Cannot access the internal resources for VPN site-to-site

We have two ASA. We set up just VPN site-to-site. For some reason, we are not able to access internal resources at the main office of the remote office. Do you have any suggestions? Thank you.

as wu suggested, please first confirm that the tunnel is mounted correctly

"sh cry isa his '-> will tell u if the phase 1 is in place

"sh cry ips its '-> say if phase 2 is in place

now once they r upward, when you ping from site to site b

program in the site, you should see one and decaps site b for traffic from a to b and vice versa for return transportation

Now we have to see where it is a failure

could be tht package is coming up to the asa but not getting is not encrypted or that the package does not come to the asa itself

You can run tracer package to see if it's getting wrapped, or in other words hits vpn tunnel

It might be a nat problem, and sometimes if it is a new configuration probably ISP may have blocked the esp traffic in one direction or in the other direction

the best approach, that it is turn on "management of access to the inside" on the firewall and make a ping of source of asa

inside ping

Tags: Cisco Security

Similar Questions

Cannot access the internal network of VPN with PIX 506th

Hello

I seem to have a problem with the configuration of my PIX. I ping the VPN client from the network in-house, but cannot cannot access all the resources of the vpn client. My running configuration is the following:

Building configuration...

: Saved

:

6.3 (5) PIX version

interface ethernet0 car

Auto interface ethernet1

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

activate the encrypted password of N/JZnmeC2l5j3YTN

2KFQnbNIdI.2KYOU encrypted passwd

hostname SwantonFw2

domain name * *.com

fixup protocol dns-length maximum 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol 2000 skinny

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names of

access-list outside_access_in allow icmp a whole

allow_ping list access permit icmp any any echo response

allow_ping list all permitted access all unreachable icmp

access-list allow_ping allow icmp all once exceed

the INSIDE-IN access list allow inside the interface tcp interface outside

list access to the INSIDE-IN permit udp any any eq field

list access to the INSIDE-IN permit tcp any any eq www

list access to the INSIDE-IN permit tcp any any eq ftp

list access to the INSIDE-IN permit icmp any any echo

the INSIDE-IN permit tcp access list everything all https eq

permit access ip 192.168.0.0 list inside_outbound_nat0_acl 255.255.255.0 192.168.240.0 255.255.255.0

swanton_splitTunnelAcl ip access list allow a whole

outside_cryptomap_dyn_20 ip access list allow any 192.168.240.0 255.255.255.0

no pager

Outside 1500 MTU

Within 1500 MTU

192.168.1.150 outside IP address 255.255.255.0

IP address inside 192.168.0.35 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

IP pool local VPN_Pool 192.168.240.1 - 192.168.240.254

location of PDM 0.0.0.0 255.255.255.0 outside

location of PDM 192.168.1.26 255.255.255.255 outside

location of PDM 192.168.240.0 255.255.255.0 outside

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_outbound_nat0_acl

NAT (inside) 1 192.168.0.0 255.255.255.0 0 0

Access-group outside_access_in in interface outside

group-access INTERIOR-IN in the interface inside

Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

AAA-server GANYMEDE + 3 max-failed-attempts

AAA-server GANYMEDE + deadtime 10

RADIUS Protocol RADIUS AAA server

AAA-server RADIUS 3 max-failed-attempts

AAA-RADIUS deadtime 10 Server

AAA-server local LOCAL Protocol

Enable http server

http 192.168.0.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

Permitted connection ipsec sysopt

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

client authentication card crypto outside_map LOCAL

outside_map interface card crypto outside

ISAKMP allows outside

ISAKMP identity address

part of pre authentication ISAKMP policy 20

encryption of ISAKMP policy 20

ISAKMP policy 20 md5 hash

20 2 ISAKMP policy group

ISAKMP duration strategy of life 20 86400

Swanton vpngroup address pool VPN_Pool

vpngroup swanton 192.168.1.1 dns server

vpngroup swanton splitting swanton_splitTunnelAcl tunnel

vpngroup idle 1800 swanton-time

swanton vpngroup password *.

