channel search

Similar Questions

• channel search and move decimal places

  Hello

  I'm writing the code looking for a fractional string in an array and convert MV V in order to be properly compared to the other fractional numbers of string in the table.

  I have a chart that displays x iterations each with a column of minimum and maximum, including several types of decimal strings (negative/positive with several decimal places) each end with mV and V (example of a string:-725.543mV).

  Then, I divided the table in columns that contain the minimum and maximum values for each iteration. I want to compare the minimum values for each iteration and find the minimum, and do the same thing with the maximum values.

  Unfortunately, the way that I do, when I convert a fractional string numbering it removes label the unit V or mV but does not convert the number of mV V. so he compares - 725.543mV with - 52.334V as - 725.543 &-52.334, declaring the minimum value mV. I need the program to recognize that mV is less than V, or search in each table for the values marked with mV and move the decimal place is to the standard format of V.

  The unit label is actually a part of the string and not the screen (as you can see in the code that I have attached) and I understand that it is a little tricky in the way I need to do. But it's a dumbed down piece of code that I have possibly fit in my largest program that reads the values and their units of several different types of oscilloscopes. The laid out the values as strings as they appear on the screen and don't make the difference between mV and V unless they are asked for units that the tags right on the end of the output string.

  I'm sorry for the great post. SO to sum up, I need to find a table to ensure that all values have the same units, if they are not I need to convert each value of the unit appropriate, then output the max and min to the resulting table. my code is attached. Thank you for your help.

  

• Problem with channel search

  Hello

  My DB Version is 11.2.0.4.

  ICH have a column with the text less or more, and it should be possible to put all the lines that contain the key words in the search string.

  For example, the column contains the following text

  Maintenance for SVU-battery with NetConsult

  maintenance for USV battery NetConsult

  USV - battery with netconsult interview

  USV - battery with netconsult

  maintenance battery UPS

  maintenance battery NetConsult USV

  
  

  So if my searchstring is USV battery or maintenance USV battery NetConsult or maintenance for SVU-battery with NetConsult

  The result must contain all of the lines with the key words.

  
  

  All ideas are welcome.

  Certainly sounds like it would be a type of thing Oracle text.

  In regular SQL, assuming search keywords can be in any order and all search words must exist in the text resulting... something like...

  SQL > ed
  A written file afiedt.buf

  1 with t :) (txt)
  2 Select 'Maintenance for SVU - battery with NetConsult' of all the double union
  3 select 'maintenance for USV battery NetConsult' Union double all the
  4 Select 'maintenance for SVU - battery with netconsult' of all the double union
  5 Select 'USV - battery with netconsult' of all the double union
  6 select 'maintenance battery UPS' Union double all the
  7 select 'maintenance battery NetConsult SVU' double
  8         )
  9  --
  10 end of sample data
  11-
  12, s (ss) as long as)
  13. Select 'NetConsult USV battery' double
  14         )
  15-
  16 end of search criteria
  17-
  18, as t_words)
  19 select txt
  20, regexp_substr (txt,'[^-] +', 1, level) as t_word
  21 t
  where the 22 regexp_substr (txt,'[^-] +', 1, level) is not null
  23 connect by level<= regexp_count(txt,="" '[="">
  24 and txt = txt prior
  25 and prior sys_guid() is not null
  26         )
  27, s_words like)
  28 select regexp_substr (ss,'[^] +', 1, level) as s_word
  29 s
  30 connect by level<= regexp_count(ss,="" '="">
  31         )
  32-
  33 - end of data and search criteria split
  34-
  35 select txt
  36 from t_words
  37 join s_words (upper (s_words.s_word) = upper (t_words.t_word))
  38th group txt
  39 * having count (distinct t_word) > = (select count (distinct s_word) of s_words)
  SQL > /.
  TXT
  ---------------------------------------------
  Maintenance for SVU-battery with NetConsult
  USV - battery with netconsult
  maintenance battery NetConsult USV
  USV NetConsult battery maintenance
  USV - battery with netconsult interview

  5 selected lines.

