configuration adapter in PE2950 foreign

Similar Questions

• PERC 5 - no Configuration is present! Foreign import can damage the hard disk data ("this is an irreversible process)?

  Our 2950 has humming well when...

  Physical disk 0 change LED color from green to flashing orange.

  Configuring Raid 0 has 2 two identical disks combined into a VD.

  To troubleshoot an amber blink, we re sitting readers and even swapped their location, ultimately restore their substantive positions of basket in their original locations.

  Suddenly, amber LED changed to green new!

  However, the server is unbootable-"zero or logical drives found".

  Reports PERC 'no present Configuration!' in the config of VD but also two reports 2 error free readers in the config of PD.  He also pointed out a 1 DG and VD (1) and (2) PD in config stranger (contrary to what config VD reports - "no present Configuration."

  Ubuntu in rescue (booted from the CD) mode does not see two physical disks.

  What should we do?

  Thanks in advance - this server hosts the web services of a not-for-profit organization.

  Excuse the rawness, but you need to know about the functioning of the RAID and this server before trying anything. There are many places in which he could definitely bad (I'm not saying that isn't already).

  Start the utility CTRL-R, VD MGMT screen, highlight the controller, F2, foreign Import.

  If she fails to import, go to the CTRL MGMT screen and give me the version of the firmware of the lot.

  Next time, call Dell technical support or ask a question here to help them know what to do and how to solve it.

• RAID configuration PROBLEM

  Hello

  I have a little trouble on a server R610 in RAID5 with 3 disks and RAID H700 card.

  The 1st disk in "Foreign" State, the second in 'Fail' and the 3rd en 'Oneline '.

  The virtual disk 'offline '.

  Can I do a clear at the level of the 'foreign config' pour rebuild the 1st disk or DO I wait to replace the drive en "failure"?

  Thank you for your response.

  Laurent_Rio,

  The first chose you want to do is import the foreign configuration on the disk. (See below pour steps)

  This should use the reader to go online after its importation, then proceed to rebuild the defective disk.

  Do not erase the foreign, low - configuration you import it. In the BIOS of the controller RAID (Ctrl + R) highlight the controller of the group which includes the virtual disk, para on F2 and is the foreign configuration, then to IMPORT FOREIGN. After the failed drive can automatically start rebuilding, but if not then start the system and see if the data is accessible. If Yes, then you can get a backup, and then launch the reconstruction after.

  Let me know how it goes

  *******************************************************************************

  The first thing you want to do is to IMPORT the foreign configuration on the disk. (see below for the procedure)

  This will cause I hope the reader to go online after it is important and then proceed to rebuild on the failed drive.

  Do NOT clear the foreign configuration, remember to import.

  Controller raid BIOS (Ctrl-R) highlight the group controller that includes the virtual disk, hit F2 and select foreign Config, and then select IMPORT FOREIGN. After that the failed drive can automatically start to rebuild, but if not then start the system and see if the data is accessible. If Yes, then you can get a backup, and then start the reconstruction later.

  Let me know how it goes.

• RJVM has already been shutdown error when looking up foreign server

  Hello
  
  I'm trying to set up 2 new servers in a clustered environment. I configured a foreign server which is looking for queues on another server.
  
  The structure is as follows: 1 foreign with 2 queues and 1 Server makes connections with exactly the same name they present on the host server.
  When you start the server, I get an exception:
  
