Change SNMP bulk
I'm looking for som support in how to use Vcenter Configuration Manager 5.3 to change the name of the community, the destination of interruption and the security settings on the SNMP services on all of our Windows servers. I was not able to find a way to list this info and find a way to change this.
Thank you.
Two things to look at. First of all, the machine you are using your base line to ensure that it is configured correctly and that all the settings that you want are set manually. Second, make sure your filter sampling is pulling back enough data. If you use the default filters for the registry, I think they'll only 3 levels deep. My suggestion would be to create your own custom for SNMP filter. It would be a collection filter registry start set path to HKLM\SYSTEM\CurrentControlSet\Services\SNMP and to the collect at the level I would have put to all the. Remember with the new filter and you should start to see all the parameters.
Regarding the change of in bulk, if you just add to an existing Setup or change existing settings that can be easily done through the console once you get the filters to work. If you have no parameters or completely change their I did it by exporting a well-known registry and then key to deploy using a remote control. I then clean goes back through the console to remove the old keys that are no longer needed. Another tip which may help to ensure that everything is gettting the right settings is to create groups of computers for the settings you want. So if you add a key, you can create a machine group of all systems that do not have the key.
Tags: VMware
Similar Questions
-
Timetable change in bulk Message Notification
Jeff,
You have all the tools available to make changes to schedule of Notification of Message to subscribers of bulk? I need to extend the annex below the default values to 06:00 to 18:00. We were not aware of the requirements until after that all subscribers have been created, if the model did not contain the exact time. I have changed for future users, but I wish I could change the subscribers (1000) in bulk rather than by hand. Using Unity 4.05.
Thank you!!
Adam
OK, if you mean to 06:00 to 18:00 M - F (I guess weekends are disabled) then you can use the following query by opening the Exporer of data link in the filing of your tools and selecting view | Query Builder:
UPDATE NotificationRule
SET DlvruleSchedule = "1f06001800".
The '1f06001800' means Monday to Friday from 06:00 to 18:00 - if you need every 7 days I can get this string instead.
This will update all devices notified for everyone in all areas.
-
Shared key change in bulk for the customers of ACS 4.2.1
Hello
is it possible to change the secret key that is shared for all devices in bulk instead of return to each clients and hand over the keys in ACS 4.2.1?
Please let me know if is it possible to execute more quickly.
Thank you
Hi Nitin,
Well, if you have all the devices in a single NDG, then simply click on the NDG > downstairs, click on change the properties > enter the new secret key shared it and it will prevail there. Although if you click on any customer to AAA within this NDG, it will show the OLD shared secret key, but due to the presence of this feature, where the key of NDG always overwrites the AAA client, this will probably work for you.
If you are not convinced by the above suggestion and I really want to change the shared secret key and then let me know.
You use ACS SE or windows ACS. I'm assuming that you have ACS SE
Here you need a CSV file with the code for the action of some NAS and you should be able to synchronize the CSV with RDBMS for the database to help
version 4.2Code 224 - UPDATE_NAS
VN = AAA client name
V1 = IP address
V2 = shared secret key
V3 = vendor
Import RDBMS synchronization definition
http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/A_RDBMS.html#wp148322Action codes to change the Network Configuration
http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/A_RDBMS.html#wp78096HTH
Jousset
Note the useful posts ~
-
Hello, I am importing a group of photos first and I would like to change all their sizes to 20% or more. Is there a way to do this without going into each photo?
Thanks for the info.
Yes. The first photo, then select, click right, copy. Then, select all the other photos, right click, paste attributes.
It works with all the effects.
-
How to change in bulk output Board contact InDesign?
Hello
I'm really a beginner with InDesign and hope someone can help.
I need to create image contact sheets that fit into an existing InDesign template. I was able to create contacts boards via Bridge, but I don't like how they look on the page. They have boxes around them, and the images are not centered in the fields of the object.
"I'm looking for a solution to a.) Edit the script to somehow contact sheet, so it is not put there in the first place boxes and images at the time of the creation of the centres (but less know anything about script) or b.), I need to change the output.