  However, something like that would be really efficient on large amounts of text because of the amount of split that must take place.

• Get the channel search page numbers

  I've found that I can match a Word and get its page number by making a loop through the numPages, numWords using getNthWord, but I need to get a whole sentence like "api reference".

  The goal is that I need to extract some pages that contain certain phrases. My thought was to find, record page numbers, then extract and save.

  V7 + using all the search.query the search plugin (great search pane) and if you hover over every game it will tell you the page it's on, so I know the data is there. But after scouring the api, I can't seem to find something that could help.

  Here is my current idea, but as you can surmise for documents more large it takes a terrible time long:

  var extrList = [];
  searchIt ("indicate by check");
  App.Alert (extrList)

  
  function searchIt (srchStr) {}
  var ckWord, numWords;
  var tmpArr = srchStr.split("");
  var tmpArr.length = tmpLen;
  for (var i = 0; i < this.numPages; i ++) {}
  numWords = this.getPageNumWords (i);
  for (var j = 0; j < numWords; j ++) {}
  ckWord = this.getPageNthWord (i, j);
  for (var t = 1; t < tmpLen; t ++) {}
  If (j + tmpLen < numWords) {/ / check out of bounds}
  ckWord += "" + this.getPageNthWord (i, j + t)
  }
  }
  If (ckWord == srchStr) {}
  extrList.push (i)
  } / / end of equality so
  } / / end numword for
  } / / end numpage for
  }

  I guess my question is, is there a better approach for the search expression page numbers?

  Thank you.

  Can't answer your question directly, but I can tell you that it is possible

  use getNthWord to match a sentence. Basically, you need to do what you were doing

  so far (a double loop to find the first word in the sentence), then

  continue the corresponding words. If you match all of them, you can a

  positive match. It's complicated, but doable.

  For example, I just did that in this script, which highlights all instances

  of a word or phrase in a file:

  http://try67.blogspot.com/2008/11/Acrobat-highlight-all-instances-of.html

  Edit: Didn't see the code when I posted this... It seems that you got the hang of it.

  I don't know any other way to do this with a script.

• Can I use search or search to locate a comma or in quotes in a text

  I was wanting to use formulas to locate commas etc in text strings. I am new to mac and numbers and I can't find the right way to enter the channel search by searching for commas or quotes. Always get the message in invalid format.

  Is to FIND, like this:

  

  = FIND (",", A2)

  This shows that the comma is the 12th character in the string.

  This assumes that you are using. No, in your region as the decimal separator.

  If you use as the decimal separator so I think that the formula would be:

  = FIND(",";) A2)

  SG

• Toshiba L 39, 4333 - how to switch between ATV and DTV channels

  I really don't understand.

  During a search of channel, I chose to find DTV and ATV, and he finds DTV 13 and 42 channels ATV,
  I can see the two in a list of channels while I'm still inside the channel search menu.

  But when I press the OK button (to exit the channel search menu) I have only channels DTV or ATV, function I watch last before pressing OK button.

  Have you ever read the manual Toshiba s L 39, 4333?
  Here the manual in case you want to check: [Manual user s Toshiba L 39, 4333 | http://www.toshiba-om.net/LCD/PDF/English/L4333-323950-English.pdf]

  You can watch analog (ATV) or digital (DTV) antenna channels
  You can sort the channels for ATV or DTV, but as much as I know you cannot mix ATV and DTV
  So for both you will have separate channels lists

• get the number of wired physical channels?

  Hello

  I need to create a Subvi, and in this sub - VI, it is important to know the number of physical channels connected to the entrance of the Subvi.

  Is the only way to do than writing another "channel search and County" - Subvi, which examines the "physical" channels - wire? Something looking for a ': 'and',' and who treats this information then.

  Or is there a better way to do it?

  Or has someone already written such a Subvi, which counts the number of channels wired?

