Cannot start on battery.

Hi, my S10e doesn't start when the battery is installed, if I only run on external power it boots fine. I bought a new battery and the problem is always the same. This is a problem not being able to work on the road. Please let me know if any of you have any ideas.

Flemming

Hello, I speak little English, so I´ll try to be more explicit I can be, try to upgrade the BIOS, since the page lenovo´s there are options to request the correct BIOS, fill it with information from your PC. Salu2

Tags: Lenovo Notebooks

Similar Questions

  • Portege Z930 cannot start with installed RAM module

    My laptop Toshiba Portege Z930-108 has stopped booting with any module of RAM installed in the support.

    If I remove RAM module, laptop computer starts and works fine, but if I install any module of RAM (4 GB 1600 original or a new 4 1600 CL9 or 1600 8 CL11) the computer cannot start.

    The screen stays black and power led flashing two green and two orange and a few seconds later, 3G indicator also on blue.

    This is the only problem I have with this computer, but it's strange.

    I updated the BIOS to the latest version and the problem is not resolved.

    I tried to reset the hardware (http://aps2.toshiba-tro.de/kb0/TSB3B03J90000R01.htm), also I tried to reset the equipment with power button 30 seconds without battery but button without success.

    Any idea on this problem of strage?

    Kind regards
    Lito.

    I guess you used bad RAM or not fully compatible modules.
    It's the only plausible explanation.

    I recommend you to order the RAM modules recommended by Toshiba that are:

    4 GB DDR3 - 1600 PA5037U-1M4G

    2 GB DDR3 - 1600 PA5037U-1M2G

  • Tecra M9 - TPSMain.exe cannot start because CpePerf.dll was not found

    Hi and help,

    searched the Web and found other discussions of the forum with similar questions.
    Tried all suggestions, nothing worked. I'm not very good on the computer but you can find my way. In any case...

    After connection messge pop messages - up in succession, similar to: TPSMain.exe cannot start because CpePerf.dll was not found then: TPSoddctl.exe cannot start because CpuPerf.dll not found

    Computer works very well but Power Saver start is not automatic and can't select it from the Panel... "" Toshiba power saver does not work. "
    so select the power options... "could not start because the CpuPerf.dll is not running.
    Did all the research on the net and followed all the tips... i.e. unistall saving in safe mode, uninstall toshiba common utility can uninstall fatal error 0x7e

    Then download Ccleaner, inspections, uninstall with Ccleaner same fatal error.
    In support of Toshiba and tried to install Power Saver... same problem will not install.

    Thus help help help if possible.
    Computer works well but popping up messages are annoying and I'd love to sleep to extend battery.

    Tried the system restore, even though I doubt that it affects the files... Another problem "cannot complete system restore"... tried this several times and cannot restore the system either... What is happening?

    any help please
    Tim

    Hello

    I think you can solve this problem, recover the laptop.
    But that would mean that the whole HARD disk should be formatted and would be installed everything again, I put t know if this is an option for you

    It turns out that something will not with the Toshiba Power Saver installed and, consequently, the popup message.
    Usually new installation of GST should help. But it was not and I m wondering why

    Maybe this is s question really an OS since system restore help (to the previous state) didn t

    He s strange question right now I can suggest only a new recovery

  • Cannot start the HP Pavilion dv7 - Intel(r) WiFi Link 5100 AGN

    the WiFi has been disabled by the Device Manager, and I can't activate it

    When I get in the Device Manager, one! sign was shown next to Intel(r) WiFi Link 5100 AGN, and I click Properties, the device status displays the message below:

    "This device cannot start. (Code 10)

    Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

    When I click on "Find solutions", it displays 'could not load driver software' and no solution appears

    I tried the function "update driver" and still no idea to him.

    not the product. My dv7 is VQ971PA #AB5. Model no. dv7-2124TX is

    Thank you!

    Hello

    You have a few options in my opinion please try these steps can help you solve your problem.

    (1) unplug the battery adaptor & then press on & press and hold the power button for laptop for 30 seconds then switch on and check if the wireless led lights.

    (2) go to Device Manager then uninstall the drivers wireless network card and restart the device and check if the light is on.

    (3) try to do a system restore to the date where unit was working fine.

    (4) Please update the Bios driver & wireless from the HP website.

    (5) click on start search type Recovery Manager, and then click on it once select Yes on user access control, and then select I need immediate help and then select driver and select request recovery driver wireless and install it and then restart the device.

