cannot access the editor control, access denied

Similar Questions

• "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".

  Original title: when setting up Windows Media Center, I get the error message: "IR hardware not detected".

  I have an internal TV Tuner that has been installed by HP, when I bought recently a "computer build-your-own." (According to the control panel Device Manager, my tuner is a Win TV HVR 1290, made by Hauppauge). The computer came with Windows 7. While installing Windows Media Center, after setting up the TV Signal (on channel 3) I am able to see a video thumbnail on my computer screen. I am also able to change the channel using my remote control U-Verse (not the Windows remote control supplied with the computer). So far so good! I then hit next and get the following message: "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".  After you receive this message, the installation procedure is completed. I called HP that support intalled the tuner. They had not the slightest idea what to do. I then called Hauppage customer (manufacturer of TV Tuner). They said that I need to plug one end of the IR Blaster cable that shipped with the computer in a slot in the back of my computer (they told me which slot). They said so to run the IR all the way cable to my cable box and the other end of the cable to my cable box of band. They said it was necessary to be able to use my Microsoft Remote to instruct the box to change channels (cable IR stuck on the box). I told her that I did not use the Microsoft Remote, I could change the channel with my U-verse remote (that I preferred to use anyway). He said that it took the cable on the band decoder in order to remove the error message and the installation of Windows Media Center. I then called U-Verse technical adapter who informed me of their set-top boxes (made by Cisco Systems) do not have the ability to receive signals IR IR Blaster cable (or any othe IR signal source). Microsoft is apparently not understand how U-Verse set-top boxes are designed to work and sells a product incompatible remote control/IR. My question is this: How do I set up Windows Media Center, in order to avoid getting the error message "IR hardware not detected" when you install Windows Media Center and just use the remote control of the U-Verse that I prefer to use in the first place. Once understand you this point, please send the information to HP, At & T U-Verse and others. Thank you.

  Ron, I have something for you!

  and for all the people who have this problem :)

  Hi, I had the time of IR not detected in Windows 7 Ultimate with a TV wonder 650 card and a box of digital adapter from Verizon for my PC... Go on the road to installation and after the Media Center channel search, choose manual configuration. Choose the aerial signal (I aso picked after this analog) l. After he sought more, he finds no channels.  Do not be afraid. Just accept it and go to the main settings page in the Mediacenter. If I remember correctly, then select TV Guide. Choose Add channel. I added the channel 3.

  Since my Verizon box has no IR for the computer, I added the channel 3 for the media Center and I change the channels with my Verizon remote. All my stations in the Verizon box go to Channel 3.

  The story here is so, for some reason any Windows detects that only my box channel signal TV and you must manually configure the media center on the air, then go to settings and add the channel you want in the guide.

  Why the guide TV control which channel you can tune is beyond me, but the scanner locks all channels, it does not detect. they must be added manually in the guide.

  My TV works and looks okay now.

  It actually works!

  the only problem is that it is not in HD

  but there is something

  
  

• Course Photoshop 11. Suddenly cannot open the editor. Get 'Runtime Error' help!

  The race 11 Photoshop very well in recent weeks. Suddenly cannot open the editor. Get 'Runtime error' tried to open the Editor Welcome window and organizing thru, no difference. Organizer works very well. Windows 7, 64 bit. Help please!

  [transferred to Photoshop Forum]

  See if that helps (acting 9.0 to 11.0):

  http://helpx.Adobe.com/Photoshop-elements/KB/Microsoft-c-runtime-error-launcing.html

• Cannot start the grid control

  Hello
  
  I got the grid control Setup on a server laboratory almost a year back and everything worked very well.
  a week back from the developer could not access the URL.
  
  
  While I try to start the services, I get the following error:
  
  xvmdsxaor03: / opt/oem/oms10g/opmn/bin >. / opmnctl startall
  opmnctl: from opmn and managed all process...
  =========================================================================
  opmn id = xvmdsxaor03:6200
  0 out of 1 process started.
  
