cannot ping between remote vpn site?
vpn l2l site A, site B is extension vpn network, connect to the same vpn device 5510 to the central office and work well. I can ping from central office for two remote sites, but I cannot ping between these two vpn sites? Tried to debug icmp, I can see the icmp side did reach central office but then disappeared! do not send B next? Help, please...
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
!
object-group network SITE-a.
object-network 192.168.42.0 255.255.255.0
!
object-group network SITE-B
object-network 192.168.46.0 255.255.255.0
!
extended OUTSIDE allowed a whole icmp access list
HOLT-VPN-ACL extended access-list allow ip object-CBO-NET object group SITE-a.
!
destination SITE-a NAT (outside, outside) static source SITE - a static SITE to SITE-B-B
!
address for correspondence card crypto VPN-card 50 HOLT-VPN-ACL
card crypto VPN-card 50 peers set *. *.56.250
card crypto VPN-card 50 set transform-set AES-256-SHA ikev1
VPN-card interface card crypto outside
!
internal strategy group to DISTANCE-NETEXTENSION
Remote CONTROL-NETEXTENSION group policy attributes
value of DNS server *. *. *. *
VPN-idle-timeout no
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value REMOTE-NET2
value by default-field *.org
allow to NEM
!
remote access of type tunnel-group to DISTANCE-NETEXTENSION
Global DISTANCE-NETEXTENSION-attributes tunnel-group
authentication-server-group (inside) LOCAL
Group Policy - by default-remote CONTROL-NETEXTENSION
IPSec-attributes tunnel-group to DISTANCE-NETEXTENSION
IKEv1 pre-shared-key *.
tunnel-group *. *.56.250 type ipsec-l2l
tunnel-group *. *.56.250 ipsec-attributes
IKEv1 pre-shared-key *.
!
!
ASA - 5510 # display route. include the 192.168.42
S 192.168.42.0 255.255.255.0 [1/0] via *. *. 80.1, outside
ASA - 5510 # display route. include the 192.168.46
S 192.168.46.0 255.255.255.0 [1/0] via *. *. 80.1, outside
ASA-5510.
!
Username: Laporte-don't Index: 10
Assigned IP: 192.168.46.0 public IP address: *. *.65.201
Protocol: IKEv1 IPsecOverNatT
License: Another VPN
Encryption: 3DES hash: SHA1
TX Bytes: bytes 11667685 Rx: 1604235
Group Policy: Group remote CONTROL-NETEXTENSION Tunnel: remote CONTROL-NETEXTENSION
Opening time: 08:19:12 IS Thursday, February 12, 2015
Duration: 6 h: 53 m: 29 s
Inactivity: 0 h: 00 m: 00s
Result of the NAC: unknown
Map VLANS: VLAN n/a: no
!
ASA - 5510 # display l2l vpn-sessiondb
Session type: LAN-to-LAN
Connection: *. *.56.250
Index: 6 IP Addr: *. *.56.250
Protocol: IPsec IKEv1
Encryption: AES256 3DES hash: SHA1
TX Bytes: bytes 2931026707 Rx: 256715895
Connect time: 02:00:41 GMT Thursday, February 12, 2015
Duration: 13: 00: 10:00
Hi Rico,
You need dynamic nat (for available IP addresses) for the two side to every subset of remote access to the other side remote subnet and so they can access every other subnet as if both from the traffic from your central location.
example:
Say, this IP (10.10.10.254) is unused IP to the central office, allowed to access remote tunnel 'A' and 'B' of the site.
object-group network SITE-a.
object-network 192.168.42.0 255.255.255.0
!
object-group network SITE-B
object-network 192.168.46.0 255.255.255.0
dynamic source destination SITE-a. 10.10.10.254 NAT (outdoors, outdoor)
public static SITE SITE-B-B
destination NAT (outdoors, outdoor) SITE-B 10.10.10.254 dynamic source
SITE static-SITE a
Hope this helps
Thank you
Rizwan James
Tags: Cisco Security
Similar Questions
-
Hi all
I have a client who uses a 506e with the cleint 4.02 for the remote VPN Cisco. The pix is multiple inside roads. The first network inside is 192.168.1.X and E1 of the 506 is 192.168.1.1. The second network is 10.71.56.X.