  < 5 November 2012 19:39:58 EET > < WARNING > < EJB > < BEA-010061 > < The Message - Driven EJB: ClonedQueueAnonymousWaiter is unable to connect to the JMS destination: MDB_QUEUE_RESPONSE. The error was:
  javax.naming.CommunicationException [root exception is java.rmi.UnmarshalException: RJVM has already been extinguished; nested exception is:]
  [java.io.IOException: RJVM has been arrested]
  at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:74)
  at weblogic.jndi.internal.WLContextImpl.translateException(WLContextImpl.java:470)
  at weblogic.jndi.internal.WLContextImpl.lookup(WLContextImpl.java:426)
  at weblogic.jndi.internal.WLContextImpl.lookup(WLContextImpl.java:411)
  at javax.naming.InitialContext.lookup(InitialContext.java:392)
  at weblogic.deployment.jms.ForeignOpaqueReference.getReferent(ForeignOpaqueReference.java:221)
  at weblogic.jndi.internal.WLNamingManager.getObjectInstance(WLNamingManager.java:96)
  at weblogic.jndi.internal.ServerNamingNode.resolveObject(ServerNamingNode.java:377)
  at weblogic.jndi.internal.BasicNamingNode.resolveObject(BasicNamingNode.java:856)
  at weblogic.jndi.internal.BasicNamingNode.lookup(BasicNamingNode.java:209)
  at weblogic.jndi.internal.WLEventContextImpl.lookup(WLEventContextImpl.java:254)
  at weblogic.jndi.internal.WLContextImpl.lookup(WLContextImpl.java:411)
  at javax.naming.InitialContext.lookup(InitialContext.java:392)
  to weblogic.jms.common.CDS$ 2.run(CDS.java:486)
  at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
  at weblogic.jms.common.CrossDomainSecurityManager.runAs(CrossDomainSecurityManager.java:131)
  at weblogic.jms.common.CDS.lookupDestination(CDS.java:480)
  at weblogic.jms.common.CDS.lookupDDAndCalloutListener(CDS.java:345)
  in weblogic.jms.common.CDS.access$ 100 (CDS.java:41)
  to weblogic.jms.common.CDS$ DDListenerRegistrationTimerListener.timerExpired (CDS.java:193)
  at weblogic.timers.internal.TimerImpl.run(TimerImpl.java:273)
  to weblogic.work.SelfTuningWorkManagerImpl$ WorkAdapterImpl.run (SelfTuningWorkManagerImpl.java:528)
  at weblogic.work.ExecuteThread.execute(ExecuteThread.java:207)
  at weblogic.work.ExecuteThread.run(ExecuteThread.java:176)
  Caused by: java.rmi.UnmarshalException: RJVM has already been arrested. nested exception is:
  java.io.IOException: RJVM has already been turned off
  at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:360)
  at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:259)
  at weblogic.jndi.internal.ServerNamingNode_1034_WLStub.lookup (unknown Source)
  at weblogic.jndi.internal.WLContextImpl.lookup(WLContextImpl.java:423)
  ... 21 more
  Caused by: java.io.IOException: RJVM has already been turned off
  at weblogic.rjvm.ResponseImpl.unmarshalReturn(ResponseImpl.java:234)
  at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:348)
  ... 24 more
  Caused by: java.io.IOException: RJVM has already been turned off
  at weblogic.rjvm.RJVMImpl.addPendingResponse(RJVMImpl.java:513)
  at weblogic.rjvm.RJVMImpl.send(RJVMImpl.java:900)
  at weblogic.rjvm.MsgAbbrevOutputStream.flushAndSend(MsgAbbrevOutputStream.java:394)
  at weblogic.rjvm.MsgAbbrevOutputStream.sendRecv(MsgAbbrevOutputStream.java:404)
  at weblogic.rjvm.BasicOutboundRequest.sendReceive(BasicOutboundRequest.java:109)
  at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:345)
  ... 24 more
  >
  
  WebLogic is installed in the Solaris machine and the version of welogic is 10.3.4.0 with Java version 1.6.0 update 33. I checked the firewall, / etc/hosts, but there is no problem with it.
  
  The JNDI connection URL is set up as: t3://xx.xxx.x.xx,xx.xxx.x.xx:7001/
  I tried to give it like this: t3://xx.xxx.x.xx:7001,xx.xxx.x.xx:7001/ or t3: / / hostname1, hostname2:7001 / or t3: / / hostname1:7001, hostname2:7001 /.
  but nothing has worked.
  
