Chromebook do not print

I have a P1102W with installing ePrint. My problem is it prints only about 50% of the time. It is connected to the network. It prints sometimes but just as often it will spend 1/3 of the way in which a page and then stops. The error light flashes. The only thing I could do is to turn off the printer and the new and then send the print job.

I just sent a page to the printer and it printed fine.

I then tried to send the same exact file to the printer with instructions to print 2 copies.

The printer ejected a page black and orange flashing began.

I had to turn off the printer and turn it on again the clear error flashing.

Tags: HP Printers

Similar Questions

  • I can not connect my chromebook to hp2840 printer?

    printer doesn't print even when I plugged in the cable and add a printer he doesn t work either any suggestions?

    Hello

    Chromebook does not print with a direct USB connection, for such a, you must configure the printer with the Google Cloud Print via another PC or Mac service.

    You can follow these steps to use your printer with a Chromebook:

    http://support.HP.com/us-en/document/c04127429

    Kind regards

    Shlomi

  • HP LaserJet Pro MFPm127fw: Printing Chromebook stuck in class and will not print

    My printer cannot print - things are still ongoing, but stay there for days until I delete them.  Everything is turned on and connected.  This printer has printed successfully for me before, but it goes through these phases where it stops printing and it has not printed for a week now.  I uninstalled, re-installed, all done.  My HP Chromebook detects the printer, shows pending print jobs, but they do not print.  Other aspects of the printer are very good, IE. Fax works.  I even don't try to use the email address to send documents to the printer... nothing works.

    I'd appreciate any help.

    Thank you

    Hello

    Please try to use printing HP extension for chrome to see if that helps. I've included below installation instructions.

    http://support.HP.com/RS-en/document/c04683559

  • Computer laptop Chromebook does not connect to the printer HP Officejet Pro 8610 range

    Hello! I have a few problems with the connection from my laptop to my printer to print documents!

    I have connected my printer to my wireless network, but do not understand how to connect my laptop to the printer!

    I don't have a disk drive with which use the installation disc in and the site that gave me to visit "hp.com/eprint/OJPro8610" shows me a 403 forbidden error message to ask. Can someone help me please? It is worth mentioning that I am not too good with computers, you may need to treat me like a little baby to make sure I know what you're talking about.

    My laptop is an Acer C720 Chromebook

    My printer is a HP Officejet Pro 8610

    Please hep me. Please, I beg you.

    Hello

    You need the following application:

    https://support.Google.com/chrome/answer/1069693?hl=en

    Please select the option #1

    Kind regards.

  • HP envy 4500 series: series like 4500 hp does not print

    printer prints test pages simply awesome.

    When I try to print, page comes out blank?

    Help, please

    Thank you

    John

    Hi @jsk4224,

    Thanks for joining the Forum from HP Support for a solution to your printing problem.

    I understand that you use a HP ENVY 4500 e-all-in-one printer with a Chromebook and and print pages of test very well but work sent from the Chromebook fate in white. I would like to help with that.

    Here is a support document which can help with this question - printer prints blank Page or fact not printing black or color ink.

    Please let me know if that solves the problem, or if you need assistance.
  • B211a model HP 6510: HP 6510 model B211a. Chromebook does not see it.

    Chromebook both HP are connected to the same system of wi - fi.  However, the chromebook does not recognize the printer.  The list shows the 6510 B211 is compatible, but makes no mention of the B211a (or b).  Is the compatible B211a or not?   If so, why can't my chromebook 'find '?

    Thanks for any help.

    Hello and welcome to the HP support community!

    Have you installed the print HP since the Chrome web app store?

    This article explains how to use it: http://support.hp.com/us-en/document/c04683559

    WyreNut

  • I can not print background images.

    I select print background images already. But I can not print background images yet. (mac firefox 19.0.2). Although I'm not this page (http://support.mozilla.org/en-US/kb/how-print-websites)
    Please advice me to [email protected]. Thank you.

    Same problem here. There was no picture printing problem until the upgrade. Now, they won't print and it's ruin how I run my entire business. Image logo printing on the packaging of the lists, codes bars printing of shipping labels. I deleted the cache and restarted. I also tried other browsers and is it not the problem.

    Any thoughts?

    Thank you!

  • A text on a page does not print

    On a number of pages, such as http://www.bbc.co.uk/radio4extra/programmes/schedules/2013/02/14 the text in purple - black prints. But black on the page text does not print.