The problem is as soon as the VPN is connected I can ping any host on the 192.168.1.X, but not anything on the 10.71.56.X network. Without netbios or the other. From the PIX, I can ping hosts on two internal networks.
Here is the config below. Thank you!
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the password xxxxx
passwd xxxxxxx
hostname GNB - PIX
cisco.com-domain name
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
QUBEADMIN tcp service object-group
Beach of port-object 444 444
outside_access_in list access permit tcp any host 12.X.X.X eq pop3
outside_access_in list access permit tcp any host 12.X.X.X eq smtp
outside_access_in list access permit tcp any host 12.X.X.X EQ field
outside_access_in list access permit tcp any host 12.X.X.X eq www
outside_access_in list access permit tcp any host 12.X.X.X QUBEADMIN object-group
outside_access_in list access permit icmp any any echo response
access-list outside_access_in allow icmp all once exceed
outside_access_in list access permit tcp any host 12.169.2.21 eq ssh
GNB_splitTunnelAcl ip 10.71.56.0 access list allow 255.255.255.0 any
outside_cryptomap_dyn_20 ip access list allow any 10.71.56.32 255.255.255.224
pager lines 24
opening of session
timestamp of the record
logging paused
logging buffered stored notifications
Logging trap errors
notifications to the history of logging
the logging queue 0
host of logging inside the 10.71.55.10
logging out of the 192.104.109.91 host
interface ethernet0 car
Auto interface ethernet1
ICMP allow any inside
Outside 1500 MTU
Within 1500 MTU
IP address outside 12.X.X.X 255.255.254.0
IP address inside 192.168.1.254 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
local IP VPNPOOL 10.71.56.40 pool - 10.71.56.50
history of PDM activate
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
public static 12.X.X.X (Interior, exterior) 192.168.1.1 mask subnet 255.255.255.255 0 0
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 12.X.X.X 1
Route inside 10.71.55.0 255.255.255.0 192.168.1.1 1
Route inside 10.71.56.0 255.255.255.0 192.168.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
ISAKMP allows outside
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
vpngroup address VPNPOOL pool GUARD
vpngroup dns-server 10.71.56.10 GNB 10.71.56.10
GNB GNB_splitTunnelAcl vpngroup split tunnel
vpngroup GNB 1800 idle time
GNB vpngroup password *.
Telnet timeout 5
SSH timeout 60
Terminal width 80
Cryptochecksum:XXXXX
: end
[OK]
GNB - PIX #.
You use 10.71.56.0 255.255.255.0 in two places
you route to it via 192.168.1.1, but you're also allocation of addresses for vpn clients. Guests who are on the segment 10.71.56.0/24, if they manage to get the connected vpn client package (which is assigned a 10.71.56.x) address, would not send the response packet to this request on the local subnet, the router that has the 192.168.1.1 interface, which is what would be needed to make it work.
You must use a different network for your vpn clients block - you cannot use the same ip through two different networks space.
-
QuickVPN - could not do a ping the remote VPN router!
Hello
I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.
Here is the Log of the QuickVPN client.
2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
2008-10-15 20:14:38 [STATUS] connection...
2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
2008-10-15 20:14:44 [STATUS] commissioning...
2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
2008-10-15 20:14:51 [STATUS] verification of network...
2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
2008-10-15 20:15:19 [STATUS] disconnection...
2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.
There is a way to disable the Ping process and continue with the VPN connection?
QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.
Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.
You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.
What is the router that is connected to the computer? How is it that is configured?
-
Routing of traffic between two VPN Site-to-Site Tunnels
Hi people,
I am trying to establish routing between two vpn Site-to-Site tunnels which are destined for the same outside the interface of my Cisco ASA.
Please find attached flowchart for the same thing. All used firewalls are Cisco ASA 5520.
Two VPN tunnels between Point A and Point B, Point B and Point C is too much upward. I activated same command to permit security level interface also intra.
How can I activate the LAN subnets traffic behind Point to join LAN subnets behind C Point without having to create a tunnel separated between Point A and Point C
Thank you very much.
Hello
Basically, you will need to NAT0 and VPN rules on each site to allow this traffic.