Option B is not hard to do in theory - I "select all" and change the stroke to 0 and Center images. Fine for a single page. But "select all" seems to only select a spread at a time. I have 80 pages! How can I register my changes to all pages please? Edit individually each of the 40 "spreads" takes forever. Is there to apply the changes I did for all the pasta spread? I tried to make changes to the master page, but it is not translated down to the other pages.
Any help would be much appreciated.
Thank you.
The style of the object using a paragraph style for the control text attributes. Change the paragraph style.
-
Two things to look at. First of all, the machine you are using your base line to ensure that it is configured correctly and that all the settings that you want are set manually. Second, make sure your filter sampling is pulling back enough data. If you use the default filters for the registry, I think they'll only 3 levels deep. My suggestion would be to create your own custom for SNMP filter. It would be a collection filter registry start set path to HKLM\SYSTEM\CurrentControlSet\Services\SNMP and to the collect at the level I would have put to all the. Remember with the new filter and you should start to see all the parameters.
Regarding the change of in bulk, if you just add to an existing Setup or change existing settings that can be easily done through the console once you get the filters to work. If you have no parameters or completely change their I did it by exporting a well-known registry and then key to deploy using a remote control. I then clean goes back through the console to remove the old keys that are no longer needed. Another tip which may help to ensure that everything is gettting the right settings is to create groups of computers for the settings you want. So if you add a key, you can create a machine group of all systems that do not have the key.
-
ACS 5.3.40.1 bulk edit problem with certain attributes of WCS
Hello
I just wanted to import the attributes WCS GANYMEDE + superusers on ACS 5.3.40.1 via the new feature of change in bulk. If I have attributes of trye what follows and click on submit, my admin user is disconnected from the web GUI and the changes are not saved:
task13 = view alerts and events
task15 = delete and clear alerts
task16 = Pick and collect no alerts
task17 = Ack and alerts Unack
Seems to be a bug. Anyone confirm this?
Best regards
Dominic
This issue is not specific to the new feature of change in bulk and can occur when you add entries to the GUI
Question relates to the use of "alert" in custom attributes GANYMEDE +.
There is an open CDETS which is rated for an ACS 5.3 stamp
CSCtx18638 Failed to add attribute to shell custom with keyword alert
-
Bottleneck in bulk updates/inserts
I worked on doing updates in block and inserts through sqlapi ++ using a library of extention udpate in bulk developed internally long ago. The oracle database is. Inserts/changes in bulk are in batches of 50K. I am facing a problem of very specific performance with respect to these bulk operations.
The first batch of insert in block (50K records) is done within 3 seconds; While the next similar batch for bulk insert or update (50 files again) takes a second huge 373. 'Top' on a RHEL-AS-4 server using, I could see what the oracle process that includes all of the 373 secods for completion; so sqlapi ++ or the in-house name extension isn't the culprit.
The third batch of 50K records in the sequence take much longer (second 913). The time will increase exponentially; and it doesn't seem to be > all < model out of it.
Surprisingly, this is not consistent. On a good day, I have the second batch browsing in 3 seconds. All the documents intact and perfect without any kind of defect in the data. In fact, all of the following prizes would end in or about 3 seconds.
Even more surprising, if I truncate the table and begin the process, the problem will reappear. He would again begin taking 370-380 seconds for 2nd batch. Once again, if I had used "delete from ' query instead of 'truncate table' query to delete all records from the table, there is no problem!
So in short, I came to the conclusion that the bottleneck occurs when the table is truncated (or is created new), and not when all records are deleted using the query "delete from.
All guess why it could be produced? I admit that I am not very good in data bases, so any help would be much appreciated.
Thanks in advance.
-
Shreyasshreyas_kulkarni wrote:
Well, I ran the SPÖ in bulk a new with statspack snapshots before and after the operation. as suggested by Jonathan, used the old hash value (for the operation of your time UPDATING) of the statspack report for sql_id and prepare the execution plan. I could of course.
Then I recompiled the program to generate the behavior that is 'good '. has run the op in bulk, statspack report generated. and surprise... There is no UPDATE statement in the report. UPDATE was simply not fired by the server; While in the test program, the rows affected by UPDATE operations have been exactly the number of lines in input (which is just, according to the supplied input data). so now it seems that somehow the server decides not to trigger the UPDATE, but still (rightly) returns all the rows as rows affected.
