Cisco ASA 5505 VPN L2TP cannot access the internal network
Hello
I'm trying to configure Cisco VPN L2TP to my office. After a successful login, I can't access the internal network.
Can you jhelp me to find the problem?
I have Cisco ASA:
within the network - 192.168.1.0
VPN - 192.168.168.0 network
I have the router to 192.168.1.2 and I cannot ping or access this router.
Here is my config:
ASA Version 8.4 (3)
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 198.X.X.A 255.255.255.248
!
passive FTP mode
permit same-security-traffic intra-interface
the net-all purpose network
subnet 0.0.0.0 0.0.0.0
network vpn_local object
192.168.168.0 subnet 255.255.255.0
network inside_nw object
subnet 192.168.1.0 255.255.255.0
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access deny ip any any newspaper
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool sales_addresses 192.168.168.1 - 192.168.168.254
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT dynamic interface of net-all source (indoor, outdoor)
NAT (inside, outside) source inside_nw destination inside_nw static static vpn_local vpn_local
NAT (exterior, Interior) source vpn_local destination vpn_local static static inside_nw inside_nw-route search
!
network vpn_local object
dynamic NAT interface (outdoors, outdoor)
network inside_nw object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 198.X.X.B 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
IKEv1 crypto ipsec transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac
transport in transform-set my-transform-set-ikev1 ikev1 crypto ipsec mode
Crypto-map Dynamics dyno 10 set transform-set my-transformation-set-ikev1 ikev1
card crypto 20-isakmp ipsec vpn Dynamics dyno
vpn outside crypto map interface
Crypto isakmp nat-traversal 3600
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 30
Console timeout 0
management-access inside
dhcpd address 192.168.1.5 - 192.168.1.132 inside
dhcpd dns 75.75.75.75 76.76.76.76 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal sales_policy group policy
attributes of the strategy of group sales_policy
Server DNS 75.75.75.75 value 76.76.76.76
Protocol-tunnel-VPN l2tp ipsec
user name-
user name-
attributes global-tunnel-group DefaultRAGroup
address sales_addresses pool
Group Policy - by default-sales_policy
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
tunnel-group DefaultRAGroup ppp-attributes
ms-chap-v2 authentication
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13
: end
Thanks for your help.
You must test with 'real' traffic on 192.168.1.2 and if you use ping, you must add icmp-inspection:
Policy-map global_policy
class inspection_default
inspect the icmp
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni
Tags: Cisco Security
Similar Questions
-
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK
I tried to set up a simple customer vpn using this document
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of VmHKIhnF4Gs5AWk3
VmHKIhnF4Gs5AWk3 encrypted passwd
hostname VOIPLABPIX
domain voicelab.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside 208.x.x.11 255.255.255.0
IP address inside 172.10.2.2 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool voicelabpool 172.10.3.100 - 172.10.3.254
history of PDM activate
ARP timeout 14400
NAT (inside) - 0 102 access list
Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1
Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 172.0.0.0 255.0.0.0 inside
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac
Crypto-map dynamic map2 10 set transform-set trmset1
map map1 10 ipsec-isakmp crypto dynamic map2
client authentication card crypto LOCAL map1
map1 outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 encryption aes-256
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address voicelabpool pool cuclab
vpngroup dns 204.x.x.10 Server cuclab
vpngroup cuclab by default-field voicelab.com
vpngroup split tunnel 101 cuclab
vpngroup idle 1800 cuclab-time
vpngroup password cuclab *.
Telnet timeout 5
SSH 208.x.x.11 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 172.10.1.2 255.255.255.255 inside
SSH timeout 60
Console timeout 0
username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2
Terminal width 80
Cryptochecksum:b03a349e1ac9e6022432523bbb54504b
: end
Try to turn on NAT - T
PIX (config) #isakmp nat-traversal 20
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1
HTH
-
ASA 5505 VPN established, cannot access inside the network
Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.
After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.