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd address 192.168.0.36 - 192.168.0.254 inside

dhcpd dns 8.8.8.8 8.8.4.4

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd outside auto_config

dhcpd allow inside

scott hwDnqhIenLiwIr9B of encrypted privilege 15 password username

username password encrypted ET3skotcnISwb3MV privilege 2 norm

username password tarmbrecht Zre8euXN6HxXaSdE encrypted privilege 2

username, password jlillevik 9JMTvNZm3dLhQM/W encrypted privilege 2

username privilege 15 encrypted password 49ikl05C8VE6k1jG ruralogic

username bzeiter 1XjpdpkwnSENzfQ0 encrypted password privilege 2

name of user mwalla encrypted password privilege 2 l5frk9obrNMGOiOD

username heavyfab1 6.yy0ys7BifWsa9k encrypted password privilege 2

username heavyfab3 6.yy0ys7BifWsa9k encrypted password privilege 2

username heavyfab2 6.yy0ys7BifWsa9k encrypted password privilege 2

username djet encrypted password privilege 2 wj13fSF4BPQzUzB8

username, password cmorgan y/NeUfNKehh/Vzj6 encrypted privilege 2

username password cmayfield Pe/felGx7VQ3I7ls encrypted privilege 2

username privilege 2 encrypted password zQEQceRITRrO4wJa jeffg

Terminal width 80

Cryptochecksum:9005f35a85fa5fe31dab579bbb1428c8

: end

[OK]

Any help will be greatly appreciated

BJ,

You try to access resources behind the inside interface network?

IP address inside 192.168.0.35 255.255.255.0

If so, please make the following changes:

1 SWANTON_VPN_SPLIT permit access ip 192.168.0.0 list 255.255.255.0 192.168.240.0 255.255.255.0

2-no vpngroup swanton splitting swanton_splitTunnelAcl tunnel

Swanton vpngroup split tunnel SWANTON_VPN_SPLIT

outside_cryptomap_dyn_20 3-no-list of ip access allowing any 192.168.240.0 255.255.255.0

4 - isakmp nat-traversal 30

Let me know how it goes.

Portu.

Please note all useful posts

VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK

I tried to set up a simple customer vpn using this document

http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801e71c0.shtml

VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...

6.3 (5) PIX version

interface ethernet0 car

Auto interface ethernet1

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

activate the encrypted password of VmHKIhnF4Gs5AWk3

VmHKIhnF4Gs5AWk3 encrypted passwd

hostname VOIPLABPIX

domain voicelab.com

fixup protocol dns-length maximum 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol they 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol 2000 skinny

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names of

access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

pager lines 24

Outside 1500 MTU

Within 1500 MTU

IP address outside 208.x.x.11 255.255.255.0

IP address inside 172.10.2.2 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

IP local pool voicelabpool 172.10.3.100 - 172.10.3.254

history of PDM activate

ARP timeout 14400

NAT (inside) - 0 102 access list

Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1

Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

AAA-server GANYMEDE + 3 max-failed-attempts

AAA-server GANYMEDE + deadtime 10

RADIUS Protocol RADIUS AAA server

AAA-server RADIUS 3 max-failed-attempts

AAA-RADIUS deadtime 10 Server

AAA-server local LOCAL Protocol

Enable http server

http 172.0.0.0 255.0.0.0 inside

http 0.0.0.0 0.0.0.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

Permitted connection ipsec sysopt

Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac

Crypto-map dynamic map2 10 set transform-set trmset1

map map1 10 ipsec-isakmp crypto dynamic map2

client authentication card crypto LOCAL map1

map1 outside crypto map interface

ISAKMP allows outside

ISAKMP identity address

part of pre authentication ISAKMP policy 10

ISAKMP policy 10 encryption aes-256

ISAKMP policy 10 sha hash

10 2 ISAKMP policy group

ISAKMP life duration strategy 10 86400

vpngroup address voicelabpool pool cuclab

vpngroup dns 204.x.x.10 Server cuclab

vpngroup cuclab by default-field voicelab.com

vpngroup split tunnel 101 cuclab

vpngroup idle 1800 cuclab-time

vpngroup password cuclab *.

Telnet timeout 5

SSH 208.x.x.11 255.255.255.255 outside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH 172.10.1.2 255.255.255.255 inside

SSH timeout 60

Console timeout 0

username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2

Terminal width 80

Cryptochecksum:b03a349e1ac9e6022432523bbb54504b

: end

Try to turn on NAT - T

PIX (config) #isakmp nat-traversal 20

http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1

HTH

Cisco ASA 5505 VPN L2TP cannot access the internal network

Hello

I'm trying to configure Cisco VPN L2TP to my office. After a successful login, I can't access the internal network.

Can you jhelp me to find the problem?

I have Cisco ASA:

within the network - 192.168.1.0

VPN - 192.168.168.0 network

I have the router to 192.168.1.2 and I cannot ping or access this router.