While I understand that statspack report contains not all queries fired; If the correct entry, to INSERT to get me fired, is fed, the op of the INSERT, which takes considerably takes less time the UPDATE operation, finds its place in the report. so I think that in the case of UPDATE, the UPDATE query is not triggered, and so 'good' behavior reports 3 seconds, while 'bad' behavior that triggers the UPDATE reports 440 seconds.
PLAN_TABLE_OUTPUT ------------------------------------------------------------------------------------------------ SQL_ID b5s6vazhy5a1g, child number 0 ------------------------------------- UPDATE MDS_MemberRelationMap SET parentlevelid = :0,childlevelid = :1, childdimid = :2, childleveldimid = :3, parentleveldimid = :4 WHERE (parentmemberid = :5) AND (childmemberid = :6) AND (parentdimid = :7) Plan hash value: 4110530053 -------------------------------------------------------------------------------------------- | Id | Operation | Name | Rows | Bytes | Cost (%CPU)| Time | -------------------------------------------------------------------------------------------- | 0 | UPDATE STATEMENT | | | | 2 (100)| | | 1 | UPDATE | MDS_MEMBERRELATIONMAP | | | | | |* 2 | TABLE ACCESS FULL| MDS_MEMBERRELATIONMAP | 1 | 104 | 2 (0)| 00:00:01 | -------------------------------------------------------------------------------------------- Predicate Information (identified by operation id): --------------------------------------------------- 2 - filter(("PARENTMEMBERID"=TO_NUMBER(:5) AND "CHILDMEMBERID"=TO_NUMBER(:6) AND "PARENTDIMID"=TO_NUMBER(:7))) Note ----- - dynamic sampling used for this statement
It seems that I did not yet understand the logic of your 'server' process, but if this seems to be a reasonable explanation to you that, in the case of the 'good' performance update is not performed at all, then this might be the point.
But looking at the execution of the UPDATE plan you don't think it might be better to accomplish the UPDATE using an index? Is there an index on the parentmemberid columns, the childmemberid and the parentdimid of MDS_MEMBERRELATIONMAP?
Moreover, it seems that you have no statistics at all on the MDS_MEMBERRELATIONMAP table because the optimizer using dynamic sampling, which takes some time to run because the optimizer runs a query on your table using predicates to check the cardinality in the analysis of the declaration.
I already mentioned that the execution of a single update requires that an average of 22 000 block gets by executing the statspack report you posted previously. Which is probably due to the carried out full table scan. If the three predicates parentmemberid, the childmemberid and the parentdimid only identify a few rows (or may be even one), then it is probably much faster to have an index suitable for the execution of the update.
Kind regards
RandolfOracle related blog stuff:
http://Oracle-Randolf.blogspot.com/SQLTools ++ for Oracle (Open source Oracle GUI for Windows):
http://www.sqltools-plusplus.org:7676 /.
http://sourceforge.NET/projects/SQLT-pp/ -
Privilege in WLC management needs first 2.2
The word Hello,
After you install a Cisco first 2.2 and added several WLC, my client wants to just a reading only the first management. Then, when I added WLC I provided SNMP v3 RO and no username/password / activate telnet/SSH.
The problem is that my customer wants to manage guest users of premium, I have of course some write type of privilege is necessary. Changing SNMP of ro to RW would be enough? Or maybe I need to add a user/password / activate SSH/telnet to manage? Or maybe I'll be times RW SNMP and telnet/SSH?
Thank you very much!
David
Hi David,
most likely, you would need RW and ssh\telnet as well, but it depends on what type of operations, your guest user will have access to.
Thank you-
Alya
Ratings encourage contributors *.
-
Cisco ipsec Vpn connects but cannot communicate with lan
I have a version of cisco 1921 15.2 (4) M3 I install vpn ipsec and may have customers to connect but cannot ping anything inside. A glimpse of what could be wrong with my config would be greatly appreciated. I posted the configuration as well as running a few outings of ipsec. I also tried with multiple operating systems using cisco vpn client and shrewsoft. I am able to connect to the other VPN ipsec running 1921 both of these computers by using a client.
