Cannot be stretched vertically DecorativeBox

Similar Questions

• Aurora 30.0a2 toolbar and icons are stretched vertically and out of proportion, how do I solve this problem?

  In the updated changes Aurora 30.0a2, the UI displays the toolbar like stretched vertically. all of the icons seem to be of approximately (1 to 1.5 + /). It is no problem major and really just a minor Visual annoyance but still a bug.

  Image: http://tinyurl.com/qzx8y6y

  Only the toolbar is affected, all other regions keep their ratio of 1 to 1.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Toshiba 42WL863G: stretched 3D content using resolution 1920 x 800

  There is a problem with playback of content 3D SBS USB HD resolution 1920 x 800 (i.e. not 1920 x 1080).

  When activating 3D playbeck the image is stretched format full screen, and so everything is bigger / thinner that should be.

  Playing normal content (no 3D) resolution 1920 x 800 works correctly (black below / above).
  During the transition to 3D scratches disappear and the image is stretched vertically relative to the size of the screen.

  Playing the same content (via USB) on my BD Player (Philips BD8000) gives good results without streching.

  Will there be a future solution for this problem?

  I guess that this happens because the internal s TV media player goes full screen and full hd while playing 3D content.
  Since you're using the resolution of 1920 x 800 rare (Full HD must be 1920 x 1080) the content all seems tense.

  I think that to avoid this 'effect', you would need to play movies in HD (1024 x 720) 3D or FHD (1920 x 1020)

• All my monitor circles became vertical egg. Difficulty?

  Everything on my monitor has seemed normal for years, then, suddenly, a few months ago, all the forms of my circle became forms vertical egg.  Photos are stretched vertically.  How can I fix it?  I think it's a problem of resolution, but I don't know what, or how, the to re-adjust.    * E-mail address is removed from the privacy *

  Right-click on the desktop and select screen resolution.

  Select the menu drop-down next to the resolution and to take one marked recommended.

  This should be the native resolution of your monitor.

• How to vertically Center the text in its container

  If a button or a piece of text, I don't see any way to center the text you type * vertically * in the container.  I'm not talking in the item box.  I mean just the text element itself.  If I size a text box and start typing in it, I should be able to say centered vertically.  That's what I'm looking for anyway.   Help much appreciated.

  Text items cannot be centered vertically as they are not containers. However, you can fake that a very big little thanks to the row height. But this means that if you have a text that spans two lines it would be very remote however

  

• See the "quick tools" vertical button bar.

  Hi everyone,
  
  I currently use Acrobat 9 set up with a customized button bar located on the right of the window (where ''Acrobat X"," " has the menu 'Tools'.") I am forced to migrate to version X for various reasons and need we did have this sidebar.
  
  
  In Acrobat X is a toolbar called " ", "Quick Tools""" that pourrait be configured as in the previous version but this bar peut not move and therefore cannot place it vertically.
  
  You know one way of do, JavaScript code ? Any third party Plug -in ?
  I use Windows 7 and Adobe Acrobat 9 standard and X Standart.
  
  If ce topic has been discussed forgive me I used le Search without results ...
  
  

  The chrome UI in X Acrobat family cannot be customized. The position of the toolbars and panes is fixed, if users can add and remove buttons in the toolbars by using the context menus, they can be moved, désamarrés or replaced.

• Cs4 vertical Configurator Panel resize limit

  Hello

  Maybe this has been mentioned before, but when I try to make a custom for photoshop Cs4, Panel

  the Group seems to have a vertical limit when resizing which is much more than what I initially created.

  For example, this one was created in 71 x 94 and cannot be resized vertically more that the screenshot.

  Anchored or not is the same

  

  I also tried other sizes for the original Panel.

  Someone has an idea?

  Thank you

  Marc

  Hello

  There is a "resize" bug in the Configurator 1.0.

  When you export a Panel and open it the first time, Panel to resize the width and height you assigned as cromaline say, after first Panel only is not resized, given that photoshop will remember last size of your Panel.

  But if you resize it in a larger size exceeds the size by default photoshop (220 * 220), when next time launch photoshop

  Photoshop will remember this size, then you can't resize it smaller.

  There is a solution

  on Windows, system go to folder C: \Documents and Settings\

  Look in the "PanelSizeStore.sol" file and delete it.

  Then restart photoshop, you can see the Panel resize to your original size.

  Kind regards

• video of the webcam seems tense on Mac

  Hello

  in some cases, we found that the image of a webcam seems tense when you use a webcam on a mac. In my case, I used a Logitech C910 (which certainly supports 16:9 resolutions) on a Mac running Mac OS X 10.6.8.

