Cannot access remote VPN site-to-site VPN

Similar Questions

• AnyConnectVPN users cannot access remote vpn site-to-site

  Hello-

  We have two 5510 s ASA one in 8.4 (4) and the other to 8.2 (5) in a site to site VPN configuration. All internal traffic is working smoothly.

  A: site/subnet 192.160.0.0 - local (8.4 (4)) Site/subnet b: 192.260.0.0 - distance (8.2 (5)) VPN users: 192.160.40.0 - assigned by ASA

  When you VPN into the network, all the hits of traffic A Site and everything on the subnet A is accessible.

  However, the site B is totally inaccessible to users of VPN. All computers on subnet B, the firewall itself, etc. is not reachable by ping or otherwise.

  There are also some NAT rules weird that I'm not happy with that were created after that I upgraded the Site to ASA to 8.4

  A resident of the site: external 192.160.x.x: 55.55.555.201(main)/202(mail)

  Site B (in addition to site to site) is external 192.260.x.x: 66.66.666.54 (all)

  I've pretty much just the basic rules of the NAT for VPN, Email, Internet and site to site.

  What I need to add for the VPN access to the network from site to site?

  Here is my config NAT:

  NAT (inside, outside) static source DOMAIN_LOCAL DOMAIN_LOCAL VPN_Network VPN_Network non-proxy-arp-search of route static destination

  NAT (inside, outside) static source DOMAIN_LOCAL DOMAIN_LOCAL DOMAIN_REMOTE DOMAIN_REMOTE non-proxy-arp-search of route static destination

  !

  network of the DMZ_Network object

  dynamic NAT interface (DMZ, outside)

  network of the DOMAIN_LOCAL object

  NAT dynamic interface (indoor, outdoor)

  network of the EXCHANGE_Exchange object

  NAT static Outside_Mail (any, any)

  network of the DOMAINCTRL_DHCP object

  NAT (inside, outside) interface static tcp ftp ftp service

  Thank you very much in advance and I hope that I've been pretty thorough.

  Let me know if you need anything that anyone else. Thank you!!

  Theo,

  You don't need the NAT rules outside (depending on your configuration).

  Basically, you need to add the pool VPN L2L traffic and network remote to the ACL of split tunneling (if configured), also the "permit same-security-traffic intra-interface".

  Please let me know.

  Thank you.

• 2 VPN SITE to SITE with ACCESS REMOTE VPN

  Hello

  I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

  Concerning

  Thus, on the routers will be:

  

  Cisco 2611:

  LAN: 10.10.10.0/24

  access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255
  

  access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

  !

  10 ipsec-isakmp crypto map clientmap

  defined by peer 172.18.124.199

  match address 100

  !

  IP local pool ippool 14.1.1.1 14.1.1.254

  !

  access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255
  

  access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE
  

  !

  crypto ISAKMP client configuration group ra-customer
  

      pool ippool

  ACL 120

  !

  Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

  HTH,

  Portu.

• Cannot access a Web site using Java Script

  Cannot access a Web site using Java Script. I'm not sure what it blocks I use Win 7, Avast free, AntimalwareBytes.
  I get a pop up window with
  Name: mcs
  Location: http://myspeedtest02.windstream.net  
  say "application blocked by security settings, blocking the untrusted application.
  I don't know what it blocks, but suspect it is related to the security of Windows.
  I think that the Java Applet is blocked, but I would like to run this test of speed from my ISP.  I tried to access the website of Google Chrome and IE, with the same result. Nobody knows what this block and how to unlock it?

  This is actually not JavaScript, it's Java.  Despite the name, they are really very very different.

  Java itself can be dangerous, especially if it is not a trusted application.  It is my sincere recommendation that you do not continue.

  If you want anyway, you can go into your control panel, open the Java settings and set it to allow untrusted applications.

• VPN clients cannot access remote sites - PIX, routing problem?

  I have a problem with routing to remote from our company websites when users connect via their VPN client remotely (i.e. for home workers)

  Our headquarters contains a PIX 515E firewall. A number of remote sites to connect (via ADSL) to head office using IPSEC tunnels, ending the PIX.

  Behind the PIX is a router 7206 with connections to the seat of LANs and connections to a number of ISDN connected remote sites. The default route on 7206 points to the PIX from traffic firewall which sits to ADSL connected remote sites through the PIX. Internal traffic for LAN and ISDN connected sites is done via the 7206.