Thanks for any assistance
SH run
!
AAA new-model
!
!
AAA authentication login radius_auth local radius group
connection of AAA VPN_AUTHEN group local RADIUS authentication
AAA authorization network_vpn_author LAN
!
!
!
!
!
AAA - the id of the joint session
clock timezone PST - 8 0
clock to summer time recurring PST
!
no ip source route
decline of the IP options
IP cef
!
!
!
!
!
!
no ip bootp Server
no ip domain search
domain IP XXX.local
inspect the high IP 3000 max-incomplete
inspect the low IP 2800 max-incomplete
IP inspect a low minute 2800
IP inspect a high minute 3000
inspect the IP icmp SDM_LOW name
inspect the IP name SDM_LOW esmtp
inspect the tcp IP SDM_LOW name
inspect the IP udp SDM_LOW name
IP inspect name SDM_LOW ssh
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-2909270577
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2909270577
revocation checking no
rsakeypair TP-self-signed-2909270577
!
!
TP-self-signed-2909270577 crypto pki certificate chain
certificate self-signed 01
license udi pid CISCO1921/K9 sn FTX1715818R
!
!
Archives
The config log
Enable logging
size of logging 1000
notify the contenttype in clear syslog
the ADMIN_HOSTS object-group network
71.X.X.X 71.X.X.X range
!
name of user name1 secret privilege 15 4 XXXXXXX!
redundancy
!
!
!
!
!
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
property intellectual ssh event logging
property intellectual ssh version 2
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group roaming_vpn
key XXXXX
DNS 192.168.10.10 10.1.1.1
XXX.local field
pool VPN_POOL_1
ACL client_vpn_traffic
netmask 255.255.255.0
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
tunnel mode
!
!
!
crypto dynamic-map VPN_DYNMAP_1 1
Set the security association idle time 1800
game of transformation-ESP-3DES-SHA
market arriere-route
!
!
list of authentication of card crypto SDM_CMAP_1 client VPN_AUTHEN
map SDM_CMAP_1 isakmp authorization list network_vpn_author crypto
client configuration address map SDM_CMAP_1 crypto answer
map SDM_CMAP_1 65535-isakmp dynamic VPN_DYNMAP_1 ipsec crypto
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
IP 76.W.E.R 255.255.255.248
IP access-group ATT_Outside_In in
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the SDM_LOW over IP
IP virtual-reassembly in
load-interval 30
automatic duplex
automatic speed
No cdp enable
No mop enabled
map SDM_CMAP_1 crypto
!
interface GigabitEthernet0/1
no ip address
load-interval 30
automatic duplex
automatic speed
!
interface GigabitEthernet0/1.10
encapsulation dot1Q 1 native
IP 192.168.10.1 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
property intellectual accounting-access violations
IP nat inside
IP virtual-reassembly in
!
interface GigabitEthernet0/1.100
encapsulation dot1Q 100
10.1.1.254 IP address 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly in
!
interface GigabitEthernet0/1,200
encapsulation dot1Q 200
IP 10.1.2.254 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly in
IP tcp adjust-mss 1452
!
local IP VPN_POOL_1 192.168.168.193 pool 192.168.168.254
IP forward-Protocol ND
!
IP http server
IP http authentication aaa-authentication of connection ADMIN_AUTHEN
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source map route ATT_NAT_LIST interface GigabitEthernet0/0 overload
IP nat inside source static tcp 192.168.10.10 25 expandable 25 76.W.E.R
IP nat inside source static tcp 192.168.10.10 80 76.W.E.R 80 extensible
IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 443 443
IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 987 987
IP route 0.0.0.0 0.0.0.0 76.W.E.F
!