    (6) If you are comfortable with reinstalling the wireless card that will be on the rear panel of your device you can try this steps as well.

    If you still have the same question so you must call HP tech support and get the replacement of the part.

  • Cannot start ATI Radeon HP g6 2304 su.

    I bought a new HP laptop. There are two cards - one integrated into iCore 5 - Intel HD 4000 and another - ATI Radeon 7670 M. The version of the BIOS is F.22. Operating system is Windows 8 64-bit. Memory is 8 GB of RAM.

    I had a problem with ATI Radeon graphics card. I spoke with the HP support center and they told me to install the chipset drivers, then only the drivers of ATI graphics cards (because the Intel graphics drivers is integrated in this driver). When I click on desktop I can see Configure Switchable Graphics and as I have read is in the dynamic menu mode and can choose application to run in saving energy or high performance.

    The problem is that I really think that cannot start ATI. For example, try to run a game online. I added in high-level sport, my battery settings is High Performance, AC adapter / CC is connected and when the game starts, can not choose the ATI card, only Intel HD 4000 is listed.

    In the Device Manager has also two cards listed (Intel HD 4000 Radeon 7670 m) and but in tools such as dxdiag is listed only Intel HD 4000, Information System Microsoft rendering driver base and name Intel(r) HD Graphics 4000, AIDA 64 in Windows Video and PCI/AGP video only listed Intel HD 4000 is listed.

    In the BIOS isn't an option to change a dynamic setting, or fixed.

    Could you give me an advice how I can start the card ATI Radeon.

    Sorry for my late reply.

    Then I tried everything.

    And finally, I take a computer to the original service.

    After a few days I guess. And now seems that everything is OK with ATI.

    Added a few games to High Performance began and after begins TechPowerUp GPU - Z. The sensors for the base ATI clock are moving. So I think everything is fine now.

    Understand that they solve this situation as older pilot.

    Thank you for the support.

  • Cannot start Windows on first boot (works after restart)

    I recently removed the dust in the housing using a bellows, at the end of which I had unplugged and removed by the drive hard and video card. After reinserting the components and start the computer, I heard a continuous beep sound while the screen remains dark. After the reopening of the case I noticed that I forgot to plug a wire into the video card (PCI I think) I plugged. After you start the computer again once it wasn't a beep more and I got the video. However, Windows does not load on first boot more. He will go as far that the loading screen of the bar after which I get a 'no signal' and the computer restarts. I will get a screen with the message that Windows cannot start, probably due to software or change of material and a number of options. When I choose to start windows normally it will mostly start normally (sometimes I need to repeat the process) and I can use the computer normally (I use it now). A reboot, the computer has been shutdown very slowly and later wouldn't pass the default splash screen, but it has not reoccured.
    Another small issue, I'll have is a regular of the screen flicker.

    I used the drive control to the start of several times. I tried to address this problem by starting the computer with the Vista installation disc and select Repair, but I was not allowed to fix the menu says there where no problem. I reinstalled Windows (and I can't be fully updated all the drivers again, hance perhaps the flicker of the screen?), but to no avail. The closest thing I've met on the internet who resembled my problem was this: http://answers.yahoo.com/question/index?qid=1006011905618 so, I replaced the BIOS battery, which once again changed nothing (BIOS holds settings BTW). In fact, once I'm on Windows I would seem to have a computer that works very well. The issue doesn't bother me so much if I wasn't worried, that it could get worse.

    I have Vista 32 bit, Intel E6750 CPU, card mother Gigabyte GA-P35-DS3, Geforce 8800 GTS 320 MB video card, 2 GB of RAM, Samsung 400 GB HD Vista has been entirely updated (including SP2).

    Hi CeCoRM,

    I suggest physically wipe you the hard drive again by blowing air earlier could have pushed the dust particles away on the inside.

    I would recommend also you post your question in the TechNet forums for assistance.

    Hope the helps of information.

  • Zune not working "this device cannot start. (Code 10) »

    Zune 120 suddenly stopped working on Windows 7. Its chagred not do anything. The battery is completely discharged. I can't reset it. I see black Yello Trainagle with exclamation point in Device Manager. The device status is: "this device cannot start. (Code 10) ».
    Version of the device: "4.2.58.0. I tried almost all KB articles related to Zune, but no luck. I tried the same thing on 2 laptops more and a desktop computer but same problem.

    I also tried different sync cable no luck. Now, since it is completely unloaded, I even cannot reset its software. I tried manually to install its driver software with no luck! Please guide.