I think that the configurations should look something like below. Naturally you will already probably a NAT0 configuration and certainly the L2L VPN configuration
Site has
access-list NAT0 note NAT0 rule for SiteA SiteC traffic
access-list allowed NAT0 ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note L2L-VPN-CRYPTO-SITEB access-list interesting traffic for SiteA to SiteC
access-list L2L-VPN-CRYPTO-SITEB permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteA LAN to LAN SiteC traffic must use the VPN L2L existing SiteB
Site B
access list OUTSIDE-NAT0 note NAT0 rule for SiteA SiteC traffic
OUTSIDE-NAT0 allowed 192.168.1.0 ip access list 255.255.255.0 192.168.3.0 255.255.255.0
NAT (outside) 0-list of access OUTSIDE-NAT0
Note L2L-VPN-CRYPTO-SITEA access-list traffic for SiteA to SiteC through a Tunnel between A - B
access-list L2L-VPN-CRYPTO-SITEA ip 192.168.3.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Note L2L-VPN-CRYPTO-SITEC access-list traffic for SiteA to SiteC through a Tunnel between B - C
access-list L2L-VPN-CRYPTO-SITEC permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- OUTSIDE-NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic. It is this time tied to the 'outer' interface, as traffic will be coming in and out through this interface to SiteB
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEA (and SITEC) = are the ACL in the configurations of VPN L2L that defines the SiteA LAN to LAN SiteC traffic should use existing VPN L2L connections.
Site C
access-list NAT0 note NAT0 rule for SiteC SiteA traffic
NAT0 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note list-access-L2L-VPN-CRYPTO-SITEB SiteC to SiteA interesting traffic
L2L-VPN-CRYPTO-SITEB 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteC to SiteA NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteC LAN to LAN SiteA traffic must use the VPN L2L existing SiteB
To my knowledge, the foregoing must manage the selection NAT0 and traffic for VPN L2L connections. Naturally, the Interface/ACL names may be different depending on your current configuration.
Hope this helps
-Jouni
-
Cisco ASA 5520 cannot ping between VPN Tunnels
I have the main site and sites A and B. A to connect to the hand and B connects to the main. I can ping from A hand and has for main. I can ping from main to B and B to main. However, I can not ping from A to B. A and B are sonicwall 2040 and main is a 5520. The question should not be with the 5520 none allowing traffic between the two VPN Tunnels, but I can't understand why it does not work. Can someone give an idea on that? Thanks in advance.
Hello
I see that you use ASDM. Always makes my eyes bleed when I need to look at the DM_INLINE of named objects and try to make sense the CLI format
Seems to me that there are problems with the NAT.
If you don't mind a small break between the main Site and remote locations, I'd say changing some follows the NAT configuration
Remove old
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_10 DM_INLINE_NETWORK_10 non-proxy-arp-search of route static destination
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_12 DM_INLINE_NETWORK_12 non-proxy-arp-search of route static destination
Add a new
object-group network NETWORK-2790
object-network 10.217.0.0 255.255.255.0
object-network 10.217.1.0 255.255.255.0
object-group network NETWORK-3820
object-network 10.216.0.0 255.255.255.0
object-network 10.216.1.0 255.255.255.0
object-group network NETWORK-COLO
object-net 10.8.0.0 255.255.255.0
destination of NETWORK of NETWORK-2790-2790 static NAT (outside, outside) static source NETWORK - 3820 - 3820
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 2790 - 2790
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 3820 - 3820
The first new line of configuring NAT manages the NAT0 configuration for traffic between SiteA and SiteB. The following configurations of NAT 2 manage the NAT0 for traffic between the main Site - hand Site SiteA - SiteB
-Jouni
-
Cannot access remote VPN site-to-site VPN
Internal network: 192.168.0.0/16
The remote VPN Clients: 192.168.0.100 - 192.168.0.254
Remote (L2L) network: 10.10.10.0/26
Remote VPN Clients are able to access the internal network without problem, but are unable to access the remote 10.10.10.0. Is it possible to debug this? "packet - trace" show no problem...
