Color Laserjet CP1518ni: Color RED is misaligned - won't calibrate.

Similar Questions

• Can I solve the problems of alignment is to have my Color LaserJet CP1518ni? Red will not line up.

  Can I solve the problems of alignment is to have my Color LaserJet CP1518ni?  Red do not line up, I installed the latest updates, etc.  Calibration does not help.  The printer is only a few years old.  What gives?

  Hi threre, I just work on HP CP1518ni a client with this same alignment problem as most of you are describing. I went through some process and I think I found one that works... If all goes well it will work for

  You too.

  Things I tried before hand... also this machine has all the toners brand HP 90 + life on each of them.

  -Calibrate - has not fixed the problem (tried once)

  -reset the NVRAM - did not problem

  -removed and inspected print cartrides (no problem found), re-installed - fixed no problem

  The 'fix '...

  First, go to the HP website and download the firmware, make sure you only select the right operating system

  you are using. (for me it was Windows XP) Also the requirements of course read, I think you have to

  have with XP SP2 if it perhaps questions, always read the instructions before doing the firmware.

  Here is a quick link to the CP1518ni...

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3422472 & LC = on & CC = US & DLC = in & lang = to & CC = US

  Then, assuming you have the appropriate printer driver installed, double-click the utility you just downloaded and select the CP1518ni from the drop-down list. Now, press the button 'send the firmware '. It will be

  Take a few minutes so just let it do its thing. After that she did try to print something, for me it was NOT fixed.

  Now you want to calibrate the device, maybe 2 or 3 times, on the control panel scroll to the right until

  you see "systemsetup" press ok and scroll to the right again until you see 'print quality' and press ok.

  the first item in this menu is press "calibrate color" ok, now he's going to say 'calibrate now' and press ok one

  last time. It will start the calibration process. Then he did print something new to see how he does.

  for me I had to do the calibration process twice before the quality was normal again.

  Good luck, hope this helps some, I read that some printers still presist even after this process.

• Color Laserjet Cp1518ni alignment no longer work

  I have 2 x Color Laserjet CP1518ni for about three years now. Both printers do not calibrate corretly.

  I have problems with the logos of color printing. I now see magneta shadows as a result of misalignment.

  -J' have Windows 7, where the HP difficulty tools do not work. So I use the buttons on the printer

  -But also trying to calibrate with my laptop with Windows XP on it.

  -Installed new firmware, used each menu item I hoped that might have an effect.

  -Searched and searched on the internet, I found that nothing works.

  -Does someone have an idea to solve this problem?

  Hello

  Follow the instructions below to restore the default settings, and then test the print quality. Let me know what you find?

  http://support.HP.com/us-en/document/c01530973

• Color LaserJet CP1518ni: HP Universal Print Driver for Windows PC (64-bit) will only print black on Color LaserJet CP1518ni

  HP Universal Print Driver for Windows PCL6 (64-bit) will only print black on Color LaserJet CP1518ni

  Also, would like to have the complete software program to download rather than just the universal driver.

  Hello @wyodude

  Try this

  Go to devices and printers and right click on printer properties then go to device settings and go almost all the way down to the type of device a color change and save the changes then go in the printer preferences and in the color tab, make sure that in its unaudited grayscale printing option

• My HP Color LaserJet CP1518ni cannot print .pdf files

  Dear,

  I have a printing problem with my HP Color LaserJet CP1518ni (function USB my iMAC), since I installed the OSX Mavericks.

  Although my printer print word files, cannot print .pdf, even through the software PREVIEW or ACROBAT files.

  It gives the break signal... any solution about that?

  It is very annoying.

  Thanks in advance for your comments or help!

  Hi Kpanag

  I understand that you cannot print the PDF files from the upgrade to Maverick.

  I'll be happy to help you with this.

  I check and repair the authorization to drive on the Mac.
  Go on the hard drive of the Mac, applications, utilities, disk utility, click Mac hardrive left side, click on verify disk permissions, when it is finished click on repair disk permissions.
  (when it's over will show disk repair completed)

  Run the Apple updates also. (the Mac uses probably drivers 10.8)

  Make sure Acrobat is up-to-date.

  If you need more simply make assistance let me know.

• need instructions for changing the ITB on hp color laserjet cp1518ni

  need instructions for changing the ITB on hp color laserjet cp1518ni

  Hello the circus,

  Unfortunately the ITB - transfer belt doesn't seem to be a replaceable piece by customer. You will need to call our technical support at the 800-474-6836, and they can help you get this problem is resolved. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://goo.GL/kQDB

  HP out of warranty of the Support Options for HP printers selection:
  http://goo.GL/WJ1Vb

• Satellite 1100-Z6: color RED of the display is missing

  Hello

  I have a 1100-Z6 portable Satellite which doen't show the color RED. For troobleshoot I went to the Intel graphics properties and under the upturned tab color each color gamma and noted the answer.

  The Green and blue to work very well, but nothing happens when I turn the Red up/down using the slider control so as a result, I have a blue/green tint on my screen.

  It is also the same on an external monitor so I suspect its something to do with the graphics card itself.

  Any ideas on how to solve this problem would be very welcome.

