change the configuration of rman in Data Guard envrionemnt

Similar Questions

• ESXi 4.1 change the selection of trace on data warehouses

  ESXi 4.1, I have a couple of data warehouses that were not configured correctly. The selection of the path is set to fixed, while the other data stores have alternate-control storage IO. I'm looking for the less risky/disruptive way to change the configuration of these data stores. There are 15 ESX hosts.

  When to change the configuration of the data store is all for example conditions pre move VMs in another data store, stop the virtual machines etc.. Y at - it any disturbance to the ESX host?

  Hello

  Changing paths is not disruptive and can be done online, as long as takes care of the storage and SAN network is in good health.

  Validate it seems that some are on Round Robin and I presume that it is on the same storage array.

  You can do this by running a PowerCli script to modify the path selection: Home

  I don't have the scrip to activate SOIC

  Concerning

  Please allow points to useful/correct answers

• When I opened a NEW TAB, it loads 'Bing' - no matter what I try! especially to try to change the configuration settings

  Hello

  When I opened a NEW TAB, it loads 'Bing' - no matter what I try! especially to try to change the configuration settings!

  (Note I recently installed DivX player / converter / movies.. .is this the cause?)

  Then... on desktop... .double click on Mozilla... .loads ok
  Open a new tab..it loads Bing! & I hate it!

  Ive tried;

  1.Tools - options - addons - extensions & plugins - cant see anything there?
  2. On the small address bar (top right) which allows search engines to be managed - all cleared down except google & yahoo
  3. Tools - tab mix plus options - New Tabs - Load on new tabs set to Home Page (doesnt let me change it - greyed out url (conduit.com - see 5 below)
  4. Tools - tab mix plus options - New Tabs - Load on new tabs set to new tab Page - displays the url below (5) but if I try to edit it reverts back every time
  5. If I enter "about:config" & then "browser.newtab.url" in the URL bar I get
  
  browser.newtab.url;http://search.conduit.com/?ctid=CT3321897&octid=EB_ORIGINAL_CTID&SearchSource=69&CUI=&SSPV=&Lay=1&UM=5&UP=SP88BDE404-3DB6-49C4-97F5-96A64775CC57
  
  - rightclick on the selection and type 'reset' IT WONT CHANGE
  
  please can you help me?
  

  Thank you

  Stuart

  I see no mention of the duct. com in your initial post. It is often a good indication that you will taken place unwanted software.

• Can not change the configuration extreme airport

  Hello everyone, the community can maybe help me.

  I am a long-time Apple guy and can usually solve my own problems, but this one left me speechless. I have an Airport Extreme ages of less than 1 year. I set up OK and used for the last year. Now, I want to change the configuration. Specifically I add a port to the front, but I also had this problem, try to change the MAC address access lists, changing the wireless channel, allowing access as a guest, and probably any other change in config I try.

  Anyway, once I made the change, not restarting airport but then it fails to return to the top. The yellow light comes on and sometimes the utility Airport told me that he was unable to update the config. In this State I have to pull the plug to restart and once I did, the airport is back re-run without the changes I had made.

  It doesn't matter if I use the Airport 6.3.6 on El Capitan utility or Airport utility on iOS 9.2. The result is always the same. No change, fails to return to the top.

  I did a soft reset a hard reset and a factory reset. I've reconfigured from scratch (several times) and still can't seem to take a successful configuration change. I'm at the end of the ideas. I plan to return it because it's the year is February 2, but I don't want to go through the hassle if I can fix it myself or if it is a known problem that will not change with a change of equipment.

  In any case, here is specific information on the version by any chance, anyone else had this problem or knows a fix:

  Airport Extreme 802.11ac (ME918LL/A)

  Mac OS X 10.11.2

  Airport Utility 6.3.6

  iOS 9.2

  The actual configuration is crucial here.

  We need to know what is the brand and model of the modem?

  Some cable modems are at the origin of the terrible problems... especially the SB series cable modem.