  Foreign servers are accessible from my Application Server when I telnet to the port. There is no required cross-domain security. Funny thing is that I have a same set up in two different application server (again) and he on the configuration of the same foreign server for IPs, I'm not facing problems at all.
  
  Can anyone help me please with this. Searched everywhere but have no idea about this topic. Many forums mentioned in connection to firewall and etc/hosts, but it's also not deal seems.
  
  Kind regards
  Africando

  The root cause of PeerGone is due with the exception of folklore here, as can be seen in the debug log.

  Caused by: weblogic.rjvm.PeerGoneException:; nested exception is:
  java.io.EOFException
  at weblogic.rjvm.ResponseImpl.unmarshalReturn(ResponseImpl.java:234)
  at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:348)

  You can debug it socket & messaging & perspective by adding additional logging to the list of else to debug it, that are already in place to check if this isn't a problem with the DNS name resolution or other issues

  -Dweblogic.debug.DebugMessaging = true
  -Dweblogic.debug.DebugMuxer = true
  -Dweblogic.debug.DebugMuxerDetail = true
  -Dweblogic.debug.DebugMuxerTimeout = true
  -Dweblogic.debug.DebugMuxerConnection = true
  -Dweblogic.debug.DebugMuxerException = true

• AQadapter - OSB11g

  Hi all
  
  I have a question about the AQ in OSB adapter.
  
  My system configuration:
  Oracle Weblogic 10.3.6
  11.1.1.6.0 Oracle service bus
  Oracle XE database
  
  My needs: I need to query data queue on the database and put them on a different queue in the database using OSB.
  
  what I did:
  I configured two queues in the database using sql scripts.
  With the help of developer J I created dequeue adapter to query the message and enqueue adapter to place the message in the queue.
  I imported the JCA and WSDL in OSB project and I created a proxy service and business. I have deployed and tested. Its working fine.
  
  But the problem here is that my project requirement which allows to choose the message using the adapter in Jdeveloper OSB.
  In the tension here is using some proxy protocols that call the queue on the database using JNDI connection.in the same for the service business also.
  
  Do we have a similar option to the use of protocols in OSB to choose the message in the queue in the database directly using JNDI to AQ adapter connection?
  
  Can anyone suggest me on this please?
  
  Kind regards
  Krishna.

  You can configure QA as a foreign JMS server and read messages from it.
  See this blog for an example:

  http://Tim.blackamber.org.UK/?p=1012

• E4X57PA #ACJ: graphics software

  Readon AMD graphics driver does not find to my Windows laptop, 10

  Download driver driver amd on the list but is not working properly. and don't see the graphical configuration adapted... pls help

• The TS engine insists that my VI prorotype changed after deployment

  But I don't see how, or when, and where.

  I hope I'm just something wrong. My situation is:

  System dev has Dev Suite, using TS 4.2 and LV 8.6.1

  Target system has 4.2 TS, LV 8.6.1 TIME std Base deployment engine

  @ Dev system (TS Seq Ed)

  • TS workspace
  • Outside the program is screw, the workspace includes 3 screws loaded dynamically and the executable file generated from the interface chart single of TS in LV
  • Configure-> adapter-> LV Dev system 8.6.1
  • Tool-> update VI calls
  • (Note that no prototypes have been updated)
  • Tools-> TS unfold
  • Load the deployment configuration file
  • The different ha from the default deployment configuration:

  "Deploy the TS file files" checked

  In "Options of LV' of files distributed:
  'Check for screws broken when parsing' checked

  "Check for broken screw after the Build" checked

  "Remove Unused Components VI" checked

  A program element for the executable of the user interface

  'Create an Installer' checked with the specified directories

  No drivers or selected engines

  • BUILD
  • Tell it to erase the old build directory
  • Generation seems OK - 1 caution regarding the name not renamed/moved (Blasted HP8341 driver)

  Copy the directory Vol 1 tree that results in my flash drive.

