Cannot resolve a reference multiname unambiguously OSMF build from scratch

Similar Questions

• Problem building from scratch data acquisition program

  Hi all

  I know that this may be a question trivial moment, but I can't find previous messages explaining my problem... I want to go round in circles

  I am trying to build a system with an analog input and digital output (I use the cDAQ 9172 with NI 9215 ADC and NI 9403 DIO) and I try not not to use the DAQ Assistant.

  But when I run the VI the list updated very slowly even with a delay loop of 1 ms and a sampling rate of 1000 and 100 samples read.

  I tried to insert a chart, but which shows nothing at all

  And based on my sampling rate (FS higher, faster the error pops up) I get an error saying that the samples I'm reading is not available more.

  I understand that something is taking too much time in my loop, but I don't see what it should be.

  Is it possible to configure this daqmx to taste at the request?

  The analogue output to / digital is part of a motor controller I am trying to build, where the analog input is feedback from motor position of a potentiometer and the

  Digital pulses are a PWM signal to a hardware engine controller.

  The program runs on a Lenovo T410 with 2, 66 GHz I7 cpu, 4 GB memory, Windows 7 and LabVIEW 2009 SP1

  Sorry if this is a double post!

  Kind regards

  Tommy

  Hi Tommy,.

  In fact, I think that one of the biggest problems is that you restart your digital task inside the loop every time.  Attached is the revised for you to try code, the loop now looks like the following:

  

  Notice the DAQmx beginning is now called before entering the loop for the digital task.  Rather than use a wait function, you can use the samples of reading parameter so that the ratio of samples to read / sampling frequency is equal to the length of the loop you want (DAQmx Read blocks until the appropriate number of samples have been received).  I also put the two tasks at the same time, so you can now write digital data while the DAQmx Read waits for the desired number of samples.

  Devices of simulations are often useful, but trying to compare the performance it is always better to have the actual hardware.  USB has particularly high latency 1 time of loop ms unfortunately probably not going to be achievable, but accurate performance will be dependent on the system.  Try to run this code and see what results you can get - if you always replace the samples then you will need to increase the number of samples read by loop (and therefore decrease the rate of loop).

  I hope this helps, don't forget to let us know if you have any questions.

  Best regards

• Building from scratch pad...

  I'm a student working on my final project (just passed my first exam DRESSED!)

  I'm trying to use a Boolean array to generate a 4-digit password. So far, I am able to get the correct number appears, but I want to eliminate the value by defect-1 for no entry. I'll have to run continuously because of this repeated - 1, which is defeated the point of diabling/activation of the alarm. Finally, I want to concatenate the four numbers and compare it to a constant of arm/disarm. This VI will be added to another VI w / Council NI Elvis w / several emitter-detector sets, I have works great. I would like to add this feature to improve this one.

  Can anyone help?

  Here's what I have so far:

  Hello

  It is the best way to do it. Create events for the buttons and use a case to verify - 1... Check the attached vi. It takes a length of 5 characters entry password... After that, it stops...

  Kind regards

  Amine31

  (Kudos are always welcome, mark it as a solution if it is the only)

• Error: Cannot resolve a multiname unambiguous reference. MX. RPC.http.MXML:HTTPService

  I have this error:
  
  Cannot resolve a multiname unambiguous reference. MX. RPC.http.MXML:HTTPService
  (from C:\Program Files\Adobe\Flex 3\sdks\3.0.0\frameworks\libs\rpc.swc(mx/rpc/http/mxml/HTTPService)) Builder and (from C:\Program Files\Adobe\Flex Build
  
  I think it's maybe because I have this tag:
  
  < mx:HTTPService id = 'login_user' result = "checkLogin (event)" method = "POST" url ="' http://localhost/php/plum_tree/loginId.php ' useProxy ="false">"
  
  in the mxml file * if I take this outside and the click event code that calls checkLogin (event) there is no error.)
  
  and this tag:
  
  Import mx.rpc.http.HTTPService;
  
  in a .as file that is called from my mxml file.
  