    On the other hand, IE8 prints all text (in black)

    "This page uses a style sheet for what is in print - rel ="stylesheet"media ="print"href ="http://static.bbci.co.uk/programmes/2.51.1/style/print.css" "

    Maybe IE is not read this stylesheet even that Firefox reads this file for you. Although the Print Preview in Firefox and IE8 on my PC displays the same type of black and formatting. And this note is in this stylesheet - black print faster: sanbeiji.com/archives/95 -which explains why the print is black in Firefox (and IE8 for me).

  • Just connected my new imac on a HP printer previously attached to a Dell PC.  Printer works however, it will not print colour... ideas?

    Printer does not print the colors of my imac

    Make sure that you have installed the appropriate driver for your version of Mac OS X.

  • Epson effective 435 does not print in El Capitan?

    Hi, I have recently updated to EL Capitan and attempted to add epson Stylus 435 with no luck. The problem is that it appears in the list of printers so I choose what it but then under 'use', I try to look for the model but number 435 was not found. I only see epson 24 pins series and epson 9-pin. I tried both choices of 24 and 9 series. My mac connects to the printer, but does not print anything. There is nothing wrong with the printer because when I print from windows 7 is very good.

    I also tried to connect my mac to the printer via the usb port and it's exactly the same as above, it does not list my model.

    What should I do?

    When you connect to this model of Epson, by network or USB, you should get a prompt indicating that a driver is available at Apple and you want to download. Given that this is not happening (perhaps due to a previous version of the driver) then you can download and install the package of printer Epson v3.2 drivers from Apple and then you should be able to add your printer.

  • My Officejet 4620 do not print black ink

    I replaced the black cartridge on my Officejet 4620 with a new high-capacity HP cartridge and it won't print black ink on the test page, any application or function of Copier.  I have reset the printer nothing helps.  The ink level indicates that it recognizes the new cartridge and says it's full.  Black ink out of the cartridge when I put my finger against the exit hole.  I cleaned and aligned the print heads, but still no go.

    just in case someone else has this problem, heres whats really past and heres how to fix this annoying problem. its relatively easy to do and more efficient than wasting money on a new printer or have that he repaired as most people eventually do.

    going on what? the ink has clogged print heads and solidifies closed. the function of "clean print heads" the printer comes with doesn't have the ability to solve this problem. This feature is to clean the heads Sales, not clogged heads. Why hp decided to make this model without a simple to remove the cradle is beyond me, but fortunately the cradle out and can be cleaned with hot water.

    theres a few items, you will need to get there easily, or you could just burst the branch loppers, like I did and vent your frustrations.

    you will need: a pair of slender beak pliers, a screwdriver torx T9 (selling auto parts stores them for a few dollars), paper towels and a space for work (its easier to do this in a corner of a room, on a small table or floor).  Keep in mind that you are dealing with ink, then change your clothes right just in case and also catch a paper plate or a few sheets of paper to print to set ink cartridges while you work.

    (1) ok. lets start. !!! FIRST UNPLUG THE PRINTER RIGHT NOW, IF YOU DO NOT ACCIDENTALLY DIE BY ELECTROCUTION!  I forgot and when I started unscrewing the first 6 screws, kept chime jump and im like * beep *? I was impressed by the security measures hp took as model engineering.

    (2) the printer is now disconnected and then go to your corner your work surface and place the printer, so there is a wall or a barrier on the left, and also, a wall or a fence behind it. This just in front of her as if you were about to use it.

    (3) now, what you have to do, is to open the printer as you will change the ink and on the right side, there is a plastic guide that prevents opening all the way to the top. Look on the side and you'll notice that he could jump off with fingers. pop off and open it completely open, so you can get to the screws of the cover you would have prevented access to.

    (4) press the scanner part and the upper part against the back wall.

    (5) all the screws you will be remove are the size T9H torx screws. There are ten total. There are 2 black screws in the top of the forehead and then 4 black screws in the top of the back. Remove them and put them on your paper plate.

    (6) following is 1 screw silver short located under the Control Panel, use your finger and feel under the * button. Unscrew, place it on the paper plate.

    (7) depending on whether you want to remove the face/Control Panel to get in the last 3 screws so locate the illustrations on the top of the printer, there are 2 on the lower left and 5 at the bottom right (1 and 2 on the left explain removals of paper jam and 1-5 on the right then explain change in ink cartridges). then about half an inch South of the illustration of the number 5 on the lip, is a plastic stand. six inches to the left is an another then 6 inches to the left, under the number of the illustration 2 (remove the paper jam) is a third support. Unscrew using your nails. Flip it up just like the hood of the car, and eten on the main top of the printer, keep the flat wire which is connected to the frame of the control panel (if the flat wire jumped because you got too loud, then simply insert it in when you go back).