Here is my config:

ASA Version 8.4 (3)

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.1.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP 198.X.X.A 255.255.255.248

!

passive FTP mode

permit same-security-traffic intra-interface

the net-all purpose network

subnet 0.0.0.0 0.0.0.0

network vpn_local object

192.168.168.0 subnet 255.255.255.0

network inside_nw object

subnet 192.168.1.0 255.255.255.0

outside_access_in list extended access permit icmp any any echo response

outside_access_in list extended access deny ip any any newspaper

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

IP local pool sales_addresses 192.168.168.1 - 192.168.168.254

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

NAT dynamic interface of net-all source (indoor, outdoor)

NAT (inside, outside) source inside_nw destination inside_nw static static vpn_local vpn_local

NAT (exterior, Interior) source vpn_local destination vpn_local static static inside_nw inside_nw-route search

!

network vpn_local object

dynamic NAT interface (outdoors, outdoor)

network inside_nw object

NAT dynamic interface (indoor, outdoor)

Access-group outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 198.X.X.B 1

Timeout xlate 03:00

Pat-xlate timeout 0:00:30

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

AAA authentication enable LOCAL console

the ssh LOCAL console AAA authentication

AAA authentication http LOCAL console

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

IKEv1 crypto ipsec transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac

transport in transform-set my-transform-set-ikev1 ikev1 crypto ipsec mode

Crypto-map Dynamics dyno 10 set transform-set my-transformation-set-ikev1 ikev1

card crypto 20-isakmp ipsec vpn Dynamics dyno

vpn outside crypto map interface

Crypto isakmp nat-traversal 3600

Crypto ikev1 allow outside

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH 192.168.1.0 255.255.255.0 inside

SSH timeout 30

Console timeout 0

management-access inside

dhcpd address 192.168.1.5 - 192.168.1.132 inside

dhcpd dns 75.75.75.75 76.76.76.76 interface inside

dhcpd allow inside

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal sales_policy group policy

attributes of the strategy of group sales_policy

Server DNS 75.75.75.75 value 76.76.76.76

Protocol-tunnel-VPN l2tp ipsec

user name-

user name-

attributes global-tunnel-group DefaultRAGroup

address sales_addresses pool

Group Policy - by default-sales_policy

IPSec-attributes tunnel-group DefaultRAGroup

IKEv1 pre-shared-key *.

tunnel-group DefaultRAGroup ppp-attributes

ms-chap-v2 authentication

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

no remote anonymous reporting call

Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13

: end

Thanks for your help.

You must test with 'real' traffic on 192.168.1.2 and if you use ping, you must add icmp-inspection:

Policy-map global_policy

class inspection_default

inspect the icmp

--

Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

Cannot access the internal network with Cisco easy vpn client RV320

I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?

Thank you

Hello

1. is the firewall on the active Windows 7 computer? If so, please disable it

2. can you check that you get a correct IP address in the range of the POOL of IP configured?

3. When you perform the tracert command to access an internal server, it crosses the VPN¨?

4. is the tunnel of split giving you access to internal IP subnets defined?

5. on the RV320 you see the user connected and sending and receiving bytes?

Don t forget to rate and score as correct the helpful post!

David Castro,

Kind regards

Need help to access the internal network via VPN on ASA5505 8.4 (1)

Recently, I upgraded my ASA5055 from 8.02 to 8.4 and since I have updated to the new version I can access my home network is no longer through the VPN. I can connect to the VPN with no problems however I can no longer ping or you connect to my network of 10.0. Someone would be kind enough to look at my config and tell me what needs to be added to make it work? In my old config, I had a statement of NAT for VPN that is no longer here.

I also wanted to configure WebVPN to work as well, and this is something that I've never been able to understand. Is it also possible that I can be on my 20.0 network and connect to the VPN and access 10.0 as well? When it is connected to my network of 20.0 I'm not received credentials to connect to the VPN. I would be grateful if someone can help out me. The major part of this is the first part of this question.

My configuration:

ASA Version 8.4 (1)

!