  SEE YOU SOON

  Flex provides two classes of HTTPService in the mx.rpc.http.HTTPService and the other is mx.rpc.http.mxml.HTTPService. mx.rpc.http.mxml.HTTPService is a subclass of mx.rpc.http.HTTPService.
  Discover the language reference Flex for the differences between these two classes.

  That your code uses both HTTPService classes, there is ambiguity.
  There are two solutions to your problem. If you want to use the mx.rpc.http.HTTPService then change your code as below.
  private var gateway: HTTPService = new HTTPService();
  TO
  private var gateway:mx.rpc.http.HTTPService = new mx.rpc.http.HTTPService ();

  or
  Just use mx.rpc.http.mxml.HTTPService in both places.

  I hope this helps.

• Model error: cannot resolve macro: RegisterResolvers

  Hi all
  
  I am using RoboHelp for Word after three years and more - and feel a little rusty. I have tried to import a Word document into my project (and sometimes succeed, if the file is small enough) and then attach a custom template that is based on RoboHelp.dot. Is it possible that the custom template, I used for my project is corrupted and it is causing the problem in all the other projects that I create from scratch later? Note that it is possible to solve this problem by reinstalling the RoboHelp application software...
  
  Initializing the compiler...
  Generation of WebHelp 5.50 (13.10.606)...
  
  Model active Script error: (null) [line: 13] (null)
  Model error: cannot resolve macro: RegisterResolvers
  
  Fatal error: cannot run macro: RegisterResolvers in the build script.
  Model error: cannot resolve macro: WH_HOME_HTM
  Model error: cannot resolve macro: WH_CSH_HTM
  Model error: cannot resolve macro: WH_CSH2_HTM
  
  WebHelp (WebHelp) was built successfully:
  C:\TEMP\garbage\test\! SSL!\WebHelp\test.htm
  
  

  Hi Peter,.

  Thanks for your quick response. It's nice to meet the resident expert! :-)

  I have the full version of RoboHelp Office X (Pro) for .NET, and it was installed with Admin rights. The application, project files and output all resident locally (on the same hard drive,) but on different drives. I need to produce a WebHelp output as a stand-alone help system (for now...).

  Yes, re-installation of the application would be solve the problem, but only until I present again of my custom template. I believe that Your ' e right - my model was the culprit. So I redefined styles in RoboHelp.dot instead and seeing me is no longer the error of the model at compile time. I also followed your advice and set the macro security in Word in the middle. Thank you. I also need to increase the amount of memory available in Word running (to import large files).

  Thank you
  Rachel.

• Cannot resolve DNS-server may be down-Windows Vista

  I'm having an intermittent and repetitive problem on my laptop, which uses Vista Home Premium.

  My internet connection will reduce and out of a few hours every few weeks.  Nothing works, not games, or msn or all browsers, including firefox, internet explorer and google chrome.  When I run "diagnose and repair", it will sometimes say there is no problem, then later say that my DNS server cannot resolve the ISP addresses, and the server may be down, and that the problem cannot be repaired automatically.  It remains down for hours to days in a row.  I have a wireless connection, which is shared with 2 other computers.  The two other ones work very well, to my knowledge.  Any ideas?  I am so frustrated with this.  :(

  Oh and if you leave any ideas (which I appreciate), please keep in mind that I'm computer illiterate... I use especially programs games/internet/Word, and the words tech-type are completely lost to me.  If the details and explanations are greatly appreciated!  Thank you!

  bittyS,
  Thank you for visiting the Microsoft Answers community forum.

  It would be useful to know a few more things.  What type of router you have which is shared by all the computers on your network?  What type of Internet connection you have - is - this cable, DSL, satellite, etc. ?  Who is your Internet service provider?  Other computers never have a problem with connection to the Internet at all?  When your computer loses its Internet connection, have you tried to reboot to see if it will come back and log in?  Have you tried to reboot the router (which is made by disconnecting the power, wait 30 seconds and reconnect).

  I would recommend that you update the driver for your wireless interface card, it seems that it does not provide the connection and this could be a driver problem.  Here's how:
  1. open network connections by clicking the Start button, clicking Control Panel, clicking Network and Internet, click Network and sharing Center then click on manage network connections.
   
