computer laptop screen flickering and showing is not happy about half right side of the screen
In the past the entire screen will not display the content. flickers sometimes wildly, or shows just a whitish background.
problem has gotten worse lately.
If I touch the screen, the flashing stops sometimes, or the color goes from white to blue. other strange things:
sometimes if I keep on pressing against it, it shows a bunch of blue right in the Center, but I have the visible screen on both sides of it. any window, I opened can be seen partially on 1 half and the rest in the other half.
Unfortunately the band in the middle in this case takes realestate I can't see my internet connections etc. at the bottom right.
I have a Presario CQ6d, model CA60-615DX.
What should do?
Hi ShaneG1,
Thank you for the information. Here is the part number for the LCD 490097-1 d display Module 1.
Thank you.
Tags: Notebooks
Similar Questions
-
I have a new problem with my PC. My laptop suddenly crashed. It was working fine before this, but while I was watching a movie, it's just off. I tried to restart but it gave me the error that it cannot open because of software or a hardware error. It gives me two options: 1. to try the Startup Repair tool. 2. to open Windows normally.
I tried to open it normally, but it redirects me to startup repair. The Startup Repair is unable to do anything.
=================================================================================
Startup Repair can try to restore your computer to an earlier point in time when it worked correctly.
This repair will not personal data change, but it can remove some programs that have been installed recently. You can't undo this restoration.
=================================================================================
Then I tried to restore my PC to a previous restore point, but it won't let me continue once I've selected a point. It only shows my C drive which is grayed out so I can't select and continue. It gives me a yellow warning saying that the Protection of the system disk must be enabled.
So as the restoration is not an option, I went to the recovery of the system where it will restore my factory settings, deleting all data. The problem is that I have a lot of valuable data in the PC, so I don't want to do this before you have a back-up. I tried to make the back-up, but the first back-up was arrested at 78%. The second he stopped at 13%. After that all other attempts to create a backup stops at 25%.
I don't understand what to do. People say it's a problem with Windows 7 (64-bit). I don't have a Windows 7 CD either because it was pre-installed when I brought. I have an original CD of Windows Vista so I'll try to install first. Then, I'll try to copy my data and then restore my laptop to its factory settings. I hope this works.
A guy suggested to replace the names of readers. So I reversed the C drive and D drive. He showed me all the readers in the restore option. But the restore has failed. Then he renamed automatically drives to their original state. I even ran sfc/scannow, but it shows me that a scan is planned and restart the PC to start. But when I reboot, it gives me the same thing again.
Please suggest what to do...
I installed Windows Vista professional from the CD. It worked perfectly... I want to say that I was able to retrieve all my data because it stored in a folder called Windows.Old
But since I could not the wifi adapter and integrated graphics card Intel to work on the PC, I tried to restore factory settings. It doesn't let me access the Recovery Manager by pressing F11 on reboot I went to the computer icon and right-click on it. I selected manage and made my recovery disk a partition active. So after reboot it properly started the Recovery Manager. Right now I'm it back to factory settings. I'll let you know what happens after that. My data is safe, but I don't know if I'll be able to load my original OS.
-
computer laptop screen locked after trying to download free software for drawing fast vector engineer tools and now the break is unable to calculate or close the screen
Thank you
Bill
If your computer is bad, you need to do a system restore. Since it seems that you can not stop, try to hold the power button until it turns off. If this does not work, unplug (if laptop, remove the battery).
From there on, allows to do a restore:
- turn the computer on and start to tap F8 to get the start menu
- Select repair your computer
- Select System Restore
- Follow the prompts
If the restore point is older, feel free to use the Scan for affected programs feature to make sure that no other programs are affected. Otherwise, I would make a note of it, as it will have to reinstall these programs. In addition, I was running updated Windows once your system working again, since you will most likely use a restore point set up just before an update. (no point in re-opening of a security breach)
-
Hello, can someone help me to upgrade ram on HP Pavilion x 360-computer laptop 13-s102tu and also if anyone is familiar with how many slots there and what ram module supports this laptop?
Hello
Please use the part number and procedure on page 38 of the following guide:
http://h10032.www1.HP.com/CTG/manual/c04825536.PDF
(Note: same procedure for s1xx machines).
Kind regards.
-
My computer laptop sony vaio says operating system not found at boot
My computer laptop sony vaio says operating system not found at boot.
