cat/etc/oratab watch dbstart ' don't and DB is still up on the system startup

Similar Questions

• Backup and restore > Creat an Image of the system: program cannot find a WD external hard drive

  I recently bought and installed a MyBook 2 t Western Digital network drive.  It installed fine and I can see listed on the 'Computer' desktop and icon within the Norton backup program.  I have setup my regular backup routines successfully.  On the bottom: I recently lost a hard drive and replaced with a new one and spent several days to restore the system and install any patches, etc.  It was particularly difficult to get the installed Windows 7 SP1.  I wanted to install this drive external hard to use Windows built-in Backup and Restore to "create a system image.  When I select this option, the program asks me where I want to save the backup. I select the button of "on a hard drive" and search for the external hard drive.  It notes the two internal hard drives, external hard drive is not found.  Support WD provided the following instructions:

  ********

  If you have mapped the drive and backup Windows and restore is not able to
  see even the mapped folder. I recommend you to check that the network
  Services by clicking on "Start" and type "Services.msc" and press ENTER.
  It will bring up the Services Control Panel. You will see all the services on
  your computer is listed here.

  Since we are here, we will check that all the
  Associated network services are rising and run correctly. You will verify the
  Next:

  -SSDP Discovery
  -Network Access Protection Agent
  -Network connections
  -Network list service
  -Knowledge of network locations
  -Service of Network Store Interface
  UPnP device host-

  All of these Services, under the State, must be either "Manual" or "Automatic" in
  in order to work properly. If any of these Services are 'off '.
  in the status area, you will need to enable it. To do this, you right-click
  on the Service and click 'properties '. After that, the "Startup Type".
  Set it to automatic, and then close.

  In addition, you will need to check
  as options network and sharing are all set up correctly. To do this, which
  you need to do is click on 'Start' and open 'control panel '. There, click on
  "Network and Internet" or "center network and sharing", according to the
  display type. After that you are in "Network and Internet", you can select 'network '.
  'and Sharing Center'.

  In "Network and sharing Center", on the Panel for
  the left side the last option should read "advanced by change sharing settings."
  That open. On the area of "work at home or", set the parameters as follows:

  -Network of discovery-
  -File and Printer Sharing - on
  -Public folder sharing - suite
  -Media Streaming - suite
  -File sharing - connections
  128-bit encryption is very good.
  -Password protected sharing - Off

  ********

  Everything was as expected, but he has yet to find the external hard drive.  When it doesn't work, they punted (well...' this isn't our software "").

  I am running Windows 7 Home Premium, 64-bit OpSys

  The drive is MyBookLive 2T WD network drive.

  Any ideas?

  Thank you

  In Windows 7 home Windows backup won't backup to a network drive.  W7 professional and higher.  There is a possible work around

  Windows 7 Home Premium network backup

  http://www.overclockedtechies.com/2012/02/Windows-7-Home-Premium-network-backup/

• Envy 17 2180el can I add a second hard drive, and then choose bios/boot of the system with which to start?

  Envy 17 2180el can I add a second hard drive, and then choose bios/boot of the system with which to start?

  in the case give me the link of a hard disk of type to add

  Hello

  While you can certainly add another HARD drive in the Bay of secondary drive (you must also support and the connection cable) you can't boot from it - only in the Bay of primary HARD drive is bootable.

  Kind regards

  DP - K

• I bought a Apple Watch opportunity in a big box store and it is still attached to the old owners account. How to reset or remove without knowing who was the former owner?

  I have Perchased a previousmy belonging to Apple Watch at a big box store and it. Is still attached to the old owners account. How can I reset or remove it?

  Activation"lock" must be removed and the process is completed by the original Apple ID ".

  owner before another owner can use the item; have you read the article from where

  You may have started your question here?

  • Activation lock on Apple Watch - Apple Support

  You must return the watch brand new/used in the big-box store where you bought it and

  a the management of refund your purchase price or Exchange the item by a unused.

  The instructions in the link of the page above apply mainly to the buyer before, etc.

  of the product, similar to the distance to give or sell an iPhone or nearly any other Apple product...

  Disable locking Activation before you send your Apple Watch in service, sell it or give it

  Before you send your Apple Watch in service, sell it or give it, you must disable blocking of Activation

  on your Apple Watch. Just cancel the twinning of your Apple Watch from your iPhone:

  1. Keep your iPhone close and Apple Watch.
  2. Open the app shows on your iPhone and tap the tab My Watch.
  3. Press Apple Watch, and then click Disable pairing Apple Watch.
  4. Enter your Apple ID. If you forgot your Apple ID password, you can reset it.
  5. Tap again to confirm.

  If you are unable to access your iPhone or Apple Watch, or if your Apple Watch is not paired with your iPhone and

  You must disable the locking of Activation:

  1. On a computer, go to iCloud.com.
  2. Sign in with your Apple ID and open settings.
  3. Under my devices, click on your Apple Watch.
  4. Click the X next to your device.
  5. Click on delete to confirm.

  In any case, I'm sorry it seems to be little or nothing, I can help you for this purpose.

  Good luck in your discussions with people, where you bought the watch...!

• EVENT ID #12 AND #11 CD DRIVE DISAPPEARED FROM THE SYSTEM WITHOUT BEING PERPARED TO REMOVE

  MY FATHER HAS A MACHINE E AND THE CD ROM DRIVE JUST DISAPPERED WE TRIED TO PUT ANOTHER CD IN IT AND IT PLAYER DOES NOT SHOW EITHER. I have CHECKED the OBSERVER of EVENTS AND IT SAYS THE DRIVE has DISAPPEARED of THE SYSTEM.

  Hello

  Please do not type in capital letters as it is difficult to read and regarded as yelling.