  2 right click on the wireless network adapter and then click on configure, then click driver then put to update driver.  Make sure that you have downloaded the latest driver from your manufacturer and loans.

  This information should be helfpful and is easy to understand the following terms:
  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx#ESEAE

  Let us know if this solves your problem, or if you need additional assistance.
  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Angular 2 http.get () fails with "cannot resolve the host name.

  I am trying to get 2 angular (well, ionic 2 actually, but the call failure is part of the kinetic moment) to shoot some json from the web. My code works fine on iOS or Android (via Cordova), but fails on any call http.get () on 10 of BlackBerry. Initially, I had problems because I did not in the whitelist the URL I was trying to download, but after whitelisting now runs the get call, but always fails. The error message "cannot resolve the host name.

  Does anyone have an idea why angular is unable to resolve an external host name when running on BlackBerry 10?

  Never mind... my bad. I encounter this problem when running my Ionic/angular application on a simulator. For me to get always consistent on many simulators BB10 different IP addresses I've run, rather than to allow VMware Player feeding the DHCP server (because it does no reservations of IP), I run a TinyCore Linux server on the same virtual network as simulators, just so that I can use DHCP on the instance of TinyCore instead Allowing no reserves. Unfortunately, I did not complete the configuration of TinyCore properly so nothing on the virtual network becomes a valid gateway or the DNS server list to access the outside world.

  When I run my application on my Z10 physics, it works fine.

• TTIMDB connection problems: cannot resolve a non optional application descriptor property [DSN]

  Hello

  We currently have the plugin TTIMDB 11 g deployed in our instance of EM10g without a problem and you want to migrate to 12 c.  Us have deployed/installed the 12.1.0.2.0 plugin in our instance of EM12c and it deployed to the agent of the 12cR3 on our dev TTIMDB server.

  When you add the target TTIMDB in the same way that it is deployed in 10g, fine tested connecting to the DB, however the target shows down with the following errors...

  1. supervised > all measures, we get this... "The TimesTen database is declining: [name of the source/db data] is not loaded '

  2. under the target Configuration > Monithat test us the connection and if Configuration connection test when fTSRI Configure the plugin has worked it is now failing... "
  Response; Cannot resolve a non optional application descriptor property [DSN] (DSN).

  
  

  Any thoughts on what may cause these errors?

  
  

  Thank you

  Steve

  
  
  

  Hi Steve,.

  We are talking about the same thing. When I check to see if the TimesTen database is loaded into memory, I mean make sure that the database is running.

  By default, a TimesTen database is loaded into memory (start) during the first connection to the database. When the last connection to database stops, it will automatically unload the database of memory (close).

  As it is recommended to change this database startup behavior by manually changing the setting of strategy of the RAM .

  That is right I've proposed a ttIsql to connect to the database during the EM test. This will ensure that the target database is in place and running, so EM can connect to it.

  If you can stay connected to the database target using ttIsql and EM reports again that the database is down, then Yes, there is another problem.

  I suggest recreating the target and try again.

  Simon

• ORA-ORA/16724-16783: cannot resolve the discrepancy

  Primary database: cluster 2 node rac, 11.2.0.2 RDBMS and GI
  Standby Database: single instance 11.2.0.2
  OPERATING SYSTEM: AIX 7.1
  
  Hello, I'm in the middle of implementing a data protection system and see a 16783 and a 16724. The system is told that it cannot resolve a gap. I made this request to search for sequences of archives that have been necessary: select * from v$ archive_gap. missing 2 stock footage. I restored both of them to the main system. 1 sequence has been recovered automatically by the system of data protection, the other has not been the case. I manually copied the archive log which was not recovered automatically in the rescue system. When I run the select * from v$ archive_gap now, no row is returned. All archive logs files that are currently in the directory Archives of primary system were copied on the standby system.
  
  Please let me know if anyone has an idea where the problem may be.
  
  Thank you

  Hello again;

  Active replication can be an option, the main concern is the load will be placed on the network and source host during this process.