Hi Ben,
Please create a no. - nat on the external interface, because your customers to vpn-remote and remote-L2L tunnels are located on outside interface (i.e. from the outside). You should treat your outside network identical to your inside network, as you would create a no. - nat for your inside networks.
The ACL you create for the no - nat outside must be in both directions as below.
permit access ip 192.168.0.0 scope list outside_nat0 255.255.255.0 10.10.10.0 255.255.255.192
outside_nat0 to access extended list ip 10.10.10.0 allow 255.255.255.192 192.168.0.0 255.255.255.0
NAT (outside) 0-list of access outside_nat0
permit same-security-traffic intra-interface
Pls let me know, if this is useful.
Thank you
Rizwan James
-
Cannot ping ASA remote on an L2L
I have an ASA5520, and about 10 of 5505. Site running all at the Sites. The tunnels are in place and everything worked fine. Well on the side room, I cannot ping the ASA remote, but I can ping all devices behind it. On the remote side I ping the 5520 and everything else on my network I encouraged. When I look at the newspaper of the ASDM on the 5520, that there is no evidence related to the ping for the 5505. I don't see where it blocks the ICMP on the 5505. It just says:
"6 August 14, 2008 05:40:49 302020 10.0.3.69 192.168.1.101 built outgoing ICMP connection for faddr gaddr laddr 192.168.1.101/0 192.168.1.101/0 10.0.3.69/512.
and
"6 August 14, 2008 05:40:49 302021 10.0.3.69 192.168.1.101 connection disassembly ICMP for faddr gaddr laddr 192.168.1.101/0 192.168.1.101/0 10.0.3.69/512.
It is a normal traffic for a S2S I guess. While I am trying to get this to work I have it configured,.
ICMP allow any inside
"ICMP allow all outside.
Any suggestions?
If you try to ping inside the interface through the tunnel, try to add...
management-access inside
-
Can not pass traffic from the VPN client to remote VPN site to site
Hello
I can't get the traffic flowing between my VPN clients and my remote site-to-site VPN, I did step by step in this link:
my firewall says that the package is abandoned by statefull inspection.
But this should be the command "same-security-traffic..." "this problem must be resolved
% ASA-6-302020: built ICMP incoming connections for faddr gaddr laddr (nworks) 10.48.100.2/0 10.48.100.2/0 10.45.231.163/1
% ASA-6-302020: built outgoing ICMP connection for faddr gaddr laddr 10.45.231.163/1 10.45.231.163/1 10.48.100.2/0
% ASA-6-302021: disassembly ICMP connection for faddr gaddr laddr (nworks) 10.48.100.2/0 10.48.100.2/0 10.45.231.163/1
% ASA-6-302021: disassembly ICMP connection for faddr gaddr laddr 10.45.231.163/1 10.45.231.163/1 10.48.100.2/0
Is it all what you might think that I'm missing?
Best regards
Erik
Erik,
Please check it out because no decaps means the ASA does not what it is the other side of the tunnel.
If you send traffic and you will see the crypt increment... but nothing in return... 99% sure that the problem is at the other end.
Federico.
-
Tunnel remote VPN Site to Site
Hello
I am facing a problem with my remote VPN users, I describe my network here. I have a site to another tunnel for my USA, tht IP 169.X.X.X. office client, we are able to connect this tunnel. now I configured remote vpn for users of my home, my office inside the IP is 192.168.2.X and once I connect to home, in the office through vpn cisco client, then, my ip is 192.168.3.X I put the IP in ASA pool, now 192.168.3.X and 192.168.2.X communicates correctly , but I need to access my Tunnel IP 169.1.X.X also from 192.168.3.X (Home).
203.92.X.X is my static public Ip address that is allowed in the client side for the tunnel.
If something confussing please let me know.
Thank you
Nitin
Nitin,
It is not possible to have a NATing on 192.168.3.0/24 to public ip address because it has default route (which you can reach L2L remote host) on the SAA pointing to the external interface. This default route will be redirect/road traffic on the external interface only vpn client so NATing will reach us.
HTH
Sangaré
-
Cannot ping via the VPN client host when static NAT translations are used
Hello, I have a SRI 3825 configured for Cisco VPN client access.
There are also several hosts on the internal network of the static NAT translations have a services facing outwards.