Here is my config:
ASA Version 8.2 (5)
!
hostname asa01
domain kevinasa01.net
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 5
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan5
No nameif
security-level 50
IP 172.16.1.1 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain kevinasa01.net
permit same-security-traffic intra-interface
Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (outside) 1 192.168.254.0 255.255.255.0
NAT (inside) 0 access-list sheep - in
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal Remote_Kevin group strategy
attributes of Group Policy Remote_Kevin
value of server DNS 192.168.1.12 192.168.1.13
VPN - connections 3
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
kevinasa01.NET value by default-field
username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
username kevin attributes
VPN-group-policy Remote_Kevin
type tunnel-group Remote_Kevin remote access
attributes global-tunnel-group Remote_Kevin
address-pool
Group Policy - by default-Remote_Kevin
IPSec-attributes tunnel-group Remote_Kevin
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
: endThank you
Hello
I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.
I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.
The acl must be:
sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
For nat (inside), you have 2 lines:
NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
NAT (inside) 1 0.0.0.0 0.0.0.0Why are you doing this nat (outside)?
NAT (outside) 1 192.168.254.0 255.255.255.0
Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)
Thank you.
PS: Please do not forget to rate and score as good response if this solves your problem.
-
ASA 5505 VPN remote cannot access with my local network
Hello guys, I have a problem with my asa 5505 remote VPN access to the local network, the VPn connection works well and connected, but the problem is that I can't reach my inside connection network of 192.168.30.x, here's my setup, please can you help me
ASA Version 8.2 (1)
!
!
interface Vlan1
nameif inside
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 155.155.155.10 255.255.255.0
!
interface Vlan5
No nameif
no level of security
no ip address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.240
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool vpn-pool 192.168.100.1 - 192.168.100.10 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
Mull strategy of Group internal
attributes of the Group mull strategy
Protocol-tunnel-VPN IPSec
username privilege 0 encrypted password eKJj9owsQwAIk6Cw xxx
VPN-group-policy Mull
type mull tunnel-group remote access
tunnel-group mull General attributes
address vpn-pool pool
Group Policy - by default-mull
Mull group tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Yes, you will need to either configure split tunnel so that internet traffic goes out through your local Internet service provider, GOLD / directed by configuration current you are tunneling all traffic (internet traffic Inc.) to the ASA, then you will need to create NAT for internet traffic.
To set up a tunnel from split:
split-acl access-list allowed 192.168.30.0 255.255.255.0
attributes of the Group mull strategy
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split-acl
I hope this helps.
-
Cannot access the internal network with Cisco easy vpn client RV320
I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?
Thank you
Hello
1. is the firewall on the active Windows 7 computer? If so, please disable it
2. can you check that you get a correct IP address in the range of the POOL of IP configured?
3. When you perform the tracert command to access an internal server, it crosses the VPN¨?
4. is the tunnel of split giving you access to internal IP subnets defined?
5. on the RV320 you see the user connected and sending and receiving bytes?
Don t forget to rate and score as correct the helpful post!
David Castro,
Kind regards
-
Cannot access the internal network of VPN with PIX 506th
Hello
I seem to have a problem with the configuration of my PIX. I ping the VPN client from the network in-house, but cannot cannot access all the resources of the vpn client. My running configuration is the following:
Building configuration...
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of N/JZnmeC2l5j3YTN
2KFQnbNIdI.2KYOU encrypted passwd
hostname SwantonFw2
domain name * *.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list outside_access_in allow icmp a whole
allow_ping list access permit icmp any any echo response
allow_ping list all permitted access all unreachable icmp
access-list allow_ping allow icmp all once exceed
the INSIDE-IN access list allow inside the interface tcp interface outside
list access to the INSIDE-IN permit udp any any eq field
list access to the INSIDE-IN permit tcp any any eq www
list access to the INSIDE-IN permit tcp any any eq ftp
list access to the INSIDE-IN permit icmp any any echo
the INSIDE-IN permit tcp access list everything all https eq
permit access ip 192.168.0.0 list inside_outbound_nat0_acl 255.255.255.0 192.168.240.0 255.255.255.0
swanton_splitTunnelAcl ip access list allow a whole
outside_cryptomap_dyn_20 ip access list allow any 192.168.240.0 255.255.255.0
no pager
Outside 1500 MTU
Within 1500 MTU
192.168.1.150 outside IP address 255.255.255.0
IP address inside 192.168.0.35 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP pool local VPN_Pool 192.168.240.1 - 192.168.240.254
location of PDM 0.0.0.0 255.255.255.0 outside
location of PDM 192.168.1.26 255.255.255.255 outside
location of PDM 192.168.240.0 255.255.255.0 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 192.168.0.0 255.255.255.0 0 0
Access-group outside_access_in in interface outside
group-access INTERIOR-IN in the interface inside
Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
client authentication card crypto outside_map LOCAL
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 20
encryption of ISAKMP policy 20
ISAKMP policy 20 md5 hash
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Swanton vpngroup address pool VPN_Pool
vpngroup swanton 192.168.1.1 dns server
vpngroup swanton splitting swanton_splitTunnelAcl tunnel
vpngroup idle 1800 swanton-time
swanton vpngroup password *.