Hello
What is the model # computer? Check the following link to locate the model #:
http://eSupport.Sony.com/us/p/support-info.pl?info_id=264
Y at - it any hardware or software changes?
Remove all devices, dock and removable media connected to the computer and try the following steps to resolve the problem:
- Check if the hard drive is listed in the BIOS. Restart the computer > key 'F2 '.
- For Windows 8, shut DOWN the computer > press Assist key > key press F2 to access the BIOS.
- If the hard drive is not listed, the problem may be related with the material. Reset the BIOS once.
- Use the arrow keys on the keyboard to find the "Exit" button and select an option "Load optimized or default values", save the settings and exit the BIOS.
- Then check if you are able to start the operating system.
- In the case, if the problem persists, it may be related with the material.
- If the hard disk is listed, follow the procedure described on the link: https://us.en.kb.sony.com/app/answers/detail/a_id/30721/c/65, 66/kw/Error%20Operating%20system%20not%...
- In case, if the problem persists, contact the Sony service team: http://esupport.sony.com/US/p/service.pl
If my post answered your question, please mark it as an "accepted Solution".
-
Yes, all of a sudden, I got a security alert was attacking my computer or filtered in and I could not access Internet, I advocate for window / malware scanning and also, mcafee for extra security, but it happens still., why? Then a few days later, I was able to get on the internet again, only about 2 days, now I can no longer access the internet, Iget, open with file, message, so I guess I have to reinstall internet explore, some of my applications are not running, but I think that their always there. I have scan Windows / Defender and mcafee installed and running on my computer, so what's the problem here?
Hello
Download update and scan with the free version of malwarebytes anti-malware
http://www.Malwarebytes.org/MBAM.php
You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes
http://www.bleepingcomputer.com/download/anti-virus/rkill
If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking
Windows Vista
Using the F8 method:
- Restart your computer.
- When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
- Select the Safe Mode with networking with the arrow keys.
- Then press enter on your keyboard to start mode without failure of Vista.
- To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
- Do whatever tasks you need and when you are done, reboot to return to normal mode.
-
Computer laptop screen goes black when the VGA cable is connected, but you press TV poster display correctly when the VGA button on the remote control. I need the laptop screen too. It started just after years of correct use.
Original title: VGA:
In Panel > all items in the control panel > display > screen resolution you should be able to see the two devices / displays and be able to set options...
http://Windows.Microsoft.com/en-us/Windows7/change-your-screen-resolution
-
Monitor leaving them a 2-inch screen on the right side of the computer laptop hp Compaq cq40
Original title: full screen
After that I installed Windows 7 in my hp Compaq cq40 laptop monitor leave a 2-inch screen on the right side of the screen. I have set the screen resolution, reinstalled the latest driver. but still the screen is not displayed in full screen. If I install Windows Xp, then the display is in full screen mode. How can I get a display full screen with windows 7?
Hello
I suggest you to check if the steps help.
In Windows 7, click on the F11 key at the top of your keyboard. This will make Windows return a mode full-screen.
To cancel the mode full-screen and window restoration to normal display, press the Esc (Escape) key at the top of your keyboard.
Check your graphics card catalyst Center and change the settings from there.
I also suggest you go through the help article and check that it helps.
Use and adjustment of your monitor
-
My iPad and iPhone will be printed using AirPrint on my printer HP Deskjet 2540 for about 40 minutes and then will not be able to find all of the available air printers. No idea why. The deskjet printer shows that there is a wireless connection.
Hi Mpsfeldt,
Thank you for using communities Support from Apple!
Your question, it looks like you are only able to use AirPrint sporadically. We know that situations of this kind can be frustrating, but we are here to help.
To begin the process of solving problems, I suggest you to read about the section If you can not print on your printer AirPrint in the following article.
Best!
-
How do you reposisition the toolbar background down
Wednesday, June 13, 2012 19:45:28 + 0000, BJWoodham wrote:
My tool bar downstairs was on the right side of the screen when I turned on the PC this morning. How do come back on the bottom?
You say "toolbar." Do you mean the taskbar?
Although by default, the taskbar is displayed on the bottom of the screen,
It can be on any of the sides on what you prefer. To move any
side to side, simply click an unused portion and drag
where you want it. Don't forget to click inside it, not on the edge.
by clicking on the edge and dragging will resize not move.If it does not move, it can be locked. In this case, right click on it
and uncheck "Lock the taskbar", then try again.Moreover, with the screen monitors wide today, I prefer the taskbar
on the left or the right of the screen. I think that allows a better
use of real estate than have it at the bottom of screen.