  Very good and works very well.

  When a user connects remotely using their VPN client (connection is interrupted on the PIX) so that they get an IP address from the pool configured on the PIX and they can access resources located on local networks to the office with no problems.

  However, the problem arises when a remote user wants access to a server located in one of the remote sites ADSL connected - it is impossible to access all these sites.

  On the remote site routers, I configured the access lists to allow access from the pool of IP addresses used by the PIX. But it made no difference. I think that the problem may be the routes configured on the PIX itself, but I don't know what is necessary to solve this problem.

  Does anyone have suggestions on what needs to be done to allow access to remote sites for users connected remotely via VPN?

  (Note: I suggested a workaround, users can use a server on LAN headquarters as a "jump point" to connect to remote servers from there)

  with pix v6, no traffic is allowed to redirect to the same interface.

  for example, a remote user initiates an rdp session for one of the barns adsl. PIX decrypts the packet coming from the external interface and looks at the destination. because the destination is one of adsl sites, pix will have to return traffic to the external interface. Unfortunately, pix v6.x has a limitation that would force the pix to drop the packet.

  with the v7, this restriction has been removed with the "same-security-traffic control intra-interface permits".

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml

• Remote VPN users cannot access tunnel from site to site

  Cisco ASA5505.

  I have a tunnel of site-to-site set up from our office to our Amazon AWS VPC.  I'm not a network engineer and have spent way too much time just to get to this point.

  It works very well since within the office, but users remote VPN can not access the tunnel from site to site.  All other remote access looks very good.

  The current configuration is here: https://gist.github.com/pmac72/f483ea8c7c8c8c254626

  Any help or advice would be greatly appreciated.  It is probably super simple for someone who knows what they're doing to see the question.

  Hi Paul.

  Looking at your configuration:

  Remote access:

  internal RA_GROUP group policy
  RA_GROUP group policy attributes
  value of server DNS 8.8.8.8 8.8.4.4
  Protocol-tunnel-VPN IPSec
  value of Split-tunnel-network-list Split_Tunnel_List

  permit same-security-traffic intra-interface
   
  type tunnel-group RA_GROUP remote access
  attributes global-tunnel-group RA_GROUP
  address RA_VPN_POOL pool
  Group Policy - by default-RA_GROUP
  IPSec-attributes tunnel-group RA_GROUP
  pre-shared key *.
   
  local pool RA_VPN_POOL 10.0.0.10 - 255.255.255.0 IP 10.0.0.50 mask

  Site to site:

  card crypto outside_map 1 match address acl-amzn
  card crypto outside_map 1 set pfs
  peer set card crypto outside_map 1 AWS_TUNNEL_1_IP AWS_TUNNEL_2_IP
  card crypto outside_map 1 set of transformation transformation-amzn
   
   
  I recommend you to use a local IP address pool with a different IP address that deals with the inside interface uses, now you are missing NAT are removed from the IP local pool to the destination of the site to site:
   
  NAT_EXEMPT list of ip 10.0.0.0 access allow 255.255.255.0 172.17.0.0 255.255.0.0
   
  NAT (outside) 0-list of access NAT_EXEMPT
   
  Now, there's a dynamically a NAT exempt allowing traffic to go out and are not translated.
   
  I would like to know how it works!
   
  Please don't forget to rate and score as correct the helpful post!
   
  Kind regards
   
  David Castro,
   
   

• Cannot access remote network by VPN Site to Site ASA

  Hello everyone

  First of all I must say that I have configured the VPN site-to site a million times before.  Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

