communication between the printer and the computer stops

Similar Questions

• problems of communication between the computer and printer (wireless)

  I installed a wireless printer and its not connect with my laptop

  each model is different.  You will need to read the manual on this.  Most likely the IP address assigned to the printer is no longer valid in your current setup.

  from a command like use ping to see if the network route works

  Ping 1.1.1.1 (change the config page IP address 1.1.1.1).

  If you have configured the IP address as static you return to DHCP on the network.

  Alan Morris Windows printing team; Here Microsoft Knowledge Base search: http://support.microsoft.com/search/Default.aspx?adv=1

• No communication between the computer and the printer Photosmart D100 HD series

  Pentiun4 computer and HP Photosmart D110 seriesmy problem computer is HP but not accept the printer sends the signal to the printer. Thank you

  Hello

  1. what operating system is running on your computer?

  2. it worked earlier? If so, remember you have changed your computer?

  3. What is the exact error you receive?

  Follow the steps in this link and check if that helps: http://windows.microsoft.com/en-us/windows/help/printer-problems-in-windows

• No communication between the printer and the Red computer on switch flashing printer does on every time I turn it off

  I get a message there is no communication between the printer and the computer. Printer is all-in-one HP Officejet 4315v. Have uninstalled and reinstall the software and unplug the USB port and plug it back. Repeated several times. Still no communication. Exclamation red light next to 'on' and green button 'on' butter is flashing all the time.

  You have a hardware failure of the printer.  Contact the manufacturer for support.

• Lexmark Interpret S405 is not communicating with the computer and will not print

  My computer works with Windows 7 and updates automatically.  I got the Lexmark Interpret S405 for 18 months, and it has worked great until a couple of months.  When I try to print, I get an error message indicating that the printer is not communicating with the computer.  When I check the printer, it shows he's ready.  The print job shows that it is ready to print, but nothing happens except for this message.  When I try to erase the impression, it really takes a lot of time - usually have to unplug the printer so that it can finally clear.  Then it still will not print if I try again unless I restart the computer.  Lexmark support page says that there is a problem with Windows 7 and their product.  All the solutions for this problem yet?

  Computer model of the bridge ZX6970, OS 64-bit, intel CORE CPU I-13 3.30 GHz, Windows 7 Home Premium.  Can someone advise a fix for this problem?  Thank you!

  Hello

  Have you tried to download and install the updated firmware for the Lexmark Interpret S405 from the manufacturer's website.

  If this isn't the case, please download and install it.

  Download Firmware for your printer!

  We know the results.

• Printer is not communicating with the computer

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: I have problems with my Dell v305 printer I tried everything. Error message indicates that the printer is not communicating with the computer

  Hi vanessa James Sluys Veer,.

  Probably you should install/update your printer drivers for your operating system.

  Please see the link below for the Dell Web site:

  http://support.euro.Dell.com/support/topics/topic.aspx/EMEA/shared/support/DSN/en/document?c=UK&l=en&s=Gen&DN=1093016

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Disable communication between the host and the virtual machine

  I have VM Server 2.0 and one of the virtual machines has the same name as the server and even if the virtual computer is connected to the host only network it generates the Windows error message: duplicate names exist on the network.

  is there a way to disable communication between the host and the virtual machines? I just need a virtual network that is isolated from my network complete and host also.

  Thank you.

  The GUI Server2 is not to choose the other unused vmnets.  Then edit your file VMX use a different vmnet of 0, 1 or 8.  (which are bridged, host-only and NAT)

  Thus, for example, if your VMX has a line that says:

  Ethernet0.VNET = "VMNet0.

  change to:

  Ethernet0.VNET = "VMNet2.

  (This assumes that you have not used the network Editor to fill the vmnet2 either).

• No communication between the Bluetooth SD - BT2 and PocketPC SD card

  I use an SD - BT2 (PA3271U) card in a Microsoft Pocket PC (also referred to as 'Microsoft PocketPC 2003') 4.20.00. I use the latest driver Toshiba 5.01 C and the card is recognized by the Pocket PC (Medion MD 95450 / MDPPC 150). I can connect to my mobile phone and GPRS connection is accumulation with no problems.

  But later at this point in time, the connection is established but dead... no connection to anyone. It seems that the communication between the Pocket PC and the card SD - BT2 is broken on the software side.

  Anyone have an idea (or a working driver) for this problem?

  Thanks in advance

  Karl

  Hello

  Have you tried to reinstall the drivers or software for SD - BT2?
  In my opinion, you should check this option.
  Also, I found a brand new version for PDA Bluetooth Stack (Bluetooth software and drivers).
  Check out this site.
  http://APS.toshiba-tro.de/Bluetooth/pages/download.php.

  Good bye

• How to run code and to communicate between the computer and myRIO?

  Hello

  I am trying to create a colortracker using the myRIO. The system is pan tilt servo with a webcam. The project works well and is able to follow and move with the desired color. However, in order to continue the project, I want to ensure the system with another device for the perception of depth and want to use the host computer for webcam and image processing and the myrio to get signals for the servos. The idea is to connect two webcams directly to the computer usb ports and keep the myRIO connected to everything does time i.e. no wifi. Can anyone guide me as to how I would go about sending signals constantly between the computer host and myRIO?

  I advise to use Variables shared Network-Published or network stream.

  You can read about them both in the cRIO guide Developer: http://www.ni.com/pdf/products/us/fullcriodevguide.pdf

  There are also examples for both in the Finder for example LabVIEW.

• Hi, I have a toshiba tecra 5000 I downloaded updates when they try the third phase of the update download the computer stops and restarts.