    (8) then unscrew the 3 long silver screws that are located under the Panel you just popped off the coast. There is 1 on the left and 2 on the side rightish. mix 'em on the paper plate.

    (9) now that all the screws are removed, take the Panel front and partially pop it back together.

    (10) then take all over (the part with the small illustrations and lift like a hood of car, ONLY THIS TIME OPEN IT LEFT and he balanced on the edge of the printer, to lean over towards the wall or an obstacle on your left.) MAKE SURE NOT TO PULL ON THE STRIP OF COLORFUL SON FRUITS LEFT AND ALSO THE FLAT BLACK WIRE CONNECTING PART SCANNING FOR THE MAIN OF THE PRINTER PART.

    (11) then take the pliers to tapered spout and remove the 2 silver tension springs located behind the printer cartridges. Pay attention to where they were attached so you remember where they go during the Assembly. take a picture with your phone if you have to, or simply re - understand it like I did. mix 'em on the paper plate.

    (12) then disconnect the 2 large flat wire and 1 small flatwire attached to the back of the ink cart. take a picture or can remember like I did. I guess bad things can happen if you reverse the on re-Assembly. Pick up the phone and take a picture of quik to be sure.

    (13) now remove the cart ink, cartridges and all, by lifting the front first.  Be careful of the transparent tape little there that moves the carriage from left to right and vice versa. you don't want to damage this little guy. now take the transport to your paper plate. not some ink or accidentally get it on your fingers without knowing or will make a mess.

    (14) remove the ink cartridges and put them on the paper plate, side ink to avoid a mess, these things sometimes drip. put the plate side. its time to clean the print heads.

    (15) then go to the sink, to the distribution of empty ink and turn on the hot water and then let the transport of empty ink sitting there with the water mainly through the clogged color screen (inspect and make you is not a small rubber seal surrounding the small screen, if there is do not waste it. I didn't look too closely and I don't think that hp has them but I have a few other printers). It will stain the sink but water ink he comes out to be sure. notice there is also a small circuit attached to it. don't bang it upward but getting wet does not matter.

    (16) continue to do this until the water is clear.

    (17) then use your finger and rub the screen gently with your finger and then rinse it, taking ink until the water is clear. This continues until there is no more ink and screens are clean. do it for all the colors just for good measures. the color of problem that would not print, you'll notice takes longer to clean than the other colors.

    (18) now look on the lower side of the transport. these strange looking things are the leaders. Rinse in hot water and dry them with paper towels. then flip it over and the breath on the side of the screen again. also between the screenside and heads (on the side of the transport) is an opening which is also probably gunked up. It blows with water too. Then, turn it over and wipe the head again. Repeat this step until no fades or until you are sick and tired.

    (19) shake, then use paper towels to dry the entire unit. Make sure that the device is dry.  especially inside the female plugs. blow inside or out dry hair and dry gently. do not stand there and melt the but with the blow dryer. but the sooner it dries less your ink cartridges, sitting on the paper plate will dry out. the custom of the ink dry quickly just do not take a NAP or go on a date until you're back with part of the ink.

    (20) now you have finished cleaning the heads and probably don't need to do it again for the length of time, it was because you bought the printer. and just as a roadtrip you used a map to navigate, you will use these instructions in reverse for reassembly. but keep in mind when re - insert the 3 flatwires that you disconnected from the back of the ink cart, make sure you that have small metal contact on the flatwires points (side male) inserted so they affect small metal contact points on the caps of transport (feminine) side. ALSO BE VERY CAREFUL NOT TO DAMAGE BLACK FLATWIRE CONNECTING THE SCANNER PART PART HAND PRINTER. THERE IS A SMALL GROOVE IN THE PLASTIC WHERE IT CAN SIT TO GUARANTEE NO CRIMPAGE. USE IT. also make sure that the 2 hinges to the scanner portion/cover are placed correctly before the fixing of the top with the 6 black screws.

    now raise the printer and reinstall the ink cartridges. then plug in the appliance and turn it on.  If you get notifications on the control panel telling the custom of transport move, then open the trunk and remove the ink cartridges, hustles and ensure that transport is installed and that the tensioner springs are in place correctly. Repeat the operation if necessary until notifications go away or just do a test print and do not take into account the notification if you messed with it a few times already. That's what happened to me and the notification went his own. Once its online, open the hp utility and press the button "clean the heads. do 2 x in a row and you will be in style, with colors extremely rich and "BOLD" and Yes, printed black raven.

    p. s.