  In theory, you can set the "channel of RATE setting" in RMAN to control this:

  http://docs.Oracle.com/CD/E11882_01/backup.112/e10642/rcmtunin.htm#BABDCEHG

  Best regards

  mseberg

• get the program cannot start because mfc 110u.dll is missing from the computer.

  Hello, get the program cannot start because mfc 110u.dll is missing from the computer. Try reinstalling the program to fix this problem.  Thank you

  Hi Dennis,

  Thanks for the reply.

  This error code is related to the AVG program or utility system AVG and you can try to uninstall and reinstall the program, and check if it helps.

  For more information on this you problem refer to the AVG form:

  http://www.Avg.com/us-en/AVG-forums?sec=thread&Act=show&ID=149672

  WARNING OF THIRD PARTY

  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  When you disable Antivirus:

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• I have an account but cannot modify/use the tools.  I went from computers a week ago.  Help, please.

  I have an account but cannot modify/use the tools.  I went from computers a week ago.  Help, please.

  It should not, but you will need to download the right software to use. Adobe Acrobat Reader is what you are currently using. This is why you don't have the tools you are used to.

  Adobe Acrobat (not Reader), that's what you signed up for. He has the tools, you need and are a completely different, even if application you may have initially subscribed by using Adobe Acrobat Reader.

• I am installing a purchased copy of Lightroom 6.  Cannot install because it says I have another installer works.  I don't.  I restarted from scratch.  I'm on Windows 8 on a PC.

  I am installing a purchased copy of Lightroom 6.  Cannot install because it says I have another installer works.  I don't.  I restarted from scratch.  I'm on Windows 8 on a PC.

  This error indicates that the Windows Installer Service is being used for another installation or update at this time. Alongside the installation of another program, updates Windows can also occupy the Windows Installer service and must therefore fill before you run another installation.

  However, if a previous installation failed and no not close properly, you can complete the Windows Installer process manually:

  1. Open the Task Manager and go to the tab "processes".
  2. Select "Show processes from all users" if it isn't already.
  3. Locate and put an end to any "MSIExec.exe" with adobe entries that see you.

  After these steps, try the installation once more.

  You can use also the problems with installing updates - Windows help

  Concerning

  Stéphane

• Help: Cannot resolve a multiname unambiguous reference.

  I get the following error in my code:

  Can not resolve a multiname reference unambiguously. mx.controls:Button (from C:\Program Files\Adobe\Adobe Flash Builder 4\sdks\4.1.0\frameworks\libs\framework.swc(mx.controls:Button)) and spark.components:Button (from C:\Program Files\Adobe\Adobe Flash Builder 4\sdks\4.1.0\frameworks\libs\spark.swc(spark.components:Button)) are available.    Resource: ArcGIS.mxml    Path: /ArcGIS/src    Location: Unknown    Type: Flex Problem

  I'm new to Flex and am trying to learn how to program. I have, however, seem to agree with Murphy as I always have a bug more. This is all just in my code when I added a routing with function of obstacles to enforcement. I narrowed down it to where I think the problem is, but I don't know how to fix it. Where I have narrowed it down to is in bold.

  <?xml version="1.0" encoding="utf-8"?>
  <s:Application xmlns:fx="http://ns.adobe.com/mxml/2009"
                 xmlns:s="library://ns.adobe.com/flex/spark"
                 xmlns:esri="http://www.esri.com/2008/ags"
                 xmlns:mx="library://ns.adobe.com/flex/mx"
                 initialize="initApp()"               
                 pageTitle="Austin Peay State University">
  
      <s:layout>
          <s:VerticalLayout paddingBottom="10"
                            paddingLeft="10"
                            paddingRight="10"
                            paddingTop="10"/>
      </s:layout>    
      