Everything works as expected with the exception that I cannot ping hosts on the internal network once connected via VPN client that is internal IP addresses have the static NAT translations in external public addresses, I ping any host that does not have static NAT translation.
For example, in the example below, I cannot ping 192.168.1.1 and 192.168.1.2, but I can ping to the internal interface of the router, and any other host on the LAN, I can ping all hosts in the router itself.
Any help would be appreciated.
Concerning
!
session of crypto consignment
!
crypto ISAKMP policy 10
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group vpnclient
key S3Cu4Ke!
DNS 192.168.1.1 192.168.1.2
domain domain.com
pool dhcppool
ACL 198
Save-password
PFS
netmask 255.255.255.0
!
!
Crypto ipsec transform-set-SECURE 3DES esp-3des esp-sha-hmac
!
Crypto-map dynamic dynmap 10
86400 seconds, life of security association set
game of transformation-3DES-SECURE
market arriere-route
!
card crypto client cryptomap of authentication list drauthen
card crypto isakmp authorization list drauthor cryptomap
client configuration address card crypto cryptomap answer
map cryptomap 65535-isakmp ipsec crypto dynamic dynmap
!
interface GigabitEthernet0/0
NAT outside IP
IP 1.2.3.4 255.255.255.240
cryptomap card crypto
!
interface GigabitEthernet0/1
IP 192.168.1.254 255.255.255.0
IP nat inside
!
IP local pool dhcppool 192.168.2.50 192.168.2.100
!
Note access-list 198 * Split Tunnel encrypted traffic *.
access-list 198 allow ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255!
Note access-list 199 * NAT0 ACL *.
access-list 199 deny ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255
access-list 199 permit ip 192.168.1.0 0.0.0.255 any!
Sheep allowed 10 route map
corresponds to the IP 199!
IP nat inside source map route sheep interface GigabitEthernet0/0 overload!
IP nat inside source static 192.168.1.1 1.2.3.5
IP nat inside source static 192.168.1.2 1.2.3.6The problem seems to be that static NAT take your nat exemption.
The solution would be:
IP nat inside source static 192.168.1.1 1.2.3.5 sheep map route
IP nat inside source static 192.168.1.2 1.2.3.6 sheep map routeHTH
Herbert
-
problem with users to access remote vpn site to site vpn network
I did the Setup: asa 5510 configured remote access vpn. My vpn users receive asa 5510 range 192.168.50.0/24 addresses and users access my local lan 192.168.0.0/24. the second side of the local lan 192.168.0.0/24 on asa 5505, I did a vpn site-to-site with network 192.168.5.0/24.on that both sides of a site are asa 5505. inside the interface asa 5510 Elise 192.168.0.10 and inside the interface asa 5505 have address 192.168.0.17.third asa 5505 networked 192.168.5.0/24 address 192.168.5.1. I want my remote access vpn users can access resources on network 192.168.5.0/24. I create the static route on inside the asa 5510 static route 192.168.5.0 interface 255.255.255.0 192.168.0.17 and a static route on inside the asa 5505 static route 192.168.50.0 interface 255.255.255.0 192.168.0.10, but it's not working. What do I do?
execution of the configuration of my asa 5510 is
Result of the command: "show run"
: Saved
:
ASA Version 8.4(2)
!
hostname asa5510
domain-name dri.local
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.178 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.0.10 255.255.255.0
!
interface Ethernet0/2
description Mreza za virtualne masine- mail server, wsus....
