Similar Questions

• Cannot access some sites behind the pix515e

  I started my CISCO PIX 515e in July 2004 with a minimum configuration. The only change I made was to introduce the syslog and 3COM tftp server. Two weeks after my Internet (browsers) users (inside) began to have problems of access to certain sites for example google.com, cnn.com etc when I bypass the firewall, they can access all the sites. When I place them behind the firewall again they cannot access the same places. It seems to me that the firewall is the cause. This could be the cause?

  Without seeing your config, it is hard to say, but a proposal, I'd say you're probably out of translation addresses. The PIX must create a translation for the traffic as it comes out, and she does that based on nat/global orders, you have in there. Let's say you have the following:

  Global 1 200.1.1.1 - 200.1.1.254 (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Then, this indicates the PIX to translate any internal address to 200.1.1.x he died. If all of these 254 global addresses be used however the next person who tries to go out will be denied. If you look at your syslog server, you will see a message like "Unable to create translation."

  If you change it above to:

  Global 1 200.1.1.1 - 200.1.1.253 (outside)

  Global 1 200.1.1.254 (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  then the first 253 users that come out will have their packages would NAT, then all of the other packages will be PAT had to the 200.1.1.254 address, giving you an extra 65, 000 - odd outbound connections.

  If that's not enough (remember that only the user going to a few web sites can open connections to 20-30), then you can change the above to the following:

  Global 1 200.1.1.1 - 200.1.1.252 (outside)

  Global 1 200.1.1.253 (outside)

  Global 1 200.1.1.254 (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  giving you a 65, 000 - odd additional translations and so on.

  Other than that, we would need to see your Setup and your messages to syslog (in the debug level) when these users can't get out.

• Googlebot cannot access your site. Has anyone encountered this problem before?

  Hello

  I'm a rookie at this. I just wanted to create a simple site and could use the tools webmasters google crawl my site

  but it happens

  "I received an e-mail from saying: webmaster tools".

  Googlebot cannot access your site.

  Recommended action

  If the site's error rate is 100%:

  • Using a web browser, try to accesshttp://www.graphicsigns.co.nz/robots.txt. If you are able to access it from your browser, your site can be configured to deny access by googlebot. Check your firewall configuration and the site to ensure that you are not denying access by googlebot.
  • If your robots.txt file is a static page, check that your web service has appropriate permissions to access the file.
  • If your robots.txt file is generated dynamically, verify that scripts that generate the robots.txt file are properly configured and have to run. Check the logs of your Web site to see if your scripts fail and if so try to diagnose the cause of the failure.

  If the site's error rate is less than 100%:

  • Using webmaster tools, find a day with a high error rate and review logs of your web server to this day here. Look for errors to access robots.txt file in the logs for that day and fix the causes of these errors.
  • The more likely explanation is that your site is too large. Contact your hosting provider and discuss to reconfigure your web server or by adding more resources to your Web site.
  • If your site redirects to a different host name, another possible explanation is that a URL on your site redirects to a hostname portion of his robots.txt file exposes one or more of these questions.

  Please need your help & expertise to solve this.

  Musch appreciated.

  Hello

  Sitemap.XML is automatically created and updated in Muse. If you are hosting the Business Catalyst, then the sitemap.xml is not created by Muse. It is created by a process that runs periodically on the servers of BC, so it can take up to a day before the sitemap.xml in British Colombia has been updated.

• Win 7 64 bit: cannot access Web sites randomly

  I had this problem for a long time, with several computers and various installations of windows.

  After my computer has been for a few days, I'll suddenly find me unable to access all the web pages. Programs like MIRC, Skype and steam work perfectly, like online games. I just get a generic "unable to connect to the server" error when you try to access Web sites and I cannot ping all websites such as google.com (it instantly timeouts).

  Do ipconfig/release, / flushdns and / renew fixes it for a few minutes before I lose the ability to access the Web sites again.

  Disabling/renewal of the NIC does nothing and troubleshooting of windows doesn't find anything wrong.

  The only semi-permanent solution I found is to restart my computer, but the problem will occur again in a few days.

  Servers using openDNS makes no difference. Nor is switching between ethernet cable and wireless. This problem is not dependent on the browser. Reboot the router it corrects only for a few minutes until I became unable to use websites to access again.

  Does anyone know what the cause of the problem and how to fix it permanently?

  Hello.