      <fx:Script>
          <![CDATA[
              import com.esri.ags.Graphic;
              import com.esri.ags.events.FindEvent;
              import com.esri.ags.geometry.Extent;
              import com.esri.ags.tasks.supportClasses.FindResult;
              import com.esri.ags.utils.GraphicUtil;            
              import com.esri.ags.geometry.MapPoint;
              import com.esri.ags.layers.TiledMapServiceLayer;
              import com.esri.ags.tools.NavigationTool;
              import com.esri.ags.FeatureSet;
              import com.esri.ags.events.MapMouseEvent;
              import com.esri.ags.events.RouteEvent;
              import com.esri.ags.symbols.CompositeSymbol;
              import com.esri.ags.symbols.TextSymbol;
              import com.esri.ags.tasks.supportClasses.RouteResult;
              
              import mx.events.FlexEvent;                
              import mx.logging.LogEventLevel;
              import mx.collections.ArrayCollection;
              import mx.controls.Alert;
              import mx.rpc.events.FaultEvent;
              
              import spark.events.IndexChangeEvent;
              
              [Bindable]private var stops:FeatureSet = new FeatureSet([]);
              [Bindable]private var barriers:FeatureSet = new FeatureSet([]);            
              [Bindable]private var selectedBtn:Button;            
              [Bindable]private var lastRoute:Graphic;
                          
              private function layerShowHandler(event:FlexEvent):void
              {
                  var tiledLayer:TiledMapServiceLayer = event.target as TiledMapServiceLayer;
                  myMap.lods = tiledLayer.tileInfo.lods;
              }
              
              private function tbb_changeHandler(event:IndexChangeEvent):void
              {
                  switch (tbb.selectedItem)
                  {
                      case "Zoom In":
                      {
                          navTool.activate(NavigationTool.ZOOM_IN);
                          break;
                      }
                      case "Zoom Out":
                      {
                          navTool.activate(NavigationTool.ZOOM_OUT);
                          break;
                      }
                      case "Pan":
                      {
                          navTool.activate(NavigationTool.PAN);
                          break;
                      }
                      default:
                      {
                          navTool.deactivate();
                          break;
                      }
                  }
              }
              
              private function doFind():void
              {
                  findTask.execute(myFindParams);
              }
              
              private function executeCompleteHandler(event:FindEvent):void
              {
                  myGraphicsLayer.clear();
                  
  //                resultSummary.text = "Found " + event.findResults.length + " results.";
                  myGraphicsLayer.symbol = sfsFind;
                  
                  var resultCount:int = event.findResults.length;
                  
                  if (resultCount == 0)
                  {
                      Alert.show("No buildings found. Please change your search.");
                  }
                  else
                  {
                      // add feature as graphic to graphics layer
                      for (var i:int = 0; i < resultCount; i++)
                      {
                          var graphic:Graphic = FindResult(event.findResults[i]).feature;
                          graphic.toolTip = event.findResults[i].foundFieldName + ": " + event.findResults[i].value;
                          myGraphicsLayer.add(graphic);
                      }
                      
                      // zoom to extent of all features
                      var graphicProvider:ArrayCollection = myGraphicsLayer.graphicProvider as ArrayCollection;
                      var graphicsExtent:Extent = GraphicUtil.getGraphicsExtent(graphicProvider.toArray());
                      myMap.extent = graphicsExtent.expand(3.1); // zoom out a little
                  }
              }
              
              private function initApp():void
              {
                  selectedBtn = addStopsBtn;
              }
              
              private function mapClickHandler(event:MapMouseEvent):void
              {
                  if (selectedBtn == addStopsBtn)
                  {
                      var stopSymbol:CompositeSymbol = new CompositeSymbol();
                      var circleSym:SimpleMarkerSymbol = new SimpleMarkerSymbol(SimpleMarkerSymbol.STYLE_CIRCLE, 20, 0x000099);
                      var textSym:TextSymbol = new TextSymbol(String(stops.features.length + 1));
                      textSym.textFormat = new TextFormat("Verdana", null, null, true);
                      textSym.color = 0xFFFFFF;
                      stopSymbol.symbols = [ circleSym, textSym ];
                      var stop:Graphic = new Graphic(event.mapPoint, stopSymbol);
                      inputsLayer.add(stop);
                      stops.features.push(stop);
                  }
                  else
                  {
                      var barrier:Graphic = new Graphic(event.mapPoint, barrierSymbol);
                      inputsLayer.add(barrier);
                      barriers.features.push(barrier);
                  }
                  
