Click on the button trigger programmatically after awhile

Similar Questions

• My computer does not work and comes up with message after I've click on the button for auto repair

  Hi my computer just stopped working when I turn it on it gives me the opition to repair or start normally once Ive clicked on the button for it to try to repair the computer which is recommended after a few hours, this message appears:

  Stop

  Unrecoverable system error

  Session manager failed to create patches pre protected

  System process stopped at unexpectably with a status of 0xc000003a

  System has been shut down

  Someone knows how can I get my computer working again please

  Thanks in advance

  Hi Charlenebaldwin,

  ·         Did you do changes on the computer before the show?

  ·         What version of the operating system is installed on the computer?

  ·         You are able to boot to the desktop or SafeMode?

  Follow these methods.

  Method 1: Disconnect all external devices except the keyboard and mouse.

  Method 2: Start your computer in last known good configurations.

  Using the last good known Configuration

  http://Windows.Microsoft.com/en-us/Windows7/using-last-known-good-configuration

  Method 3: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: If the problem does not persist, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 4: Run the Startup Repair tool and check if the problem persists.

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  Method 5: If the problem persists, perform a restore of the system recovery (winre) windows environment.

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

• Edit should only be done after clicking on the button

  Hello!!
  
  I use jdeveloper 11.1.1.5
  I had created an af:table and have also a button change.
  
  Unless my user clicks on the button change should not allow the user to enter the value in the table.,.
  
  For example; Before changing af:table disable = true after clicking on change disable = false af:table

  Why you don't just change EditingMode for your table to the clickToEdit

• Debug mode turns off after clicking on the button

  Hello
  
  I am using the Debug Mode in order to track down a problem, but when I click on an application button on a page in debug mode is disabled so I don't get the debug output that I'm after.
  
  In short, I do the following:
  
  (1) changing the page in the Application Builder
  (2) by clicking on the button "Run" to run the page
  (3) by clicking on the "Debug" button to activate the Debug Mode. The page is redisplayed with the release of debugging among the elements of the page then.
  (4) I then type some text in some fields in a form region and click on a button in the same region to create a record. The same page then reappears, but the Debug Mode is now disabled.
  
  Then I tried something similar using the schema of example COMMAND under the user name and a different workspace, and this time in debug mode is stayed on until what I turned off it explicitly.
  
  Is there something I need to do to keep active Debug Mode?
  
  Kind regards.
  
  John.

  John,

  The branch set on the page determines if the current value of & DEBUG. is used in the URL redirected to. In principle, which would not be resolved. You would have to edit the branch (and make a f? p URL with & DEBUG or debug position YES.)

  Scott

• Why can't I open a new tab after clicking on the button +?

  Usually I can click on the "open a new tab" button to open a new tab, but now, when I click on the button, nothing happens. I tried right clicking and choosing the option: 'New tab', but still no opening tab. However, new tabs open if I click on a link and it leads to a new window. I don't know why? How can I fix?

  Uninstall the toolbar Ask and it should work again. There is a compatibility issue with the Ask and Firefox toolbar that prevents the opening of new tabs.

• How stop the overlap after having clicked on the button to return to the previous label?

  Hello!

  I am a novice and doing an interactive book of five pages with Flash CS5.5 and ActionScript 3.0. I use buttons to navigate through the pages.

  I attributed to each page as label1, label2, label3, label4, label5. Each label contains several clips (whose sounds.)

  When I click on the button to access the next label, everything works fine. But when I click on the button to return to the previous labels, all sounds begin to play at onece and overlap between them.

  I did a simple FLASH file as an example to explain what I mean.

  SAMPLE SOUND OVERLAPPING. FLV

  That's the problem I have right now.

  SWF FILE:

  http://DL.dropbox.com/u/11630261/Flash/sound%20Overlapping%20sample.swf

  
  

  Please help me! I searched the internet and books that I have, but still cannot find a solution to this

  Thanks for your time! And please excuse my English.

  If you have (or should), at most a single sound at any time, you can use:

  SoundMixer.stopAll ();

  before you begin each sound.

• Newbie question: How do I hide a page after click on the button?

  Hello!

  My name is Rafael. I'm talking about the Brazil.

  I am new user on the AdobeCycle software

  I do a form and I need help, please.

  My project form has three pages:

  1st Page - Instrucion

  Page 2 - form with fields to fill in

  3ª Page - (this page will be hidden). This page will be information the information filled out by the user to the 2nd Page . Will be just text.

  What do I want?

  When the user click on the button send email, I want the page with the form is hidden and show the 3rd Page with information (no field, only the full text). I want to send the PDF file to the e-mail with the 1st Page and 3rd Page (just the text with the information).

  How can I do this? How do the 3rd Page (the information filled with page two)?

  No problem of Rafael,

  Adobe have a guide that is very useful to access many of the features of the fields here: http://partners.adobe.com/public/developer/en/tips/CalcScripts.pdf

  I think about her a lot.