  IAS instance-id = EnterpriseManager0.xvmdsxaor03
  ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  IAS-component/process-type/process-set:
  HTTP_Server/HTTP_Server/HTTP_Server
  
  Error
  -> Process (pid = 1382)
  Cannot start a process managed after the attempt limit maximum
  Journal:
  / opt/OEM/oms10g/opmn/logs/HTTP_Server ~ 1
  
  xvmdsxaor03: / opt/oem/oms10g/opmn/bin > 10 g/opmn/logs/HTTP_Server ~ 1
  ========================================================================
  
  
  According to the newspapers:
  ========================================================================
  06/09/23 07:59:55 start
  --------
  apachectl does not belong to this user
  ========================================================================
  
  I checked for .apachectl and its property by the same user "oraoem" that I m starting services with. I'm not sure what is causing this problem:
  
  [root@xvmdsxaor03 bin] # ls-l .apache *.
  -rwsr-s - 1 oraoem s/n 1716966 5 August 2005 .apachectl
  [root@xvmdsxaor03 bin] # pwd
  / opt/OEM/oms10g/Apache/Apache/bin
  
  Please notify.
  
  Thank you!

  What are you user to use 'startall opmnctl?

  Ok...

  Please...

  $. / opmnctl stopall

  $ ps - aef | grep oms10g

  And then if find some process... Kill it to superuser.

  # kill-9 ID_processus

  OR (be careful)
  # ps - aef | grep oms10g | AWK '{print $2} ' | XARGS kill-9

  Go to/opt/oem/oms10g/Apache/Apache/logs PATH

  # cd/opt/oem/oms10g/Apache/Apache/logs PATH

  Check the file httpd.pid

  # ls - the httpd.pid

  It must not be permission oracle, don't mind... verification process and remove

  # ps - aef | grep 'cat httpd.pid '.

  If find... kill

  # rm f httpd.pid

  Oh apachectl file (it is owned by oracle)

  -rwx - 1 oracle oinstall 12615 10 May 2007 apachectl

  After that the oracle Goto user, and then use 'startall opmnclt.

  $. / opmnctl startall

  and check the log

  Good luck

• Cannot remove the Catalyst Control Center

  Original title: Catalyst Control Center

  I want to uninstall my CCC, but unfortunately the CCC Install manager has been uninstalled by mistake.

  I can uninstall the CCC with on the Installation Manager, or I can re - install the Manager of the facility on its own to allow me to do the uninstall.

  Hi Nick,

  1. What is the error you received when you try to remove the Catalyst Control Center?

  2. What is the brand and model of the PC?

  Catalyst Control Center is ATI so check with the ATI support, their documentation online
  and drivers and ask in the Forums of ATI for known issues.

  In addition, you can try to reinstall the CCC and then check if you receive an error message.

  If you are unable to remove the CCC, and then run the Fixit.

  The problems that the programs cannot be installed or uninstalled
  http://support.Microsoft.com/mats/program_install_and_uninstall/en?WA=wsignin1.0

  ATI - Forums
  http://forums.AMD.com/game/categories.cfm?CATID=260&forumid=11

  ATI - Support and drivers
  http://support.AMD.com/us/pages/AMDSupportHub.aspx

  Hope this information helps.

• Cannot start the editor of the network and receive a "Virtual ethernet = failed' message when recompiling"

  Hello

  I'll have this error weird - I never had when running VMWare on Windows XP - Linux 6.5 VMWare on Kubuntu 9.04 who cannot open the network Editor, just after I type my user password in the gksudo crushing of the network Editor window and refuse to start. I have this question in a new installation of Kubuntu 9.04 with all the patches with kernel 2.6.28 - 15-generic.

  Any help welcome

  Try from workstation from the command line using the following syntax to see if you still have questions

  VMWARE_USE_SHIPPED_GTK = force vmware

• SubVIs cannot reference the Parent controls

  Is there anyway that a Subvi can reference controls on the façade of a relative of VI? Without this ability, it is difficult to reduce the complexity of a VI using subVIs, when a front panel control is involved. Variable property nodes do not seem to be the ability to reference a control in a VI parent. Is it possible to fix this?