  In my project, I want to show a video webcam in 16 / 9 but want to switch between camera resolutions different 16:9 (480 x 270, 320 x 180, 640 x 360). In Windows, each resolution of the camera sounds good - nothing is stretched. You can check if the image is stretched or not the best holding a round Cup in front of his webcam and check whether it is still round in the video. But when you use a Mac, the video of the webcam seems to sometimes tense. The cut is more round.

  I built a small test application running at http://interactive-pioneers.com/camTest/. It shows three different webcam shows: on the left hand side always resize the video resolution, width and height defined in the drop-down list (4:3 and 16:9). The video in the Middle will always be 16:9 with a fixed size of 320 x 180. The video on the right side will always be 4:3 with a fixed size of 320 x 240. Whenever you change the drop-down list, the size of the webcam will be updated via camera.setMode.

  Under Windows, everything works as expected:

  -video on the left: Cup is always round, no stretch

  -video at the Center: cutting is always round every time that a 16:9 resolution is chosen. Cup is stretched vertically whenever a 4:3 resolution is chosen

  -video right: cutting is always round every time that a 4:3 resolution is chosen. Cup is stretched horizontally whenever a 16:9 resolution is chosen

  It's what I expected totally. It is logical.

  But not on a Mac:

  -video on the left: Cup is round for 320 x 240 (4:3), 320 x 180 (16:9) and 640 x 480 (4:3). She is stretched vertically for 480 x 360 (4:3) and 480 x 270 (16:9). It is stretched horizontally to 640 x 360 (16:9). It makes no sense to me. It should be round in all cases as it does under Windows.

  -video at the Center: Cup is round for 320 x 180 (16:9) and 480 x 360 (4:3). She is stretched vertically to 480 x 270 (16:9). It is stretched horizontally to all other resolutions. It would make sense that the Cup is round for all resolutions of 16:9 as well as Windows.

  -video right: Cup is round for 320 x 240 (4:3), 640 x 480 (4:3) and 640 x 360 (16:9). She is stretched vertically for all other resolutions. It would make sense that the Cup is round for all 4:3 as well as Windows resolutions.

  Due to this test result, I'm not able to show a 16:9 video on Mac webcam which is not stretched in some resolutions of 16:9.

  Is it possible to get around this problem?

  You can find the screenshots with the Cup here: http://interactive-pioneers.com/camTest/cam_squeeze_images.zip

  Thanks for your help.

  Malta

  The driver and the camera are certainly responsible. The work of pilots is to validate the incoming request for a resolution against the cameras features and a food that is as close as possible to the he hand. The camera is clearly send a stream. What we cannot say if it's the driver or the camera. Installation of the Logitech driver, even temporarily, can solve this issue.

  If it's the driver, then when you ask for a resolution, it checks the capabilities of the camera and most likely Gets the next highest resolution, it extends to your request and sends it back.

  If it's the camera, then she does something very similar. The pilot did a request for resolution, the camera knows he does not support this resolution and sends something higher awaits the driver to "solve" the problem, but the UVC driver blindly returns data to the requested resolution.

  Usually always install you the driver under windows and/or there is already one that is completely capable installed by default, you always receive the best experience.

  Good luck!

• Place the cursor where wanted / needed (like arrow key functionality)

  I have a hard time placing the cursor exactly where I want to.  This happens often when I have typo in an area like text or hyperlinks.  Given that these areas cannot be stretched or expanded, I have fat fingers... which often leads to place me the cursor in the right place.  I keep wanting to the arrow keys to move to the correct place.  I forget this feature, or am I destined to continue my hunt and Peck, Peck, Peck... method?

  Thank you!

  Place the cursor in the field you want to change. Press in and hold the orange key and scroll your finger to the left or to the right depending on how you need to change the text.

• Border in black screen HP Mini 210, screen shifted downwards - problem after power outage

  HP Mini 210-1000 actually it's HP Mini 210-1060 EV PC

  Some specifications:

  Display: 25.6 cm (10.1 ") diagonal WSVGA LED HP BrightView Infinity Widescreen Display (1024 x 600) SUBMISSION

  Battery has been dead for a long time.

  My display drivers and BIOS have been recently updated from the HP website.

  After a power failure and a reboot, the screen looks weird. It was moved about an inch down with a black border at the top, on which the mouse won't and the task bar is not visible, as is the bottom of the screen.

  When I go to the screen resolution in Windows by right-clicking on the desktop resolution is set at 1024 x 768, when I click on advanced settings, the monitor tab, monitor is set as a Monitor (1024 x 768 60 Hz) generic Non-PnP.