  ASA local:
  hostname gyd - asa
  domain bct.az
  activate the encrypted password of XeY1QWHKPK75Y48j
  XeY1QWHKPK75Y48j encrypted passwd
  names of
  DNS-guard
  !
  interface GigabitEthernet0/0
  Shutdown
  nameif vpnswc
  security-level 0
  IP 10.254.17.41 255.255.255.248
  !
  interface GigabitEthernet0/1
  Vpn-turan-Baku description
  nameif outside Baku
  security-level 0
  IP 10.254.17.9 255.255.255.248
  !
  interface GigabitEthernet0/2
  Vpn-ganja description
  nameif outside-Ganja
  security-level 0
  IP 10.254.17.17 255.255.255.248
  !
  interface GigabitEthernet0/2.30
  Description remote access
  VLAN 30
  nameif remote access
  security-level 0
  IP 85.*. *. * 255.255.255.0
  !
  interface GigabitEthernet0/3
  Description BCT_Inside
  nameif inside-Bct
  security-level 100
  IP 10.40.50.65 255.255.255.252
  !
  interface Management0/0
  nameif management
  security-level 100
  IP 192.168.251.1 255.255.255.0
  management only
  !
  boot system Disk0: / asa823 - k8.bin
  passive FTP mode
  DNS server-group DefaultDNS
  name-server 192.168.1.3
  domain bct.az
  permit same-security-traffic intra-interface
  object-group network obj - 192.168.121.0
  object-group network obj - 10.40.60.0
  object-group network obj - 10.40.50.0
  object-group network obj - 192.168.0.0
  object-group network obj - 172.26.0.0
  object-group network obj - 10.254.17.0
  object-group network obj - 192.168.122.0
  object-group service obj-tcp-eq-22
  object-group network obj - 10.254.17.18
  object-group network obj - 10.254.17.10
  object-group network obj - 10.254.17.26
  access-list 110 scope ip allow a whole
  NAT list extended access permit tcp any host 10.254.17.10 eq ssh
  NAT list extended access permit tcp any host 10.254.17.26 eq ssh
  access-list extended ip allowed any one sheep
  icmp_inside list extended access permit icmp any one
  icmp_inside of access allowed any ip an extended list
  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
  RDP list extended access permit tcp any host 192.168.45.3 eq 3389
  rdp extended permitted any one ip access list
  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
  NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
  NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
  NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
  access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
  access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
  access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
  access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
  access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
  GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
  Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
  azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
  permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
  permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
  pager lines 24
  Enable logging
  emblem of logging
  recording of debug console
  recording of debug trap
  asdm of logging of information
  Interior-Bct 192.168.1.27 host connection
  flow-export destination inside-Bct 192.168.1.27 9996
  vpnswc MTU 1500
  outside Baku MTU 1500
  outside-Ganja MTU 1500
  MTU 1500 remote access
  Interior-Bct MTU 1500
  management of MTU 1500
  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
  IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any outside Baku
  ICMP allow access remotely
  ICMP allow any interior-Bct
  ASDM image disk0: / asdm - 621.bin
  don't allow no asdm history
  ARP timeout 14400
  global (outside-Baku) 1 interface
  global (outside-Ganja) interface 2
  3 overall (RAS) interface
  azans access-list NAT 3 (outside-Ganja)
  NAT (remote access) 0 access-list sheep-vpn-city
  NAT 3 list nat-vpn-internet access (remote access)
  NAT (inside-Bct) 0-list of access inside_nat0_outbound
  NAT (inside-Bct) 2-nat-ganja access list
  NAT (inside-Bct) 1 access list nat
  Access-group rdp on interface outside-Ganja
  !
  Router eigrp 2008
  No Auto-resume
  neighbor 10.254.17.10 interface outside Baku
  neighbor 10.40.50.66 Interior-Bct interface
  Network 10.40.50.64 255.255.255.252
  Network 10.250.25.0 255.255.255.0
  Network 10.254.17.8 255.255.255.248
  Network 10.254.17.16 255.255.255.248
  redistribute static
  !
  Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
  Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
  Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
  Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
  Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
  Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
  Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
  Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
  Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
  Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
  Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  AAA-server protocol Ganymede GANYMEDE +.
  AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
  key *.
  AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
  key *.
  RADIUS protocol AAA-server TACACS1
  AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
  key *.
  AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
  key *.
  authentication AAA ssh console LOCAL GANYMEDE
  Console to enable AAA authentication RADIUS LOCAL
  Console Telnet AAA authentication RADIUS LOCAL
  AAA accounting ssh console GANYMEDE
  Console Telnet accounting AAA GANYMEDE
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.1.0 255.255.255.0 Interior-Bct
  http 192.168.139.0 255.255.255.0 Interior-Bct
  http 192.168.0.0 255.255.255.0 Interior-Bct
  Survey community SNMP-server host inside-Bct 192.168.1.27
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
  Crypto ipsec transform-set newset aes - esp esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
  Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
  Crypto ipsec transform-set vpnclienttrans transport mode
  life crypto ipsec security association seconds 2147483646
  Crypto ipsec kilobytes of life security-association 2147483646
  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
  correspondence address card crypto mymap 10 110
  card crypto mymap 10 peers set 10.254.17.10
  card crypto mymap 10 transform-set RIGHT
  correspondence address card crypto mymap 20 110
  card crypto mymap 20 peers set 10.254.17.11
  mymap 20 transform-set myset2 crypto card
  card crypto mymap interface outside Baku
  correspondence address card crypto ganja 10 110
  10 ganja crypto map peer set 10.254.17.18
  card crypto ganja 10 transform-set RIGHT
  card crypto interface outside-Ganja ganja
  correspondence address card crypto vpntest 20 110
  peer set card crypto vpntest 20 10.250.25.1
  newset vpntest 20 transform-set card crypto
  card crypto vpntest interface vpnswc
  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
  card crypto interface for remote access vpnclientmap
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto
  name of the object CN = gyd - asa .az .bct
  sslvpnkeypair key pair
  Configure CRL
  map of crypto DefaultCertificateMap 10 ca certificate