ASA5505 hostname

domain xxxxxxxx.dyndns.org

enable encrypted password xxxxxxxxxxxx

xxxxxxxxxxxxxxx encrypted passwd

names of

nameserver 192.168.10.2

Office of name 192.168.10.3

name Canon 192.168.10.5

name 192.168.10.6 mvix

name 192.168.10.7 xbox

name 192.168.10.8 dvr

name 192.168.10.9 bluray

name 192.168.10.10 lcd

name 192.168.10.11 mp620

name 192.168.10.12 kayla

name 192.168.1.1 asa5505

name 192.168.1.2 ap1

name 192.168.10.4 mvix2

name 192.168.10.13 lcd2

name 192.168.10.14 dvr2

!

interface Vlan1

nameif management

security-level 100

IP address asa5505 255.255.255.248

management only

!

interface Vlan2

0050.8db6.8287 Mac address

nameif outside

security-level 0

IP address dhcp setroute

!

interface Vlan10

nameif private

security-level 100

IP 192.168.10.1 255.255.255.224

!

interface Vlan20

nameif Public

security-level 100

IP 192.168.20.1 255.255.255.224

!

interface Ethernet0/0

Description pointing to WAN

switchport access vlan 2

!

interface Ethernet0/1

Uplink port Linksys 12 description

switchport access vlan 10

!

interface Ethernet0/2

Description Server 192.168.10.2/27

switchport access vlan 10

!

interface Ethernet0/3

Uplink Eth1 management description

!

interface Ethernet0/4

switchport access vlan 30

!

interface Ethernet0/5

switchport access vlan 30

!

interface Ethernet0/6

switchport access vlan 30

!

interface Ethernet0/7

Description of Cisco 1200 Access Point

switchport trunk allowed vlan 1,10,20

switchport trunk vlan 1 native

switchport mode trunk

!

Banner motd users only, all others must disconnect now!

boot system Disk0: / asa841 - k8.bin

passive FTP mode

clock timezone PST - 8

clock summer-time recurring PDT

DNS server-group DefaultDNS

domain xxxxxxx.dyndns.org

network object obj - 192.168.50.0

192.168.50.0 subnet 255.255.255.0

Server network objects

host 192.168.10.2

network object obj - 192.168.10.0

192.168.10.0 subnet 255.255.255.224

network object obj - 192.168.20.0

subnet 192.168.20.0 255.255.255.224

network server-01 object

host 192.168.10.2

network server-02 object

host 192.168.10.2

xbox network object

Home 192.168.10.7

xbox-01 network object

Home 192.168.10.7

xbox-02 network object

Home 192.168.10.7

xbox-03 network object

Home 192.168.10.7

xbox-04 network object

Home 192.168.10.7

network server-03 object

host 192.168.10.2

network server-04 object

host 192.168.10.2

network server-05 object

host 192.168.10.2

Desktop Network object

host 192.168.10.3

kayla network object

Home 192.168.10.12

Home_VPN_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224

outside_access_in list extended access permit tcp any any eq 3389

outside_access_in list extended access permit tcp any any eq 2325

outside_access_in list extended access permit tcp any eq ftp server object

outside_access_in list extended access permit tcp any any eq 5851

outside_access_in list extended access udp allowed any any eq 5850

outside_access_in list extended access permit tcp any any eq pptp

outside_access_in list extended access udp allowed any any eq syslog

outside_access_in list extended access udp allowed any any eq 88

outside_access_in list extended access udp allowed any any eq 3074

outside_access_in list extended access permit tcp any any eq 3074

outside_access_in list extended access permit tcp any any eq field

outside_access_in list extended access udp allowed any any eq field

outside_access_in list extended access permitted tcp everything any https eq

outside_access_in list extended access permit tcp any eq ssh server object

outside_access_in list extended access permit tcp any any eq 2322

outside_access_in list extended access permit tcp any any eq 5900

outside_access_in list extended access permit icmp any any echo response

outside_access_in list extended access permit icmp any any source-quench

outside_access_in list extended access allow all unreachable icmp

outside_access_in list extended access permit icmp any one time exceed

outside_access_in list extended access udp allowed any any eq 5852

KaileY_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer of 36000

logging warnings put in buffered memory

recording of debug trap

asdm of logging of information

address record [email protected] / * /

exploitation forest-address recipient [email protected] / * / level of errors

Management Server host forest

MTU 1500 management

Outside 1500 MTU

MTU 1500 private

MTU 1500 Public

local pool IPPOOL 192.168.50.2 - 192.168.50.10 255.255.255.0 IP mask

local pool VPN_POOL 192.168.100.2 - 192.168.100.10 255.255.255.0 IP mask

no failover

ICMP unreachable rate-limit 1 burst-size 1

ICMP allow all outside

ASDM image disk0: / asdm - 641.bin

don't allow no asdm history

ARP timeout 14400

!