  Thank you very much

  Andy

  If you ask to know how many channels is in a physical channel DAQmx? If so, just the physical channel to Unflatten DAQmx channel chain wire. You'll get a table. The size of table function will give you the number of channels.

• Cannot get digital channels will appear on kdl-40xbr7 it worked last week.

  Since my grandchildren where here last week my TV KDL-40XBR7 only list digital channels. When you perform the initial installation, it finds all analog channels digital channel search starts it concludes digital a few then scanning stops at step 4 of 7 and shows the analog channels, but no. I tried everything even to put tv back to factory settings and install still no digital channels. Does anyone have an idea what could be wrong thank you.

  discovered step son plugged a device bundles and it corrupted digital firmware. I downloaded the firmware and loaded on the TV and everything works fine now.

• TouchSmart 520 TV tuner stopped working

  I have a 1190EA Touchsmart 520. I have recently upgraded to Windows 8 to 8.1 Windows and now the TV tuner stopped working. I've already used Windows Media Center to watch TV. I ran install MCE and windows MCE is unable to find all channels. My TV card is an Avermedia A859.

  I tried everything to fix the problem without success. I suspect that the card is is most recognized in the PC and have tried to find a driver windows 7 or 8 for the card A859. I was not able to locate a driver from the sites, including the Avermedia and HP. The only thing I could find is on the HP site where there is a patch TV card 'channel search fix' for Windows 7. I tried running it, but it returns a "HP not compatitibility" error message during the installation.

  I also tried to install other programs of TV tuner (no windows MCE) to see if these would work. These don't work and I think that they are not detect any signal. Yet once this leads me to think that the TV card needs a driver.

  If anyone can help here it would be really appreciated.

  Hey X 1199,.
  
  
  
  Tuner TV being not able to find any signal / channels, since the upgrade to Windows 8.1. After checking the HP Software and Driver download page, it takes up to 8 windows are supported. I've included the document 'what happens if I do not see my operating system?'. He will inform you of the various options you have.
  
  
  
  Now since you have tried to get the drivers from the manufacturer and 3 third-party sites and are still unable to get the job of TV tuner. You have options, restore your computer to the previous version. Or wait for the pilots to become available. I've included the document "performing a recovery of HP (Windows 8) system."
  
  
  
  Kind regards.

• Toshiba 40L3453DB - menu bar at the bottom of the screen empty

  Hello

  I have a Toshiba 40L3453DB tv and my bar menu at the bottom of the screen is empty.
  If I press the menu button i comes up with what is now and what next, then it just goes.

  I looked through all the settings to activate it, but I can't.
  Someone out there help me to activate this function.

  When I 1st installed 1 channel search time I think that I have turned it off.
  I tried the 1st time installation again to see if I can find, but it is not there.

  Help.

  Have you ever read the manual of L345 series?
  There you can find all details about the settings of the TV and features supported.
  http://www.Toshiba-OM.NET/LCD/PDF/English/Country_Specific/L3451-40-English-specific.PDF

  I assume you mean the information banner.
  See page 21

  If you press the "Info" button, the information on the screen will appear indicating the channel and the program being viewed. Each time change you channel, television displays the image spread along a banner of information at the bottom of the screen. It will remain on the screen for a few seconds.

  If the channel is locked, use the default 0000 PIN to unlock the channel.

  In the worst case if nothing will help get this banner working, reset the default TV.

• Satellite A660 - 14L - TV Tuner / TV-software

  Hello

  first of all, sorry for my bad English...

  Last week, I bought my 660 Satellite - 14L. I Replayced the original HDD with a SSD and installed a fresh Win7. Everything works fine, but I can't get the hybrid TV tuner to run.
  In the device manager card TV has been installed correctly, but I see no TV picture. I tried Winwos media center and a few other search software, google, but I tried all the software won't show me any TV Programm/image. For example: Windows Media Center runs a channel search, but no TV Signal has been found. the notebook-documentary says, no external antenna is necessary. But I have tried with and without external antenna. But nothing happens after the channel search.
  Then I tried to use the original HARD drive with pre-installed software Toshiba... but also the same thing... no TV signal.