  crypto isakmp identity address
  ISAKMP crypto enable vpnswc
  ISAKMP crypto enable outside-Baku
  ISAKMP crypto enable outside-Ganja
  crypto ISAKMP enable remote access
  ISAKMP crypto enable Interior-Bct
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  crypto ISAKMP policy 20
  preshared authentication
  aes encryption
  md5 hash
  Group 2
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 40
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 30
  No vpn-addr-assign aaa
  Telnet timeout 5
  SSH 192.168.0.0 255.255.255.0 Interior-Bct
  SSH timeout 35
  Console timeout 0
  priority queue outside Baku
  queue-limit 2046
  TX-ring-limit 254
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Server NTP 192.168.1.3
  SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
  SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
  SSL-trust ASDM_TrustPoint0 remote access point
  WebVPN
  turn on remote access
  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
  enable SVC
  tunnel-group-list activate
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
  internal group ssl policy
  attributes of group ssl policy
  banner welcome to SW value
  value of DNS-server 192.168.1.3
  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
  group-lock value SSL
  WebVPN
  value of the SPS URL-list
  internal vpn group policy
  attributes of vpn group policy
  value of DNS-server 192.168.1.3
  Protocol-tunnel-VPN IPSec l2tp ipsec
  disable the PFS
  BCT.AZ value by default-field
  ssl VPN-group-strategy
  WebVPN
  value of the SPS URL-list
  IPSec-attributes tunnel-group DefaultL2LGroup
  ISAKMP retry threshold 20 keepalive 5
  attributes global-tunnel-group DefaultRAGroup
  raccess address pool
  Group-RADIUS authentication server
  Group Policy - by default-vpn
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared key *.
  ISAKMP retry threshold 20 keepalive 5
  IPSec-attributes tunnel-group DefaultWEBVPNGroup
  ISAKMP retry threshold 20 keepalive 5
  tunnel-group 10.254.17.10 type ipsec-l2l
  IPSec-attributes tunnel-group 10.254.17.10
  pre-shared key *.
  ISAKMP retry threshold 20 keepalive 5
  type SSL tunnel-group remote access
  attributes global-group-tunnel SSL
  ssl address pool
  Authentication (remote access) LOCAL servers group
  Group Policy - by default-ssl
  certificate-use-set-name username
  Group-tunnel SSL webvpn-attributes
  enable SSL group-alias
  Group-url https://85. *. *. * / activate
  tunnel-group 10.254.17.18 type ipsec-l2l
  IPSec-attributes tunnel-group 10.254.17.18
  pre-shared key *.
  ISAKMP retry threshold 20 keepalive 5
  tunnel-group 10.254.17.11 type ipsec-l2l
  IPSec-attributes tunnel-group 10.254.17.11
  pre-shared key *.
  ISAKMP retry threshold 20 keepalive 5
  type tunnel-group DefaultSWITGroup remote access
  attributes global-tunnel-group DefaultSWITGroup
  raccess address pool
  Group-RADIUS authentication server
  Group Policy - by default-vpn
  IPSec-attributes tunnel-group DefaultSWITGroup
  pre-shared key *.
  !
  type of policy-card inspect dns migrated_dns_map_1
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the migrated_dns_map_1 dns
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect sunrpc
  inspect xdmcp
  inspect the netbios
  Review the ip options
  class flow_export_cl
  flow-export-type of event all the destination 192.168.1.27
  class class by default
  flow-export-type of event all the destination 192.168.1.27
  Policy-map Voicepolicy
  class voice
  priority
  The class data
  police release 80000000
  !
  global service-policy global_policy
  service-policy interface outside Baku Voicepolicy
  context of prompt hostname

  Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
  : end
  GYD - asa #.