  We should also see some screenshots of your configuration... Summary tab and network...

  We can work from there.

• USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

  USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

  Once again... Thanks for the tips...

• BES 5.0.3 api to change the configuration of account?

  Hello

  I want to temporarily disable the users to send and receive e-mail and messages on their devices.  What I've read, the way to do is to put "Redirect to BlackBerry" 'no' in the account configuration.  The problem I have is that I want to do from a Java application using the BES 5.0.3 Service Web interface and I can't find any way to do this.

  Can I retrieve the current value of the object AccountConfiguration and I see that it has a setter, but what is the method in the BWS interface I would use to change the configuration on the server?  If this is not yet supported, or I forgot something?

  Thank you.

  Hi and welcome to the forums!

  Currently, this feature is not supported. You can set e-mail filters or the folder redirection using BWS, but stop the flow of messages in total is not supported.

  Feel free to submit a request for this feature by using Issue Tracker (link in my signature). It is important when using file a new application to include a good deal.

  Kind regards

• What is the command to view the Configuration of RMAN

  What is the command to view the Configuration of RMAN

  in oracle 11g R2

  Hello

  You have to look in the documentation?

  The SHOW ALL command will show you the configuration. Is that what you're looking for?

• Oracle EBS: change the configuration of the new server

  Hello everyone.

  I'm newbie talk about administering Oracle EBS.

  This is the scenario:

  Oracle 11.1.0.7.0 database

  Oracle EBS 12.1.3

  The single node configuration: database of the layer and the application layer runs on the same server.

  OS: RHEL 5.7

  Virtual server.

  The IT guys have cloned the production server by using the virtual server administration software in order to create a new virtual server for development purposes. The production server has been cloned successfully, the new development server is a host name and IP address different of the production server.

  The head of the computer SCIENCE Department has asked me to work in the new development server. My goal is to change the configuration of the EBS:

  1. change the ORACLE_SID of the Oracle database.

  2. change the ORACLE_HOME of Oracle database and Applications: for example, current ORACLE_HOME is/U01/production and we need the ORACLE_HOME under/u01/development

  3. change the user and group of the owners of Oracle database and Applications directories: for example, current owner of the directories of Oracle database is oramgr user and need to change the owner of oradev user, same case for Applications: current owner of inventories of Applications is user applmgr and need to change the owner of appldev user.

  Of course, it is expected after making changes, the Oracle DB and Oracle Applications must be able to function normally, I want to use the scripts to start and stop oracle the bleachers.

  Is it possible to make the mentioned changes?

  Can you please guide me to do this?

  Thanks in advance guys!

  You will need to follow the steps of the R12 cloning MOS 406982.1 Doc - essentially you are going to use the current instance as the source and make a clone with all the necessary changes you listed, and then drop the source instance

• My Lightroom has lost the connection to most of my photos, records and collections. They are still on the computer. It happened, while moving my laptop when it was running. The mouse is moved and it might have changed the configuration. How can I do my wo

  My Lightroom has lost the connection to most of my photos, records and collections. They are still on the computer. It happened, while moving my laptop when it was running. The mouse is moved and it might have changed the configuration. How can I make my Lightroom works properly again?

  I use Lightroom 6.4 on a Pc with Windows 10.

  Has disappeared? Try file-> open the new item, and then select each illustrated catalog until you find the catalog with your photos.

  If this does not work, please post a screenshot of the problem.

• New router - how to change the configuration?

  I installed a new router but don't have my installation CD for my printer Photosmart 4385.  How can I change the configuration of my network without the CD?   I downloaded the drivers and software site HPO installation, but when I ran the installer, it never asked anything on the network.

  When you start the software, make sure that the printer is not connected to your computer via USB.  Then it should ask if you want to create a USB installation or network.

  If this isn't the case, you downloaded the software "full"?  Do this.