Server network objects

NAT (private, foreign) static tcp ftp 5851 service interface

network object obj - 192.168.10.0

NAT (private, foreign) dynamic interface

network object obj - 192.168.20.0

NAT (outside) dynamic public interface

network server-01 object

NAT (private, outside) interface static 2325 2325 tcp service

network server-02 object

NAT (private, outside) interface static udp syslog syslog service

xbox network object

NAT (private, outside) interface static service udp 88 88

xbox-01 network object

NAT (private, outside) interface static service udp 3074-3074

xbox-02 network object

NAT (private, outside) interface static service tcp 3074-3074

xbox-03 network object

NAT (private, outside) interface static tcp domain domain service

xbox-04 network object

field of the udp NAT (private, foreign) of the static interface function

network server-03 object

NAT (private, outside) interface static tcp https https service

network server-04 object

Static NAT (private, outside) interface service tcp ssh 2322

network server-05 object

NAT (private, outside) interface static 5900 5900 tcp service

Desktop Network object

NAT (private, outside) interface static service tcp 3389 3389

kayla network object

NAT (private, outside) interface static service udp 5852 5852

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

AAA authentication enable LOCAL console

AAA authentication http LOCAL console

the ssh LOCAL console AAA authentication

AAA authentication LOCAL telnet console

Enable http server

http 192.168.1.0 255.255.255.248 management

redirect http outside 80

location of SNMP server on the Office floor

SNMP Server contact [email protected] / * /

Community SNMP-server

Server enable SNMP traps snmp authentication linkup, linkdown cold start

No vpn sysopt connection permit

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto-map dynamic outside_dyn_map pfs set 20 Group1

Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1

life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds

Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

Crypto ikev1 allow outside

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH 192.168.1.0 255.255.255.248 management

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 30

Console timeout 30

access to administration management

dhcpd dns 24.205.1.14 66.215.64.14

dhcpd ping_timeout 750

dhcpd field xxxxxxxx.dyndns.org

dhcpd outside auto_config

!

dhcpd manage 192.168.1.4 - 192.168.1.5

dhcpd enable management

!

dhcpd address private 192.168.10.20 - 192.168.10.30

enable private dhcpd

!

dhcpd 192.168.20.2 public address - 192.168.20.30

dhcpd enable Public

!

a basic threat threat detection

statistical threat detection port

Statistical threat detection Protocol

Statistics-list of access threat detection

no statistical threat detection tcp-interception

Server NTP 192.43.244.18

Server NTP 129.6.15.28

WebVPN

internal Home_VPN group strategy

attributes of Group Policy Home_VPN

value of 8.8.8.8 DNS Server 4.2.2.2

Ikev1 VPN-tunnel-Protocol without ssl-client

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list Home_VPN_splitTunnelAcl

value by default-field www.xxxxxx.com

the address value IPPOOL pools

WebVPN

the value of the URL - list ClientlessBookmark

political group internal kikou

group attributes political kikou

value of 8.8.8.8 DNS Server 4.2.2.2

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list KaileY_splitTunnelAcl

XXXXXXX.dyndns.org value by default-field

username scottrog encrypted password privilege 0 xxxxxxxxxxxxxx

user_name john encrypted password privilege 0 xxxxxxxxxxxxxxx

username joek encrypted password privilege 0 xxxxxxxxxxxx

eostrike encrypted xxxxxxxxxxxx privilege 15 password username

username almostsi encrypted password privilege 0 xxxxxxxxxxxxxx

username ezdelarosa password xxxxxxxxxxxxxxencrypted privilege 0

type tunnel-group Home_VPN remote access

attributes global-tunnel-group Home_VPN

IPPOOL address pool

LOCAL authority-server-group

authorization-server-group (outside LOCAL)

Group Policy - by default-Home_VPN

authorization required

IPSec-attributes tunnel-group Home_VPN

IKEv1 pre-shared-key *.

type tunnel-group SSLClientProfile remote access

tunnel-group SSLClientProfile webvpn-attributes

enable SSLVPNClient group-alias

tunnel-group type ClientLESS remote access

tunnel-group kanazoé type remote access

attributes global-tunnel-group kanazoé

address VPN_POOL pool

by default-group-policy kikou

tunnel-group KaileY ipsec-attributes

IKEv1 pre-shared-key *.

by default-group Home_VPN tunnel-Group-map

!

!

context of prompt hostname

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:438ed6084bb3dc956574b1ce83f52b86

: end

ASA5505 #.