  When I change to 1024 x 600 it seems blurred and stretched vertically, but the screen is always shifted down with black border on top.

  When I get the Intel graphics settings I can make the same changes as in the dialog Windows (640 x 480, 800 x 600, 1024 x 600, 1024 x 768).

  In image format Options when I select full-screen (non-frontiere) the black border is fixed but always tense vertical screen but the screen is cut down with no visible taskbar.

  Graphics driver reinstalled so that some Type Monitor of windows drivers, nothing changes.

  When I turn on the laptop, the screen HP Quickweb appears also as a 1024 x 600 stretched vertically without black border at the top but will disable the display down.

  It seems that Windows and Hp Quickweb see at 1024 x 768 60 Hz display after the power failure.

  Before that, I had installed Windows updates, but nothing on the display drivers.

  I only got a point system restore leave on earlier that day (very low disk space?) but that did nothing.

  Guess it is a registry/driver issue since no pixel is bad and the black border on top is set in image format Options when I select full-screen (sans-bordure). Any suggestions please?

  Of the information system

  Model: HP Mini 210-1000 actually it's HP Mini 210-1060 EV PC
  Name of the operating system: Microsoft Windows 7 Starter 32-bit
  Version: 6.1.7601 Service Pack 1 Build 7601
  The version of the BIOS/Date: Hewlett-Packard F.24, 18/03/2011

  Display:
  Name: Intel(r) Graphics Media Accelerator 3150
  PNP device ID: PCI VEN_8086 & DEV_A011 & SUBSYS_3660103C & REV_00\3 & 21436425 & 0 & 10
  Adapter type: Intel(r) Graphics Media Accelerator 3150, compatible Intel Corporation

  Name: Intel(r) Graphics Media Accelerator 3150
  ID device PNP PCI VEN_8086 & DEV_A012 & SUBSYS_3660103C & REV_00\3 & 21436425 & 0 & 11
  Compatible adapter Type not available, Intel Corporation

  SOLVED.

  After noticing the OS startup screen/HP resolution looked normal, I just removed the plastic bottom and hit the CMOS battery, after reading this somewhere, because the audio drivers and webcam have been uninstalled too whenever I rebooted the netbook.

  He has not moved even because it was recorded well.

  So I restarted and the resolution has been set.

  Now, can't make the webcam work even though I reinstalled the driver...

• [SOLVED] Is it possible to look at pictures 3D (JPS or FTU) on a Sony Bravia TV Android?

  As the title says.

  I have several jps and drag files DFO taken with different smartphones equipped with 3D camera, stored in a USB key. None of these files are even recognized by my TV (folder appears as empty).

  In contrast, 3D (SBS .mp4 format) videos, I've shot with the same set of smartphones without any kind of problems and in 3D.

  Then... thumbdrive is it possible to display photos stored 3D (mpo format or jps) in a USB port on my Sony Bravia TV Android?

  It is worth noting that apps like MX Player Pro can also play videos in 3D in 3D, so an Android app can send the stereo signal to the control panel. Then... there at - it an Android app that can do the trick?

  Now, in order to view the pictures in 3D, I need to plug my smartphones to the HDMI input, but because the signal is upscaled 800 x 480, the quality that results is very low.

  PS: If there is no way to make the TV read JP and DFO, there Blu - Ray drives that can read jps or FTU from a USB?

  (answer my own question since she will probably never get answered, but the solution requires a conversion and kludgy).

  How to convert mass of 3D photos and view them with your Bravia 3D glasses:

  Step 1 (conversion of the photo in jpg format):

  If your 3D photo is FTU: open the StereoPhoto Maker windows desktop app, go to file-> open a stereo Image, then click on the file-> save stereo Image. Save it as "JPEG file", make sure that "Always save SBS format" is selected and that the quality is set to 99 (the most high, since this picture will go through another conversion). Or you can use the conversion application multi feature even the to do in the batch.

  If your 3D photo is jps: just rename photo.jps in photo.jpg but here's a much smarter way to do it in bulk: create a folder on C: no spaces inside (say "3Dphotos"). Then open the cmd (find it in the start menu) type cd C:\3Dphotos and then type rename *.jps *.jpg

  You should now have a JPG file which has both left and right-by-side eye

  Step 2 (resizing):

  You need in bulk - resize pictures 1920 x 1080 (each eye will be 'stretched' vertically). Go to bulkresizephotos dot com choose the jpg photos of step 1 (20-30 pictures at the same time preference) then click on 'Exact size' then click on 'Pro', then 'no. Padding. Make sure 'Format of Image' is JPEG (you can experiment with other formats, but it works), and the quality is set to one between 95-99. Then click Start resizing.