• Change the configuration of the built-in VNC server

  I'm experimenting with a code where I want to spend the VNC server inside the workstation 7.1.2 via the VIX API by writing to the runtime configuration variables. Just now using vmrun to do that, but doesn't seem to work. So the commands are:

  vmrun writeVariable runtimeConfig RemoteDisplay.vnc.port 5900

  These back via the command readVariable reading shows that they have been properly defined. However before you use VNC viewer to connect to localhost:5900 port fails. On the other hand if I enable it in the comments running via the settings dialog box, I am able to connect to the host via VNC.

  Is this a bug, wrong orders or simply not taken care of?

  Hi DaveP,

  I think that would fall under "not supported" for now.

  In my view, the component of VNC server of the running virtual machine process reads these configuration values only when the process starts up (so when you turn on or resume the virtual machine) and then is configured correctly. He will not change his report based on these being defined via vmrun (values are basically just put in a database in memory, there is nothing to say the re component - check the values once you make those calls).

  Basically, the VNC server cannot be configured (enabled or disabled) when running. You will need to power off the virtual machine, change the configuration file and power then turn it back on.

  OK, that last paragraph is not really true, since you can configure the runtime through the user interface. But, it is true, then it's vmrun or VIX. So, the primary response is the same: 'not supported '.

  Post edited by: mattrich

• You cannot change the format of RMAN backup

  Hello!

  I am trying to restore a backup of the database controlfiles in a new host solaris11 with RMAN in oracle 10 g. I have a solaris10 box where I installed database10g. As far as I know what I have to do is this:

  > define the dbid = 718308982;

  > startup nomount;

  > set controlfile autobackup format of disc type of the device of ' / u01/app/oradata/ACBET/%F';

  > Restore controlfile autobackup.

  However when I try to change the format, nothing happens.

  RMAN > set controlfile autobackup format of disc type of the device of ' / u01/app/oradata/ACBET/%F';

  executing command: SET CONTROLFILE AUTOBACKUP FORMAT

  RMAN > show all.

  RMAN configuration parameters are:

  CONFIGURE REDUNDANCY 1 RETENTION STRATEGY; # by default

  CONFIGURE BACKUP OPTIMIZATION # by default

  SET UP DEFAULT DISK DEVICE TYPE; # by default

  CONFIGURE CONTROLFILE AUTOBACKUP # by default

  CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # default < = same configuration by default...

  SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default

  CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default

  CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default

  CONFIGURE MAXSETSIZE TO UNLIMITED; # by default

  CONFIGURE ENCRYPTION OF DATABASE # by default

  CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default

  CONFIGURE THE NONE ARCHIVELOG DELETION POLICY; # by default

  And when I try to do the restore command I get the following error:

  allocated channel: ORA_DISK_1

  channel ORA_DISK_1: sid = 1626 devtype = DISK

  field of recovery destination: / u01/app/oradata/ACBET/backup

  name of database (or unique name of database) used for research: ACBET

  channel ORA_DISK_1: no record not found in the recovery area

  channel ORA_DISK_1: looking for autobackup day: 20131115

  channel ORA_DISK_1: looking for autobackup day: 20131114

  channel ORA_DISK_1: looking for autobackup day: 20131113

  channel ORA_DISK_1: looking for autobackup day: 20131112

  channel ORA_DISK_1: looking for autobackup day: 20131111

  channel ORA_DISK_1: looking for autobackup day: 20131110

  channel ORA_DISK_1: looking for autobackup day: 20131109

  channel ORA_DISK_1: found no autobackup in 7 days

  RMAN-00571: ===========================================================

  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

  RMAN-00571: ===========================================================

  RMAN-03002: failure of the restore command at 11/15/2013 10:50:22

  RMAN-06172: no autobackup couldn't find or handle specified is not a valid copy or a piece

  It seems he's looking for in the right path of recovery of the area, but I don't know why it's a failure.