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.0.36 - 192.168.0.254 inside
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
scott hwDnqhIenLiwIr9B of encrypted privilege 15 password username
username password encrypted ET3skotcnISwb3MV privilege 2 norm
username password tarmbrecht Zre8euXN6HxXaSdE encrypted privilege 2
username, password jlillevik 9JMTvNZm3dLhQM/W encrypted privilege 2
username privilege 15 encrypted password 49ikl05C8VE6k1jG ruralogic
username bzeiter 1XjpdpkwnSENzfQ0 encrypted password privilege 2
name of user mwalla encrypted password privilege 2 l5frk9obrNMGOiOD
username heavyfab1 6.yy0ys7BifWsa9k encrypted password privilege 2
username heavyfab3 6.yy0ys7BifWsa9k encrypted password privilege 2
username heavyfab2 6.yy0ys7BifWsa9k encrypted password privilege 2
username djet encrypted password privilege 2 wj13fSF4BPQzUzB8
username, password cmorgan y/NeUfNKehh/Vzj6 encrypted privilege 2
username password cmayfield Pe/felGx7VQ3I7ls encrypted privilege 2
username privilege 2 encrypted password zQEQceRITRrO4wJa jeffg
Terminal width 80
Cryptochecksum:9005f35a85fa5fe31dab579bbb1428c8
: end
[OK]
Any help will be greatly appreciated
BJ,
You try to access resources behind the inside interface network?
IP address inside 192.168.0.35 255.255.255.0
If so, please make the following changes:
1 SWANTON_VPN_SPLIT permit access ip 192.168.0.0 list 255.255.255.0 192.168.240.0 255.255.255.0
2-no vpngroup swanton splitting swanton_splitTunnelAcl tunnel
Swanton vpngroup split tunnel SWANTON_VPN_SPLIT
outside_cryptomap_dyn_20 3-no-list of ip access allowing any 192.168.240.0 255.255.255.0
4 - isakmp nat-traversal 30
Let me know how it goes.
Portu.
Please note all useful posts
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
The VPN Clients cannot access any internal address
Without a doubt need help from an expert on this one...
Attempting to define a client access on an ASA 5520 VPN that was used only as a
Firewall so far. The ASA has been recently updated to Version 7.2 (4).
Problem: Once connected, VPN client cannot access anything whatsoever. Client VPN cannot
ping any address on internal networks, or even the inside interface of the ASA.
(I hope) Relevant details:
(1) the tunnel seems to be upward. Customers are the authenticated by the SAA and
are able to connect.
(2) by many other related posts, I ran a ' sh crypto ipsec her "to see the output: it
appears that the packets are décapsulés and decrypted, but NOT encapsulated or
encrypted (see the output of "sh crypto ipsec his ' home).
(3) by the other related posts, we've added commands associated with inversion of NAT (crypto
ISAKMP nat-traversal 20
crypto ISAKMP ipsec-over-port tcp 10000). These were in fact absent from our
Configuration.
(4) we tried encapsulation TCP and UDP encapsulation with experimental client
profiles: same result in both cases.
(5) if I (attempt) ping to an internal IP address of the connected customer, the
real-time log entries ASA show the installation and dismantling of the ICMP requests to the
the inner target customer.
(6) the capture of packets to the internal address (one that we try to do a ping of the)
VPN client) shows that the ICMP request has been received and answered. (See attachment
shooting).
(7) our goal is to create about 10 VPN client of different profiles, each with
different combinations of access to the internal VLAN or DMZ VLAN. We do not have
preferences for the type of encryption or method, as long as it is safe and it works: that
said, do not hesitate to recommend a different approach altogether.