ATT_Outside_In extended IP access list
permit tcp object-group ADMIN_HOSTS any eq 22
allow any host 76.W.E.R eq www tcp
allow any host 76.W.E.R eq 443 tcp
allow 987 tcp any host 76.W.E.R eq
allow any host 76.W.E.R eq tcp smtp
permit any any icmp echo response
allow icmp a whole
allow udp any any eq isakmp
allow an esp
allow a whole ahp
permit any any eq non500-isakmp udp
deny ip 10.0.0.0 0.255.255.255 everything
deny ip 172.16.0.0 0.15.255.255 all
deny ip 192.168.0.0 0.0.255.255 everything
deny ip 127.0.0.0 0.255.255.255 everything
refuse the ip 255.255.255.255 host everything
refuse the host ip 0.0.0.0 everything
NAT_LIST extended IP access list
IP 10.1.0.0 allow 0.0.255.255 everything
permit ip 192.168.10.0 0.0.0.255 any
deny ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
refuse the 10.1.1.0 ip 0.0.0.255 192.168.168.192 0.0.0.63
deny ip 10.1.2.0 0.0.0.255 192.168.168.192 0.0.0.63
client_vpn_traffic extended IP access list
permit ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
ip licensing 10.1.1.0 0.0.0.255 192.168.168.192 0.0.0.63
IP 10.1.2.0 allow 0.0.0.255 10.1.1.0 0.0.0.255
!
radius of the IP source-interface GigabitEthernet0/1.10
Logging trap errors
logging source hostname id
logging source-interface GigabitEthernet0/1.10
!
ATT_NAT_LIST allowed 20 route map
corresponds to the IP NAT_LIST
is the interface GigabitEthernet0/0
!
!
SNMP-server community [email protected] / * /! s RO
Server enable SNMP traps snmp authentication linkdown, linkup warmstart cold start
Server enable SNMP traps vrrp
Server SNMP enable transceiver traps all the
Server enable SNMP traps ds1
Enable SNMP-Server intercepts the message-send-call failed remote server failure
Enable SNMP-Server intercepts ATS
Server enable SNMP traps eigrp
Server enable SNMP traps ospf-change of State
Enable SNMP-Server intercepts ospf errors
SNMP Server enable ospf retransmit traps
Server enable SNMP traps ospf lsa
Server enable SNMP traps ospf nssa-trans-changes state cisco-change specific
SNMP server activate interface specific cisco-ospf traps shamlink state change
SNMP Server enable neighbor traps cisco-specific ospf to the State shamlink change
Enable SNMP-Server intercepts specific to cisco ospf errors
SNMP server activate specific cisco ospf retransmit traps
Server enable SNMP traps ospf cisco specific lsa
SNMP server activate license traps
Server enable SNMP traps envmon
traps to enable SNMP-Server ethernet cfm cc mep-top low-mep Dispatcher loop config
Enable SNMP-Server intercepts ethernet cfm overlap missing mep mep-unknown service-up
Server enable SNMP traps auth framework sec-violation
Server enable SNMP traps c3g
entity-sensor threshold traps SNMP-server enable
Server enable SNMP traps adslline
Server enable SNMP traps vdsl2line
Server enable SNMP traps icsudsu
Server enable SNMP traps ISDN call-information
Server enable SNMP traps ISDN layer2
Server enable SNMP traps ISDN chan-not-available
Server enable SNMP traps ISDN ietf
Server enable SNMP traps ds0-busyout
Server enable SNMP traps ds1-loopback
SNMP-Server enable traps energywise
Server enable SNMP traps vstack
SNMP traps enable mac-notification server
Server enable SNMP traps bgp cbgp2
Enable SNMP-Server intercepts isis
Server enable SNMP traps ospfv3-change of State
Enable SNMP-Server intercepts ospfv3 errors
Server enable SNMP traps aaa_server
Server enable SNMP traps atm subif
Server enable SNMP traps cef resources-failure-change of State peer peer-fib-state-change inconsistency
Server enable SNMP traps memory bufferpeak
Server enable SNMP traps cnpd
Server enable SNMP traps config-copy
config SNMP-server enable traps
Server enable SNMP traps config-ctid
entity of traps activate SNMP Server
Server enable SNMP traps fru-ctrl
SNMP traps-policy resources enable server
Server SNMP enable traps-Manager of event
Server enable SNMP traps frames multi-links bundle-incompatibility
SNMP traps-frame relay enable server
Server enable SNMP traps subif frame relay
Server enable SNMP traps hsrp
Server enable SNMP traps ipmulticast