  Thank you in advance,

  Nock

  Hello world

  The problem with this restoration has been far from my knowledge. The real problem was that the backup files that they sent were made in a different boutien than the one I used in the new host. For the sake of those who find this post in the future, you can not use rman to make. Until the date of this post, he must either use a simple import/export (with pump data if you like) or using transportable tablespaces to move a database between the hosts with another platform.

  Thanks for all the help.

  Nock

• Change the value to trigger record data for 1 s sampling frequency of 50 KHz

  Hello

  I have a VI with NI9215 and cDAQ-9178 chassis hardware. The function of the VI came out an instruction to RS232 interface and record 1 second of data every time that the set point is changed.

  The procedure is

  (1) modify the policy to the flow regulator

  (2) wait 2 seconds.

  (3) record of 4 channels for one second to the sampling frequency of 50 KHz.

  At present, the problem is for the first edition of this program, two seconds (rather than) data was saved and corn, the error message 200279.

  

  II. I revised for the second edition of the structure of the producer and the consumer who can increase the speed of the buffer.

  The question is how to configure the trigger to start the backup of data and limit data save for one second whenever the set point value changes.

  

  (1) which edition is best for my application?

  (2) how to trigger the data record?

  (3) how to record only a second of data?

  I also checked this announcement and the elapsed time seems not to work for this case.

  Any help would be greatly appreciated!

  Melody

  Hello

  you have not used properly the nodes property.

  1. replace the case structure in the first loop, with DAQmx features, with a structure of the event. Change the event fires for a worth of control of the setpoint change.

  Edit: as stated in your first post, use the structure of the event, but put inside the while loop.

  2. DO NOT connect error output from the stop command property node. Replace it with a local variable for the stop button.

  Try these and let me know.

• Refresh the MV of standby Active Data Guard

  Is it possible to refresh a materialized view (quick or full) come from a standby database Active Data Guard open in read mode only w/apply?  Or can I just do the update of the primary?

  Hello mseberg,

  You made a very good point about the definition of a database of the READER.

  After you have answered, I found in MOS: create a distributed materialized view based on a master table on a database in read-only (Doc ID 276023.1)

  This explains that it is NOT possible to make a fast refresh of a database shall RO.  However, it *peut* be possible to do a complete refresh of a standby Number.  It depends on the query used to define the MV.  If the RDBMS Analyzer determines the MV is *able* to fast refresh (even if there may not need it right now), so you can't do a full refresh since the eve of the RO.  If the parser determines that the request is NOT able to fast refresh, then you can do a full refresh since the eve of the RO.  I tested this script on 11.2.0.3.8 and found to be true:

  CREATE THE MIMI MATERIALIZED VIEW. MV_TEST

  TABLESPACE USERS

  IMMEDIATE CONSTRUCTION

  COMPLETE REFRESH

  AS (SELECT * FROM TEST@MIMI_ROSTBY);

  ORA-16000: database opened for read-only access

  ORA-06512: at "SYS." DBMS_SNAPSHOT_UTL', line 364

  ORA-06512: at "SYS." DBMS_SNAPSHOT_UTL', line 446

  ORA-06512: at line 1

  Now, I've changed the MV query to use a 'one time' feature (ROWNUM), which causes the query become complex (not able to fast refresh).  I can now create a MV on the day before RO, because the query is no longer able to fast refresh and requires no registration on the eve of the RO:

  CREATE THE MIMI MATERIALIZED VIEW. MV_TEST

  TABLESPACE USERS

  IMMEDIATE CONSTRUCTION

  COMPLETE REFRESH

  AS (SELECT * FROM TEST@MIMI_ROSTBY WHERE ROWNUM > 0);

  Created.

• You cannot change the configuration of the host

  I have stop my vm which is on san emc readers and he zoned for a second esx server.

  When I scan I can see the disks but I do not see a data store. then I try to add storage, signature of Dungeon and he tells me "cannot change the host configuration.

  (1) what I do 2) I tried vmotion and it did not work

  What is happening in vCenter, correct?  I had this happen in beta.  Connect to your ESXi host and then 'add a storage '.