  There are two ways to do this:

  1. use the connector pane to indicate the reference to control of the Subvi.

  2. open a VI reference to parent VI or get the reference through the connector pane. Use the [VI:Controls] property node to get references to all of the controls. You must use a loop to get good verification of the label control. As far as I know, the sequence is in the tab order in order to be able to use an index.

• Scrolling the mouse not working not not to scroll through the pages. cannot change the Volume control. How to fix?

  Original title: scroll of the mouse wheel only adjusts the volume. How to scroll through the pages again?

  Using the wireless mouse (Silvercrest MTS2218-m with win 7 x 64) and scroll wheel is no longer made scroll page up and down in any program. Only, it adjusts the volume. How to scroll through the pages again?

  Already checked the settings in Control Panel > mouse nothing obvious here to change this annoying feature. And have already uninstalled the driver for the mouse in Device Manager but no change. have also stopped and started several times laptop.

  Close to the scroll wheel is a dpi button, which can also be used to pass
  between normal mode and media holding for 3 seconds. In media mode
  the volume control wheel and does not scroll.
  Read the manual... ;-)

• What to do with it? "cookies dir: cannot make the folder /cookies: Permission denied (error 13).

  What to do in this case?

  dir of cookies: can not make the /cookies file: Permission denied (error 13)

  Re: Installing Desktop Cloud Creative, but I got error 13 a permission on my MacBookPro question, why?

• Cannot find the data control to the Web Service in the Menu

  Hello
  
  I try to call a web service in the ADF. To do this, I want to create a web service data command
  
  If I understand correctly, if I right click on the template project, I see the data control from the Web Service under layer Business > Web Services. (as indicated in 2.1 Sec-http://www.oracle.com/technology/products/jdev/howtos/1013/wsadf/adfcomplexwstypes.html#WsProxyPojoControl)
  
  However, I am not able to find this entry in there.
  
  I tried the following things:
  
  I tried with Jdev 10.1.3.5, 10.1.3.4 and 10.1.3.1
  I tried to select all available models of technology to create applications
  -Any model
  -Web Application [JSF, EJB, Toplink]
  -Web Application [JSF, ADF]
  -Web Application [JSF, EJB
  -Web Application [JSF, Struts, ADF]... .and everthing else...
  
  I still don't see the web service proxy.
  
  Then I opened the ADFToystore sample application, and I could see the service data Web controls here!... .that mean my jdev is not defective... something else is missing.
  
  So, I tried to see what libraries are selected... I saw that a library named 'Web Service Data Control' are there in the project, which is not there in the model applications project that I created. So I added this library to the project, but it still does not work...
  Next, I added all THE libraries I have seen in the libraries in the project properties section... still no luck
  
  I don't know I'm missing something basic. Can someone please help.
  
  Rgds,
  Amit

  Hi Amit,

  try to set the filter above in New Gallery to filter by: all Technologies

  Kind regards

  Branislav

• T400, cannot start the Catalyst Control Center - error 'GPU active not supported'.

  on a machine running vista business 64-bit current t400.

  last week all was hunky dory.  This week, when I try to open my ati catalyst (CCC) control center, I have the following error:

  "ATI catalyst control center cannot be started because the active gpu is not managed.

  I read a few posts on this problem from not using the ATI graphics card and being rather on the integrated graphics card.  indicate the positions I could reactivate CCC simply by clicking on the battery icon in the system tray and selecting "mode high performance" to force the machine to use the discreet graphics card.  After I do and then try to start the CCC, I get the same error as above.  at this point after switching to the mode high peformance, my device manager also lists "mobile Intel (r) 4 series express chipset family ' as my graphics again.  If I have left or right click on the battery icon in the status bar, I don't see any options for explicitly switching cards.

  the card driver intel 4 mobile is listed as being from ATI to version 8.520.4.4000.

  I'm not sure of my version of the driver for the ATI card.  and I don't know where to look for it.

  to my knowledge, nothing but a number of 'critical' windows updates have changed on my system between the time when CCC was working last week now.

  any suggestions on how to fix this?  and what it does to stop working?