  Thanks in advance

  Hello

  have you tried to uninstall the graphics driver intel and download/install the latest version available? Would be useful to know because if you didn t have already tried it, it could be a software related issue.
  So, just go here: www.intel.com and download the drivers. Perform the reinstallation and say what is happening and if your problem has been resolved.

  Any comments would be appreciated.

  Welcome them

• Pro 9500 nozzle check print only the lower half of the motif on the colors red, green and cyan.

  Pro 9500 impressions of low nozzle printer test only half of the colors red, green and cyan.  The bottom half is normal (no scratches & etc.).  Upper half is completely empty.  Problem started with a single color and progressed to three.  Since the three colors are adjacent tanks, at the far right of the Assembly to the tank, is there possibly something something in common to all three?  What is a control problem?  Cleaning (both normal & deep) and the replacement of the tanks have had negative results.  Head alignment will not work.  "Can't do the printhead alignment."

  
  

• When I connect my laptop to my TV via the "vga" cable, the color red does not appear on the TV screen.

  Color problem

  When I connect my laptop to my TV via the "vga" cable, the color red does not appear on the TV screen.

  Problem with the video card, cable or tv.  I will try to update the video driver first.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Printing DCP color red problem - HP Officejet Pro 8500 Wireless All - in - One Printer, the 4th copy

  I have a HP HP Officejet Pro 8500 Wireless all-in-One Printer and try to print 75 copies of a program for our event. After the first 5-6 pages the RED in my program starts to turn magenta. I have new HP ink cartridges and print on HP Color Injet paper. I have renectly replaced the Black/Yellow Printhead (at least 6 months ago). At the beginning when I cleaned the printheads, I was able to print 2 or 3 pages showing my color RED. Then back to magenta. When I received the images of test after you have cleaned the print heads, they are all perfect, no lines.

  What happens and how can I solve this problem?

  Hi TM1997,

  Thanks for the reply!

  Given that the printer seems to work for a bit and then comes back to the same question, it must be a problem with the printhead (Cyan/Magenta one) or the ink lines that go from the cartridges to print heads. First of all, I would suggest that you check the warranty date on your printhead C/M. If it is under warranty contact HP Technical Support in your area and inquire about a replacement, but if not, it's you if you want to replace the print head, printer service, or look into an upgrade.

  Have a great weekend!

• Sir, I have windows 7, after the creation of PDF files the icon was in solid color red and grey, but now the icon changed to adobe acrobat 7 professional, logo, how can I get the icon or the old logo for my PDF files as the previous icon is very easy to i

  Mr President

  I have windows 7, after creation of the solid color red & gray icon PDF files, but now the icon has changed to adobe acrobat 7 Professional logo, how do I re obtain the icon or the old logo for my PDF files as the previous icon is very easy to identify, also I used acrobat adobe 7 Professional but this problem was not there.

  Hi manojp35249311,

  Acrobat 7 is not compatible with Windows 7, so it's difficult to judge how the application on an incompatible environment will behave.

  Please attach a screenshot so that we can diagnose the problem correctly.

  Kind regards

  Nicos

• strange color (red & green) spots appear after conversion of RAW files to JPEG, someone knows how to fix this?

  Strange color (red & green) spots appear after conversion of RAW files to JPEG, someone knows how to fix this? Thank you.

  Thank you all, I use rather than ProPhoto RGB sRGB and it's better now. Thanks again.

• LaserJet CP1518ni on software Mac OS 10.7 for this printer is currently unavailable

  "I'm trying to install the HP Color LaserJet CP1518ni on Mac OS X 10.7.5 and get this error: the software for this printer is currently unavailable.

  Hi Lorel509,

  Welcome to the HP Forums!

  I understand that you try to install your CP1518ni LaserJet on Mac OS 10.7, and I'm happy to help with this installation problem!

  Please see the installation guide. OS X Lion v10.7: install and use the printer with Lion, because I think it will help.

  Hope this information helps you and have a great day!

• Drivers HP LaserJet CP1518ni for WIN7-64

  I have the color Laserjet CP1518ni printer when I had Win Vista-32 and it works beautifully. Recently, I upgraded my OS WIN7-64 and installed the drivers recommended from HP website. I installed the HP Universal PCL6 v5.6.0, but the printer is not recognized as color and prints only in black and white.

  When I restore the old driver 32-bit, I had on vista, it works in color but does not print on the web I get an error message on a competibility of 32 bits.

  Help, please.

  After carefully reviewing the download section for the printer from the HP web site, I found that there is an update of the firmware on this printer and CP1510 version. So I updated the firmware and now it works fine, so far.

  I guess that was the problem.

• HP LaserJet CP1518ni - wireless installation, will now in offline mode after reboot

  I just install my printer wireless via my router and everything was fine - test pages, etc. I rebooted and after reboot, I can't use the printer.  It is "offline." Turn everything off and then does not solve the problem.  The printer is a Laserjet CP1518ni.  It is connected to my router and two computers use wireless. Don't know what to do. Help! Why is it keeps working after the first reboot?

  You can run printing HP and doctor Scan, and it can help with this problem.
  http://goo.GL/u3jDE

  It can also be a firewall or an antivirus which blocks. You can turn it off and try to print.