    You can always take your aggression out with tree limb loppers or Tin shears like I did and cut the plastic Center keeps you to transport directly outside. Completely eliminates the disassembly and reassembly. Make sure you DO NOT CUT THE TRANSPARENT TAPE THAT MOVES BACK AND FORTH TRANSPORT. This way the next time it happens it takes you only 10 minutes before you are upward and printing.

    Enjoy!  -Porf

  • HP officejet: Hp officejet 4630 does not print

    I try to print a document from my computer and all I'm getting are dashes or white sheets. I've only used the pronter 4 times because I got it and 2 out of 4 times are to print or copy. There is ink in both cartridges so I don't know why, it's just Govind me white pages. I tried to clean the cartridges and to align it to see if it works, but the alignment page was not printed correctly. His lack of the printer image and most of the lines on who should be present. I know because I still had the first copy, when I did the alignment. I had this for less than a year and hardly used lrinter so I don't know why this isn't the impression that it should.

    Hello!
    Welcome to the HP community @Alewis324,

    I read your post on print quality issues you are facing with your Officejet 4630 and I wanted to answer with my suggestions for troubleshooting.

    Check out the links below and try the troubleshooting steps. If the quality does not improve, contact HP to discuss alternatives to the printer.

    1. Fixing poor print quality
    2. Printer prints a blank Page or doesn't print black or color ink

    If you have trouble, let me know and I'll do my best to help.

    Click on the thumb to below testify my help!
    Click on the 'accept as Solution' if I'm you guide to a solution!

    Best wishes

    HP technical support are available by clicking on the following link:

    http://h22207.www2.HP.com/us-en/?openCLC=true

    (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.

    (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.

    (3) Once finished, click the "Show Options" at the bottom right.

    (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

  • New Photosmart 5520 will not print in black

    I have a new HP Photosmart 5520 printer all-in-one.  Black ink ran out so I replaced it with a previously used ink cartridge which is of the same type # 564 but a XL version.  This cartridge has been barely used.  Now, I just can't get anything to print in black.  It will print in color, but not black.  I tried to turn off the printer.  I put the cartridge in my printer and it worked fine.  What should I do?

    edgarlogcabin wrote:

    my printer hp 5520 will not print black

    The in the here document troubleshooting steps may help resolve problems with black not not printing on your Photosmart 5520.  Especially make sure to check the events as on the Six Solution.

  • OfficeJet 4630: 4630 Officejet does not print

    My printer will not print, think that it is connected to a document that is displayed in the State feel that "suppression", but not go away?  The printer will copy ok and I can print a diagnostic page but it will not print any documents.  If I try, it goes into the queue but nothing happens?

    you use the printer wireless? in the affirmative.

    remove the printer in your queue and then turn on your printer > router > computer and then add the printer to the queue.

    If you use the printer with a cable remove printer > disconnect and reconnect the cable > add a printer

  • My HP Officejet 4500 printer all-in-one will not print web pages

    My new printer will not print anything when I try to print selections as a route on a web page of travel.
    Other features of the printer works k o such as print emails.
    I have Windows 7 Professional 64 bit system.

    "My new printer. »

    For a newly installed printer, you may need to reset some hidden preferences, print.print_printer, in particular, for Firefox to recognize the new printer.

    If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

    Not related to your question, but...

    You may need to update some plug-ins. Check your plug-ins and update if necessary:

Maybe you are looking for

  • How can I configure the ARD to work through the internet?

    Greetings and thanks in advance for any help provided. I hope that I didn't not lose only $ 80 million. I bought some ARD so that I can remotely access and help my father with questions as he uses his iMac. -(il est désormais impossible de l'aider pa

  • Finder keeps asking for password for the folder home page items

    Didier 10.10.5 on early 2008 Mac Pro Finder keeps askign my password even when you move to delete files on my office or home folder. Also not Save can open documents, as it says I don't have permission. have you tried disk since the start of the reco

  • Passwords and backup of the iPhone

    Until recently, I thought that this backup an iPhone to the computer via USB / iTunes / encryption was the only way to get passwords and other confidential data synchronized between the phone and my Mac. Isn't it true? I ask because I saw a piece on

  • How burncopy a DVD with one burner

    I have a computer with Windows Vista and a DVD burner. I would like to copy a DVD I have. I need to learn what to do so that I can share some important information with my neighbors. How can I do this?

  • Can I upgrade my hp dv7 graphics card a Nividia GeForce GTX 690?

    Hello. I currently have the HP dv7-3085dx entertainment laptop. I'm looking to make it a portable game. The games I want to perform are versions 3, Skyrim and Far Cry 3. I'm looking for a GeForce GTX 690 to replace my GeForce GT 230 m. I wanted to kn