Communication between VBAI 3.6.1 and 1200 Siemens PLC

Similar Questions

• No communication between the Bluetooth SD - BT2 and PocketPC SD card

  I use an SD - BT2 (PA3271U) card in a Microsoft Pocket PC (also referred to as 'Microsoft PocketPC 2003') 4.20.00. I use the latest driver Toshiba 5.01 C and the card is recognized by the Pocket PC (Medion MD 95450 / MDPPC 150). I can connect to my mobile phone and GPRS connection is accumulation with no problems.

  But later at this point in time, the connection is established but dead... no connection to anyone. It seems that the communication between the Pocket PC and the card SD - BT2 is broken on the software side.

  Anyone have an idea (or a working driver) for this problem?

  Thanks in advance

  Karl

  Hello

  Have you tried to reinstall the drivers or software for SD - BT2?
  In my opinion, you should check this option.
  Also, I found a brand new version for PDA Bluetooth Stack (Bluetooth software and drivers).
  Check out this site.
  http://APS.toshiba-tro.de/Bluetooth/pages/download.php.

  Good bye

• Ethernet I / P Communication between Fanuc LR Mate 200iC and LabVIEW

  How can I read the outputs and write entries of a device, Ethernet/IP, using the NI Ethernet/IP drivers?

  I recently get the NI Ethernet/IP driver OR to communicate with a robot of 200iC Fanuc LR Mate using this communication protocol. In fact, I set up the robot as a parameter to map digital 1 to 64 and output digital from 1 to 64 and through the Ethernet/IP configuration.

  What I do is for example, a specific moment in my logic to the status of an output of the Fanuc Robot to take measures, or give some input to the Fanuc Robot so do some operations. Now, as I noted above, I get this drivers recently and apparently they are new or regular technical support do not support for this product. Basically there is no apartment of the LabVIEW help on this driver documentation, and this help doesn't help too much.

  So, if someone can help me to make this work I really appreciate it a lot. I'm in the middle of a project we showld integrate via Ethernet/IP. Here is a screenshot of the the inputs and outputs in the configuration of Fanuc Robot are on Slot 1. Attached is a table with a summary of the Fanuc Robot of the configuration settings that should be used to set up the scanner (in this case, LabVIEW):

  I'm using LabVIEW 2011 with Ethernet/IP v1.2 drivers on a Windows 7 Professional

  Once again, any help on this will be really appreciated. Thank you.

  Hi Ferdinand,.

  Please refer to the help as documentation below:

  1. open LabVIEW, go to the Help Menu-> NOR-Industrial Communications for Ethernet/IP. This is documentation of EIP support for all applications.

  2. in him getting started window of LabVIEW, please go to find examples. And check the directory:

  Input and output hardware-> NOR-Industrial Communications-> EtherNet/IP

  In this directory, there are several examples of use of the PPC.

  And for your case, read the example in ".vi AccessAssablyInstanceData (Explicit)", which should be very similar.

  For any question below, please do not hesitate to contact me.

  Thank you.

  Chris

• Difficult communication between Windows Server 2008 R2 and Windows Server 2008 R2

  I have a client-server application. The application server is installed (Jboss 4.2) on a computer that uses Windows 2003. The Jboss does not have Local system, but a user who has administrator rights. Among other features, this application communicates with other servers that use Windows Server 2008 R2, to find all the services of Jboss that are installed on these machines, their status, the databases that are connected to them, the ports (by checking the file jboss - service.xml, oracle - ds.xml). This communication is done by sending orders sc, as (and other controls to start and stop services):

  Status of request \\server SC = all | find/i 'jboss ' | find/i 'service_name ' | find/i "_q".

  My problem is that I have to migrate this application from Windows 2003 to Windows 2008 R2.  After I installed it on my new machine, I saw that the application is not behavies as it should. I managed to observe that the response time to send the same command (the one above) to Windows 2008 R2 to Windows 2008 R2 takes more time that sending the same command from Windows 2003 to Windows 2008 R2.

  Is something changed in the sc command or there's a problem with the security rights?

  If you have an idea, please give me a feedback.  This problem is beyond my knowledge.

  You can find server gurus in the following forums:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  This forum deals with domestic users of questions, so using Server forums you will get a much better response.

• communication between master blocking and blocking fowarding sensor sensor

  1. how the communication between the master sensor blocking and blocking fowarding sensor take place?