  @ The target system (even once, at TS 4.2 base deployment, LV 8.6.1 std RTE)

  • Plug a flash drive
  • Navigate to the installation directory
  • Run "setup.exe".
  • Click on Installer
  • See install go
  • Launch the executable file of the user interface
  • Press 'OK' to the admin, no passwd login
  • Point it @ my SuperDuperSpiffyCoolTS.seq file
  • "Single Pass".
  • BOOM

  "Error loading step"xxxxx"in sequence 'MainSequence' in the file 'SuperDuperSpiffyCoolTS.seq'.

  The prototype of the VI '' has changed.

  The prototype must be updated before you run the VI.

  To update the protytpe, open the dialog box specify Module

  Could not load the related module of a mandatory step. [Error code:-17600]

  • The stage on which it fails is the first step of the 'action' with a LV module in the sequence.

  I can fix by running the sequence 'programmatic_reload.seq' TS OR on the SuperDuperSpiffyCoolTS.seq installed on the target machince and everything works as expected after that.

  So where are my prototypes VI being changed? As part of the deployment step?

  Thanks for any idea/thoughts/help

  Tom McManus

  Hi Tom,

  In my opinion, that you see this behavior because you have the option to "Delete unused components VI" checked in the dialog box Options of LabVIEW VI. If you uncheck this option, your deployment will build properly and you will not see this error on your target computer.

  I tested your attached files with the 'delete unused components VI' option checked and reproduced the error but was unable to reproduce the error with the option unchecked.

  Please test this workaround solution to see if it behaves correctly your side also. Thanks for that bring to our attention! We will work to fix this in a future version of TestStand.

• PERC H310 H710p migration

  Hello

  I'm not an expert in RAID configurations but I am in charge of server Dell T320 my company and we will replace the storage controller that comes with it (H310) with a PERC H710p. We have a configured RAID-1 and we will continue to use the two disks of same after migration. We will replace the controllers.

  I know I have to do a backup before you replace the Exchange, but we will lose the RAID-1 configuration and data (including the operating system) after migration? Or it will be transparent to the system after reboot?

  Where can I find a type of paper that could guide me through this process because I don't want to wreck anything.

  Thanks a lot for your help.

  Jorge

  Hello.

  It is advisable to back up your data before performing any maintenance task. Ensure that you have a backup is valid data. The PERC H710 P supports the migration of virtual disk controller PERC H310. As a best practice, make sure that the hard drives and firmware H710 P is up to date. Replace the H310 and update the H710 P firmware with the controller cables disconnected from the background. Stop the server and connect the cables of the controller in the background and then restart.

  Your RAID configuration can be transparent to the system or appear in a foreign configuration. Clear the foreign configuration through the utility OpenManage Server Administrator (OMSA) or Ctrl + R for the POST.

  I would like to know how it works for you.

• Oracle forms/reports 12 c | Items on the Start Menu

  Hi guys

  I installed and configured Oracle weblogic 12 c (12.2.1), forms, and reports 12 c (Professional 64-bit Windows 10, 16 GB RAM, i7 processor platform) and be able to start the server administration Weblogic, wls_forms (wls_reports not yet configured). The only element of start menu, I could see as shown below with the image

  

  I'm not sure what exactly I missed during installation and configuration (Oracle® Fusion Middleware, installation Oracle Forms and Reports, 12 c (12.2.1), E66264-01) for the installation and configuration. Please help me

  Kind regards

  Did you follow that?

