Channel between 3560 port s two orange lights

We have a port pagp channel set up between two 3560 switches.  One of the switches indicates the port channel in blocking for one of our virtual local networks and for these ports leds blink orange.  There is no duplex incompatibilities or speed.  The STP blocking the cause?

Hello!

Hmmm... I can't really guarantee you until you give us the show spanning-tree VLAN 7 output for two switches.

However, I'm almost certain that this is not a crucial problem which may have an impact on your network.

Kind regards!

Tags: Cisco Network

Similar Questions

  • If the two orange lights on my Satellite L755 Flash: what it means?

    I have a Toshiba Satellite L755 - 154 (PSK2YE). Recently, whenever I start a game top-resources (Train Simulator 2015), after about half an hour power and battery indicators will Flash orange. Some time after this, the laptop shuts down. What is going on?

    Thanks in advance

    Usually (2nd left) power led lights white when the computer is turned on.
    This indicator flashes orange (orange) when the laptop turns off mode 'sleep'.

    The battery indicator shows the battery charge status.
    White indicates that the battery is fully charged, orange (orange) indicates the battery is charging and flashing indicates low batteries.

    In my opinion, it looks like the laptop becoming sleep or shut down because the State of charge of the battery is low.

    On the other hand, it may be possible your laptop overheats due to unacceptable temperature levels. In this case the indicator DC IN would be orange flash and the laptop would be closed.

    This could also be the case as this occurs during the execution of a set of high performance.

    In case of high internal temperature, you should check if the vents and the vents are free of dust and of the cooling air could circulate properly.

  • my ipod does not turn. When I put on his orange light continues to blink.

    My Ipod shuffle is not coming. When I put on the pricing still show the orange light flashing continuously.

    Flashing light (by itself) does not indicate that a problem.  Blinking light means "do not disconnect - eject the iPod before disconnecting."  It shows there is a connection between the shuffle and computer data.

    Are you using a Mac or a Windows PC?  If Windows, which version (including 32-bit or 64-bit)?

    My Ipod shuffle is not coming.

    Don't know what that means...  The shuffle appears in iTunes when you connect?

  • Satellite M110 - Orange light flashes when I push the power button

    just before I managed based on the knock off my bed, on a glance the plug that goes into the computer look slightly bent and now when I try to turn it on, it does not work. even when it is plugged.

    An orange light is always flashing down the bottem when I press the button.

    So is this a problem computer or a power supply problem?

    Hi becks88,

    Sounds like a serious problem of material... You can start Notepad without AC/DC adapter or is the battery charging adapter?

    Try to delete also the adapter AC and the battery for an hour at least. Then reconnect the two and try to start the laptop.

    In the worst case you need professional help a :(authorized service provider

  • Satelite L775 used high power - orange light blinks 5 times

    Greetings,

    I bought my Toshiba Satelight new l775 7 months ago, it's so crazy. It used to be on, I use the laptop connected to the adapter 4 to 8 hours a day, then the laptop goes unused and unplugged for 16 to 20 hours a day.

    This is my 3rd phone, I know that I put more tension on the previous two (HP and Acer). I've never had a laptop go on me this quick, even this acer laptop $ 300 crossed more tension and never went out in the 15 months that I got it.

    My laptop backup is a HP of 4 years, I've had it for 4 years, its fell several times, used and abused still underway! I just had to level of ram and hard drive. But, this Toshiba! She was so beautiful when I saw him!

    I have never dropped it, never spilled something on it, so why she put me through that stress at a bad time?

    A bad time because even if I'm under warranty, I'm leaving on vacation in 2 days! I need it, I'm not trying to take my old HP that came out in 2008.

    I can't afford to send my Toshiba for 2 weeks, not immediately.

    Today, my anti-virus software was his typical scheduled scan, I didn't charge the laptop, because I was out of work, so when I leave the laptop gets used more and charged additionally. I look at the laptop and its judgment, I just thought, O... my battery died, I would plug in the adapter and do some reading. Nothing good happened. 8 hours later, I worked on it for more than 8 hours, I searched all over google, many forums, none of the following solutions worked for me.