  What am I wrong? Can someone help me or give me a hint, this software works very well with internal Toshiba TV hybrid Tuner. I live in Germany and I use DVB - T.
  Thanks for the help and thanks for reading my bad English.

  regrads kindly
  Olli

  Are you sure signal, DVB - T is available in your area where you live?

• How to identify the hardware CAN connected to the PC

  Hello

  Is it possible to identify the devices CAN to your PC via the USB port, I am able to see the name of material CAN logged in the Device Manager list. Even I want to read using LabVIEW.

  Regars

  Visuman

  Use of the vi in the zip file.

  And the "Devcon.exe" will show you the list of devices.

  With this list, you can sort the channel search on the EIB devices.

• "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".

  Original title: when setting up Windows Media Center, I get the error message: "IR hardware not detected".

  I have an internal TV Tuner that has been installed by HP, when I bought recently a "computer build-your-own." (According to the control panel Device Manager, my tuner is a Win TV HVR 1290, made by Hauppauge). The computer came with Windows 7. While installing Windows Media Center, after setting up the TV Signal (on channel 3) I am able to see a video thumbnail on my computer screen. I am also able to change the channel using my remote control U-Verse (not the Windows remote control supplied with the computer). So far so good! I then hit next and get the following message: "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".  After you receive this message, the installation procedure is completed. I called HP that support intalled the tuner. They had not the slightest idea what to do. I then called Hauppage customer (manufacturer of TV Tuner). They said that I need to plug one end of the IR Blaster cable that shipped with the computer in a slot in the back of my computer (they told me which slot). They said so to run the IR all the way cable to my cable box and the other end of the cable to my cable box of band. They said it was necessary to be able to use my Microsoft Remote to instruct the box to change channels (cable IR stuck on the box). I told her that I did not use the Microsoft Remote, I could change the channel with my U-verse remote (that I preferred to use anyway). He said that it took the cable on the band decoder in order to remove the error message and the installation of Windows Media Center. I then called U-Verse technical adapter who informed me of their set-top boxes (made by Cisco Systems) do not have the ability to receive signals IR IR Blaster cable (or any othe IR signal source). Microsoft is apparently not understand how U-Verse set-top boxes are designed to work and sells a product incompatible remote control/IR. My question is this: How do I set up Windows Media Center, in order to avoid getting the error message "IR hardware not detected" when you install Windows Media Center and just use the remote control of the U-Verse that I prefer to use in the first place. Once understand you this point, please send the information to HP, At & T U-Verse and others. Thank you.

  Ron, I have something for you!

  and for all the people who have this problem :)

  Hi, I had the time of IR not detected in Windows 7 Ultimate with a TV wonder 650 card and a box of digital adapter from Verizon for my PC... Go on the road to installation and after the Media Center channel search, choose manual configuration. Choose the aerial signal (I aso picked after this analog) l. After he sought more, he finds no channels.  Do not be afraid. Just accept it and go to the main settings page in the Mediacenter. If I remember correctly, then select TV Guide. Choose Add channel. I added the channel 3.

  Since my Verizon box has no IR for the computer, I added the channel 3 for the media Center and I change the channels with my Verizon remote. All my stations in the Verizon box go to Channel 3.

  The story here is so, for some reason any Windows detects that only my box channel signal TV and you must manually configure the media center on the air, then go to settings and add the channel you want in the guide.

  Why the guide TV control which channel you can tune is beyond me, but the scanner locks all channels, it does not detect. they must be added manually in the guide.

  My TV works and looks okay now.