nameif DMZ
security-level 50
ip address 172.16.20.1 255.255.255.0
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name dri.local
object network VPN-POOL
subnet 192.168.50.0 255.255.255.0
description VPN Client pool
object network LAN-NETWORK
subnet 192.168.0.0 255.255.255.0
description LAN Network
object network NETWORK_OBJ_192.168.0.0_24
subnet 192.168.0.0 255.255.255.0
object network 192.168.0.10
host 192.168.0.10
object service ssl
service tcp destination eq 465
object service tls
service tcp destination eq 995
object network mail_server
host 172.16.20.201
object service StartTLS
service tcp destination eq 587
object service admin_port
service tcp destination eq 444
object service ODMR
service tcp destination eq 366
object service SSL-IMAP
service tcp destination eq 993
object network remote
host 172.16.20.200
object network test
host 192.168.0.22
object network mail
host 172.16.20.200
object network DMZ
host 172.16.20.200
object network Inside_DMZ
host 192.168.0.20
object service rdp
service tcp destination eq 3389
object network DRI_PS99
host 192.168.0.54
object service microsoft_dc
service tcp destination eq 445
object service https448
service tcp destination eq 448
object network mail_server_internal
host 172.16.20.201
object service Acronis_remote
service tcp destination eq 9876
object service Acronis_25001
service tcp destination eq 25001
object service HTTP3000
service tcp destination eq 3000
object network VPNPOOL
subnet 192.168.50.0 255.255.255.0
object-group network PAT-SOURCE-NETWORKS
description Source networks for PAT
network-object 192.168.0.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object admin_port
service-object object ssl
service-object object tls
service-object object https448
object-group service DM_INLINE_SERVICE_2
service-object object admin_port
service-object object https448
service-object object ssl
service-object object tls
service-object tcp destination eq pop3
service-object tcp destination eq smtp
object-group service DM_INLINE_SERVICE_3
service-object object admin_port
service-object object https448
service-object object ssl
service-object tcp destination eq smtp
service-object object tls
service-object object Acronis_remote
service-object tcp destination eq www
service-object object Acronis_25001
service-object object microsoft_dc
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
object-group service DM_INLINE_SERVICE_4
service-object object Acronis_25001
service-object object Acronis_remote
service-object object microsoft_dc
service-object tcp destination eq www
service-object tcp
service-object ip
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 any object mail_server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any object mail
access-list Split_Tunnel_List extended permit ip 192.168.0.0 255.255.255.0 any
access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 192.168.5.0 255.255.255.0
access-list DMZ extended permit object-group DM_INLINE_SERVICE_4 172.16.20.0 255.255.255.0 any
access-list DMZ extended permit object-group DM_INLINE_SERVICE_3 host 172.16.20.201 any
access-list DMZ extended permit object-group DM_INLINE_PROTOCOL_1 172.16.20.0 255.255.255.0 any inactive
access-list DMZ extended deny tcp any any eq smtp
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
ip local pool vpnadrese 192.168.50.1-192.168.50.100 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN-NETWORK LAN-NETWORK destination static VPN-POOL VPN-POOL
!
object network mail_server
nat (DMZ,outside) static x.x.x.179
object network mail
nat (DMZ,outside) static x.x.x.180
access-group outside_access_in in interface outside
access-group DMZ in interface DMZ
route outside 0.0.0.0 0.0.0.0 178.254.133.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action terminate
dynamic-access-policy-record dripolisa
aaa-server DRI protocol ldap
aaa-server DRI (inside) host 192.168.0.20
ldap-base-dn DC=dri,DC=local
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=dragan urukalo,OU=novisad,OU=sektor2,OU=REVIZIJA,DC=dri,DC=local
server-type microsoft
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
virtual telnet 192.168.1.12
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 195.222.96.223
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.0.14-192.168.0.45 inside
!
dhcpd address 172.16.20.2-172.16.20.150 DMZ
dhcpd dns x.x.x.177 interface DMZ
dhcpd auto_config outside interface DMZ
dhcpd option 6 ip x.x.x.177 interface DMZ
dhcpd enable DMZ
!
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
!