                  if (stops.features.length > 1)
                  {
                      routeTask.solve(routeParams);
                  }
              }
              
              private function solveCompleteHandler(event:RouteEvent):void
              {
                  var routeResult:RouteResult = event.routeSolveResult.routeResults[0];
                  lastRoute = routeResult.route;
                  lastRoute.toolTip = routeResult.routeName;
                  if (routeResult.route.attributes.Total_Time)
                  {
                      lastRoute.toolTip += " in " + Math.round(Number(routeResult.route.attributes.Total_Time)) + " minutes.";
                  }
              }
              
              private function faultHandler(event:FaultEvent):void
              {
                  Alert.show(event.fault.faultString + "\n\n" + event.fault.faultDetail, "Routing Error " + event.fault.faultCode);
                  // remove last stop (or both stops if only two)
                  if (stops.features.length <= 2)
                  {
                      inputsLayer.clear();
                      stops = new FeatureSet([]);
                  }
                  else
                  {
                      inputsLayer.remove(stops.features.pop());
                  }
              }            
          ]]>
      </fx:Script>
      
      <fx:Declarations>    
          <esri:Extent id="initialExtent" xmin="-9724772" ymin="4374071" xmax="-9723613" ymax="4374822">
              <esri:SpatialReference wkid="102100"/>
          </esri:Extent>
          <esri:NavigationTool id="navTool" map="{myMap}"/>
          
          <mx:TraceTarget includeCategory="true"
                          includeLevel="true"
                          includeTime="true"
                          level="{LogEventLevel.DEBUG}"/>
          
          <!-- Symbol for Find Result as Polygon -->
          <esri:SimpleFillSymbol id="sfsFind" alpha="0.7"/>
          
          <!-- Find Task -->
          <esri:FindTask id="findTask"
                         executeComplete="executeCompleteHandler(event)"
                         url="http://peaymapper.apsu.edu/arcgis/rest/services/APSU"/>
          
          <esri:FindParameters id="myFindParams"
                               contains="true"
                               layerIds="[2]"
                               outSpatialReference="{myMap.spatialReference}"
                               returnGeometry="true"
                               searchFields="[BUILDING_N]"
                               searchText="{fText.text}"/>
          <esri:RouteTask id="routeTask"
                          concurrency="last"
                          fault="faultHandler(event)"
                          requestTimeout="30"
                          showBusyCursor="true"
                          solveComplete="solveCompleteHandler(event)"
                          url="http://tasks.arcgisonline.com/ArcGIS/rest/services/NetworkAnalysis/ESRI_Route_NA/NAServer/Route"/>
          
          <esri:RouteParameters id="routeParams"
                                outSpatialReference="{myMap.spatialReference}"
                                pointBarriers="{barriers}"
                                stops="{stops}"/>
          
          <esri:SimpleMarkerSymbol id="barrierSymbol2"
                                   color="0xFF0000"
                                   size="15"
                                   style="x">
              <esri:SimpleLineSymbol width="4"/>
          </esri:SimpleMarkerSymbol>
          
          <esri:PictureMarkerSymbol id="barrierSymbol" source="http://help.arcgis.com/en/webapi/flex/samples/assets/road-closed-32x32.png"/>
          
          <esri:SimpleLineSymbol id="routeSymbol"
                                 width="5"
                                 alpha="0.6"
                                 color="0x000099"/>        
      </fx:Declarations>
      