  I'm a newbie with this stuff so bear with me.  I updated charges, when they get to the third stage of the download the computer stops and restarts. I tried all types of restart, the system is unable to connect. now the hard drive light on the face of the computer won't lite, the laptop won't even consider itself restart any ideas

  Hello

  1. the updates you downloaded?

  2 a successful installation of updates?

   

  Follow these methods and check

   

  Method 1:  If you are still not able to start the desktop computer, you can rename pending.xml and check.
  Renaming or removing the pending.xml file booting from the Windows Vista disc.
  a. Insert the installation disc.
  b. restart your computer.
  c.Press any key to load the disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings.
  d. choose your language settings, and then click Next.
  e. in the System Recovery Options menu, click command prompt
  f. at a command prompt, type the following command below and press ENTER
  CD C:\windows\winsxs

  g. now, type ren pending.xml pending.old , and then press ENTER.
  Restart the computer and check.
   
   
  Method 2:  Once you are able to boot to the desktop, follow this method.
  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7:
  http://support.Microsoft.com/kb/949358
   
   
   
  Thank you

• Does anyone know why when I run Defender and he finds a Trojan horse, and I try to remove it, it begins to make then after some time the computer stops

  original title: Defender

  Does anyone know why when I run the defender and he finds a Trojan horse, and I try to remove it it starts to do then after some time the computer stops and when I restart it Defender always tells me there is a Trojan horse and the same thing happens when I try to remove it?

  Hello

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Encrypted L3 Communications between the TOWER and WLC?

  Hi all

  I work with a client who wants to put the towers away to their WLC (a 4402). The problem is that communications between the TOWER and WLC must be secured, even through their private Wan! I have a few questions that result, if someone is able to help you;

  1. I can't know if and what method of encryption is (is it AES etc.?) used on connections between towers and the WLC and what are the steps?
     1. The terminology can be a problem here, it's not a wireless mesh, just classic LAP for WLC
  2. EXTENSIVE customer network is already encrypted (IPSec VPN via VPLS) in parts - what is the consequence of execution of AP<-->WLC with end to end (if possible) on a network encryption EXTENDED with IPSec, i.e. double encryption?

  Strange but true - pointers will be greatly appreciated... Phil.C

  With a controller of the 4400 series, the control traffic between the AP and the regulator is already encrypted AES.  The user traffic is not encrypted.  If you use a 5508 controller all traffic between the AP and the controller is encrypted AES.

  For what is running the traffic through a VPN, it should work.  The issue I see with this is with the MTU in general.  The controller will drop all packets with a payload of less than 32bytes data.  According to the MTU over the VPN I've seen packets getting fragmented and it is a question.  If you use one of the versions CAPWAP (5.2 or newer) discovery dynamic MTU is part of the Protocol and this MTU problem does not really exist.

• No communication between the primary and standby

  Hello
  
  I have configured the DG,
  
  primary-> testprod
  standby mode-> testprod_s
  I started, standby machine instance watch with testprod and its place...
  but there is no communication between the primary and standby...
  
  How can I ask/check communication?

  Heartbeat PING [ARC3]: Unable to connect to the day before "testprod_s". Error is 12514

  eve of post form

  status of $lsnrctl
  $lsnrctl services

  When oracle not registered with listener service, this kind of errors occurred.
  The value of register LOCAL_LISTENER & manually as below in sleep mode and post

  SQL > alter the registry system;

• Communication between HP eprint and Google Cloud Print

  Hello

  communication between HP eprint and Google Cloud Print seems to be broken. At least for me.

  Documents to print when I print vio Chrome browser or Cloud Print dashboard - but the State in the clouds print remains "submitted". It seems that somehow the HP eprint status doen't get referred to cloud print. In HP eprintcenter paper says "printed".

  Well, I wonder who will take care of this problem...  (Hope this does not lead to fingerpointing only...)

  Thanks for your support!

  Best,

  George

  Started more work, a few weeks ago. All is well now. Don't know who that sets well.

• How can I share network between the computer laptop windows 7 into a window of 8 tab?

  How can I share network between the computer laptop windows 7 into a window of 8 tab?

  Hi HollyMcColl,

  Thanks for posting your query in the Microsoft Community Forums.

  I understand from the description of the issue you are trying to share the computer network between Windows 7 and Windows 8. I will certainly help you in this regard.

  I appreciate if you could help me with more information.

  -Using Windows 8 Surface RT?

  Note: You can create a Windows RT PC home group, but you can join one.

  I suggest you to consult the help articles and check if it helps.

  A Wi - Fi & networking

  http://Windows.Microsoft.com/en-in/Windows-8/HomeGroup#1TC=T1

  Share files on a home network or your Surface

  http://www.Microsoft.com/surface/en-us/support/storage-files-and-folders/share-files-on-a-home-network?LC=1033

  Share files and folders on a network or shared PC

  http://Windows.Microsoft.com/en-us/Windows-8/share-files-folders

  Get back to us if you need further assistance on Windows 8. We will be happy to help you.

• Just installed Windows 7. Windows udate watch 21 important security updates but they will install. I get the error code 80070539. Tried to install the updates but the shut down the computer, but the computer stops until they install.

  Just installed Windows 7. Windows udate watch 21 important security updates but they will install. I get the error code 80070539. Tried to install updates by shutting down the computer, but the computer stops until they install.

  Hello Tallydupp, welcome.

  Do you by chance have Google Desktop? Some users have reported interference problems in Winodws 7 while using an older version of Google Desktop.
  Try to uninstall it if it exists.

  Let us know what happens

  Thank you! Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.