We have tried everything we can think of, so any help or advice would be greatly
Sanitized the ASA configuration is also attached.
appreciated!
Thank you!
It should be the last step :)
on 6509
IP route 172.16.100.0 255.255.255.0 172.16.20.2
and ASA
no road inside 172.16.40.0 255.255.255.0 172.16.20.2
-
Cisco ASA 5505 VPN passthrough
Hello
@home i'f installed a Cisco asa 5505 because the provider has the modem cable in transparent mode. So I have the public IP address to my firewall.
Also for the training because we have in the work of the asa. So I have no feeling with her.
but sometimes I have to build a VPN session to a server at work. But I do not get a connection to the server. If I remove the ASA 5505, then the connection to the server of work is great. But if to ASA 5505 is back in its place. It does not log VPN to the outside world.
Could someone point me in the right direction?
It is possible to create a connection out to the Cisco ASA5505 VPN.
Thanks in advance
Greetings
Palermo
Hi Palermo,
You do not have to mention the type of VPN connection, you use.
If the PPTP protocol then you need to inspect the traffic for the SAA allow again from 'outside '. Try the following:
! class-map inspection_default match default-inspection-traffic ! policy-map global_policy class inspection_default inspect pptp ! service-policy global_policy global !
see you soon,
SEB.
-
Cisco linksys router and cannot access the wireless network
We have cisco linksys wireless router. When we installed everything first, we could connect our wireless laptops to the network. Now, however, the network is detected, but there is no access to the internet. We have even a guy from ATT were out and he said that the wireless router has been installed backwards? He installed a dsl fast access on our laptop icon, and now we can access the wireless network but only if we connect as the first. We can also connect iPod to the wireless network. They detect the network, but when we enter the password cannot connect.
Hi JC_3094,
Welcome to the Microsoft Community and thanks for posting the question.
According to the description, it looks like you aren't able to access the Internet.
The likely causes of this problem is if the router is not configured properly.
Here are some steps that should help you to solve this problem.
Method 1:
Check if the router is configured properly to get access to the Internet.
Method 2:
Try the steps mentioned in this link and check:
This tutorial is designed to help you identify and solve problems with a wired (Ethernet) and wireless (Wi - Fi) network connections in Windows.
Wireless and wired network problemsMethod 3:If there is a frequent disconnection try to update the firmware on the router and check.In addition, visit these links for more information:Why can't I connect to the Internet?Hope this information helps. Respond us if you have any questions with windows and we will be happy to help. -
ASA 5505 VPN Site to site with several networks
Hello
I have a Cisco ASA 5505 configuration problem and hope you can help me.
Our company created a second facility, which must be connected using VPN to our headquarters.
I used the ASDM "Wizard of Site to site VPN" to create a connection, which works very well with our main network.
Following structure:
Headquarters:
Cisco ASA 5505, firmware 9.1, ASDM version 7.1
Outside: Fixed IP
Inside: IP address of the interface is 192.168.0.1/24 (data network)
Now I have a second network 192.168.1.0/24 (VoIP network), PBX address is 192.168.1.10.
The two networks should be accessible through the VPN.
New installation:
Cisco ASA 5505, firmware 9.1, ASDM version 7.1
Outside: Fixed IP
Inside: IP address of the interface is 192.168.2.1/24
I have already created a connection until a PC of the new plant reaches the data network. For example, a ping from 192.168.2.100 to 192.168.0.100 is possible.
Now, I want to add some VoIP phones to the new facility, which can reach the PBX on 192.168.1.10.
In the link, I have already added the two networks as remote network:
object-group network Testgroup network-object 192.168.0.0 255.255.255.0 network-object 192.168.1.0 255.255.255.0 access-list outside_cryptomap extended permit ip object-group Testgroup object Remote-Network
My problem now is, I don't know what to define as 'Bridge' on my PBX.
I can't use 192.168.0.1 because it's a different subnet. Also, I can not put a second IP 192.168.1.1 to the interface of the ASA.
You have any ideas, how can I accomplish this, so that the two subnets are accessed through the VPN and all devices have a defined gateway?
Could a "Easy VPN Remote" in "Network Mode" you help me?