Server enable SNMP traps msdp
Server enable SNMP traps mvpn
Server enable SNMP traps PNDH nhs
Server enable SNMP traps PNDH nhc
Server enable SNMP traps PNDH PSN
Server enable SNMP traps PNDH exceeded quota
Server enable SNMP traps pim neighbor-rp-mapping-change invalid-pim-message of change
Server enable SNMP traps pppoe
Enable SNMP-server holds the CPU threshold
SNMP Server enable rsvp traps
Server enable SNMP traps syslog
Server enable SNMP traps l2tun session
Server enable SNMP traps l2tun pseudowire status
Server enable SNMP traps vtp
Enable SNMP-Server intercepts waas
Server enable SNMP traps ipsla
Server enable SNMP traps bfd
Server enable SNMP traps gdoi gm-early-registration
Server enable SNMP traps gdoi full-save-gm
Server enable SNMP traps gdoi gm-re-register
Server enable SNMP traps gdoi gm - generate a new key-rcvd
Server enable SNMP traps gdoi gm - generate a new key-fail
Server enable SNMP traps gdoi ks - generate a new key-pushed
Enable SNMP traps gdoi gm-incomplete-cfg Server
Enable SNMP-Server intercepts gdoi ks-No.-rsa-keys
Server enable SNMP traps gdoi ks-new-registration
Server enable SNMP traps gdoi ks-reg-complete
Enable SNMP-Server Firewall state of traps
SNMP-Server enable traps ike policy add
Enable SNMP-Server intercepts removal of ike policy
Enable SNMP-Server intercepts start ike tunnel
Enable SNMP-Server intercepts stop ike tunnel
SNMP server activate ipsec cryptomap add traps
SNMP server activate ipsec cryptomap remove traps
SNMP server activate ipsec cryptomap attach traps
SNMP server activate ipsec cryptomap detach traps
Server SNMP traps enable ipsec tunnel beginning
SNMP-Server enable traps stop ipsec tunnel
Enable SNMP-server holds too many associations of ipsec security
Enable SNMP-Server intercepts alarm ethernet cfm
Enable SNMP-Server intercepts rf
Server enable SNMP traps vrfmib vrf - up low-vrf vnet-trunk-up low-trunk-vnet
Server RADIUS dead-criteria life 2
RADIUS-server host 192.168.10.10
Server RADIUS 2 timeout
Server RADIUS XXXXXXX key
!
!
!
control plan
!
!Line con 0
privilege level 15
connection of authentication radius_auth
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
connection of authentication radius_auth
entry ssh transport
line vty 5 15
privilege level 15
connection of authentication radius_auth
entry ssh transport
!
Scheduler allocate 20000 1000
NTP-Calendar Update
Server NTP 192.168.10.10
NTP 64.250.229.100 Server
!
endRouter ipsec crypto #sh her
Interface: GigabitEthernet0/0
Tag crypto map: SDM_CMAP_1, local addr 76.W.E.Rprotégé of the vrf: (none)
local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.168.213/255.255.255.255/0/0)
current_peer 75.X.X.X port 2642
LICENCE, flags is {}
#pkts program: 1953, #pkts encrypt: 1953, #pkts digest: 1953
#pkts decaps: 1963, #pkts decrypt: 1963, #pkts check: 1963
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 76.W.E.R, remote Start crypto. : 75.X.X.X
Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0
current outbound SPI: 0x5D423270 (1564619376)
PFS (Y/N): N, Diffie-Hellman group: noSAS of the esp on arrival:
SPI: 0x2A5177DD (709982173)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel UDP-program}
Conn ID: 2115, flow_id: VPN:115 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4301748/2809)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE (ACTIVE)the arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0x5D423270 (1564619376)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel UDP-program}
Conn ID: 2116, flow_id: VPN:116 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4301637/2809)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE (ACTIVE)outgoing ah sas:
outgoing CFP sas:
Routing crypto isakmp #sh its
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
76.W.E.R 75.X.X.X QM_IDLE 1055 ACTIVEIPv6 Crypto ISAKMP Security Association
In your acl, nat, you will need to refuse your VPN traffic before you allow the subnet at all. Just put all the declarations of refusal before the declarations of licence.