      <mx:Panel title="Austin Peay State University" width="100%" height="100%">
          <mx:HDividedBox width="100%" height="100%">
              <mx:TabNavigator width="30%" height="100%">
                  <s:NavigatorContent label="Controls" width="100%" height="100%">
                      <mx:Accordion x="0" y="0" width="100%" height="100%">
                          <s:NavigatorContent label="Navigation" width="100%" height="100%">
                              <s:ButtonBar id="tbb" change="tbb_changeHandler(event)" x="0" y="20">
                                  <s:ArrayList>
                                      <fx:String>Zoom In</fx:String>
                                      <fx:String>Zoom Out</fx:String>
                                      <fx:String>Pan</fx:String>
                                  </s:ArrayList>
                              </s:ButtonBar>
                              <s:Button click="navTool.zoomToFullExtent()" label="Full Extent" x="183" y="40"/>    
                              <s:ButtonBar id="bb"
                                           requireSelection="true" x="0" y="0">
                                  <s:dataProvider>
                                      <s:ArrayList>
                                          <fx:String>Service</fx:String>
                                          <fx:String>Streets</fx:String>
                                          <fx:String>U.S. Topo</fx:String>
                                          <fx:String>Imagery</fx:String>
                                      </s:ArrayList>
                                  </s:dataProvider>
                              </s:ButtonBar>                            
                              <s:Button click="navTool.zoomToPrevExtent()"
                                        enabled="{!navTool.isFirstExtent}"
                                        label="Previous Extent" x="0" y="40"/>
                              <s:Button click="navTool.zoomToNextExtent()"
                                        enabled="{!navTool.isLastExtent}"
                                        label="Next Extent" x="104" y="40"/>
                          </s:NavigatorContent>
                          <s:NavigatorContent label="Routing" width="100%" height="100%">
                              <mx:Button id="addStopsBtn"
                                         click="selectedBtn = addStopsBtn"
                                         label="Add Stops"
                                         selected="{selectedBtn == addStopsBtn}" x="0" y="0"/>
                              <mx:Button id="addBarriersBtn"
                                         click="selectedBtn = addBarriersBtn"
                                         label="Add Barriers"
                                         selected="{selectedBtn == addBarriersBtn}" x="0" y="20"/>
                              <mx:Button label="Clear" x="0" y="40">
                                  <mx:click>
                                      <![CDATA[
                                      stops = new FeatureSet([]);
                                      barriers = new FeatureSet([]);
                                      lastRoute = new Graphic;
                                      inputsLayer.clear();
                                      ]]>
                                  </mx:click>
                              </mx:Button>
                          </s:NavigatorContent>                        
                      </mx:Accordion>    
                  </s:NavigatorContent>
                  <s:NavigatorContent label="Find" width="100%" height="100%">
                      <mx:HBox x="0" y="0">    
                          <s:TextInput id="fText"
                              enter="doFind()"
                              maxWidth="400"
                              text="Enter Text..."/>
                          <s:Button click="doFind()" label="Find"/>        
                      </mx:HBox>
                      <mx:DataGrid width="100%" height="40%"
                                   dataProvider="{findTask.executeLastResult}" x="0" y="31">
                          <mx:columns>
                              <mx:DataGridColumn width="70"
                                                 dataField="layerId"
                                                 headerText="Layer ID"/>
                              <mx:DataGridColumn dataField="layerName" headerText="Layer Name"/>
                              <mx:DataGridColumn dataField="foundFieldName" headerText="Field Name"/>
                              <mx:DataGridColumn dataField="value" headerText="Field Value"/>
                          </mx:columns>
                      </mx:DataGrid>
                  </s:NavigatorContent>                
                  <s:NavigatorContent label="Legend" width="100%" height="100%">
                  </s:NavigatorContent>
              </mx:TabNavigator>
              <mx:VDividedBox width="100%" height="100%">
                  <esri:Map id="myMap"
                            extent="{initialExtent}"
                            level="16" height="100%" y="439" width="100%" x="585"
                            mapClick="mapClickHandler(event)"
                            openHandCursorVisible="false">
                      <esri:ArcGISDynamicMapServiceLayer show="layerShowHandler(event)"
                                                       url="http://peaymapper.apsu.edu/arcgis/rest/services/APSU/networkwalking/MapServer"
                                                       visible="{bb.selectedIndex == 0}"/>                    
                      <esri:ArcGISDynamicMapServiceLayer show="layerShowHandler(event)"
                                                       url="http://server.arcgisonline.com/ArcGIS/rest/services/World_Street_Map/MapServer"
                                                       visible="{bb.selectedIndex == 1}"/>
                      <esri:ArcGISDynamicMapServiceLayer show="layerShowHandler(event)"
                                                       url="http://server.arcgisonline.com/ArcGIS/rest/services/USA_Topo_Maps/MapServer"
                                                       visible="{bb.selectedIndex == 2}"/>
                      <esri:ArcGISDynamicMapServiceLayer show="layerShowHandler(event)"
                                                       url="http://server.arcgisonline.com/ArcGIS/rest/services/World_Imagery/MapServer"
                                                       visible="{bb.selectedIndex == 3}"/>
                      <esri:GraphicsLayer id="myGraphicsLayer"/>
                      <esri:GraphicsLayer graphicProvider="{lastRoute}" symbol="{routeSymbol}"/>
                      <esri:GraphicsLayer id="inputsLayer"/>                    
                  </esri:Map>
              </mx:VDividedBox>
          </mx:HDividedBox>
      </mx:Panel>
  </s:Application>