  ASA remote:
  ASA Version 8.2 (3)
  !
  ciscoasa hostname
  activate the encrypted password of XeY1QWHKPK75Y48j
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  DNS-guard
  !
  interface Ethernet0/0
  nameif inside
  security-level 100
  IP 192.168.80.14 255.255.255.0
  !
  interface Ethernet0/1
  nameif outside
  security-level 0
  IP 10.254.17.11 255.255.255.248
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  nameif management
  security-level 100
  no ip address
  management only
  !
  boot system Disk0: / asa823 - k8.bin
  passive FTP mode
  access-list 110 scope ip allow a whole
  192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  management of MTU 1500
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow all outside
  ICMP allow any inside
  ASDM image disk0: / asdm - 621.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside) 0 access-list sheep
  Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.80.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
  Crypto ipsec transform-set newset aes - esp esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
  life crypto ipsec security association seconds 2147483646
  Crypto ipsec kilobytes of life security-association 2147483646
  correspondence address card crypto mymap 10 110
  card crypto mymap 10 peers set 10.254.17.9
  mymap 10 transform-set myset2 crypto card
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  crypto ISAKMP policy 20
  preshared authentication
  aes encryption
  md5 hash
  Group 2
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 40
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN

  tunnel-group 10.254.17.9 type ipsec-l2l
  IPSec-attributes tunnel-group 10.254.17.9
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns migrated_dns_map_1
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the migrated_dns_map_1 dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname

  Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
  : end
  ciscoasa # $

  Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

  Would appreciate any help. Thank you in advance...

  If the tunnel is up (phase 1), but no traffic passing the best test is the following:

  Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

  inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

  The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

  Test on both directions.

  Please post the results.

  Federico.

• AnyConnect VPN users cannot access remote subnets?

  I googled this until blue in the face without result.  I don't understand why Cisco this so difficult?  When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices.  What should I do to allow my anyconnect vpn clients access to my remote sites?

  Cisco 5510 8.4

  Hello

  What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.

  In addition to routing, you must have configured for each remote site and the VPN pool NAT0

  Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this

  object-group network to REMOTE SITES

  object-network 10.10.10.0 255.255.255.0

  object-network 10.10.20.0 255.255.255.0

  object-network 10.10.30.0 255.255.255.0

  object-network 10.10.40.0 255.255.255.0

  network of the VPN-POOL object

  10.10.224.0 subnet 255.255.255.0

  NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL

  The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.

  Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.

  My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)

  Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?

  -Jouni

• a public access remote vpn from an inside interface asa 5505

  I'm trying to see if it is possible to accomplish what I am trying. I have an ASA 5505 with the following configuration.

  1. There is an external connection, connected to the ISP. Let's say that it is 10.1.1.1/24 for ease. There is a remote VPN configuration as the access of people through this interface.

  2. There's the inside network, which is the normal LAN. It's cable system in the office. to say that it is 172.20.0.1/24.

  3. There is a wireless network on a VLAN separate called WLAN. It has an IP of 192.168.1.1/24. There is an ACL allowing traffic to that VLAN to the public internet.

  Essentially, I would like users to be able to use the same VPN settings they use when connecting from outside of the Office when you are connected to WIFI.

  Also, I would like that they can access public IP addresses that I have NAT would be to internal servers. In this way, they can use IP addresses when they use on the public internet.

  Is this possible?

  Hello

  Well that's not going to be possible, the only thing you can really do is to activate the crypto map on the WLAN facing interface, by design, you cannot not access VPN, ping or manage the device on an interface which is not directly connected to you.

  I hope this helps.

  Mike

• Cannot access https secure sites after installation of Netnanny

  Use Firefox for years. Then recently installed "net nanny" software and it has changed the security settings on Firefox.