Sent by Cisco Support technique iPhone App
-
EVC problem and second-differently.
Hi all
I am trying to configure an interface with two tags dot1q but I can't do it.
I think that is because my line card does not support it, but I can't find any doc to confirm.
I have a 7606-S chassis with two WS-SUP32-GE-3 b, a WS - X 6548-RJ-45 and a WS-X6516A-GBIC.
When I try to configure a subinterface in any module with the command line "encapsulation dot1Q second-differently XY" router does not accept dot1q-deuxieme part of the order.
Router (config-subif) #do sh run the interface GigabitEthernet2/1.2
Building configuration...Current configuration: 38 bytes
!
interface GigabitEthernet2/1.2
endRouter (config-subif) #interface GigabitEthernet2/1.2
Router (config-subif) #encapsulation dot1Q 3?
native make as vlan native
I tried in an interface of each module and is always the same result.
After, I tried to use the service instance but I can not put encasulation under the part of service instance configuration.
Router (config) #interface GigabitEthernet6/5
Router(Config-if) #service instance 1 ethernet
Router(Config-if-SRV) #?
Controls configuration Ethernet EFP:
the default one order default values
specific description of Service instance description
Ethernet ethernet
exit out of the configuration of ETHER VET mode
IPv6 IPv6 interface subcommands
Mac commands for features based on MAC addresses
without denying a command or set its default settings
stop take the Service Instance, out-of-Service
instance of the SNMP service settings change SNMPThe easy way is upgrading hardware but is not a choice now...
Anyone know if it is possible to do with my hardware config?
Thanks in advance.
David.
Hello.
Yes, this kind of MPLS configuration is compatible with the SIP400, ss20/ES40 LC, but ss20/40 requires SUP720, so SIP400 is your only choice.
If you configure xconnect to the title of the service instance, you must SIP400 V2 SPA; If you configure under subinterface-> just SIP400. In this case SIP400 is for LC clients.
You also have an option to configure xconnect under interface VLAN-> SIP400 should be facing CORE LC.
-
Close all virtual machines on ESXi
Hello
I'm new in the administration of vSphere. I would like to raise our ESXi servers due to updates, but I've read that you shut down all virtual machines that are on it. You have something better to do then close VMs one? I expect a powershell script, but I have found none so far.
Thank you
Kralijir, you can do it from the console GUI.
In the left pane, select the ESX host.
In the right pane, click the tab "virtual machines". Now, you can select block all virtual machines here and simply right-clicking them stop all, or make other changes in bulk.
Some changes via selection bulk require all virtual machines to be in the same State; Turned off the power, power, etc.
If it works for you, please mark this answer as the 'response '.
-
How do you propose I have better import and modify many portions of old VHS?
I read the recent postings to the digitization of the multiple DVD and found it to be very interesting and informative. I searched in the archives, but did not run in an ad with exactly my question and I apologize because I know there must be others with the same question. That's what I have and want to do: Vista with an external Seagate attached via USB 2. I have Adobe Premier elements 3 but I am ready to buy another form of software and another form of external hard drive. I have a Firewire port.
I have a box of old VHS tapes of the recitals, dance my child, ball games, etc... the bands are very long, but often have only small portions of interest on them and now that my children are older, they are only interested in the 5 minutes of themselves. I would like to import the video and burn to dvd the relevant parts of the VHS.
I need to know both the equipment suggested to use to connect to the computer... what software I do you suggest that I use to edit images. Or maybe you have other suggestions.
I used the first a bit. I've never used huge files, like an endless dance recital so I hope you tell me there's a way that I could perhaps find a device that would allow me to view and scan only the parts that I want... or, perhaps, it would be best to take these tapes somewhere and have it make a DVD and then is there a way to import only part of them in this way? These are NOT videos of world class... (in fact, 20 years later I realize how much I was wasting my money! (HA!)
I have been clear in what I need and the kind of advice I ask?