    Please guide.

    Engineer @ MS

    Hi Jordan,.

    See the article depending on the error Code 10 and troubleshooting for this issue:

    http://support.Microsoft.com/kb/943104

    I hope this helps!

    Debra
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • My sound card does not work after working yesterday. "This device cannot start. (Code 10) »

    Hi support team!

    I have a HP Pavilion zv6000 and my audio does not work and I enter the Manager of devices and displays this error: "this device cannot start. Code 10 "after this I installed my audio driver from the site and still the same problem.

    With repsect, OZNalex.

    OZNalex wrote:

    Hi support team!

    I have a HP Pavilion zv6000 and my audio does not work and I enter the Manager of devices and displays this error: "this device cannot start. Code 10 "after this I installed my audio driver from the site and still the same problem.

    With repsect, OZNalex.

    Hello

    First do a hard reset.

    Please go through this Hotfix from Microsoft for the error you are getting.

    Please uninstall & update audio driver & BIOS after checking, you have such version specified in the site pilot here on the website of the HP product . Reboot after that. Do the troubleshooting in the Microsoft Fix document.

    When you're done, shut down the laptop.

    Disconnect the power adapter and remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

    Robinet tap away at the key ESC that you start the computer to launch the Start Menu, and then select F10 to open the BIOS menu.  Press F5 to load the default values (sometimes it's F9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press F10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

    Check if its working

    Thank you

  • Update interrupted - now cannot start Windows

    Hello

    Completely new to this forum and in the world of the system recovery / technical questions will therefore be very grateful for any help that you can offer but please keep clear answers.

    I am running windows 7 on a Samsung laptop about 3 years. During the last weeks I had problems with the battery. When not plugged in the laptop sometimes turned off and the error messages pops up saying occasionally replace the battery. I now only use it plugged into the mains. However, yesterday, when I tried to stop, windows installed updates and the wall socket, broke off. To my horror, the computer turns off so that the update (1 of 31).

    Now, I can't start windows. See below what I tried so far without success.

    Tried to load Windows normally. Key start-up windows screen and then error blue screen and restarts.

    Tried to select recovery at startup option. Through repair screens. Asked if I would restore the system to an earlier era. Tried by selecting Yes and no at this point. So yes, message says not able to repair and asks if I want to send an error message. In the absence, said also unable to repair.

    Tried to start in safe mode. As above - will from the screen windows and error, then blue and restarts.

    Tried to insert the Samsung recovery cd. When the computer starts. Press the key to load from cd. This goes to a windows install page (select language, etc.). Seems to be saying that if I do that I'll lose files?  So not go one more away.

    Have you tried pressing f8 and repair different, but process as well as above - unable to repair.

    I myself am kicking to not fix the battery problem, but I never thought it would happen. In any case, I have a recent backup of most of the files, so not a total disaster, but I would like to save some recent if possible files. The only other option I see is to remove the hard drive and buy a USB connector stada (?) and try to transfer as an external drive. How difficult is cela and what connector do I need? Understand you can not recommend a product, but is there something specific I should look for, and what are the differences between the cheapest and most expensive? Are there more reliable / brands of higher quality that I should look for? Also, if I do this, can I then replace the hard drive and reinstall windows, and it's going to work?

    I have no knowledge of the BIOS so not sure I can try relating to the recovery of base?

    Will be very grateful if someone could help it. I can post more detailed error codes / logs later when I'm in front of a computer if you need.

    Hello

    Thank you for visiting Microsoft Community and your efforts to resolve the issue is highly appreciated.

    According to the description of the problem, you cannot start your Windows 7 computer. This could be if there is a corruption of system files or boot files are missing or damaged.

    I suggest that you want to run auto repair with installation media and see if it helps you repair system files or not. For the execution of the task, I suggest you to try the steps below and see if it helps.

    Method 1

    When you use the recovery environment (Windows RE) to troubleshoot startup issues, first try the Startup Repair option in the System Recovery Options dialog box. If this does not resolve the problem, or if you have additional problems manually, use the Bootrec.exe tool.

    Because you cannot start the computer, you may need to create a bootable Windows installation media, and then do an auto repair, and if this does not help then you try to restore your computer to the previous date.

    Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

    If you are using Windows 7 then the link provided below might help you to download and create installation media.