  I can't access all the secure https sites regardless of whether net nanny software is even uninstalled.

  The following alert occurs on Firefox running...
  "Could not initialize component of application security. The most likely cause is problems with the files in the directory of the profile of your application. Please check that this directory has no restriction of read/write and your hard disk is not full or close to full. It is recommended that you exit the application and correct the problem. If you continue to use this session, you may see incorrect application behavior when you access security features. »

  Then when you try to access an https site, I get an error as follows:
  "Secure connection failed".

  An error occurred during a connection to support.mozilla.com.

  Cannot connect securely because the SSL protocol has been disabled.

  (Error code: ssl_error_ssl_disabled) »

  Use SSL 3.0 and use TLS 1.0 are both selected in the "Advanced settings"

  I also left a post on the forum of Net nanny however clearly don't have an adequate response when they talk about a setting in their software ("allow secure content") which is already activated anyway with the uninstalled software, however it still does not solve the problem. In fact, I had to use IE to post on this forum.

  It clearly provided a message when configuring the net nanny that he changed the security settings when Firefox has been executed for the first time for each user.

  I wish I had a solution so I can go back to using Firefox as my default browser and do believe a software application and a well known who, should take a non-functional browser but not another.

  Start with this support article:
  
  https://support.Mozilla.com/en-us/KB/could%20not%20initialize%20The%20browser%20security%20component

• 1920 router access remote vpn LDAP living

  Hello

  What is required for a router in 1920 use AnyConnect and/or also integrate with AD LDAP?

  Currently, this router supports legacy clients and has these licenses:

  Technology for the Module package license information: "c1900".

  -----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  ------------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  Security securityk9 Permanent securityk9
  given none none none

  The vpn to access remote client inherited integrate with AD LDAP?

  Thank you.

  As long as you are on IOS 15.3.3M3 or better, you have all the licenses you need for 3.1 AnyConnect run on your 1921.

  The guide to directly connect your router to LDAP can be found here:

  http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_usr_ldap/configuration/15-Mt/sec-usr-LDAP-15-Mt-book/sec_conf_ldap.html

  Personally, I would avoid directly interfacing with LDAP, because it can be a complex arrangement. While it can be done, it's easier to have your router to connect to the NPS Microsoft via RADIUS server for your authentication.

• Access remote vpn fails

  Hello

  Im trying to figure out why vpn for remote access is at our company office fails. The scenario: we currently have a work situation. The way this works is that users connect to the public ip address of the DSL router and nat vpn traffic to an internal router. This router then forwards the traffic to the vpn server.

  vpn client remote <=>{{internet}} <=>cpe <=>adsl router <=>vpn server

  Now, Im implementation of a 2nd internet line with more or less the same configuration, but instead of an adsl cpe, we use a cisco router. When users need to connect even with the only difference being a different public ip address

  client remote vpn <=>{{internet}} <=>cisco <=>router <=>router, vpn server

  So, the only change in the prepective of cisco vpn clients is the host.  However when testing, it didn't work. The vpn client times out. With something like 'the vpn peer did not' do not remember the exact error by heart. Now logic tells me that because he now works in the part between the internal router and the vpn gateway is ok. My guess is it's because of the cisco access list. I had my own list of access, but for some reason, I decided to use firewall SDM Wizard configuration and it generated this access list.

  Expand the IP 100 access list

  10 permit tcp any host 90.90.150.82 eq 4500

  20 permit tcp any host 90.90.150.82 eq 500

  30 permit tcp any host 90.90.150.82 eq 51

  40 permit tcp any host 90.90.150.82 eq 50

  50 permit tcp any host 90.90.150.82 eq 3101

  60 permit tcp any host 90.90.150.82 eq 993

  70 permit tcp any host 90.90.150.82 eq 587

  80 permit tcp any host 90.90.150.82 eq smtp (722 matches)

  90 deny ip 192.168.0.8 0.0.0.7 (20606 matches)

  100 permit icmp any host 90.90.150.82 - response to echo (113 matches)

  110 permit icmp any host 90.90.150.82 time exceeded (54 matches)

  120 permit icmp any inaccessible 90.90.150.82 host (1051 matches)

  130 deny ip 10.0.0.0 0.255.255.255 (726 matches)