Thanks for any advice you could offer me.
Here's what I did, more like an accident, rather than a process thought to spend a lot of money, or get the best possible quality when converting.
I had a bunch of old analog tapes, just like you and always thought that it would be very kool to get them in a format that I can use and load on my PC.
When I bought my DV Handycam, one of the options I was looking for was "Analog passthrough' capability. This basically allows connect an analog device such as a VCR and a video copy of your Handycam.
Office "DVD burners" usually have analog connections and can basically do the same thing.
With this feature, I then slowly went through the process of moving all my old recordings on my PC.
It did not work, yes he did.
Was it easy, Yes, it was (to the extent of the connection cable).
Has been tedious and a little of your time, Yes, Yes and Yes.
But over time I had all my old recordings on my PC and in a format that was initiated for the edition. (You can also make some changes in bulk to source the conversion).
With respect to the quality, whereas the video source and method of conversion, I was very happy with the end result and anyone who considers the clips (on PC or TV), has a hard time to see the differences between the final product and the source.
Would a dedicated HW device as Canopus gave better, most likely Yes, but in my case, the only time lets just move my tapes was not profitable. The purchase of a Cam with passthrough, or a DVD burner, works great and could be used for other things.
(One caveat, with Canopus or bridge HW configuration, the process is faster because it allows you to directly analog to DV - AVI. And DV - AVI is the goal of format for easy mounting with PE7).
A sure thing, my family and my friends get a hugh expel to see (because they are older in years).
And no one ever complains of the quality of the videos...
-
In APEX 4.0 application reports
Hello
I upgraded to the 4.0 APEX and really enjoy new features. The only feature that I used to use in 3.2 is the 'applications reports' under tasks.
It is mentioned in the help, but for the life of me I can't, someone else has it met?
Excerpt from the help file:
Access to the Bulk Edit point help report
To view the report in bulk point Edit help:
1. on the homepage of the workspace, click the icon of the Application Builder.
2. Select an application.
* 3. the list of tasks, click Application will appear
This is the part that isn't here
Any help would be appreciated.
Thank you
ConnorWe went all the reports and in bulk updates under the area they best fit. To change block aid, the page definition page, click on change all the icon, then on the utilities tab - you will see all the changes in bulk and special reports available for items. Same for the other types of objects. You can also get these utilities (new icon at the top right) page, in the right sidebar, you will find a list of all the utilities specific to the page.
Ditto for shared components, grid edit lovs is now a tab under lovs.
-Sharon
-
Change the settings of the BIOS on the Machines in bulk
I need to change the settings of the Legacy BIOS in the UEFI on machines in bulk instead of this manual, model lenovo is the E93Z, is there any kind of tool can do this in bulk or any mechanism
Please update me
There are utilities on the support site to allow the capture and playback of the BIOS settings.
Look at the BIOS of Windows configuration tool, it's readme file and instructions. Note it is strongly recommended that all systems be BIOS level. In addition, the tool requires the system used to capture the settings BIOS either the same version of bios the system in which you play their return.
Maybe you are looking for
-
How many movies high def. can fit on a 16GB USB DRIVE?
Hi all! I am a newbie with tech stuff, so please bear with me.I bought a Kogan STB with 1 TB PVR to record my Semi-HD TV HD movies. It is said to save, you must use a USB key. There is no internal hard drive. A good question here is to ask: "what do
-
Help! My office has win xp and moved stuff and somehow changed the display of the horizontal to vertical. How can I get that back? I currently have my flat screen sitting on his side arrrrrrrgggggg!
-
Pavilion 15: Windows 8.1 bluetooth does not not for HP pavillion 15
Hello... Recently upgraded to 8.1 windows and since then no bluetooth is detected in Device Manager. Help, please.
-
How to retrieve forgotten names of users and passwords for windows mail?
How to retrieve forgotten names of users and passwords for windows mail?
-
5.7 LR ceased to read NEF files
Recently, I upgraded my Lightroom 5 to 5.7 so that I could read my Nikon D750 NEF files. It worked great for a month, but yesterday, I tried to import my NEF files, and I got a message that LR could not read the files. can anyone help?