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy GroupPolicy_x.x.x.223 internal
group-policy GroupPolicy_x.x.x.223 attributes
vpn-tunnel-protocol ikev1 ikev2
group-policy drivpn internal
group-policy drivpn attributes
dns-server value 192.168.0.20 192.168.0.254
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-tunnel-protocol ikev1 l2tp-ipsec
split-tunnel-network-list value Split_Tunnel_List
default-domain value dri.local
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group drivpn type remote-access
tunnel-group drivpn general-attributes
address-pool vpnadrese
authentication-server-group DRI
default-group-policy drivpn
tunnel-group drivpn ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group x.x.x.223 type ipsec-l2l
tunnel-group x.x.x.223 general-attributes
default-group-policy GroupPolicy_x.x.x.223
tunnel-group x.x.x.223 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect tftp
inspect ip-options
inspect netbios
inspect icmp
inspect http
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:69c651e94663fc570b67e0c4c0dcbae1
: endrunning config asa 5505
Result of the command: "show run"
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password csq7sfr0bQJqMGET encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.5.0 PALATA
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
object-group service DM_INLINE_SERVICE_1
service-object ip
service-object tcp
service-object icmp echo
service-object icmp echo-reply
service-object tcp eq domain
service-object tcp eq ldap
service-object tcp eq smtp
object-group service DM_INLINE_SERVICE_2
service-object ip
service-object tcp eq domain
service-object tcp eq www
service-object tcp eq https
service-object tcp eq smtp
object-group service Sharepoint8080 tcp
port-object eq 8080
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any any
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_2 192.168.0.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list outside_2_cryptomap extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
pager lines 24
logging enable
logging asdm informational
logging mail errors
logging from-address
logging recipient-address level debugging
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 192.168.0.0 255.255.255.0
static (inside,outside) 10.13.74.35 192.168.0.22 netmask 255.255.255.255
static (inside,outside) 10.13.74.34 192.168.0.20 netmask 255.255.255.255 dns
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.13.74.1 1
route inside 0.0.0.0 0.0.0.0 192.168.0.17 tunneled
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication telnet console LOCAL
http server enable
http 10.13.74.0 255.255.255.0 outside
http 192.168.0.0 255.255.255.0 inside
http 10.15.100.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
virtual telnet 192.168.0.53
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_2_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 10.15.100.15
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group 10.15.100.15 type ipsec-l2l
tunnel-group 10.15.100.15 ipsec-attributes
pre-shared-key *
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
!
service-policy global_policy global
smtp-server 173.194.79.109
prompt hostname context
Cryptochecksum:4767b6764cb597f0a7b8b138587d4192
: endThank you
Hello
I have previously edited the my initial response was in fact not necessary since you were actually using full Tunnel
EDIT: Actually just noticed the the VPN client isnt using Split Tunnel. Its Full Tunnel at the moment since it doesnt have the "split-tunnel-policy tunnelspecified"
So you don't really have any of those.
Please mark the question answers and/or assess response
Ask more if necessary
-Jouni
-
Remote VPN site to site vpn on ASA?
Hello
I would like to know if it is possible to have this configuration with an ASA5510:
(1) - remote access VPN (access by the external interface)
(2) - site to site VPN (same access interface)
The goal: users of vpn (1) can access the server remote vpn (2) and vice versa.
Is it possible? and what is the best practice to do?
Thank you very much!
J.
Yes, you can do it.
Same-security-traffic command traffic to enter and leave the interface even when used with the
keyword intra-interface, that allows the VPN support has spoke-to-spoke.
Here are a few examples.
http://www.Cisco.com/en/us/products/ps6120/prod_configuration_examples_list.html
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00807f9a89.shtml
PIX / ASA 7.X: Add a new Tunnel or remote access to an existing L2L VPN
PIX / ASA 7.x enhanced has spoken-to-Client VPN with the example of setting up authentication GANYMEDE +.
-
Cannot ping between virtual servers on the same host
I have a 5 ESXi host with 3 virtual copies of Windows Server 2008R2 running on them. The ESXi host is connected to my switch, which has the Windows 2008 R2 DC to my test network and my laptop management with VSphere branch above as well. I can ping host, mobile and ad server of each of the individual virtual servers and can ping and RDP for all 3 from other devices not on that host, but I cannot communicate between the three. I have Windows Firewall disabled on all three. I have no firewall, and all machines have an IP address in the 10.0.0.X range I deleted then recreated the only virtual switch on the host on which appear all 3. I've been VERY frustrated for the last 3 days on it. Why my virtual machine cannot talk to each other?
When you have registered virtual machines in ESX you selected moved VM or Coiped VM? Go to editing parameters and watch the MAC addresses. My guess is that if you copied power (including the vmx files) then the MAC address is the same for all virtual machines. You can stop the machine and change for a MAC address mac address. You can also remove the network adapters, one of each, and then add the new network cards. Remember to reconfigure the IP addresses on the box and remove the ghost network maps after doing this.