  140 deny ip 172.16.0.0 0.15.255.255 all

  150 deny ip 192.168.0.0 0.0.255.255 everything

  160 deny ip 127.0.0.0 0.255.255.255 everything

  170 deny ip 255.255.255.255 host everything

  180 deny host ip 0.0.0.0 everything

  190 deny ip any any newspaper (5163 matches) Extended 100 IP access list

  Given that the natting to the smtp protocol works, I think that the natting is ok. I ping the server vpn, so routing also seems to be ok. Vpn users receive a vpn ip address pool 192.168.x.x. is it possible that the 150 rule that prevents them to connect? I can't test, because it's a living environment and I'll have to plan a window. Im just trying to figure out what is wrong, so I can fix it for a window. Someone at - it ideas?

  No, you don't need AH if your VPN policy does not include AH.

• Access remote VPN question - hairpin

  Hello, I did a search before posting this question but I have not found anything specific to my situation.

  We have our ASA5520 configured in our main office to allow remote access Cisco VPN client users to access our network.  We have a (network 192.168.1.0/24) remote desktop we have a configured on the same ASA5520 VPN IPSec tunnel that allows the use of internal users (in the main office) to access resources on the network remote (192.168.1.0) and vice versa.  The problem is that when users connect to the remote VPN access, they are not able to access the resources of the remote office network.  We created the nat0 ACL and labour, and split tunnel routing is implemented for users VPN remote network access (if I make a copy of the route on my laptop after connecting to the VPN, I see the road to 192.168.0.0/24 in my routing table).  Routing everything is in place to do this, since the IPSec VPN tunnel is up and working.  My suspicion is that the question has something to do with the consolidation of these VPN clients.

  What else needs to be configured to work?  Thank you.

  Hi Scott,.

  I have a client with a PIX 515E which allows connections to remote VPN and VPN LAN2LAN multiple connections.

  We had this problem too... so what I made in my pix was:

  TEST (config) # same-security-traffic intra-interface permits (its off by default)

  If you use ASDM go to:

  Configuration > Interfaces >

  at the bottom of this page, there is an option that says: 'enable traffic between two or more host computers connected to the same interface '.

  Check and it should work... I hope

  I await your comments...

  Kind regards.

  Joao Tendeiro

• Web searches are redirected to OpenDNS. Cannot access these Web sites.

  This problem just started. Whenever I try to load a page (in this case Gamefaqs), I get redirected to this search engine called openDNS, saying that the site is not available. It has a link to the site, and whenever I clicked, it redirects me to this thing OpenDNS.

  I tried loading the page with the default browser of chrome on this phone, but also my laptop using firefox and chrome and have not experienced this problem. Yet the problem persists when you try to access the mobile site through firefox.

  I have tried clearing the cache, uninstall and reinstalling, yet the problem isn't resolved. I have done a virus scan, thinking it might be some form of malware that is hijacking my search engine. That all comes back clean.
  

  I've never heard of OpenDNS, nor have I allowed it to become my search engine. When I go into the settings of search engine, it does not appear, but he manages to keep hijacking of my searches on google and redirect me sites that work normally.

  Please help me.

  Hi SuperRup91, I was able to reproduce this problem on Firefox Mobile on a wi - fi network using OpenDNS. Queries for a single word for non-existent domains + by pressing the arrow go back a page of results of OpenDNS. Typing a search suggestion next to the icon of Google for the word, or by using a query of several given word of Google results. Unless you can change to a different DNS provider, I think you may be stuck with these options.

• Split tunneling cannot access remote host

  Hi guys,.

  Having this problem by which I am able to connect the Anyconnect client but unable to ping / access of remote servers. See below for the config of the SAA;

  Any ideas would be a great help, thank you!

  ASA Version 9.1 (1)

  !