  I suggest you to configure the TCP/IP settings and check if it works:

  http://support.Microsoft.com/kb/2779064/en-us

  If the problem persists, I suggest you consult the website of the manufacturer of the laptop computer to download and install the latest network driver and check the results.

  Please let us know if the problem still persists.

• Cannot access some websites with any browser

  I can't access some websites with any browser

  What happened with a few sites, but who is really upsetting me is https://simply. freetax.com

  I tried IE, Mozilla and Opera

  In each one I click on the link then it takes forever for what it is loading and when it does it is one of the many messages of error according to the site.

  It is not my ISP or router is blocking the site because I can access it from any of the other 4 computers in this House. It seems that the problem is limited to my desktop unit. I tried to disable my firewall and antivirus. I erased from history. I have no idea where to go next.

  Help, please

  Thank you

  Hello

  Thanks for posting your query in Microsoft Community.

  This problem may occur if there is a change in the configuration and network settings.

  See methods below to solve the problem.

  Method 1

  Try running the Fix - It from the link below. He will try to correct the most common problems with the network.

  https://support.Microsoft.com/en-us/KB/299357?WA=wsignin1.0

  If the problem persists, check the method below.

  Method 2

  Try resetting your Internet Explorer and see the link below. He starts the internet explore to the default state.

  http://Windows.Microsoft.com/en-us/Windows7/reset-Internet-Explorer-settings

  NOTE: The Reset Internet Explorer Settings feature might reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Also re - activate the Add-ons.

  Check if it helps.

  Method 3

  Web connection issues are frequently a corrupt DNS cache. Flushing the cache is an easy solution to many of these problems.

  Here's how to fix this corrupt DNS cache.

  1 click Start.

  2. type cmd in the search bar.

  3. right click on cmd and select run as administrator.

  4. in the command window, type the following, and then press ENTER:

  ipconfig/flushdns

  5. you will see the following confirmation:

  Windows IP Configuration properly empty the Cache of DNS resolution

  For any Windows help in the future, feel free to contact us and we will be happy to help you.

• Cannot access the Sites on US data center?

  I can't access some of my sites on the data center we are other people having this problem?

  I don't see anything on the status page.

  Hi Lynda,

  We experienced some intermittent network problems earlier in the day, which are now resolved. My apologies for the inconvenience and thanks for your understanding.

  See you soon,.

  Jackson.

• Trouble accessing some sites like Yahoo and Facebook.

  Original title: Internet Prolems

  I have internet explore 8 and im having difficulties to access certain sites like yahoo and facebook.  I can not also open google chrome and I don't know why.  Does anyone have idea as to what could be the problem?

  Hi claymzz40,

  Thanks for posting in the Microsoft Communities. The problem description, I understand that you are not able to access the Internet. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         You use a third-party security software?

  ·         The issue is limited to particular Web site?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Step 2: If the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state from the link to start the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  You can read this article for more information:

  Wireless and wired network problems

  Let us know if you need more assistance.

  Thank you.

• AnyConnect client cannot access external sites

  I am installing AnyConnect VPN with no split tunneling. ASA 5505 v8.2. It seems that it should be really easy. I must be missing something.

  I can get AnyConnect users to connect very well and they can access internal sites and on other sites in IPSec tunnel. But no access to internet.

  Internal 10.1.1.x pool VPN is 10.1.1.251 - 253 (list of Temp for the test). I have published the following plotter:

  packet-tracer input outside tcp 10.1.1.253 12345 69.147.125.65 80 detailed
  

  The last reported point (where it fails) is:

  Phase: 7
  Type: WEBVPN-SVC
  Subtype: in
  Result: DROP
  Config:
  Additional Information:
  Forward Flow based lookup yields rule:
  in  id=0xda7e9808, priority=70, domain=svc-ib-tunnel-flow, deny=false
  hits=364, user_data=0xcb000, cs_id=0x0, reverse, flags=0x0, protocol=0
  src ip=TempVPNPool3, mask=255.255.255.255, port=0
  dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
  

  Which means by SVC-WEBVPN?

  A relevant config:

  No ACLs, filters or limitations of policy group on HQ customers.

  Security-same permit intra-interface

  Global 1 interface (outside)

  On advice, I've added: nat (outside) 1 10.1.1.0 255.255.255.0, then I can get no tunnel guests outside guests, but then no IPSec.

  Kind of a weird, that with this, the tracer of package does not change. Continue to deny shows, but the site is accessible.

