Change default address "scan to network" on C2665dnf

Similar Questions

• Changing the address of the NETWORK card

  I have to assign a new vswitch to my host and a NETWORK card is available, but there is no IP assigned to this network adapter.  I need to assign an ip address to vmnic2 and then attach it to my new vswitch.  Anyoen can help with the command line?  Thank you.

  You cannot assign the IP address range. I assume you mean "observed IP range" in the NIC properties - it's just for your info, packages of which NIC subnets see.

  There is nothing to configure. Simply create a vSwitch and add physical NETWORK adapter.

  ---

  MCSA, MCTS Hyper-V, VCP 3/4, VMware vExpert

  http://blog.vadmin.ru

• To change default Internet connection sharing IP address range and subnet mask

  Hello

  When the ICS (ICS) is enabled on a NETWORK adapter that is connected to the direct Internet line, the second NETWORK card automatically gets the 192.168.137.1 IP address and subnet mask 255.255.255.0. As the first IP address in the address range is located on the second NIC in the computer, the other client computers receive the other IPs in the same range, for example 192.168.137.2, 192.168.137.3 and so on.

  In my case, I already have the static IP network using Network 10.0.0.0/8, I want to change default IP of 192.168.137.1/24 to 10.0.0.1/8. I managed to change the IP in Regedit - HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\SharedAcces - parameters - ScopeAddress / StandaloneDHCPAddress

  that works, but default IP 10.0.0.1 has the subnet mask 255.255.255.0, how to change the subnet mask of 255.0.0.0.

  Help, please...

  Hello

  Thanks for posting your question on the Microsoft Forum.

  I suggest you to ask your question in the TechNet forums.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking&filter=AllTypes&sort=lastpostdesc

  TechNet is watched by other computing professionals who would be more likely to help you.

  I hope this helps.

  __________________

  Thank you best regards &,.

  Isha Soni

• How to read the multiple slave devices in a RTU modbus RS485 2-wire network without changing slave address manually?

  Hello

  Currently, I can read data out of multiple using the attached VI DAQ devices by manually changing the address of the slave on the front panel that determines what slave to read the data. However, I want the VI to do it automatically for me instead of me manually by clicking on the buttons on the front panel to change the address of the slave. In other words, the VI should read data off devices 3 slaves and save them to a database of all the 1 second (sampling from 1 sec interval). I tried to use the structures of the case, timed sequences and delays, but I'm still not able to get what I wanted. My current VI is a modified version of a VI library modbus - 'MB series Master query read input registers'. No idea how to do this?

  IM pretty new to LabVIEW, so don't kill me if im away here

  Could replace the cluster 'Series settings' with the attached structure solve this problem?

  The real deal will be just the value back to the default (1).

  -Tom

• (Redirected) C2665dnf clour printer-cant scan to network MFP

  I just bought a C2665dnf clour printer MFP.  for the life of me can not configure scan to network.

  Can I use my pc to use the scanner but it is so time-consuming trying to convet a jpeg to PDF then reroutes it to the network drive.

  can someone help me please?

  Simon

  Best of this post in the Forum of devices/printers, here:

  http://en.community.Dell.com/forums/3528.aspx

  Bev.

• Changing the MAC address of the network management

  Hello

  We have 2 servers ESXi 4 in our network. We do not know why, but both have the same MAC address on the network card virtual for the management network. That's a lot of problems with the connectivity of one of ESXi servers.

  Is it possible to change the MAC address?

  Best regards

  Robert

  Removal and addition of the vswif of the service console should generate a new MAC address.

  esxcfg-vswif - l

  Note the detail.

  esxcfg-vswif vswifN d

  where N represents the number of vswif, d Deletes

  esxcfg-vswif - a n-i < IP > < vswifN > < portgroup > Pei, netmask

  is the command to add a new vswif, even when N is the number of vswif.

  Simon

• Change the default address fields

  Hello
  
  Is it possible to change the default address fields (account, contact addresses)? For example, the user wants to add 'States' when the country 'India' is selected.
  
  Thanks, Sab

  SAB, in this moment, it is not possible to change the address fields. Currently, the address fields are determined by the selection of countries.

• Color LaserJet MFP M476 Pro: Scan to network folder

  Finally decided to try to set up the scan to a folder again... but run into the same issues as before... invalid name and password

  The printers and mac are on the same wireless network and have no problem printing.