  Then at page 164, it looks like access/change the color of the legend AND the value:

  TextField1.caption.font.fill.color.value = "R, G, B" / / change the color of the legend

  TextField1.font.fill.color.value = "R, G, B" / / change the color of the value

  If you want to change the color of the border, then this requires another script. The example on the blog we mentioned, examples on page 2 to change the color of the borders of the second row down): http://assurehsc.ie/blog/index.php/2010/06/laying-out-a-form/

  For example:

  VNAME var = this.name.toString ();

  xfa.resolveNode (VNAME + ".") ui.textEdit.border.edge") .stroke ="solid";

  for (var i = 0; i)<4; i++)="">

  this.ui.oneOfChild.border.getElement("edge",i).color.value = "255,153,0"; orange tint

  xfa.resolveNode(vName_+_".ui.textEdit.border").getElement ("edge", I) .thickness = "0,0200" in

  }

  In addition, here are some links that might interest you: Re: books or guides for Livecycle Designer

  Good luck

  Niall

• line should become updatble after clicking on the button update

  When the user interface is displayed line in the table is not the updateable (read only) when you click on the button update present at the top of the table at this time select a line button should become as editable. Can someone tell me how to do this. Thanks for your help.

  Hello

  in the table create text entries and now the ReadOnly property to bind a temporary variable of type Boolean.

  to do this use SPEL. ${oa.current.ViewAttribute}

  Now that the page loads all first set the transient true attribute. so that all lines are read-only.

  Now when you click on the update button, enter the event and the primary key of the row.

  To loop through the rows and if the primary key corresponds to that means that it is the line so on this set of rows of the
  attribute transient to be false so that become only that particular line can.

  There are many threads already for this purpose in the forum... look it up...

  Thank you
  Gerard

  Published by: Gauravv on October 28, 2009 04:29

• My XP will not be stopped until I clicked on the button "Stop the computer" twice?

  I'm installing and uninstalling programs again.

  I click on the button "turn off". Nothing happens.

  Click again, and he obeys.
  I have most of the software companies insist on my computer needs to run their programs: NET, MySql, Visual Studio, Adobe, WinPcap, ffdshow and so on; and a dozen toolbars, etc. in the registry that I deleted the last months; like most of the guys. Your feedback is very much appreciated.

  Hi jediYL,

  Follow these methods.

  Method 1: Performs a search using the Microsoft safety scanner.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Method 2: Scan the file system (CFS) auditor to repair corrupted files.

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  http://support.Microsoft.com/kb/310747

  Method 3: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  For reference:

  How to make a computer faster: 6 ways to speed up your PC

  http://www.Microsoft.com/atwork/maintenance/speed.aspx

• How can I get my mouse to grab things without having to click on the buttons, if I have the touch mouse on my laptop?

  How can I get my mouse to grab things without having to click on the buttons, if I have the touch mouse on my laptop?

  You will need to go to the control panel > hardware and sound > mouse and see if the settings for the mouse pad have a function called "Tap-to-click" or something similar in the description.  The exact name of this feature differs depending on the manufacturer of the software for the mouse.

  If you do not see this option to be available, you will have to probably go to the support site for the manufacturer of your PC and download the latest drivers for your model computer mouse pad and install.  Once installed, go back to the mouse settings in the Control Panel, where you will most likely available additional settings after the driver installed.  I hope that the "Tap-to-click" function will be available to turn on or off.

• Impossible to delete previously selected items from the drop-down lists at the click of the button Reset on a page of the screen.

  Hello

  I'm unable to clear previously selected items from the drop-down lists at the click of the button Reset on a page of the screen. The code I did to clear the previous value when the click on the button Reset is as below.

  {} public void onReinitialize (ActionEvent actionEvent)

  System.out.println ("onReinitialize is called ::");

  UIComponent uiComp = actionEvent.getComponent ();

  If (uiComp is nothing)

  {

  otherwise we use the button that we linked to that bean

  uiComp = getButtonResetByBean ();

  _logger.info ("reset fields: buttonID =" + uiComp.getId ());

  }

  on the other

  {

  _logger.info ("reset fields: CompID =" + uiComp.getId ());

  }

  Pass the component inside the uniforms, UIXForm, UIXSubform, UIXRegion, UIXPopup, RichCarousel

  or RichPanelCollection that contains the components to reset

  getTextIDLOV () .setValue (null);

  ResetUtils.reset (uiComp);

  }

  ---

  Using this code Iam able to clear the entrance to the text box but can not clear previously selected items from the drop-down lists when the reset button is clicked

  Can anyone please help on this issue.

  It's simple, you can set GenerateIsNullClauseForBindVars = "false" in the viewCriteria who created in EmployeeView

  After doing that it will fill the list of employees only after the Department selection

  Again check the enclosed application

  Ashish

• New inputext when you click on the button

  Hi all

  I have a table with three fields: ID (pk) and ParameterName, ParameterValue.

  In my web form: I do a button, when the user click on the button New Row-> new inputtext two show, they are ParameterName and ParameterValue.

  After user entered value for two inputtext-> click Save to insert it into the db table.

