drive. The first part of the disk has been partitioned as free and contains the software that is used to unlock the secure parttition.
  After the success on the field, there are error messages if plugged into usb. Some dll´s are not readable etc, seems that some parts are not readable.

  How can I access the large and assured the part of my hard drive, y at - it software? I know that my pw, but the software does not point to pose for him.
  Thank you very much...
  Eric

  Very bad looks like Buddy :(
  If the HARD drive cannot be recognized then disk failure HARD and eventually, he died.

  Of course, there are a lot of special companies that could save the data of the failed HARD disk, but even I know this is not easy and costs a small fortune

• a folder containing 102 GB of files on disk hard ext appears as empty in windows Explorer

  I have a folder on my external hard drive (western digital) that according to folder properties shows like containing 102 GB of data, but when I try to open the folder in Explorer windows (or any other program) it is said that the folder is empty - what possible reason would be for this?  all other files on the same hard drive display in Solution Explorer and opens properly.

  any help with this would be greatly appreciated.
  Thank you
  I just checked the properties of the folder and the hidden box is not checked, and permissions are for everyone - any other ideas?

  Hello lizziepool,

  Thanks for the return of the response.  If you connect your external drive to a different computer you duplicate the same question?  I've included below are two links that I hope will help you to be able to view your data.  Please let us know status.

  Microsoft Answers:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-files/folderfile-transfer-to-an-external-hard-drive/9c60f7d6-bd9b-4771-BB46-f8b3d57466d1

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-files/trouble-accessing-folder-on-external-hard-drive/b1c7525a-fe34-42f9-A1C9-1b1c7b079be3

  Thank you

• cannot read files on disk or source file

  Old computer crashed and had to buy a new one. All files from the old pc photo copied from a cd/rw for transfer to the new pc. The new cd/rw pc drive will read and copy only half of the files on the disk, but the other half continue to flow upward "cannot read from source file or disk. The op Player stops and is more bed drive when I get to these files. Suggestions are greatly appreciated. Thank you.

  Hi modelkit,.

  Welcome to the Microsoft Answers site.

  It seems that the problem is related to your support. To check if the media is corrupted or not, you can follow one of the following methods:

  Method 1: Try to copy the files to another computer.

  If you are not able to copy the files in another computer, then we certainly know that the CD has bad sectors which prevent copy of file.

  Method 2: Run Xcopy to check if the disc is damaged or not:
  
  1. click on start, principally made programs, click Accessories and then right-click on command prompt, click run as administrator.

  2. type the following command line and press ENTER. In the command line, drive is the letter of the CD drive or DVD drive.
  xcopy drive:-*. * /s > c:\test1
  If the XCopy process is not successful, the CD is damaged. Therefore, the CD or DVD drive cannot read it.

  The corrupt media, you can try manually copy each file. This will ensure that most of the files is copied leaving only the files in the area of corruption.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• Importation and LABELLING of the AVCHD files on disk hard ext to the Prime Minister

  3 questions (I'm on an iMac)

  (1) I brought the AVCHD (entire file) files from an SD (Sony PXW-70) to an external hard drive.

  Hard disk, it is not possible to see individual clips to open the file "AVCHD".

  When I click on it, I see the individual clips. I can not re - appoint these clips. They are

  Clip #1 Clip #2 etc how ca label clips while remaining hard disk, before to do first?

  (2) I imported the files in the folder of the hard driveI first and then named the clips (with numbers).

  When I open the project a) it says media is offline. so I have to manually link the media b) media other shoots

  that have the same number or clip 00002 become confused and shows it to the top. Help!

  I spent an hour and a half with the Prime Minister on the phone including coming on my desk and then they told me I should

  chat with SONY (camera) and see what Extractor they recommend.

  THANK YOU FOR YOUR TIME

  Consuelo

  https://www.bhphotovideo.com/c/product/1072752-reg/sony_pxw_x70_professional_xdcam_compact .html

  Do not rename the files as a logging.

  Copy them to folders separated from each card so that the file numbers are not incompatible. for example "rushes" map 1 "rushes" card 2 etc...

  Ingest them in tubs of project same distinct file naming protocol.

  Save the files using the Description field

• Cannot access files recovery

  I had to do a recovery my PC system and before, then used the program of recovery to automatic backup on my external HARD drive.

  I have since then found my backup there and it extracted in a "System recovery files" folder on my pc. But it won't let me access it, so I can't copy their back or open up.

  Whenever I try to open the file it says I do not have the necessary permissions to access the folder and directs me to the folder security options. Even if I am logged in as an administrator, I can't give all the permissions to view or edit the file.

  If it's supposed to happen? How to access my files?

  Take a look at this thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-security/access-denied-to-2nd-hard-drive-in-win-7/35013321-4244-4095-a295-c778bc2f22a3

  Scroll until you see the answer and then find the paragrahp "to take ownership of a file, follow these steps:"with instrcutions step by step on the way. "