  When you say tunnel IPsec sites... is that the tunnels IPsec Site to Site on the SAA?

  The command:

  NAT (outside) 1 10.1.1.0 255.255.255.0

  It should allow the AnyConnect customer pool for PATed to Internet.

  If you need clients AnyConnect to access the Internet and the access to remote IPsec tunnels as well, you can do it with policy NAT:

  access-list anyconnect deny ip 10.1.1.0 255.255.255.0 x.x.x.x

  access-list anyconnect deny ip 10.1.1.0 255.255.255.0 y.y.y.y

  access-list allowed anyconnect ip 10.1.1.0 255.255.255.0 any

  NAT (outside) 1 access list anyconnect

  Global 1 interface (outside)

  With the above configuration, you are bypassing NAT for AnyConnect customers when they want to access remote sites through the IPsec tunnels (assuming that x.x.x.x and y.y.y.y for remote networks through these tunnels).

  And the rest of the AnyConnect (10.1.1.0/24) pool will be PATed to Internet.

  Federico.

• [N900 / WNDR4500]-cannot use / access some sites web/services even after reset to factory settings

  Hello

  I just moved into a new home; my old cable modem was damaged during the move, and so I had to replace it (same manufacturer, newer model). The problem started then with messeging (Messenger of the LINE) service not working at all when the wifi - direct connection has worked very well for the PC and the phone worked when using mobile data. Until now, it appeared that this app has been affected that I could still do other things very well (for example surf the web, email checked).

  I tried the firmware update and later reset the router to the factory settings, or even delete the app and reinstalled it, but they've made the app worked part of the time only. However, I noticed recently that I couldn't access certain Web sites via wifi, too. Again, problem has disappeared during the use not wifi.

  No idea on how to solve this problem is highly appreciated.

  Thank you

  b.

  go to settings... internet configuration... Select use PC MAC address... restart the modem and router

• Cannot access internet sites - Satellite A30-92

  I have a laptop Satellite A30 - 92.

  Suddenly I'm unable to access most of the internet sites. Can I use it fine at high speed and on the LAN, but using the dial up, no.
  I can dial my ISP very well, but it will not download web page. Oddly enough I can get some (but very few sites), but above all no that I looked at the Device Manager and the modem works fine. Looking at the ports I have a ltp printer port, but no com port doesn't appear.

  This could be the cause and how to fix? Thank you.
  I must say I checked the firewall and even turned off.

  Must the connection by modem specific DNS and Proxy settings? Call them and find out.

  If you are using IE, try to disable Protected Mode.

  Or maybe just try another browser such as FireFox.

• Cannot access any site to play online games

  Hi to anyone who can help me with this.  I have Windows XP and downloaded IE 8 some time ago.  Never had any problems until about two weeks ago.  Every time I have access to MSN GAMES, GAMES YAHOO, 'what' that is the games and try to play online, my computer completely freezes... I mean completely and it hangs forever.  Not even doing Ctrl + alt + delete to close the program.  I have to manually turn off the computer and boot from fees.  I get no error message, nothing... just a little noise beep (not like a pop-up), then the big freeze.  I tried to play on the web games on my second computer and the same thing is happening EXCEPT, I have now the message on IE shutting and something to do with the DEP (Data Execution Prevention).  I checked the Advanced tab in the system but can not change a thing.  It's so frustrating because it just started to happen.  I even uninstalled and reinstalled IE 8, went through all the procedures I can think and basically nothing changes.  Can someone please help?  Thank you.

  For the purposes of troubleshooting, I suggest to test websites on another browser to see if the problem is directly related to something in Internet Explorer, or elsewhere.

  This gives a test:

  1. go on http://www.mozilla.com/en-US/
  2. click on download, click on "Run" and follow the instructions to install
  3. after installation, restart the system and try to access these Web sites

  * You may need to install Adobe Flash Player plugin, if the content does not load. In most cases, if his need, it prompts.

• Cannot access the site Web Microsoft Updates - error 0X8024402F code (cannot display page)

  original title: the site has encountered a problem and cannot display the page you are trying to view. Error 0X8024402F code I can not download the updates to my computor

  I tried to download the updates on Microsoft Update, but get the error 0X8024402F Code. The website has encountered a problem and cannot display the page you are trying to see!

  0X8024402F

  Treatment of the external WU_E_PT_ECP_SUCCEEDED_WITH_ERRORS file completed with errors.

  It is a Windows Update error, which indicates some sort of connectivity problem.