Check this KB to change the mac address.
http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=507
Also, can you connect to the switch and look at the ARP table and see if the system VMs register here.
-
Instances of VMware cannot ping between them somehow...
This is the environment for my experience:
Host: My Windows XP sp3
Products VMware: Vmware Workstation 6.0.3
Instances of VMware: one is installed Win2k3 with SP2 and a domain controller/DNS/Exchange server role, another is installed Win XP sp3 and play as a customer...
IP of the domain controller configuration:
Windows IP configuration
Name of the host...: dc
Suffix main Dns...: ge.com
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.
... DNS suffix search list: ge.com
Ethernet connection to the Local card:
The connection-specific DNS suffix. :
... Description: VMware accelerated AMD PCNet Adapter
Physical address.... : 00-0C-29-56-FD-24
DHCP active...: No.
... The IP address: 192.168.238.3
... Subnet mask: 255.255.255.0.
... Default gateway. :
DNS servers...: 192.168.238.3.
Configuration of the client IP as below:
*********************************************************
Windows IP configuration
Name of the host...: client1
Suffix main Dns...: ge.com
... Node type: unknown
Active... IP routing: No.
Active... proxy WINS: No.
... DNS suffix search list: ge.com
Ethernet connection to the Local card:
The connection-specific DNS suffix. :
... Description: VMware accelerated AMD PCNet Adapter
Physical address.... : 00-0C-29-54-9D-B4
DHCP active...: No.
... The IP address: 192.168.238.4
... Subnet mask: 255.255.255.0.
... Default gateway. :
DNS servers...: 192.168.238.3.
And here are the parameters of the DC on Vmware:
And here's the VMware client settings:
And settings of network virtual as below:
My problem is:
Today, two Merethe cannot ping each other all at ONCE, even if they worked very well without any problems.
I tried to change the other IPs/remove and add maps network/restart on two instances but still no luck
Please kindly help me friends :)
Hmm so there is no problem with the NAT adapter, problem looks to with Bridge mode... Check if proceeding under in the cardiac control panels network connections is enabled for all vmware... cards try to disable and enable them
If its possible to restart the virtual machine... try this
-Remove the network card
-Turn on the virtual computer.
-Turning off the virtual computer.
-Add the network adapter
-Start the virtual machine. See if that helps.
Concerning
Anil
Save the planet, go for green
If you have found my reply to be useful, feel free to mark it as useful or Correct.
-
Ping of ASA to remote VPN site
I am haivng a weird question. I have two ASA in place with a VPN tunnel from site to site between the two. The traffic is through the tunnel without problem. I have a whole allowed for the two locations on the tunenl IP. The issue I'm having is that when I'm on the ASAs I'm not able to ping what anyone at the remote location. PC between locations communicates very well via the VPN tunnel however.
The reason that I need is to have the ASAs information to syslog for my syslog server appliances. Y at - it something that I'm missing that will allow the ASA contact materials at the remote location?
When you try to ping, do you "ping inside?
Also, your custom logging, haven't you set up "logging inside the host"?
Maybe you are looking for
-
White screen but still can open the e-mail and work with.
Where e-mail is supposed to appear to the right, that it is not. Email is there and I can see on the lower right screen and I can open it and use it but cannot display in the blink of an eye. And, making it very difficult to work with.
-
laptop does not start at the operating system hp mini 1154nr
Hi all Can I please help determine if my hard drive is bad or is there something I can do to fix this? The problem im having is that my computer hp laptop mini 1154nr at startup hp scren with f9 and f10 display on screen. I press f10 and then exit th
-
Does not print even after replacing the cartridges refilled with geniune ones.
HP Officejet 8600 more all-in-one. Win 7 and 8.1 We recently had some inkjet cartridges recharged at the shop [personal information deleted]Overland Park Kansas. They worked for a few days then our printer started to show error messages. Since then,
-
Dell tech told me that the reason for my screen was sgretched was a bad reader video-how can I fix? I deleted ALL my drivers monitor now
-
I have the Pixma 8720. Can I still print grayscale photos.
When one of the cartridges 3 color runs out of ink, I'll still be able to print text/pictures without having to replace the empty cartridge?