What is the difference between 'Site-to-site' and 'extended network '?
Kind regards
Daniel condition, look for the solution GmbH
You can optionally configure a new LAN VIRTUAL (VLAN PBX) on the SAA and connect this interface to the voice network.
If you do not have a spare on the ASA port, then Yes, you have a router to route traffic from the PBX to the ASA via the data network.
-
Need help to access the internal network via VPN on ASA5505 8.4 (1)
Recently, I upgraded my ASA5055 from 8.02 to 8.4 and since I have updated to the new version I can access my home network is no longer through the VPN. I can connect to the VPN with no problems however I can no longer ping or you connect to my network of 10.0. Someone would be kind enough to look at my config and tell me what needs to be added to make it work? In my old config, I had a statement of NAT for VPN that is no longer here.
I also wanted to configure WebVPN to work as well, and this is something that I've never been able to understand. Is it also possible that I can be on my 20.0 network and connect to the VPN and access 10.0 as well? When it is connected to my network of 20.0 I'm not received credentials to connect to the VPN. I would be grateful if someone can help out me. The major part of this is the first part of this question.
My configuration:
ASA Version 8.4 (1)
!
ASA5505 hostname
domain xxxxxxxx.dyndns.org
enable encrypted password xxxxxxxxxxxx
xxxxxxxxxxxxxxx encrypted passwd
names of
nameserver 192.168.10.2
Office of name 192.168.10.3
name Canon 192.168.10.5
name 192.168.10.6 mvix
name 192.168.10.7 xbox
name 192.168.10.8 dvr
name 192.168.10.9 bluray
name 192.168.10.10 lcd
name 192.168.10.11 mp620
name 192.168.10.12 kayla
name 192.168.1.1 asa5505
name 192.168.1.2 ap1
name 192.168.10.4 mvix2
name 192.168.10.13 lcd2
name 192.168.10.14 dvr2
!
interface Vlan1
nameif management
security-level 100
IP address asa5505 255.255.255.248
management only
!
interface Vlan2
0050.8db6.8287 Mac address
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan10
nameif private
security-level 100
IP 192.168.10.1 255.255.255.224
!
interface Vlan20
nameif Public
security-level 100
IP 192.168.20.1 255.255.255.224
!
interface Ethernet0/0
Description pointing to WAN
switchport access vlan 2
!
interface Ethernet0/1
Uplink port Linksys 12 description
switchport access vlan 10
!
interface Ethernet0/2
Description Server 192.168.10.2/27
switchport access vlan 10
!
interface Ethernet0/3
Uplink Eth1 management description
!
interface Ethernet0/4
switchport access vlan 30
!
interface Ethernet0/5
switchport access vlan 30
!
interface Ethernet0/6
switchport access vlan 30
!
interface Ethernet0/7
Description of Cisco 1200 Access Point
switchport trunk allowed vlan 1,10,20
switchport trunk vlan 1 native
switchport mode trunk
!
Banner motd users only, all others must disconnect now!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain xxxxxxx.dyndns.org
network object obj - 192.168.50.0
192.168.50.0 subnet 255.255.255.0
Server network objects
host 192.168.10.2
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.224
network object obj - 192.168.20.0
subnet 192.168.20.0 255.255.255.224
network server-01 object
host 192.168.10.2
network server-02 object
host 192.168.10.2
xbox network object
Home 192.168.10.7
xbox-01 network object
Home 192.168.10.7
xbox-02 network object
Home 192.168.10.7
xbox-03 network object
Home 192.168.10.7
xbox-04 network object
Home 192.168.10.7
network server-03 object
host 192.168.10.2
network server-04 object
host 192.168.10.2
network server-05 object
host 192.168.10.2
Desktop Network object
host 192.168.10.3
kayla network object
Home 192.168.10.12
Home_VPN_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
outside_access_in list extended access permit tcp any any eq 3389
outside_access_in list extended access permit tcp any any eq 2325
outside_access_in list extended access permit tcp any eq ftp server object
outside_access_in list extended access permit tcp any any eq 5851
outside_access_in list extended access udp allowed any any eq 5850
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access udp allowed any any eq syslog
outside_access_in list extended access udp allowed any any eq 88
outside_access_in list extended access udp allowed any any eq 3074
outside_access_in list extended access permit tcp any any eq 3074
outside_access_in list extended access permit tcp any any eq field
outside_access_in list extended access udp allowed any any eq field
outside_access_in list extended access permitted tcp everything any https eq
outside_access_in list extended access permit tcp any eq ssh server object
outside_access_in list extended access permit tcp any any eq 2322
outside_access_in list extended access permit tcp any any eq 5900
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any any source-quench
outside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any one time exceed
outside_access_in list extended access udp allowed any any eq 5852
KaileY_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 36000
logging warnings put in buffered memory
recording of debug trap
asdm of logging of information
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of errors
Management Server host forest
MTU 1500 management
Outside 1500 MTU
MTU 1500 private
MTU 1500 Public
local pool IPPOOL 192.168.50.2 - 192.168.50.10 255.255.255.0 IP mask
local pool VPN_POOL 192.168.100.2 - 192.168.100.10 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ASDM image disk0: / asdm - 641.bin
don't allow no asdm history
ARP timeout 14400
!