Here are the declarations of NAT for your first question:

network object obj - 192.168.100.0

255.255.255.0 subnet 192.168.100.0

NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.50.0 obj - 192.168.50.0

NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

And 'clear xlate' after the above and that should fix your first question.

I would check your second question and get back to you shortly.

Customer remote cannot access the server LAN via VPN

Hi friends,

I'm a new palyer in ASA.

My business is small. We need to the LAN via VPN remote client access server.

I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.

Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.

Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.

Who can help me?

Thank you very much.

The following configuration:

ASA Version 7.0(7)
!
hostname VPNhost
names
dns-guard
!
interface Ethernet0/0
nameif outside
security-level 10
ip address 221.122.96.51 255.255.255.240
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.42.199 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
!
ftp mode passive
dns domain-lookup inside
access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
access-list allow_PING extended permit icmp any any inactive
access-list Internet extended permit ip host 221.122.96.51 any inactive
access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.43.10-192.168.43.20

arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list VPN
nat (inside) 1 access-list PAT_acl
route outside 0.0.0.0 0.0.0.0 221.122.96.49 10

username testuser password 123
aaa authentication ssh console LOCAL
aaa local authentication attempts max-fail 3

no sysopt connection permit-ipsec
crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
isakmp enable outside
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption des
isakmp policy 1 hash md5
isakmp policy 1 group 2
isakmp policy 1 lifetime 86400
isakmp nat-traversal 3600
tunnel-group testgroup type ipsec-ra
tunnel-group testgroup general-attributes
address-pool testpool
tunnel-group testgroup ipsec-attributes
pre-shared-key *
telnet timeout 5

ssh timeout 10
console timeout 0

: end

Topology as follows:

Hello

Configure the split for the VPN tunneling.

Create the access list that defines the network behind the ASA.

ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0

Mode of configuration of group policy for the policy you want to change.

ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#

Specify the policy to split tunnel. In this case, the policy is tunnelspecified.
```
ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified 
```

Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.

ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List

Type this command:

ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes

Associate the group with the tunnel group policy

ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn

Leave the two configuration modes.

ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#

Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.

Kind regards
Abhishek Purohit
CCIE-S-35269

Cannot access the settings page for adobe flash player for installation

Hi guys, I have a Samsung android Tablet and I used to use adobe flashplayer until a recent update a few days ago. After the upgrade, I found that I can not see the pages on preview versions https://settings.adobe.com/flashplayer/mobile/f books on Google books. Briefly been searching the net I found that I need Flash for this function.
I manually downloaded flash player from the flash player Web page archives 11.1. Even if flash player is now installed, everytime I try to open it, I am directed to a page online - https:// settings.adobe.com/flashplayer/mobile. This page is still empty.
I would be grateful if someone could guide me on how to access the settings page
Kind regards
Roman.

Changed using Flash Player as it is irrelevant to the beta.

Adobe no longer manages the Flash Player for Android, and he received no security updates in ages. We strongly recommend that uninstall you it. In addition, there a lot of malicious software distributed as a player from sources who are not Adobe Flash. To minimize your risk of malware, only install applications directly from Adobe or through Google. The vast majority of Android malware infections from the summary use third-party app store.

If you absolutely need Flash Player for your mobile device, there are a few browsers that operate a Linux Flash Player based in a data center and broadcast content to your phone.

Puffin Web browser - the fastest mobile browser with Flash support on cloud on iPad, iPhone and Android.

Flash Player photon & browser - Android applications on Google game

Thank you!

BlackBerry software cannot access the blackberry to all Web site

I can't access to www.blackberry.com so I can't download blackberry link to let me transfer all data from ny ny etc Bold 9900 ot my Q10. Symantec (that I don't use and are not installed) puts a message that this is is a malicious Web site and evven when I clikc the possibility to access in any case it won't let me. I see no way to remove Symantec that I do not use Norton AntiVirus I use Mcafee. Help, please

Here is the download link: https://swdownloads.blackberry.com/Downloads/contactFormPreload.do?code=A8BAA56554F96369AB93E4F3BB06...

This is a direct download, if you can not download from here so you have a computer problem much more serious than what I see you now.

What is your operating system? What is your browser?

"Backup and Restore Center" I cannot access the drive c: for backup

I'm attmpting to make a backup using the "back up and Restore Center." On the screen, which asks "which disks do you want to include in the backup?" it shows my C: drive but does not allow me to select. C: drive is 254.1 GB and nothing 416,7 GB of free space on my external hard drive. Please let me know my options.