  You just convert your photos to the half-SBS Full HD format, in bulk. Save pictures to a USB key.

  Please note that you must select 1920 x 1080 as your size, even if your photos are not widescreen.

  Step 3 (visualization):

  Now, all you have to do is view photos on your Bravia. You can use any joint Bluray player/Media player / whatever to view the photos. As long as it is connected via HDMI. Then, press the 'Action' Menu-> 3D-> 3D display and select side. Boom! 3D pictures!

  If your Bravia is an Android TV, it is also possible to download Kodi and view pictures from there. But, the Action Menu doesn't have a "3D" option not in mode 'HDMI', then you will need to download app 'SideView of video and TV' Sony and push the button of the remote 3D.

• Suddenly can't see s icon taskbar

  

  For some reason, the icons in my taskbar to the right and the lettering for the Start button have changed so I can't see them.  In fact, the appearance of the taskbar itself is different.  It has a thin grey line at the top of the taskbar that I don'ty remember being there before and the Start button, the icon of Windows seems differnet. I includes a Snip of the foregoing.  I tried to enlarge, but Snip only stretch vertically, not horizontally so that it looks a bit distorted above.  You should be able to see where the date and time are very light.  It happened today and I'm not aware of any uodates or changes that I could maybe have done.   I really want them back the way they were before.   Is there a way to change the color of the icons/lettering so they contrast with the color of the taskbar?

  Hello.  Thanks for the reply.  I had not gotten a response for a few days and noticed the problem began just after a recent Windows Update.  I checked my update history and noted that the Office of Bing had recently been installed, but the system had not been rebooted since the installation.  I rebooted and it couldn't see anything on my desktop at all.  All my icons disappeared, and was therefore a taskbar at all.   I fiddled around for a bit and could finally see the Start button.  I "uninstalled" the Office of Bing and rebooted.  Everything is back and my taskbar looked normal.    I think I'll leave it alone for now and not to reinstall the update of Bing.

• BlackBerry Smartphones google maps keyboard

  I have problems with google maps. First of all, I downloaded google maps and was able to see a complete view of the maps on my screen and succeeded in horizontal or vertical mode. Now I cannot see on vertical display and should not hide the key board. Anyone having the same problems?

  Hi and welcome to the forums!

  I had the same problem with Google maps. Drove me crazy!

  Finally, I've read enough and solved in this way.

  options, options, advanced applications allow the table build completely.

  Highlight Google maps and press the menu button, then select Disable compatibility mode.

  Worked for me!

  Thank you

  Bifocals

• Why is my 3D can label distorted?

  I work at the CS6.

  I'm trying to display a label wrapped around a drum. I saved the label as a symbol and it mapped to the can, but the label is vertically distorted and truncated.

  Here is a sample test made of squares and a circle. When I wrap this and discovers the bottle straight, black squares are stretched vertically (and not uniformly) and the circle becomes a deformed ellipse. The lines at the top and bottom edges are truncated. This happens with any of the x, y and z display settings.

  I don't understand why this is happening and how to fix it.

  Any help appreciated.

  

  The handles are your problem.

  You need to remove the handles on both sides of the straight segment.

  After that, you will need to readjust the mapping, because there will be more sides. But then it will work:

  https://DL.dropboxusercontent.com/u/15485305/3D-mapping-handles.mov

• Header created in Muse is compressed in the web browser

  I am currently rethinking my website using Muse CC.  My header image looks cropped get when displayed in the browser Chrome Web.

  This is how it looks in the design view.

  

  And that's how is looks like the Chrome browser

  

  as you can see half of the image is missing.

  I have inserted the picture with a rectangle 1160 x 119 px.

  Fill the rectangle with the image, then set it to scale to fill.

  When I put it on the scale, it populates only 50% of the width of the browser.

  The hairpin at the top left image.

  However, I lose half of the image when displaying in the web browser.

  I use window 10 home.

  Can someone tell me what the situation could create this problem please.

  I think that this behavior is partially expected...

  I can't reproduce your problem completely, although I have created a similar layout.

  The fact that a part of the bottom is cut off, can be explained by the fact that an element of browser to scale as this framework, is allowed to extend beyond the initial width of its width. So, after that 1160 pixels, the image stretches vertically and horizontally to keep its proportions, but greater than the frame height.

  What I find strange is that it cuts both sides, and you said that you set to have its point of origin at the top left.

  Of 50% might have something to do with a setting HiDPI.

  Could you put the example on the line so we can have a better look at it?