    Download Windows 7 Disk Images (ISO files)

    Method 2

    If the problem persists, try to rebuild the BCD by using the Bootrec.exe tool. To run the Bootrec.exe tool, you must start the recovery Windows (WINRE) environment . To do this, follow these steps:

    1. Place the Windows 7 installation disc in the disc drive, and then start the computer.
    2. Press a key when you are prompted. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
    3. Click repair your computer.
    4. Click the operating system you want to repair, and then click Next.
    5. In the System Recovery Options dialog box, click command prompt.
    6. Type Bootrec.exe, and then press ENTER.

    See the following link for more information:

    How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

    http://support.Microsoft.com/kb/927392

    Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

    Kind regards

  • Mac cannot start after el captain

    Cannot start after updating mac

    Safe Mode boot removes the system caches that can help after an OS X day or level.

    Follow these steps to start in safe mode.

    1. Start or restart your Mac.
    2. As soon as you hear the startup tone, hold down the SHIFT key.
    3. Release the SHIFT key when you see the logo Apple appears on the screen.

    After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

    To leave safe mode, restart your computer without pressing any keys during startup.

    Try safe mode if your Mac does not end commissioning

  • Firefox is exhausted before but cannot start more

    Firefox is exhausted before but cannot start more.
    I tried the solutions, but it does not work

    Large. Glad to know you have the root of the problem, and thanks for posting back.

    Usually, we suggest that when checking for malware several tools to serve because no single tool is looking for or find everything. The standard help article

  • Cannot start Firefox, crash even in Crash Reporter. Not be able to start in safe mode either.

    Cannot start Firefox. He goes to Mozilla Crash Reporter every time. I can't even start it Safe Mode.
    I tried to uninstall and delete all the files related to Mozilla Firefox in & AppData & and each base registry with RegEdit.

    I have run, or at least try, on a system with Windows 7 64 bit, 8 GB RAM, 314.22 driver for Nvidia GeForce GPU and a CPU Intel Core i5 2500 k CPU.

    Little help would be nice.

    Hi deliubogdan

    Try to remove the extension DataMngr (Datamngr.dll)

    Do a check with some malware malware, analysis of programs on the Windows computer.

    Please scan with all programs, because each program detects a different malicious program.

    All of these programs have free versions.

    Make sure that you update each program to get the latest version of their databases before scanning.

    Alternatively, you can write a check for an infection rootkit TDSSKiller.

    See also:

  • Hi, after you install Minecraft in my iMac, I get this message: "cannot start minecraft, if you run from a dmg, please drag applications and try again. I Don t know how to start the game. Thank you

    Hi, after you install Minecraft in my iMac, I get this message: "cannot start minecraft, if you run from a dmg, please drag applications and try again. I Don t know how to start the game. Thank you

    So what measures through 'install '?

  • Tecra S5 - adapter to display cannot start - Code 10

    Hello

    I have a problem with my laptop (Tecra S5 series).
    Every time when I start or restart my laptop, the screen moves too slowly, it has yellow bands and sometimes is flashing.
    When I open the Device Manager I see the graphics card (NVIDIA Quadro NVS 130 M) with yellow circuit with a brand extension. When I go inside it is said: the device cannot start. Code 10.

    Then I have to go Safe Mode, uninstall the drivers for NVIDIA Quadro NVS 130 M, reinstall and restart. I noticed that when this video adapter is OK, so I don't have problems with my laptop screen.

    Can someone help me?

    What operating system do you use?
    I put t know since when you have this problem, but if this happens again and again I recommend you to install original OS that you got with your laptop. It contains the original, including the display driver drivers, and something like that should not happen.

  • Cannot start the satellite M35X

    Hi all.

    Cannot start my Satellite.
    When I push the power button, it turns on, the blue led is ok but the HDD led blinks 1 or 2 times or it happened when it is not clear at all and put the laptop off, but the power button remains lit.

    However, from time to time, it starts up, shuts down load the XP but after 1 minute.

    I have reinstaled recently the WinXP, and I did a bios update. Before that, the laptop didn't have this behavior, however, the XP raported me that the hard drive is faulty.
    I figured it is something related to the HARD drive.
    What should I do?

    How can I be sure that the HARD disk is wrong?

    Hi mate,

    If your HARD drive has bad sectors, you must exchange it ;)

    For example before doing this, you can check for bad sectors using specific diagnostic tools HDD as Drive Fitness Test:
    http://www.HitachiGST.com/HDD/support/download.htm#DFT
    Here, you can download an image file to create a boot disk. Then boot from it and to start the test, it is quite easy! ;)

    If your HARD drive is faulty, this tool should recognize this.

Maybe you are looking for