  ASA host name

  enable the encrypted password xxxxxxx

  xxxxxxxxxxxxx encrypted passwd

  names of

  mask of local pool AnyPool 10.0.0.1 - 10.0.0.10 IP 255.255.255.0

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP address 203.106.x.x 255.255.255.224

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 99

  IP 172.19.88.254 255.255.255.0

  !

  interface Management0/0

  management only

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  passive FTP mode

  clock timezone 8 MYT

  the SVR object network

  Home 172.19.88.11

  e-mail server in description

  network of the NETWORK_OBJ_172.19.88.0_24 object

  172.19.88.0 subnet 255.255.255.0

  network of the VPN-POOL object

  10.0.0.0 subnet 255.255.255.0

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group service DM_INLINE_SERVICE_0

  ICMP service object

  area of service-purpose tcp - udp destination eq

  the destination hostname eq tcp service object

  the purpose of the tcp destination eq https service

  the purpose of the tcp destination eq imap4 service

  the purpose of the tcp destination eq nntp service

  the purpose of the tcp destination eq pop3 service

  the purpose of the tcp destination eq smtp service

  the purpose of the tcp destination eq telnet service

  Outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_0 any object SVR

  Outside_access_in list extended access allow TCPUDP of object-group a

  Outside_access_in access-list extended ip any any idle state to allow

  Internal_access_in list extended access allow TCPUDP of object-group a

  Internal_access_in access-list extended ip any any idle state to allow

  SPLIT_TUNNEL list standard access allowed 10.0.0.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  exploitation forest-size of the buffer 16384

  buffered logging critical

  asdm of logging of information

  Debugging trace record

  exploitation forest flash-bufferwrap

  record level of the rate-limit 1000 1 2

  management of MTU 1500

  MTU 1500 internal

  Outside 1500 MTU

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 711.bin

  don't allow no asdm history

  ARP timeout 14400

  no permit-nonconnected arp

  !

  the SVR object network

  203.106.x.x static NAT (indoor, outdoor)

  !

  source of auto after the cessation of NAT (inside, outside) dynamic interface

  Internal_access_in in interface internal access-group

  Access-group Outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 203.106.23.97 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  Enable http server

  http 192.168.1.0 255.255.255.0 management

  http authentication certificate management

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  No vpn sysopt connection permit

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec pmtu aging infinite - the security association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  Outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = ASA

  Configure CRL

  Crypto ca trustpoint Anyconnect_TrustPoint

  registration auto

  name of the object CN = ASA

  anyconnect_rsa key pair

  Configure CRL

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  trustpool crypto ca policy

  string encryption ca Anyconnect_TrustPoint certificates

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint Anyconnect_TrustPoint

  Telnet timeout 3

  SSH 172.19.88.0 255.255.255.0 internal

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  Console timeout 0

  management of 192.168.1.100 - 192.168.1.200 addresses dhcpd

  enable dhcpd management

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP server 119.110.97.148 prefer external source

  SSL-trust outside Anyconnect_TrustPoint point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3

  AnyConnect profiles AnyConnect_client_profile disk0: / AnyConnect_client_profile.xml

  AnyConnect enable

  attributes of Group Policy DfltGrpPolicy

  VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list SPLIT_TUNNEL

  Group Policy 'GroupPolicy AnyConnect' internal

  Group Policy attributes "GroupPolicy AnyConnect"

  value of server WINS 172.19.88.11

  value of server DNS 172.19.88.11

  SSL VPN-tunnel-Protocol ikev2 client ssl clientless

  WebVPN

  AnyConnect value AnyConnect_client_profile type user profiles

  attributes global-tunnel-group DefaultWEBVPNGroup

  address pool AnyPool

  tunnel-group "AnyConnect" type remote access

  attributes global-tunnel-group "AnyConnect".

  address pool AnyPool

  strategy-group-by default "GroupPolicy AnyConnect"

  tunnel-group "AnyConnect" webvpn-attributes

  Group-alias "AnyConnect" activate

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  Hi Max,.

  Please send me the output of 'see the anyconnect vpn-sessiondb' once connected with VPN.

  And try to add the following configuration and see if that helps:

  NAT (inside, outside) 1 static source NETWORK_OBJ_172.19.88.0_24 NETWORK_OBJ_172.19.88.0_24 static destination VPN-VPN-POOL no-proxy-arp-route search

  And one more qusetion do you use split tunnel? If yes then you must make the following changes, because your split tunnel is incorrect, in the split tunnel, you have configured the address pool of vpn. Please make the following change:

  no access list SPLIT_TUNNEL standards not allowed 10.0.0.0 255.255.255.0

  Standard access list SPLIT_TUNNEL allow 172.19.88.0 255.255.255.0

  Group Policy attributes "GroupPolicy AnyConnect"

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list SPLIT_TUNNEL

  Let me know if this can help, or if you have any questions, more about it.

  Thank you

  Jeet Kumar