    Disconnect the battery and press power for 30 seconds
    Unplug the adapter and press power for 30 seconds
    Disconnect the battery and the adapter and press power for 30 seconds

    (of course after the 30 sec thing, I tried turns on normally, with or without battery and power adapter).

    I pulled the little battery round, hard drive, memory sticks (even changed the 2 around and I tried each one solo) I tried without any ram. I unplugged all the excess material, the only extra things I had was my usb mouse, but I unplugged that, even pulled the CD-ROM drive.

    I removed all water-cooling, open the laptop to see if I saw something a coward, I don't see anything, the part where the adapter will seem a little loose, but it seems to go all the way and fine. I pushed hard and still nothing.

    One thing I will say... I read at least 8 other fairly new poster of Toshiba satellite owners with similar problems of their laptop does not turn on. This isn't a good glance, since this is the first product of Toshiba, that I bought it and it costs $500 more than my acer laptop which gave me no problem in my 15 months of owning...
    I'm not belittling Toshiba immediately, this problem might be a small question (I hope), I could be my fault, so I'm not belittling Toshiba again because I like a lot about this laptop, especially the graphics!

    Return to this topic after watching the discussions of people with similar problems, I noticed, nobody had the same exact problem I'm having. See most of the threads I have read, people would still get the orange light when the battery has been driven. I ONLY get the orange light when the battery is in the laptop. I try and power without the battery and nothing happens, no light flashes. Many other people were always other color lights or lights in different locations, my only light flashes 5 times, the second place left and is orange.

    The only light that blinked in the last 8 hours is the second light from the left (I think it's the power light) and it flashes orange or maybe its red light... but when I press the power (I tried holding, tapping, etc...) that the orange light blinks 5 times and stops, nothing happens I don't hear any readers of spinning, everything is just dead.

    Thanks for the time and help!

    Hi a8000

    Looks like you already tried all possible solutions
    The flashing light indicates that there is a possible hardware failure, but it is not possible to say what part is malfunctioning, it might be the motherboard
    However, the guarantee seems to be valid so don t waste time and report it to the service provider in your country, they should solve this Toshiba!

  • I have an AirPort Express 802.11n (I just got 1st generation) who does not appear in Airport utility? The Express flashes an orange light.

    I have an AirPort Express 802.11n (I just got 1st generation) who does not appear in Airport utility?

    The Express flashes an orange light.

    I tried to reset to factory by using a paperclip for a little more than 10 seconds (green LED flashes).

    The Express flashes a light - orange after the reboot - that seems normal to me.

    I use an iPad or MacBook Pro (without port cat 5) set up.

    I would like to extend my WiFi network and stream of music with it.

    Read the manual and did some research but I'm stuck.

    Thank you for taking the time to help...

    NOTE: I also have a second generation version which works very well.

    Let us first make sure that you really have a 1st Gen AirPort Express. To do this, look for the model number on the side of the Express. It is difficult to see, with grey lettering on a white background, but the number starts model with an 'A' followed by four digits.

    You do not want to see A1264... not A1084 and A1088.

    Share your findings.

  • P1102w: P1102w - orange light blinking - won't initialize

    My printer won't boot and the orange light blinks. I tried to uninstall and reinstall the printer driver and firmware.  It also shows 'it can run out of toner' when I know that it is not. Cannot print page of test or anything else that he does not communicate with the computer. Help!

    Hey @cbloom57,

    Welcome to the Forums of HP Support!

    I understand that you have an orange light flashing on your Laserjet P1102w printer range. I can help you with that.

    To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once it is, while the printer is on, remove the power cable at the back of the printer for one minute. If you still see a flashing light orange, then the printer is more likely to have a recoverable hardware problem. This document explains How to resolve error lights on the printer.

    Please let me know the results after following the above. If you are able to clear the blinking light, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  • Half of the blades fell when creating a new channel of uplink port?

    I have a pair of 6248UP fiber interconnection (A and B) with blade servers connected. The switch upstream is Nexus7k. Fabric A and B each right has now a channel of uplink port to the Nexus switch upstream. I add a new Nexus switch to connect to the interconnection of fiber. The plan is to have uplink some VIRTUAL networks for Nexus one pass and uplink some VIRTUAL to the second Nexus switch networks.