Server network objects
NAT (private, foreign) static tcp ftp 5851 service interface
network object obj - 192.168.10.0
NAT (private, foreign) dynamic interface
network object obj - 192.168.20.0
NAT (outside) dynamic public interface
network server-01 object
NAT (private, outside) interface static 2325 2325 tcp service
network server-02 object
NAT (private, outside) interface static udp syslog syslog service
xbox network object
NAT (private, outside) interface static service udp 88 88
xbox-01 network object
NAT (private, outside) interface static service udp 3074-3074
xbox-02 network object
NAT (private, outside) interface static service tcp 3074-3074
xbox-03 network object
NAT (private, outside) interface static tcp domain domain service
xbox-04 network object
field of the udp NAT (private, foreign) of the static interface function
network server-03 object
NAT (private, outside) interface static tcp https https service
network server-04 object
Static NAT (private, outside) interface service tcp ssh 2322
network server-05 object
NAT (private, outside) interface static 5900 5900 tcp service
Desktop Network object
NAT (private, outside) interface static service tcp 3389 3389
kayla network object
NAT (private, outside) interface static service udp 5852 5852
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.248 management
redirect http outside 80
location of SNMP server on the Office floor
SNMP Server contact [email protected] / * /
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds
Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.248 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 30
access to administration management
dhcpd dns 24.205.1.14 66.215.64.14
dhcpd ping_timeout 750
dhcpd field xxxxxxxx.dyndns.org
dhcpd outside auto_config
!
dhcpd manage 192.168.1.4 - 192.168.1.5
dhcpd enable management
!
dhcpd address private 192.168.10.20 - 192.168.10.30
enable private dhcpd
!
dhcpd 192.168.20.2 public address - 192.168.20.30
dhcpd enable Public
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.43.244.18
Server NTP 129.6.15.28
WebVPN
internal Home_VPN group strategy
attributes of Group Policy Home_VPN
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol without ssl-client
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Home_VPN_splitTunnelAcl
value by default-field www.xxxxxx.com
the address value IPPOOL pools
WebVPN
the value of the URL - list ClientlessBookmark
political group internal kikou
group attributes political kikou
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list KaileY_splitTunnelAcl
XXXXXXX.dyndns.org value by default-field
username scottrog encrypted password privilege 0 xxxxxxxxxxxxxx
user_name john encrypted password privilege 0 xxxxxxxxxxxxxxx
username joek encrypted password privilege 0 xxxxxxxxxxxx
eostrike encrypted xxxxxxxxxxxx privilege 15 password username
username almostsi encrypted password privilege 0 xxxxxxxxxxxxxx
username ezdelarosa password xxxxxxxxxxxxxxencrypted privilege 0
type tunnel-group Home_VPN remote access
attributes global-tunnel-group Home_VPN
IPPOOL address pool
LOCAL authority-server-group
authorization-server-group (outside LOCAL)
Group Policy - by default-Home_VPN
authorization required
IPSec-attributes tunnel-group Home_VPN
IKEv1 pre-shared-key *.
type tunnel-group SSLClientProfile remote access
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
tunnel-group type ClientLESS remote access
tunnel-group kanazoé type remote access
attributes global-tunnel-group kanazoé
address VPN_POOL pool
by default-group-policy kikou
tunnel-group KaileY ipsec-attributes
IKEv1 pre-shared-key *.
by default-group Home_VPN tunnel-Group-map
!