  It actually works!

  the only problem is that it is not in HD

  but there is something

  
  

• Put a new background behind the hair

  Asked me to put a gray background dark behind this picture.  I am at a loss to know what to do with the spiky hair on the right side of his head where the background shows through. I can remove most of it but still remnants around the edges of the hair, creating a "glow".  Or, I have to go too, leaving tufts of hair, because the colors are so similar.  I have also tried new hair, new hair cloning paint and just can't get it to look right.  There are a few problems the other side of his head, but I managed to fix those through a combination of selection and removal removal of color for the background shine through and cloning. I will always be grateful for your help so I can finish this project!

  On a note related, once I have finally achieve this, what is the best way to "blend" the hair down, so it's not like I PLOPPED him on a new background? Thank you!

  Original image

  

  An attempt of edition.

  

  mmppgh430 wrote:

  I have already suggested, "It's impossible", but they want to coordinate with the pictures of other leaders of the organization.  So, unfortunately, they expect miracles.

  It is not impossible, but it takes time and skill to do with realism.  I would also say we really need a tablet like a Wacom, to do with any efficiency.  On the plus side, passing of bottom clear to dark, is much easier than the other way around.

  There are several ways to go about this, I recommend you follow several.  The secret to making any composite realistic is to work in layers using a variety of techniques.  Search on YouTube, there are many good tutorials.  I would do something like this:

  • First, I would try to get a good section, using layers of channel (search), and then select fast with a few feathers.  I'd probably also make two layers to allow the feathers to build.
  • Then I'd go closely and manually fade some of the mask, the places where there are gaps in the hair and what not.
  • Then I take a visible stamp on all sides of the hair and play with blend if (in the properties of the layer) and see if I could get rid of some of these spots of light, and play with a mixture of layers.  This layer is just going to add an additional definition where the hair is.
  • So I literally draw to hairs on the edge.  Just the sample of hair colors and draw little thin lines.  This is where you need the Wacom as you want the size and opacity to change.  This is by far the most time intensive, but it is also what separates composites you saw and you have not realized the trash you see on the internet.   Usually, I add layer effects, or the other highlight, shadow, or sometimes simply grit.  He adds a dimension to these flat lines.  Take it easy, does not take much.
  • Operating in several layers with hair, you can add and delete as you wish.  You need to add a Gaussian blur to make it look realistic, having a lot of layers allows different levels of blur.  Alternatively, you can add masks to discolor the hairs that are not good.
  • Then I'm going to literally paint on some of these strengths.  It's a dark background, so having a shadow around the edges will seem normal.  Once satisfied, I probably move this layer under the fake hair and adjust the fake hair, according to your needs.

  That's a lot, but it works if you take your time.  I'm not a pro, I am sure that those who have a much more simplified approach, but I found methods that work for me through play with different methods and stacking on the other.

• SQL to do a similar comparison against two concatenated columns...

  I'm doing a similar search against two columns that contain a first name, but people could touch as "John Doe"
  
  Can I do a similar search against concatenated columns?
  
  Kinda what I want to do...
  
  
  Select * FROM worker_view WHERE
  (LOWER (E.USUALFIRSTNAME) |) ' ' || Lower (E.LastName)) LIKE '% searchstring % '.
  
  
  ... but of course this isn't true... any direction would be appreciated!

  Let's take your example as test case

  First name: John
  First name: Doe

  Channel search possibilities:

  'John'
  'Doe'
  'John Doe'
  'Doe John'
  

  SQL statement:

  SELECT *
  FROM   worker_view
  WHERE  LOWER(E.USUALFIRSTNAME) LIKE LOWER('%searchstring%')
  OR     LOWER(E.LASTNAME) LIKE LOWER('%searchstring%')
  OR     LOWER(E.USUALFIRSTNAME) || ' ' || LOWER(E.LASTNAME) LOWER('%searchstring%')
  OR     LOWER(E.LASTNAME) || ' ' || LOWER(E.USUALFIRSTNAME) LOWER('%searchstring%')
  

  We'd still miss that follows:

  'JohnDoe'
  'DoeJohn'
  'John  Doe'
  'Doe  John'
  

  Hope that should be fine with your application.

  -dkv