    After that I configured the new Nexus switch with a channel port (only allowing some VIRTUAL networks) and corresponding port created on fabric channel A and B, new ports-channels have increased. However, half of the blade servers were down after that. What could be the reasons for this problem? Is it because half of the blades have been pinned dynamically on the new channel port, but the new port-channel side Nexus allow only some VIRTUAL networks?

    Is there a way to configure the Channel ports on fiber to interconnect with only the trunk through some VIRTUAL networks? for traffic from the server would not be sent to the port-channel where VLAN server is not allowed?

    Thank you

    In general, all NICs for/vhba of a fabric are declining, if all uplinks of this fabric are declining.

    It's not clear to me, what you're trying to achieve?

    If you create a global VLAN (for the two fabrics), this vlan is automatically inserted in all dependent North trunk links, unless you configure a leaking installation

    (http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns224/ns944/white_paper_c11-692008.html)

    Create a new vlan on UCS requires of course also this vlan is created on the switch connection and vpc by default allows all the VLANS. Could it be, that the vlan not appeared on the switch and was therefore not upward on the trunk?

  • impossible to connect or reset orange light flashing

    I read 100 amber streetlights, but have not met my situation at the moment.

    Flashing orange light on my 1470 time capsule.

    It does not connect to utility

    It will not be reset in any shape

    It has been cleaned, its is not overheated, it has a lit solid when modem connection.

    I read the possible motives of questions but no connection I can't even help out at this stage.

    Very expensive paperweight?

    Thank you

    Matt

    Have you tried to use the reset on the back? I believe that the orange light is a configuration problem - I get on mine when the network has changed and there is a configuration problem.

    I used a soft reset, which resets the SSID or connects via a cable, and then allows me to run the utility to reset the configuration.

  • MacBook Pro (2014) does not charge despite an orange light when plugged

    Hello

    So my 2 year old Macbook Pro (retina) does not load when it is plugged in - spite, projecting the orange light. I have a battery (20%) and it is reduced whenever I use it and will be soon drained.

    Some of the things I've tried

    -Reset SMC - tried but no change after

    -When I use the mac when it is plugged in the battery icon in the top bar done see the support - but there is no increase in % of the battery. Continuous use it starts to fall.

    -During use (and what battery is plugged) - I checked the report system (about this Mac section) - in the energy sector - it is said does not charge (despite being connected, the orange light and the symbol in the top bar)

    What do you think guys that it is? MLB? Battery?

    What I have to replace or can it be fixed?

    If you have the Apple store, take the machine evaluation.  There is no charge for this, but you need an appointment.   The first thing I would check would be the cable.  You have another machine to test this with.

  • I have a solid orange light on airport extreme but everything is fully functional, suggestions?  I have reset it.  Thanks in advance.

    I have a solid orange light, but my base station is fully functional.  I have reset the modem, the base station and in airport utility.  Airport utility shows no problem so I don't know what to do now.  Any advice would be great, thank you in advance.

    Is this new? If this is not the case, is what model?

    A fixed orange should be a serious error condition. Looks like it was just connected wrongly and the LED is upside down.

    It changes colour during the start cycle?

    If it is in the care of warranty or apple take it back to apple for replacement. There is nothing you can do about it.

  • My Airport express has had a solid orange light for a week. How can I fix this?

    My Airport express has had a fixed Orange light on in for about a week. When I click on it it says "it was part of my network" and to "ensure that it is still in the range and plugged in an outlet."  I tried this - does not change. I unplugged the main base station and then plugged it in. It also did not work.

    My operating system is OS X 10.9.5

    Thanks for any help.

    Sorry, but you can't 'fix' it. A status LED light amber solid that would indicate a power or another failure of the base station. There is no serviceable parts by the user, that you can replace.

    If the product is less than 1 year, Apple will replace the unit for you... or... If you have AppleCare implemented on a registered product, the AirPort base station is covered up to 3 years from the date of purchase.