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:438ed6084bb3dc956574b1ce83f52b86
: end
ASA5505 #.
Here are the declarations of NAT for your first question:
network object obj - 192.168.100.0
255.255.255.0 subnet 192.168.100.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.50.0 obj - 192.168.50.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
And 'clear xlate' after the above and that should fix your first question.
I would check your second question and get back to you shortly.
-
VPN ssl cannot access the internet
Hello guys!
I need help to allow access to the internet for my vpn users. I can connect with Anyconnect but do not have access to the internet. Subnet for VPN is 192.168.100.0. I welcomed this subnet on my cisco router.
ISP-> router-> 192.168.0.0-> ASA-> 192.168.1.0 (887VA)
Here is my config:
ASA Version 9.1 (3)
mask of local pool AnyConnect 192.168.100.1 - 192.168.100.254 IP 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search to itinerary
Trust SSL VPN outside
Trust SSL VPN inside
WebVPN
allow inside
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.04072-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
L2TP ipsec ikev2 VPN-tunnel-Protocol
internal GroupPolicy_VPN group strategy
attributes of Group Policy GroupPolicy_VPN
WINS server no
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
username alex Awards
VPN-group-policy GroupPolicy_VPN
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address pool AnyConnect
Group Policy - by default-GroupPolicy_VPN
VPN Tunnel-group webvpn-attributes
enable VPN group-alias
Thank you very much!
Hello
Make sure you have this configuration
permit same-security-traffic intra-interface
You can check with
See the race same-security-traffic
If you don't have it then add it and test again.
If this does not work after this then check if your router is to see all this traffic. For example you see any translation NAT on the router to your VPN users?
What NAT configuration did you use for testing? I suggest 2 options above.
First of all, one was to change the current VPN Client NAT0 configuration and dynamic addition PAT for VPN users to the Internet.
Second, it was just to change the configuration of NAT0
-Jouni
-
Cannot access the internal resources for VPN site-to-site
We have two ASA. We set up just VPN site-to-site. For some reason, we are not able to access internal resources at the main office of the remote office. Do you have any suggestions? Thank you.
as wu suggested, please first confirm that the tunnel is mounted correctly
"sh cry isa his '-> will tell u if the phase 1 is in place
"sh cry ips its '-> say if phase 2 is in place
now once they r upward, when you ping from site to site b
program in the site, you should see one and decaps site b for traffic from a to b and vice versa for return transportation
Now we have to see where it is a failure
could be tht package is coming up to the asa but not getting is not encrypted or that the package does not come to the asa itself
You can run tracer package to see if it's getting wrapped, or in other words hits vpn tunnel
It might be a nat problem, and sometimes if it is a new configuration probably ISP may have blocked the esp traffic in one direction or in the other direction
the best approach, that it is turn on "management of access to the inside" on the firewall and make a ping of source of asa
inside ping
Maybe you are looking for
-
Preview pane of mail suddenly disappeared
My preview pane of Mail suddenly disappeared and will not return. I tried all kinds of drag and switch between the 'Classic' provision and normal page and stop/restart implementation. None of these work. What has gone wrong?
-
Satellite P100-160: cooling fan comes loudly for 1-2 seconds every 30 seconds
I have Vista and I tried everything.I set the thermal control mode in the BIOS to "Silent" (although sometimes I look in the BIOS and it is up to the performance). I have disabled Aero, changed the minimum and maximum processor speed etc.. The irregu
-
How to turn the camera off when I get the picture?
How to turn the camera off when I get the picture? How to turn the camera off when I get the photo I do my iphone 6 mute and when I get the picture give sound
-
What fsx actually require as much as the frame per second rate?
With higher settings, I show that it is running only 20-30 fps. I thought it would be more. My system can handle more.
-
Boot MGR missing, Windows Vista,
Hey! so I have a Lenovo that runs on windows vista, and it had this nasty virus that I could only remove by resetting my computer back to factory settings (I saved most of my personal files) and if that wasn't bad enough, when I tried to restart my c