  RDEP or SSL or SSH? Which one?

  Forwarding of blocking sensors will use RDEP more 443 (https) to communicate with the master blocking sensor.

  To ensure that the sensor of blocking of the Master to allow connections from sensors transfer blocking under the hosts permitted configuration section.

  Here's a link for how to do this with VEI:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids10/idmiev/swchap3.htm#32776

  Hope this helps,

  Peter

• Communication between HP eprint and Google Cloud Print

  Hello

  communication between HP eprint and Google Cloud Print seems to be broken. At least for me.

  Documents to print when I print vio Chrome browser or Cloud Print dashboard - but the State in the clouds print remains "submitted". It seems that somehow the HP eprint status doen't get referred to cloud print. In HP eprintcenter paper says "printed".

  Well, I wonder who will take care of this problem...  (Hope this does not lead to fingerpointing only...)

  Thanks for your support!

  Best,

  George

  Started more work, a few weeks ago. All is well now. Don't know who that sets well.

• Communication between Labview and Rn42 Bluetooth

  Hello

  I am currently working on a project that requires communication between a bluetooth equipment and my pc with bluetooth built-in. The bluetooth hardware is verfied working with Blueterm on android. However I'm unable to connect with my laptop blueterm. Is back a unabe to connect error. I use bluetooth vi without series or visa. This method is suggested? Thank you

  
  

• No communication between the printer and the Red computer on switch flashing printer does on every time I turn it off

  I get a message there is no communication between the printer and the computer. Printer is all-in-one HP Officejet 4315v. Have uninstalled and reinstall the software and unplug the USB port and plug it back. Repeated several times. Still no communication. Exclamation red light next to 'on' and green button 'on' butter is flashing all the time.

  You have a hardware failure of the printer.  Contact the manufacturer for support.

• communication between the printer and the computer stops

  Original title: printer problem

  Without rhyme or reason communication between our computer and the printer just stops (often!)   Why?  and how to fix it?

  Hello

  ·                         try to uninstall and reinstall and use the latest printer drivers VISTA for your model of the manufacturer of the printer

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the information of the links to the other

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• Encrypted L3 Communications between the TOWER and WLC?

  Hi all

  I work with a client who wants to put the towers away to their WLC (a 4402). The problem is that communications between the TOWER and WLC must be secured, even through their private Wan! I have a few questions that result, if someone is able to help you;

  1. I can't know if and what method of encryption is (is it AES etc.?) used on connections between towers and the WLC and what are the steps?
     1. The terminology can be a problem here, it's not a wireless mesh, just classic LAP for WLC
  2. EXTENSIVE customer network is already encrypted (IPSec VPN via VPLS) in parts - what is the consequence of execution of AP<-->WLC with end to end (if possible) on a network encryption EXTENDED with IPSec, i.e. double encryption?

  Strange but true - pointers will be greatly appreciated... Phil.C

  With a controller of the 4400 series, the control traffic between the AP and the regulator is already encrypted AES.  The user traffic is not encrypted.  If you use a 5508 controller all traffic between the AP and the controller is encrypted AES.

  For what is running the traffic through a VPN, it should work.  The issue I see with this is with the MTU in general.  The controller will drop all packets with a payload of less than 32bytes data.  According to the MTU over the VPN I've seen packets getting fragmented and it is a question.  If you use one of the versions CAPWAP (5.2 or newer) discovery dynamic MTU is part of the Protocol and this MTU problem does not really exist.

• Can someone tell me what is the difference between a default playback device and a default communication device?

  original title: sound settings are very complex. Can someone tell me what is the difference between a default playback device and a default communication device?

  In fact, I use the recording software to record songs instead of downloading. Some recorders record their own drivers and they work fine. But sometimes, they do not respond. The DD Realtek Audio Manager is sick with something. People suffer a lot using this. My questions are endless. Some of them are:

  • What is "Realtek Digital Output?
  • Save devices-part of sound cards?
  • What are animals like 'Audio CD' and 'Stereo Mix' displayed on the DD Realtek Audio Manager?

  I'm sorry for not being specific, but I need a very good idea of how to deal with the settings of the sound in windows 7. And one thing, I have no microphone plugged but always Realtek HD Audio Manager detects? Why?

  Hi SandiKollol,

  A communication device can mean different things, but mostly it is used to allow voice communications on the internet.