  Thanks in advance for any help.

  I finally thought to it.  and no new drivers or relocations were necessary.  at the end of the day, all I had to do was turn on version lenovo Power Manager (which appear in my taskbar like a horizontal green battery with the number of minutes of use remaining).  from there I can left click and access the menu that has the switchable graphics option where I can choose the economy of energy or high performance.  If a from there, I select high performance, I can then open CCC.

  the important thing please note this is to access this menu, you must be using power management program of LENOVO thinkVantage (sticking the Green battery on your taskbar icon), NOT windows built in the power manager, which appears as a vertical grey/blue /? battery in the tray system (at least on mine).  Once you have, you can explicitly pass the graphics cards.

  the strange thing is, I had been accessing CCC without explicitly switching the cards without problem until last week.  so in a way that the default setting should of spent high-performance energy saving, thus putting me on the integrated graphic card unless I went it manually.  weird.

  slide, thank you for your help.  I appreciate it.  and it is an interesting note on freeing more memory by disabling the switchable graphics.  I'll probably this give it a shot and see how I like it.  memory is never bad!

  Thanks again to everyone who helped.

• Cannot change the parental control to my admin account. Error message

  When to my admin account, I was able to turn parental controls for UAS oin my children, but when I try to change the programs and other whatnot (so my 5 & 3 years can not access to Quickbooks, etc!) I get an error message saying ' impossible changes to parental controls settings. "  If the problem persists, see your system administrator. "Computer is not on a network and with hunting 4 children I just can't find the time to sit down and understand the problem.  Help!

  http://www.bleepingcomputer.com/tutorials/tutorial139.html

  Link above has a very good tutorial on how to set up Parental controls.

  http://www.Vistax64.com/tutorials/95139-parental-controls-Setup-use.html

  Also, read the tutorial above and the 'Related links' tutorials to vistax64.com.

  Both of the above are very good tutorials for any problem with Parental control.

  See you soon.

  Mick Murphy - Microsoft partner

• Cannot open the iCloud Control Panel on PC

  I have the iCloud v3.1 Panel installed on my Windows 7 64-bit system. It worked very well with Internet Explorer. I switched to Foxfire and when I try to activate the software I get the message "JavaScript is required. To use iCloud activate JavaScript in your browser and try again... (popup footer says "Would you like to make Internet Explorer your default browser?")
  When I look in Add-ins Foxfire, there is only a Java Deployment Toolkit that is blocked because the plugin is known to have security vulnerabilities.
  I give up... someone can help guide me on this issue. I really wish I could access iCloud without having to use a bookmark every time. Programs Windows is not any version of Java as having been installed.
  Thanks to anyone who responds.

  Any aid given by all those who responded to my question is much appreciated. I was able to get the problem solved by going in the Solution Explorer and activating JavaScript it. This seems to fix the problem and it looks like the iCloud Panel lance now using Explorer to do. That's OK with me, as long as it works.

• Cannot change the volume control appleTV (4th generation)

  Hello. When I change the volume of my control the apple tv do not respond, I tried to change the hdmi and everythibg turned on and outside. I have also tried to change the settings of the tv and went to volume settings apple tv and custumething has changed several times, but it just does not work: / I just got the apple tv for like 1 day ago. Well, I hope you have understood my problem and have an answer for that. Thank you < 3

  Volume changes can be made by using the last Apple TV with Siri > control your TV or receiver with your Siri or Apple TV Remote - Support Apple Remote control

• Last updated, 8 Firefox on Win7, opens Gmail to the list view, but cannot open the editor to read or write e-mail.

  From today, after the most recent update, Firefox 8 on Windows 7, when I opened GMail, I can see the list view, but when I try to open an e-mail to read or answer, I get an error saying GMail failed to load the rich text editor, and I can only see the snippet, without the content of the email.

  It seems to be caused by Adblock Plus 1.3.10. Disable temporarily it allows me to read and compose email normally.