  Using Macbook Pro running El Capitan 10.11.6 - has only one user on mac... Bob

  Not yet completed:

  Folder created under users\Bob\Scan

  Went to the settings and turned on file sharing and add the Scan file to the list of shared folders and make sure "Bob" is listed as a user with read/write privileges.

  Page web accessible to 192.1.168.88 printer

  Selected scan / file Configuration of the network

  inpu the following parameters

  Display name - Scan

  Network path - \\192.168.1.94\Scan (confirmed this ip address is the ip address for the mac)

  User name - Bob

  PW - same as the one used to log for Mac (verified by up to 30 times!)

  Continually get "user name or password is incorrect. Make sure that the user name and password are correct"

  Any suggestions?

  Hello

  As long as you enable sharing of Windows files for the user the pritner will not be able to connect because it only supports SMB.

  By testing, I see the user as available for selection Although SMB is off...

  By searching online, I do not see messages indicating you will not be able to set in Windwos God file for the password iCloud user, may it be linked? :

  https://discussions.Apple.com/thread/6708192?start=0 & tstart = 0

  You can try creating a new user account and set it for this purpose (you won't even need this user to login, just set it to the printer while offering both users access to that folder, then you can continue to use your current users).

  Another thread indicate that change the password solved the problem:

  https://discussions.Apple.com/thread/6629743?start=0 & tstart = 0

  For any other questions, I suggest to start a thread at Apple Support communities, as long as you won't solve this problem, the printer won't be able to connect.

  Please let me know any progress,

  Shlomi

• Another change of address Mac to my original Mac address?

  Hello.
  My problem is another change to my mac address mac address! I mean when I click Device Manager > network adapters > then click on properties of my network card > then click on advance tab > then click on the property of network address...
  We have two Options here for Network Address.One is missing and one is the value you should enter a Mac address custom.
  But I wish to address not present for my connection.but I have a problem here.when I don't put not present and then click ok, you think that later, I use my own address.but of mac, it is not true!
  When I open cmd and type ipconfig/all, there show me information as the physical address for my network card! So it shows me the wrong mac address.because I know my mac address is one another thing! I want to say is of me D8:5 D 00:16:E6:19:AB:C9.but ipconfig show: 4 c: B1:D9:13.
  Now I want to know how can I change this wrong with my original Mac address mac address without I enter the default network address!.
  tank you cherish!

  Hello.

  Have you tried all of these steps? This is how to correctly allocate your own MAC address:

  1.

  Click on the "Start" button and click on 'run '. Type "cmd" and press "enter."

  • 2

  Type "net config rdr" and press "enter." Note the long string of numbers and letters in braces on the screen. Leave the command prompt window when you are finished.

  • 3

  Click on the "Start" button and click on 'run '. Type "regedt32" and press "enter."

  • 4

  Navigate to the registry subkey "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318}" using the navigation on the left side of the window pane.

  • 5

  Click each subkey in the right pane (from the subkey is 0000 and passing by each in turn) and check the "NetCfgInstanceID" for each key until you find the one that matches the value that you noted in step 2.

  • 6

  Click twice on the "NetworkAddress" key, then enter the new MAC address you want the network card to have.

  • 7

  Click on 'OK '. Restart your computer to apply the change to the settings.

   

• Difficult to change IP address in WRT160N

  I am trying to use my 160N as access point and I read on the Linksys site on how first, replace address IP 192.168.1.2 and then disable DHCP and save the changes.  The 160N is plugged into my laptop (address IPv4 192.168.1.100) and the laptop is not connected wireless to any other network.

  After I saved the changes, the next screen says "change successful" and then I hit the continue"" button.  There is a 20 second pause.  The bottom of the screen shows the laptop tries to connect to the new IP address, but cannot. I started from.  I try to reconnect to the configuration using the new IP address page, but can't.  I use the old (default) IP address and still not get the configuration page.  I have reset the router 3 times do the same exact process and get consistent results.  Linksys, I called and they told me that I had to change the third digit and not the last number to avoid any conflict of IP so I tried without success.

  Why can't I change the IP address?

  1. disconnect the E3000 WRT.
  2 wire a single computer to the WRT.
  3 reset the WRT by pressing the button of reset for 30 seconds.
  4. open the web interface at http://192.168.1.1/
  5. change the address LAN IP of 192.168.1.1 to 192.168.1.2.
  6 turn off the DHCP server.
  7. save the settings.
  8 disconnect the computer from the WRT.
  9. wire one of the LAN ports of the WRT to the E3000.
  10. connect your computer to the E3000. Try opening http://192.168.1.2/

  If this does not work, open a command prompt window and type "ipconfig/all". After the output full.

