computer does not start until montor no video signal message

Similar Questions

• Computer does not start with the new video card

  Hello

  I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

  The video card is
  Sapphire ATI over-pants 2460

  I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

  It seems to me to have the latest version of the bios and windows 8

  What can I do else?

  Thank you very much

  Best,

  Korhan

  Hi JM,

  Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

  Your PC comes with one of the following built-in Intel graphics drivers:

  • Graphics Intel HD 4400 (GT2)

• VISTA computer does not start until "STOP: 0xc0000139 {Entry Point not found}".

  Original title: computer VISTA will not start

  I get this error when you try to start my vista 32 bit

  blue screen with:

  Stop c0000139 (entry point not found)
  Wcsncpy_s procedure entry point could not be located in the dynamic link library ntdll.dll.

  tried to start in every mood and nothing works. Help, please

  Hi Ad-HocHelp,

  (1) since when are you facing this problem?

  (2) remember to make changes to the computer before this problem?

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Step 2: Run the Startup Repair tool, follow the steps mentioned in the link below to access the system recovery tools.
  How to access the System Recovery Options menu?

  Run the tool to restart system as shown in the link below
  How to use Startup Repair?

  Thanks and greetings
  Ajay K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• computer does not start after power surge get to message x 300 128 MB BIOS

  I had a power surge of the House with the computer when I restarted I got a black screen with a 300 x is 128 MB bios p/n 113-a33406-100

  under that top left, a blinking cursor try don't reboot with pf8 no help

  Hello

  ·         What is the brand and model of the computer?

  ·         What is the last splash screen that is displayed, until you get the error message?

  ·         Were there recent changes made on the computer before the show?

  Please give us more information on this. Also, disconnect any external devices (printers, USB Hub, drives external, etc.) and try to start.

  Error-PC x 300 and 128 MB BIOS p/n 113-A33406-100 is linked to the Dell computer. If so, I suggest you to contact the Support Dell about this issue and check. You may experience this problem if the BIOS is damaged.

• computer does not start after installing video card

  I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

  Gary,

  You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

  When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

  Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• Computer does not start after running the utility Boot Lenovo.

  Hello
  I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
  Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
  When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
  Any idea what this problem could be? Would it be a bad power supply?
  Thank you

  Mario

  Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

  Thank you

• Error - NTLDR missing Windows XP Home computer does not start.

  Original title: XP-based computer does not start.

  XP Home does not start after I uninstalled a large file of Samsung mobile phone. I get a missing NTLDR error message and have had a System32 error as well, but there is no DOS prompt that would allow me to access anything whatsoever. Another problem is that I lost my installation CD. I initially bought this Dell PC nine over 6 years ago, so can provide identification details, if necessary program. Could someone tell me how I can make a recovery CD please? (No floppy drive not installed in the PC). To further complicate things (Yes, I know - I created many more problems that we all need), I have to keep my files on the hard disk, so cannot do a complete reformat, unless someone can tell how to save them somehow. My BACK skills could be summed up as "plodder inexperienced but determined!

  The file might be missing or it could just be that XP can't find it if your file system has somehow got corrupted.

  As the forums MS Answers does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  System32 error, you see, is what exactly?

  Depends on a few factors, there could be another copy of the file NTLDR in other places on your system, but you have to start on something to find out whether there is or not.

  After answering the above questions, I begin to make a CD from Recovery Console bootable XP by running a chkdsk/r, first on your HARD drive and then see what is left to do.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Help! My computer does not start

  My computer does not start. I get a message about missing files. What can I do?

  You may be able to perform a startup repair.

  Startup Repair is a Windows Vista recovery tool that can fix certain problems, such as system files missing or damaged, that might prevent Windows from starting correctly. When you run the Startup Repair, it scans your computer for the problem and then tries to fix it so that your computer can start correctly.

  Startup Repair is located in the System Recovery Options menu, which is located on the Windows Vista installation disc. If your computer manufacturer has preinstalled the recovery options, Startup Repair can also be installed on your hard drive. If your computer does not have the Startup Repair, your computer manufacturer can have customized or replaced the tool. See the documentation provided with your computer or go to the manufacturer's Web site.