Hello

make backups on an external hard drive or DVD

see if this information helps you

How to make a backup of your data (all Vista versions)

http://www.vista4beginners.com/how-to-backup-your-data

How to restore your files

http://www.vista4beginners.com/how-to-restore-files

the 1st link below is how do the backup complete pc (Vista, full and professional company)

http://www.bleepingcomputer.com/tutorials/tutorial145.html

and that is how do to recover the backup complete pc

http://www.bleepingcomputer.com/tutorials/tutorial144.html

and here is the information of microsoft in restoring a system image backup

http://Windows.Microsoft.com/en-us/Windows-Vista/restore-your-computer-from-a-system-image-backup

If you have problems with the repost of process above in forum microsoft link that is specific to the backup below questions

"This forum supports questions for the default backup utility in Windows Vista, Server 2008 and beyond."

http://social.technet.Microsoft.com/forums/en-us/WindowsBackup/threads

Cannot access the Adobe servers for App updates? Why is this?

Hello
Paid Creative Cloud CC (before CS6) new members several weeks ago. Has been
able to download all the applications I need without problem.
But now, I can't get the APP UPDATES? Just got a message saying "Unable to Access Adobe Servers"
Using Mac OS X 10.10.2
Anyone had similar problems and how can it be resolved?
Thank you very much

updates CC:
http://prodesigntools.com/Adobe-CC-updates-direct-links-Windows.html
http://prodesigntools.com/Adobe-CC-updates-direct-links-Mac.html

CC updates of 2014:
http://prodesigntools.com/Adobe-CC-2014-updates-links-Windows.html
http://prodesigntools.com/Adobe-CC-2014-updates-links-Mac.html

CC updates to 2015:
http://prodesigntools.com/Adobe-CC-2015-updates-links-Windows.html
http://prodesigntools.com/Adobe-CC-2015-updates-links-Mac.html

FATAL ERROR: Cannot access the temporary directory for remote package "detached.pkl".

have already run antivirus

already uninstalled and re-installed the app, I wish to run (even used revounistaller and other programs to ensure that all this)

have already removed all the components of the registry associated with this application, I want to make it work with some programs

In my view, it is over 2 years old, but I just had the same ERROR FATAL happen on my departure upward and found that a power cable to one of my extra hard drives has been disconnected. I was redirecting my temporary files to a G: drive to save space on my SSD boot drive. After that I reconnected it to power, everything was good.

VDP: Cannot access the data store

Hello!
I have a problem.
Every day I see error for one of my servers in "reports":
2016-07 - 05T 06: 00:47.971 + error 06:00-[7F2F3FA5E700] [Originator@6876 = transport sub]
Cannot use hotadd mode to access the FileSrv1/FileSrv1_1.vmdk [Cisco2-datastore]: can't get using this method.
(Mounting VM using vm-3198 transport hotadd failed: cannot access the data store for one of the drives of the Machine virtual FileSrv1..)
At the same time, I havn't this error for the other servers.

"FileSrv1" has not has installed "VMWare tools". After the instalation "VMWare tools" on this server, the problem is resolved.

The VPN Clients cannot access any internal address

Without a doubt need help from an expert on this one...

Attempting to define a client access on an ASA 5520 VPN that was used only as a

Firewall so far. The ASA has been recently updated to Version 7.2 (4).

Problem: Once connected, VPN client cannot access anything whatsoever. Client VPN cannot

ping any address on internal networks, or even the inside interface of the ASA.

(I hope) Relevant details:

(1) the tunnel seems to be upward. Customers are the authenticated by the SAA and

are able to connect.

(2) by many other related posts, I ran a ' sh crypto ipsec her "to see the output: it

appears that the packets are décapsulés and decrypted, but NOT encapsulated or

encrypted (see the output of "sh crypto ipsec his ' home).

(3) by the other related posts, we've added commands associated with inversion of NAT (crypto

ISAKMP nat-traversal 20

crypto ISAKMP ipsec-over-port tcp 10000). These were in fact absent from our

Configuration.

(4) we tried encapsulation TCP and UDP encapsulation with experimental client

profiles: same result in both cases.

(5) if I (attempt) ping to an internal IP address of the connected customer, the

real-time log entries ASA show the installation and dismantling of the ICMP requests to the

the inner target customer.