    If you have an Apple Store near you, take the base station for them. Otherwise, contact the Apple directly to http://www.apple.com/support/contact/ Support

  • 1st generation ATV dead. Orange light but no screen and no resetting of distance.  I tried direct connection to Mac and iTunes open and he's not here.  Is it possible to restore to the factory without screen or remote work

    1st generation Apple TV is dead. Orange light but no screen and no resetting of distance. I tried direct connection to Mac and iTunes open and he's not here. Is it possible to restore to the factory without screen or remote workin

    I guess you tried maintained low men together for about 6 seconds - silver 1 ATV that will restart to the diagnostic partition but who would rely on the hard disk is functional and if it was ok that wouldn't work with the logic board failure.

    I guess you have not fed and attempted to restart.

    In case your AppleTV think it is paired with another remote try Menu and left arrow for 6 seconds - the light now intervenes when you press the buttons on the remote?

    Also, it could be in the video mode bad - try Menu and upward arrow together for 6 CES switch video modes, but implies that he actually started OK.

  • F12 button orange light is on and cannot connect to internet

    Hello

    My son has a laptop HP Pavilion g6 which operates Windows 8.1

    Everything works fine up until yesterday, when the orange light on the f12 key came and laptop does not connect to the internet.  We cannot turn this light off.

    Any help would be grateful

    Thank you!

    Hello

    You have a few options in my opinion please try these steps can help you solve your problem.

    (1) disconnect the battery & adapter then press on & press and hold the power button for laptop for 30 seconds then switch on and check if the wireless led lights.

    (2) go to Device Manager then uninstall the drivers wireless network card and restart the device and check if the light is on.

    (3) Please update the Bios & Wireless driver from the HP website.

    (4) click on start search type Recovery Manager and then click on it once select Yes on user access control, and then select I need immediate help and then select driver and select request recovery driver wireless and install it and then restart the device.

    (5) If you are comfortable with reinstalling the wireless card that will be on the rear panel of your device you can try this steps as well.

    If you still have the same issue then you need to call HP tech support and get the replaced part.

  • Flashing Orange light - to the right of the SD/MMC slot

    Why an orange light flashes next to the slot SD/MMS?

    It looks like a coil or something. Just below it is a solid blue light that looks like a radio tower with curves on each side, as it is to show the power out of it. But the orange light flashes, I wonder about that. I never gave no notice to the frontcourt, but the cat was to stick to something and I went to look for, and it was the orange light flashes. I don't know if it was always there or what. This is on a HP Pavilion 500f about four years. Can you tell me what this means or if I need to do something? Thank you.

    Hello @allcolors,

    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

    I read your post about how you want to know what radio flashing orange light is on the front panel of your desktop computer, and I'd be happy to help you in this case!

    The blue light flashing on the front panel is light of wireless radio on your computer indicating a connection to your network, and the amber light indicates hard drive activity. I hope this helps!

    Best regards

Maybe you are looking for

  • Keyword shortcuts

    Hi all Finally, I discovered that pressing on makes it key option that work the keyword my shortcuts. What I want to know is: Is there a way just to press one key without the key option, as well as the opening? Is it possible to reject a photo and ma

  • Could someone help me with updates for Service Pack 1 x 86 (Windows XP)

    I use Service Pack 1 x 86 for the home edition DIRECTLY from a disk of friends hologram Anyone know of a Web page that microsoft hosting yet updates of March 31, 2003, to August 8, 2004 Please someone I like windows xp I have Windows 7 Ultimate editi

  • Windows Mail does not accept my user name or password

    sho error: 'pop.att.yahoo.com', server: 'pop.att.yahoo.com', Protocol: POP3, server response: '-ERR [AUTH] invalid username or password. (#YSH002)', port: 995, secure (SSL): Yes, Server error: 0x800CCC90, error number: 0x800CCC92ws upwards

  • ISDN bind-l3-Manager of ccm for the PRI is not taken in charge - MGCP Gateway

    Dear all, Ive tried to get my (Voice Gateway) VGW recorded with my CUCM_7.1 I must add ISDN bind-l3-Manager of ccm in my serial interface. BUT THIS COMMAND IS NOT SUPPORTED The only similar to this command is bind-l3 ISDN q931. I tried to change IOS

  • Please tell me I can collect Actionscript 2 tutorials

    Dear friends I have a very new to Action script 2. So I need some tutorials on Drag and drop for practicePlease help me soon. Thanks in advance