Ken Blake, Microsoft MVP -
My phone displays a warning that a "peripheral USB attached to this computer has a malfunction and Windows does not recognize it." I uninstalled the only devices that I had (printer and bluetooth) but still this warning. Can anyone help.
Mike S.
I suggest to take a look at the following Web sites and follow their advice:
http://support.Microsoft.com/kb/871233
-
I have an old Photoshop CS3 that was installed on a desktop computer that has crashed and is still not bootable. I now have a new office with 10 windows and I installed it and it works. Activation is dimmed, but I can't save. It is said there is no internet connection, which is not correct. What should I do?
Please read https://forums.adobe.com/thread/1499014
-try some steps such as changing browsers and disable your firewall
-also clear the cache of your browser if you start with a fresh browser
-check the file hosts for blocked entries https://forums.adobe.com/thread/1912777
An idea that MAY work to install or run some programs in Windows 10 old... works for some, not for others
- or run as Administrator http://forums.adobe.com/thread/969395 to assign FULL permissions can help... said yet, but sometimes it is necessary for all Adobe programs (this is same as using an administrator account)
-
I have a problem I bought the collection master in 2012 for Mac just got a new computer with Windows 10 and I do not know how to download and install master collection on my new computer, can someone help me?
Available downloadable Setup files:
- Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
- Acrobat: DC, XI, X | Suite X | 9,8 | 9 standard | 8 standard
- Captivate: 8 | 7 | 6 | 5.5, 5 | 1
- Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
- Contribute: CS5 | CS4, CS3 | 3,2
- FrameMaker: 12, 11, 10, 9, 8, 7.2
- Lightroom: 6| 5.7.1| 5 | 4 | 3
- Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
- Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac
Download and installation help links Adobe
Help download and installation to Prodesigntools links can be found on the most linked pages. They are essential; especially steps 1, 2 and 3. If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".
-
When I print documents to the right side of the document gets cut it does not finish what was on the screen. This happens on all documents. I don't know what to do. I got a HP Photosmart Premium and he did it so I thought it was defective and bought a HP 7520e all in one and it does the same thing.
Hello
All changes made to the computer before the show?
Method 1:
See the link, run the Fixit and check.
Diagnose and automatically fix problems printing and printer
http://support.Microsoft.com/mats/printing_problems/en-us
Method 2:
If the methods above do not solve the problem you can check this link and follow the steps.
Printer in Windows problems
http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
Method 3:Try to adjust the alignment on the other side. Follow the steps.
- Click Start.
- Choose Control Panel.
- Choose a printer.
- Choose preferably to the printer.
-
Original title: computer screen
the impression of my screen is shifted to the right antinutritionnel the right side of the screen. Is there an easy way to fix this?
the impression of my screen is shifted to the right antinutritionnel the right side of the screen. Is there an easy way to fix this?
Do you remember a time when you did NOT have this problem?
If you do, do a system restore. Choose the date where you did not have this problem as your restore point.
http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/
Note...
1. it is a Feedback forum. It is not for computer problems.
2. always, always start by telling us what operating system you are using before describe you your problem.
3 this is the homepage of Ms. Answers.
http://answers.Microsoft.com/en-usSelect the first Version, and then select the forum to post your question.
Maybe you are looking for
-
Windows Vista and even Windows 07?
I am trying to download a game, but the system is Windows XP or Windows Vista. Well, I have Windows 07 is Windows Vista and Windows 07 looked at the same thing?
-
Have a power shot Sd1400 IS. It turns on then turns off and automatically displays the E16.
See the topic above.
-
Problems printing multiple 'current page' range of documents.
-Use of Word 2007 with a printer HP 1300 (Windows VISTA).-Select PRINT from the menu.-I am trying to print multiple copies of a page using "current page" to the print range.-I select the 'number of copies' and click OK, it will only print a copy.Whic
-
(Redirected) Lighting of R2 Alienware X 51 software?
I accidentally reset my computer and the software that came with the computer to change the color of the light is gone, any ideas on how to get it back?
-
Have download recipient return document
Hello World Adobe-So in short, here's what I'm trying to do:When I send you an I-9, Yes, you will need to sign (sign of Adobe for this) but the feature I'm trying to do, after having signed the form, you can download a document (PDF, Doc, etc.) and s