  Example of a web form like this:

  ParameterName: < administrator > ParameterValue: [email protected] >

  ParameterName: < member > ParameterValue: [email protected] >

  But on my web form must maintain the new value of line in there to inputtext.

  Thank you

  Take a look at af:forEach and af:iterator

  http://jdevadf.Oracle.com/ADF-richclient-demo/docs/tagdoc/af_forEach.html

  Oracle ADF - tips and Techniques: ADF UI - easy implementation of editable forms using the & lt; AF:iterator & gt;

• Disable the first/previous/next/last buttons when the user clicks on the button "create".

  Hello

  I have a requirement to disable the first/previous/next/last buttons when the user clicks on the button "create". The must be enabled after the user clicks on the submit, and then the button "validate".

  Is this possible please?

  Thank you.

  Hello

  Using BC4J in the model layer? If so, you might use an EL to the property of disabled button. Something like

  Replace in the binding attribute on your page (preferably the primary key of your form attribute).

  Arun-

  Edit: Check out this blog for more information on this EL: https://blogs.oracle.com/adf/entry/highlighting_new_rows_in_adf

• Problem of setting a value for the hidden item click on the button with processes action or pl/sql dynamic

  Apex 4.1

  Oracle 11g

  I have a page which consists of a main and several sub-regions area.  I have a pl/sql process in after the header SET_DISPLAY(:P400_DISPLAY:='MAIN';))

  Three subregions have a contional show where P400_DISPLAY = STORE.  It works in the hiding of the sub regions.

  Now, I want to change the value P400_DISPLAY to the STORE to show the subregions when I hit a button.

  I tried to create a dynamic action for the click on the Add button, but get the following error:

  The selected button uses a model of 'button' that does not contain the #BUTTON_ID substitution string #.

  I went to the models and found:

  Substitution strings

  Substitution strings are used in sub models to reference the value of the components. This report details use of string substitution for this model.

  Substitution string	Referenced	De	Description
  #LINK #.	Yes	Model	To be used in an attribute "href".
  #JAVASCRIPT #.	NO.		To be used in an "onclick" attribute
  #LABEL #.	Yes	Model	Button label
  #BUTTON_ATTRIBUTES #.	NO.		The attributes button
  #BUTTON_ID #.	NO.		ID generated button will be ID either the static button if defined, or if not will be a generated ID internally in the format 'B ' | [Internal ID of the button.

  I then tried to create a page process, pl/sql,: P400_DISPLAY: = 'STORE '; If the button is pressed.  The action of the button is submit page. However, it does not change the value of P400_DISPLAY and the subregions are hidden.

  Suggestions please on how to fix the template or change the value of P400_DISPLAY?

  The question of the root, it's that, even if you change the value of the element of your page, it is not visible to other areas of the page until it is in the session. Thus, any other action based on the value of the element of your page. the visibility of a control, a report based on the value of the item, etc. will be affected by changing the value of the item page until it has been changed in the session. Even after that, items are stored in the session, then you must do something to influence the revalued value. To see the effect of this, observe that your page will load and assesses the value of the element of your page, it sees which is the "MAIN" and mask areas. However, he didn't reassess after that.

  Then; your choices for this value set at the session are send the page, or use JavaScript to set the value in the session. If you use the latter, you will have to do extra work to make visibility tests be re - run, so, let's stick with the submit method.

  What you did above sounds correct to do this but, there are a lot of decisions, that you might have done that may have caused things to do not occur in the correct order.

  First of all, we will confirm that what I describe above is your problem. From the development environment, load the page, click on the button to change the value and submit. Now, click on the link marked the Session. He is always at HAND? If the answer is "Yes"; That's your problem.

  Let's start with your calculation after the header. You set it to * only * run if the current value of the element of your page is null? If this isn't the case, it's your problem.

  Load the Page-> Item set to 'Hand' by calculation-> click on the button--> Item set to STORE-> Submit-> Page Load-> point by calculating the value 'hand '.

  See the problem?

  Assuming that's not the question, you have created a branch to the same page, right? What is your process for the branch point? Is it * after * Validation, computation etc.? Because if not, you are not changing the value before that didn't get to submit.

  I bet that's the first question, but take a look at these.

  See you soon,.

  -Joe

• Is it possible to have several break the view have need to click on the button 'continue' to continue?

  Is it possible to have several breaks notice require to click on the button 'continue' to continue?

  Yes I know it s crazy frustrating. It took me three days to figure out what I had to do.

  You could get my file but I Don t know where to download.

  You set movie (click the play next to the movie icon and choose reading). No automatic reading of the symbol or triggers tell the movie to play (if you intend to work they way I wanted, which is impossible to tell). There are probably other ways, but none of the 2000 I tried before worked.

  When you´ve set the movie to play, mark the spot on the timeline of the movie where you want to pause, and then click pause in playback of movies. Define a trigger on the chronology of the symbol with playback > stop all > 'your symbol name' in the symbol timeline just to the right of the pause. Then set to play again to the right of the shutter release. Make a button with action play chronology of 0

  It sounds very complicated, but it s not. Find how it was REALLY hard for me anyway