  Please see the following site for more information on using Startup Repair:

  http://windowshelp.Microsoft.com/Windows/en-us/help/5c59f8c1-b0d1-4F1A-AF55-74f3922f3f351033.mspx#ex

  ·         Insert the installation disc.

  ·         Restart your computer.

  ·         Click Start, click the arrow next to the button lock and then click on restart.

  ·         If you are prompted, press any key to start Windows from the installation disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings.

  ·         Choose your language settings, and then click Next.

  ·         Click on repair your computer.

  ·         Select the operating system you want to repair, and then click Next.

  ·         In the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.

  If the Startup Repair tool is an option of recovering preinstalled on your computer:

  ·          Remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  ·         Click the Start button, click the arrow next to the button lock and then click on restart.

  ·          Do one of the following:

  o If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  o If your computer has multiple operating systems, use the arrow keys to select the operating system you want to repair, and then press and hold F8.

  ·          In the Advanced Boot Options screen, use the arrow keys to highlight repair your computer and press ENTER. (If repair your computer is not listed as an option, then your computer does not include startup as a preinstalled recovery option repair).

  Select a keyboard layout, and then click Next.

  ·          Select a user name and password, and then click OK.

  ·          In the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem and, if necessary, it may restart your computer, because it makes the repairs.

• My computer does not start a player - A does not exist and does not recognize my hard drive.

  My computer does not start. I tried to solve a problem with the disappearance of CD and DVD ROM drives, I unplugged then replugged cables connecting readers to the motherboard and when I rebooted, it told me to insert a bootable media in the floppy drive. I don't have a floppy drive. Before I tried to repair CDs and DVDs, my directory showed an A/floppy disk, because it seemed weird, yet benign, I don't think many, until my BIOS could not find my hard drive. It offers my USB drives and there is no such thing as a floppy drive to boot from. Help?

  If the drive is not detected in the bios, and I guess you actually mean the bios screen, then the drive has failed or the motherboard connections has a problem.

  Once in the bios screen try to reset for fail safe defaults, reboot, see if that makes a difference for the drive detected in bios

• I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  1. did you remove Bootcamp using disk utility?

  2 have you tried local restore or recovery of the Internet? - OS X: on OS X Recovery - Apple Support . Mac with built-in optical drives may need 'Gray' disks to boot the system.

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Pavilion dv7: my Pavilion Dv7 laptop computer does not start the system recovery options

  So it told me to turn my phone off, then back on whilist cling the key F11. But when I do it my is laptop beep loud noise and rest on the logo hp, whilist is on this screen is says 'System recovery F11' in the lower left corner and does not move on the screen, how to fix this?

  Hi @Jaytee2 ,

  Thank you for visiting the Forums HP's Support and welcome. I read on your HP laptop and get a blank screen or black at startup. Try perform a reset.

  When you perform a hard reset note remove all USB devices. Disconnect all non-essential devices.

  Here is a linkto computer does not start for Windows 7.
  
  Here is a documentthe performance of a Windows 7 system recovery.

  Do you have records system for this laptop?

  I'd be happy to help you if necessary. How can I find my model number or product number?

  Please let me know.
  
  Thank you.

• Computer does not start

  My computer does not start and it will not Mode without failure. I run the Memory Diagnostic test and it shows I have a hardware problem. I also tried to restore my computer to an earlier time, but it showed an error. I have 1 GB or RAM and recently she continues to change from 512 MB to 1 023 MB. Help, please.
  
  Care (I know)
  1 GB OF RAM
  INTEL CORE 2 DUO 2.43 GHz (I'm not sure)
  Card Gigabyte mother
  OPERATING SYSTEM: WINDOWS 7 ULTIMATE

  It seems that the memory must be replaced.  While you're at it, maybe get over 1 GB.  Windows 7 will run on it, but not well.  If the PC came with Windows Ultimate edition, it was more than likely 4 GB or more.

• Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

  I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

  In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

  HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

  Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

  Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).