  See - you may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates

  http://support.Microsoft.com/kb/836941>

  UTC/GMT is 07:19 Monday, January 2, 2012

• Cannot access Web sites after refresh

  I can't download my pictures to the usb and the computer does not allow me to download anything at all

  Original title: I can not download anything windows8 IE 10 I refresh computer and its worse I can't access multiple Web sites

  Hi Maxine,

  According to your description, it seems that you are facing several problems on your computer. I will help you certainly with the same. However, we need a few details to better understand the cause of the problem.

  1. You have recently made any changes on your computer, prior to download?

  2. You get no matter what error message when you access the Web sites?

  3. What is the brand and model of your computer?

  4. Y at - it an update of Windows that recently failed?

     Note: For the numbers of KB updates of windows, the underlying steps:

  1. Press Windows + C to open the bar of charms.

  2. In the search box, type Update, and then in the list of results, click Windows Update.

  3. In the left pane, click view update history.

  From now on, I suggest the following methods:

  Method 1:

  Start the computer in a clean boot State, and check the status. A clean boot to check if any service or third party application startup is causing this issue.

  Clean Boot WARNING: putting your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  Once you perform Clean Boot please perform method 2 to continue troubleshooting.

  Method 2:

  Make sure that all Windows updates are installed on your computer, as the issue may occur because of some missing security updates.

  Please follow the steps to install the available Windows updates.

  1. Press Windows + C, type Windows Update in the search box, and then click Windows Update in the results pane.
  2. Click find updates. When the scan finished, click optional review updates.
  3. Click the check box next to the update, and then click install updates.
  4. If you are prompted, read the license agreement, then click I agree.
  5. Follow the instructions on the screen to download and install updates. If you are prompted, restart your computer.

  Once all updates installed, please restart your computer and check again.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• I couldn't access my site to administer once a domain is expired 2 days ago. Now, I renew and still cannot access the site. How can I fix this quickly?

  I'm running a campaign and need this site www.purpleperfect.com to get a direct return. I couldn't wait until Monday to contact support because of the campaign of marriage. This is the case, my domain namecheap expired 2 days ago without realizing it. I renew my domain name today. still, I can't access my Web site to administer www.purpleperfect.com. He said disabled administration immediately after that the domain is expired. How can I resolve this quickly? I had to stop all campaign and this will certainly affect results. Please help me it is a matter of urgency.

  

  IF your domain name expired has nothing to do with BC. You can't do anything in British Colombia if this is the case. You need to go to your registration office and pay the Bill there.

  If you referring to the OCA itself you can go to the url of development:

  I had to guess; http://purpleperfect.BusinessCatalyst.com/ but this is not the right one, but if you know the url of your development, you can go to this.

  IF you need to pay a bill of BC when that expires when you go to the site and the connection, it will give you the chance to pay for it.

  I remembered that you have purchased an SSL tries to use the before BC:
  I just purchased GeoTrust RapidSSL Certification at Namecheap... help!

  If you need to help the development and construction of your site, it may be worth paying a developer to sort some things for you.

• Latest version of Firefox (version 32) cannot access web sites. Using Windows 8.1 compatibility issues?

  Firefox will automatically update to the latest version which is now the 32 version. I get the following error message: "Firefox can't find the server at us.data.toolbar.yahoo.com"preceded by "Sever not found" what is happening on any site web I'm trying to access. Reload version 31 Firefox works fine, but then it will be updated again.

  Windows 8.1 is my operating system.

  The latest version is 31.0 Firefox as the only way you would be updated to the current Beta build, which is Firefox 32.0b2 (b2 = Beta 2 as you can say six to 12 beta) build is if you were on the beta channel because of you install a beta version and that he continued to use it since. If you have installed the Firefox 31.0 is upgrade to 32.0b2 then the 31.0 you have installed is a Beta version (make sure the name of the file has not had to say 31.0b# because there were nine of betas) and not the Firefox 31.0 release say mozilla.org or https://www.mozilla.org/en-US/firefox/all/

  The typical reason for a new version (Windows) being not not able to connect after a new major version of Firefox update or install is usually due to a software firewall does not block the new .exe but it can stll have the previous version allowed.

  • https://support.Mozilla.org/en-us/KB/Firefox-cant-load-websites-other-browsers-can
  • https://support.Mozilla.org/en-us/KB/configure-firewalls-so-Firefox-can-access-Internet