(6) the capture of packets to the internal address (one that we try to do a ping of the)

VPN client) shows that the ICMP request has been received and answered. (See attachment

shooting).

(7) our goal is to create about 10 VPN client of different profiles, each with

different combinations of access to the internal VLAN or DMZ VLAN. We do not have

preferences for the type of encryption or method, as long as it is safe and it works: that

said, do not hesitate to recommend a different approach altogether.

We have tried everything we can think of, so any help or advice would be greatly

Sanitized the ASA configuration is also attached.

appreciated!

Thank you!

It should be the last step :)

on 6509

IP route 172.16.100.0 255.255.255.0 172.16.20.2

and ASA

no road inside 172.16.40.0 255.255.255.0 172.16.20.2

Help, please! Cannot access the web after connected to the VPN

Hello

I'm a newbie on Cisco products. I configured a Cisco ASA 5505 with VPN firewall. However, I can't access the web after I connected to the remote IPSec VPN. I also cannot connect to the bands using the intellectual property. But I can connect to the internal servers in the office with no problems.

Here is my setup, can someone help please? Thank you very much

ASA Version 8.2 (5)

!

host name asa

xxxxxxxxx.com domain name

enable the encrypted password xxxxxxxxxxx

xxxxxxxxxxx encrypted passwd

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.1.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address dhcp setroute

!

passive FTP mode

area of zone clock - 8 schedule

clock summer-time recurring PDT 1 Sun Apr 02:00 last Sun Oct 02:00

DNS lookup field inside

DNS server-group DefaultDNS

Server name 107.204.233.222

name-server 192.168.1.3

xxxxxxxxx.com domain name

inside_nat0_outbound list of allowed ip extended access all 192.168.1.96 255.255.255.240

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 192.168.1.0 255.255.255.0

NAT (inside) 1 0.0.0.0 0.0.0.0

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

the ssh LOCAL console AAA authentication

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH 192.168.1.0 255.255.255.0 inside

SSH timeout 5

Console timeout 0

interface ID client DHCP-client to the outside

dhcpd outside auto_config

!

dhcpd address 192.168.1.5 - 192.168.1.36 inside

dhcpd dns 107.204.233.222 inside the 192.168.1.3 interface

dhcpd allow inside

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal strategy group xxxxxxxx-sc

attributes of xxxxxxxx-sc group policy

value of 107.204.233.222 DNS server 192.168.1.3

Protocol-tunnel-VPN IPSec

XXXXXXXXXX.com value by default-field

xxxxx xxxxxxxxxxx encrypted password username

Strategy Group-VPN-xxxxxxxx-sc

remote access to tunnel-group xxxxxxxx-sc type

attributes global-tunnel-group xxxxxxxx-sc

address sc-pool pool

Group Policy - by default-xxxxxxxx-sc

tunnel-group xxxxxxxx-sc ipsec-attributes

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

call-home service

anonymous reporting remote call

call-home

contact-email-addr [email protected] / * /

Profile of CiscoTAC-1

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:5c1c99b09fb26fcc36a8bf7206af8e02

: end

Hello

Try adding the following commands

permit same-security-traffic intra-interface

NAT (outside) 1 192.168.1.96 255.255.255.240

Is there are always problems with VPN then I would maybe change VPN pool to anything other than something that comes into conflict with the LAN.

In this case, these configurations should do the trick

In order from top to bottom, they would do the following things
- First remove the pool VPN and VPN configurations
- Then remove the VPN pool
- Remake of the VPN Pool with different network
- Reattach the VPN pool for VPN configurations
- Configure NAT0 to the new cluster of VPN
- Remove the old line of the ACL of the configuration of NAT0
attributes global-tunnel-group xxxxxxxx-sc

no address-sc-swimming pool

no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

IP local pool sc-192.168.2.10 - 192.168.2.254 mask 255.255.255.0

attributes global-tunnel-group xxxxxxxx-sc

address sc-pool pool

inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0

no access list inside_nat0_outbound extended permits all ip 192.168.1.96 255.255.255.240

Of course you also have the NAT configuration for VPN pools new Internet traffic

NAT (outside) 1 192.168.2.0 255.255.255.0

Please rate if the information has been useful if this resolved the issue as mark responded.

-Jouni

Cannot access the internal resources for VPN site-to-site

Similar Questions

But now, I can't get the APP UPDATES? Just got a message saying "Unable to Access Adobe Servers"

Using Mac OS X 10.10.2

Anyone had similar problems and how can it be resolved?

Maybe you are looking for