  A playback device plays his return, such as your speakers or headphones.

  I hope this helps.

• No communication between the primary and standby

  Hello
  
  I have configured the DG,
  
  primary-> testprod
  standby mode-> testprod_s
  I started, standby machine instance watch with testprod and its place...
  but there is no communication between the primary and standby...
  
  How can I ask/check communication?

  Heartbeat PING [ARC3]: Unable to connect to the day before "testprod_s". Error is 12514

  eve of post form

  status of $lsnrctl
  $lsnrctl services

  When oracle not registered with listener service, this kind of errors occurred.
  The value of register LOCAL_LISTENER & manually as below in sleep mode and post

  SQL > alter the registry system;

• Disable communication between the host and the virtual machine

  I have VM Server 2.0 and one of the virtual machines has the same name as the server and even if the virtual computer is connected to the host only network it generates the Windows error message: duplicate names exist on the network.

  is there a way to disable communication between the host and the virtual machines? I just need a virtual network that is isolated from my network complete and host also.

  Thank you.

  The GUI Server2 is not to choose the other unused vmnets.  Then edit your file VMX use a different vmnet of 0, 1 or 8.  (which are bridged, host-only and NAT)

  Thus, for example, if your VMX has a line that says:

  Ethernet0.VNET = "VMNet0.

  change to:

  Ethernet0.VNET = "VMNet2.

  (This assumes that you have not used the network Editor to fill the vmnet2 either).

• Communication between TNS_Listener and the listener of the Apex

  Hi all
  I how communication between TNS Listener, receiver of the Apex and Apex? For some reason, I got the following error of Apex listener:

  Caused by: oracle.dbtools.rt.web.WebException: Unable to start the Universal Connection Pool: oracle.ucp.UniversalConnectionPoolException: Cannot get Connection from Datasource
  .
  .
  .
  Caused by: oracle.net.ns.NetException: Listener refused the connection with the following error:
  ORA-12505, TNS:listener does not currently know of SID given in connect descriptor

  I truncated messages Java object.
  
  This has happened when I tried to connect to the Apex. So I can fix it by going to:

  http://localhost:8080/apex/listenerConfigure

  then everything worked fine.
  
  My listener.ora file:

  LISTENER =
    (DESCRIPTION_LIST =
      (DESCRIPTION =
        (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
      )
      (DESCRIPTION =
        (ADDRESS = (PROTOCOL = TCP)(HOST = firefly.snowdrop.com)(PORT = 1521))
      )
    )
  
  ADR_BASE_LISTENER = /usr/local/oracle
  
  ADR_BASE_ORACLE_LISTENER = /usr/local/oracle

  My tnsnames.ora file

  INARA =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = firefly.snowdrop.com)(PORT = 1521))
      (CONNECT_DATA =
        (SERVER = DEDICATED)
        (SERVICE_NAME = inara.snowdrop.com)
     )
    )

  When inara is the name of the instance and the firefly is the host name.
  
  Is that the order of start if first the TNS Listener or listener Apex matter first?
  
  Best regards
  Val
  
  Published by: Valerie good-natured August 1, 2011 05:47

  Hi Val,

  My tnsnames.ora is configured for an existing server and there is no client configurations like sqlplus, sql or earpiece of the apex developer. However until now the server can connect to customers without problem (I just discover that unreproducible error on 'impossible to find the SID' sometimes occurs at the beginning of the Summit, the kick-off and can be solved by waiting for a while to connect to reconnect), so again I must modify the .ora?

  No, if your database listener is configured properly (i.e., he listens to the SID that you try to connect to the network interface/hostname/ip address /... she must use), there is no need to make any other configuration, especially not on another machine.

  -Udo

• Communication between Labview and Acton spectrometer via USB or RS232

  I'm trying to communicate between a PC running XP and a spectrometer to Acton 2300i using Labview.  Windows recongizes the specification and assigns it to COM3 with the correct name.  Also, the software provided with the specification can communicate with him.  However, I was unable to communicate using VISA in Labview.  I downloaded the simple read and write example vi fromt the example finder and changed the entries at 9600 baud... but I am still unable to connect.  I also tried connecting via software of measurement and automation NOR, but getting the timeout error code.  I was able to connect using GPIB of Labview for another more old Acton Spec 500i but the onle new version connects via RS232 or USB.

  The problem was simply not having a return of carrage added at the end of my order.  Thank you for your help.