  Can someone help a newbie to flex? xD it would be good if you could help me to understand the problem, how to solve the problem and how to avoid it. I want to repair my programming, Yes, but I would also like to learn.

  Thank you!

  If you want to be a MX button, the code would look like:

  private var selectedBtn:mx.controls.Button

• Flash Builder 4: 7 - cannot resolve ViewNavigatorApplication

  Flash Builder 4.7 says that my license has expired, forced me to reinstall.  Put in my credentials, all right there.  Except that now my mobile project said that he cannot solve ViewNavigatorApplication to an implementation of the component.  Latest generation of work used Air 3.5.  I tried to superimpose different versions, 3.5, 3.6 ac2 ac2, even the old 3.5 no longer works.  What is going on?!

  What did you do to get the ViewNavigatorApplication and other flex tags to work with the new AIR sdk?

  [UPDATE]

  So if you have a Flex app, you cannot use version 2.0 of the CSA in the SDK.  The air sdk download page is a small link which will lead you to the right sdk.

• Cannot open websites, error DNS when the ping command cannot resolve the name

  Cannot open all websites on a PC. (other computers on the network can access the sites without a problem)
  Error message is "Internet Explorer cannot display webpage."

  I can ping (internal and external) of the IP and gateway addresses.
  Ping translates:
  C:\>ping www.yahoo.com
  Ping request could not find host www.yahoo.com. Please check the name and try again.

  Nslookup translates:
  C:\>nslookup www.yahoo.com
  Can not find the name of the server for the address 192.168.0.1: non-existent domain
  Default servers are not available
  Server: unknown
  Address: 192.168.0.1

  Non-authoritative answer:
  Name: www-real.wa1.b.yahoo.com
  Address: 69.147.76.15
  Alias: www.yahoo.com, www.wa1.b.yahoo.com

  Pathping translates:
  C:\>Pathping www.yahoo.com
  Unable to resolve target system name www.yahoo.com.

  The problem occurs on a wired and wireless connection.
  Reset TCP/IP via netsh int ip reset c:\ressetlog.txt results in the following in the log file error message:

  discount Linkage\UpperBind for USB\VID_0B05 & PID_1723\5 & 2461925A & 0 & 5.  incorrect value was:
  REG_MULTI_SZ =
  SymIM

  Is there a total of 9 errors in the log similar to the one above.
  The host file has only 127.0.0.1 in there.
  Clearing the cache of the arg, flushing the DNS and do a repair on the network connection does not resolve the problem.
  Install a new network device does not resolve the problem.
  I also deleted all the antivirus software and security, including firewalls.
  The Windows Firewall is disabled.
  Boot in safe mode with Networking does not solve the problem.
  Running Winsockfix does not solve the problem.
  Internet Explorer 8 (reset web settings has been done)
  Windows XP Media Center with SP3
  Execution of the IE Diagnostics results in an error 12007 the server name or address cannot be resolved.

  Get the end of the line...

  Any other ideas?

  Thank you

  Larry

  Sorry for the late reply, but I did not have access to the MS Web site for a few months.

  I tried your suggestions, they do not work.

  The resolution is to do a repair of the operating system out of the CD.  Who cleared up the problem.

  Thank you

  Larry