  In addition, make sure you have a working internet connection on the computer without worrying if it is connected to the E3000 or the WRT.

• I just changed email addresses. TB guard shipping copies of emails to the new address in the old

  I can't find a place where TB directs the emails in any account to a default account. Having just changed email addresses. I have two accounts in my TB program. For every email that I receive, for each account, I get a message saying that he was sent to the old account and is not available, because the ISP has closed this account. How to change or remove this automatic redirection? I have not deleted this account in my list of TB yet, because I'm still working through the files left there to decide whether to move or delete the individual emails. Simply remove this old account to solve the problem?

  You need to sign in to your account via a browser and check your account settings.
  There is no such thing as a "Thunderbird account. Thunderbird is an email client that allows you to retrieve messages from an account that you set up with your email provider.

• OfficeJet 8620: Error using scan to network folder - although the EWS test demonstrates the success

  I have configured the 8620 via the integrated Web server for scanning to \ \Scans < ip address of my macbook > the 'test' function's successful return.  However, when I run a scan to network folder in the control panel of the printer, I get the error: "cannot write in------< ip address > \Scans.» Destination folder is read-only, has the wrong permissions, or is no longer available. "I don't see how that's possible given the test of EWS.  I confirmed that the file is read-write for all.

  Hi @tfeeneytx

  I see that you have taken the lead and sent the scan to network folder problem you encounter as you mentioned that you on your previous post. I'd be happy to help you with this also.

  Please use the following document to ensure you have the analysis of the configuration of the network folder correctly; Scan from the control panel (including the Scan to Email, in PDF format, and to a network folder) for Printer series e-all-in-one HP Officejet Pro 8610, 8620, 8630, 8640, and 8660.

  Please also ensure you have the latest update of the firmware for the printer; Update of the Firmware 8620/8625 e-all-in-one printer Officejet Pro HP.

• HP Officejet 4630: Change Format Printer Scan

  If I scan directly from the printer to the document format is defined in PDF format.  I can change it to another format?

  Thank you.

  Hello

  What do you mean another format (s). By default, the scanned documents are pdf files and scanned images (when select scan photo) are jpg files. By using the software from your computer, you'll have more options.

  Kind regards.

• HPOfficeJet Pro 8630: Scan to network folder fails

  I have recently reinstalled Windows 7 without password on my computer, although the previous installation did use a password. Now I can not scan to network folder (error message that the user name or password is incorrect), or save faxes on my computer. (error message that there is no communication between the computer and the printer). I checked the windows firewall, I restarted the router, printer and computer. I use an Ethernet connection to the router.

  Hello

  First of all ensure that protected by password sharing is disabled for your operating system, otherwise it will fail:

  From the Control Panel, under network and Internet open the network and sharing Center.

  Ensure that the network type is displayed as a home or work network, if it is listed as Public network click on it and select home or work.

  In the left pane click on change advanced network settings and select turn off password protected sharing.

  Search for now any change.

  If you have problems to right click on the Shared folder, and then select Properties.

  Ensure that the folder is shared as sharing.

  Click Advanced, and then click permissions and ensure that your users have all permissions to this folder.

  Hope that helps,

  Shlomi

• Impossible to configure a scan to network folder in OS x 10.7 Lion for officejet 8600

  The online system will not recognize my name from the network folder, when I try and set up a scan to network folder. The product is an Officejet 8600 and iMac OS x 10.7 Lion running... Any ideas?

  Hi Bill,

  Please be sure to use the IP address rathert han Hello hostname:

  Locate the IP address of the Mac (you can find it by opening system preferences > network.)

  Check the IP address in the Wi - Fi or Ethernet connection.

  That provide the printer path shared help

  \\[MACIPADDRESS]\[SHAREDFOLDER]

  (for example \\10.0.0.1\scan as example)

  Additionally, make sure that SMB sharing is enabled in the sharing settings:

  Go into System Preferences > sharing.

  Enter the parameters for file sharing.

  Click on the settings button.

  Make sure the option to share files and folders using SMB (Windows) is checked.

  Finally, check the folder appear in the shared folder column and users have write permissions assigned.

  For any other question, it may help if you can put the parameters supplied on your Mac and those who put you in the EWS page so.,.

  Shlomi