  This problem affects both/all readers is expected when it comes to the top.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Why I can't download Flash Player on my MacOSX10.8.6?  Adobe does not accept my password and it is impossible to change the system from Adobe!

  I tried a million times to download the latest version of Adobe Flash Player on my MacOSX10.6.8.  Adobe does not accept my password - and it's the system to change passwords going no where.  It's Kafka-esque!

  Computers Apple will ask your system password when installing new software. It's probably nothing to do with Adobe at all.

  Try the password that you used when you set up your Mac.

• I don't get updates to windows, I used the system and clicked on update

  I clicked on the automatic updates - have not received any...

  You must be level SP3 before you use Windows update.

  http://support.Microsoft.com/kb/2497281
  You may be unable to access the site Web Windows Update in Windows XP, Windows 2000 or Windows Server 2003

  To determine which service pack is currently installed on your computer, follow these steps:

  1. Click Startand then click run.
  2. Copy and paste, or type the following command, and then click OK:

  winver

  A dialog box displays the version of Windows and the service pack that is currently installed on your computer.

  If you haven't already done so, you will need to install the SP2 and SP3 (SP1 note no longer exists).

  How to obtain the latest Windows XP service pack
  http://support.Microsoft.com/kb/322389

  SP2 - http://www.microsoft.com/en-us/download/details.aspx?id=28 (for single PCs too)

  For Windows XP Service Pack 2 installation procedure
  http://support.Microsoft.com/kb/875364

  Steps to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717

  It is stated in "How to obtain the latest service pack XP" is.

  If you have problems obtaining the service pack from Windows Update, you can download the package of standalone update from the Download Center. This page will say that this installation package is intended for it professionals and developers. However, you can download this file safely. The following file is available for download from the Microsoft Download Center:

  Download the Windows XP Service Pack 3 package now

• NB100 - failure and how to do a restore of the system startup?

  I tried to do an update on my Toshiba NB100 11R (less than a month) and it failed, and now I can't start.

  Unfortunately, I don't know anything about Linux-based systems. Tried to boot from the CD (provided) with an external USB, disk drive and can not find anywhere to make a record of rollback/beginning of restore boot from, and I'm now stuck with a dead machine.

  Any suggestions gratefully received! Thank you, Bill

  When you turn on, press F12 repeatedly to access the boot menu - from there, you should be able to choose to boot from the recovery CD (not sure in your case if it counts as a CD or a USB device - trial and error I guess!).

• Lost remote but don't pair new because an update of the system is necessary.

  Hi all. I have an apple tv which is a few years old. Maybe 2. I can't check because I can not enter the screen. I can turn on the unit through airplay, but cannot pair my phone with that and use it as a remote control because there is a system update and I can't get rid of this menu. Any ideas of what I can do? If I buy a new one, should I pair it so? I really want to pay for a new brand. Any help is greatly appreciated. Thank you!!

  -Jared

  You get an apple remote-perhaps borrow from a friend. Get through the update and match the remote app and then return the distant friends. Otherwise, you will need to buy one - I think they are$ 19...

  or maybe you can find a universal remote that will help fill the gap. I have the harmony remotes and he controls EVERYTHING, but it's expensive...

• Windows Update tried to install updates from last week that I really don't need. Why if they fail the system to keep trying to install? It's boring

  Microsoft windows update

  http://www.Microsoft.com/Windows/downloads/windowsupdate/learn/windowsvista.mspx

  Read these links. http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Change your update settings and hide the others that you do not want.

  It comes with Vista, upgrade install and activate Forum:

  You will get the best help for any problem of Update/Service Pack update Vista Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• I have a XP Service Pack 3 full OS disc that I installed on an old Dell. This computer was dead and I would like to install the system on my newest laptop. Can I transfer the license and how do I do this?

  The OS is installed on a hard drive that I use now as a second drive in my desktop (most recent) DELL PC. I want to be able to install the OS XP disk on my laptop. The DELL PC has its own XP license - I have two drives OEM XP SP3 OS. What is the process by which I can do a fresh install of XP that was used on the old DELL?

  Download and install .NET 3.5 (which includes 2 .NET)

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=21

• My battery, sound and network icons have disappeared from the system tray. I tried to fix with some resolutions that I found on the internet, but still no go...

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  http://www.Vistax64.com/tutorials/106787-notification-area-system-icons.html

  Read the tutorial above.

  See you soon.

  Mick Murphy - Microsoft partner

• Is it possible to install, license and use Photoshop and Premiere Pro (versions CC) in the systems permanently disconnected from Internet?

  We have military systems without any internet connectivity at all where we would use these products. Activation of the license via phone or export/import license files might be acceptable, but not more.

  Are there important limitations to be aware of that it can be made to work?

  The software needs to have access to the internet periodically to confirm the subscription remains in good standing.

• Premiere Pro CC6 and CC7 will not video or still images to the timeline for editing.

  First Pro CC7 and nc6 don't add video or still images to the timeline for editing. It wil play the clip, but that's all.  I tried a lot of different vidoe, mov, avi files and others more, photo jpeg, but not matter what I do I can't move to the time line to edit. I have the 30 days trial version. I watched the tutorial, done the same thing, no luck.

  Ideas and help appreciated otherwise I'll just bin the whole program. I tried it on TOC Final 7 pro and there is no problem (it's on the mac, the first pro is on pc).

  Chances are that you want to create a sequence to put them.

  FAQ: How to choose the right sequence settings?

• When I close thunderbird is still running in the background and always using data?

  I'm with an internet provider that has limited use of data per month. If I close Thunderbird when done using it it is still running in the background and using the data or is it closed here for not to retrieve messages or using the data?

  When you close Thunderbird, it cannot check or retrieve new messages.
  Not sure what you mean with "always running in the background.
  When you close Thunderbird is closed. Period.