  Steps in order:

  • Ensure that the machine has the static IP address (or the loopback installed and configured adapter for Windows)
  • 8 RAM minimum concert
  • Open a shell (DOS) and set the PATH to include the JDK (8U51 + 64 - bit) first in the list
  • In the shell, run the WLS installation program and follow the instructions: java-jar fmw_12.2.1.0.0_infrastructure.jar
  • Run forms and reports 12.2.1 installer
  • Run the RCU THAT found in C:\Oracle\Middleware12\Oracle_Home\oracle_common\bin
  • Run the configuration (config) (if on Windows, do not forget the shell has administrator privileges) (C:\Oracle\Middleware\Oracle_Home\oracle_common\common\bin)
  • With a shell with administrator privileges, start Node Manager (startNodeManager) and then start Admin Server (startWebLogic) (C:\Oracle\Middleware\Oracle_Home\user_projects\domains\base_domain\bin)

  Once the servers have been launched successfully, the configuration will complete automatically.  This process also ends configurations required by design tools, the server startup if necessary to complete the steps.  They can be stopped if you are simply interested in examining the Builder (s), but obviously will not be able to run anything, if the servers do not work.

  I hope that between this overview and documentation, almost everyone should be able to get a good start.

  Hamid

• 12 c installation - UCR formulas

  Hello world

  I started playing with virtualbox (Win7 Ultimate) of shapes 12 c 2 facilities. (a standard and a full battery).

  Just a dumb question . where the RCU for 12 c?

  Thank you

  Jean-Yves

  Steps in order:

  • Ensure that the machine has the static IP address (or the loopback installed and configured adapter for Windows)
  • 8 RAM minimum concert
  • Open a shell (DOS) and set the PATH to include the JDK (8U51 + 64 - bit) first in the list
  • In the shell, run the WLS installation program and follow the instructions: java-jar fmw_12.2.1.0.0_infrastructure.jar
  • Run forms and reports 12.2.1 installer
  • Run the RCU THAT found in C:\Oracle\Middleware12\Oracle_Home\oracle_common\bin
  • Run the configuration (config) (if on Windows, do not forget the shell has administrator privileges) (C:\Oracle\Middleware\Oracle_Home\oracle_common\common\bin)
  • With a shell with administrator privileges, start Node Manager (startNodeManager) and then start Admin Server (startWebLogic) (C:\Oracle\Middleware\Oracle_Home\user_projects\domains\base_domain\bin)

• «JCA Binding run 'Write' reference operations have to: translation error.»

  Hi, I'm reading a file delimited with an incoming file adapter, I used a mediator to the records of the road to the outgoing file adapter. My input.txt file contains 10 recordings such as Fname, Lname.I have used the native format generator to generate xsd. To achieve the transformation, the Mediator, I have traced only the source to traget Fname using a foreach loop. I am trying to publish documents in batches of 2 then I configured adapter of incoming file accordingly. My incoming file adapter reads the first two records and the same is visible to the em console mediator instance (payload), I'm even able to see the first two records is there transformed the load transformed in the details for instance of mediator but the outgoing file adapter, I get an error saying:

  Error calling operation 1 channel 'write' on the service target "writeFile".

  Exception occurred when the link was invoked. Exception occurred during invocation of the JCA binding: "JCA binding run 'Write' reference operations have to: translation error.» Translation error. Error message in native format translation. Please ensure that the payload for the outbound interaction conforms to the schema. ". The called JCA adapter threw an exception of resource. Please review the error message above carefully to determine a resolution.

  
  

  When I map the Fname and Lname in the mapping of xsl file, I get the result. But I need only one field to the i: e the Fname and Lname the outfile.
  

  Below are the details of the interface:

  My Flow Interface: InboundFileAdapter - ReadsFile-> Medaitor - Transformation-> OutboundFileAdapter - writesFile

  
  

  Entrance of payload (comma-delimited text file)

  Brad, Pitt

  Keanu Reaves

  Martin, Lannoy

  Johnny, Depp

  .

  .

  etc.

  etc.

  Payload schema definition:

  <? XML version = "1.0" encoding = "UTF-8"? >

  " < xsd: Schema container = ' http://www.w3.org/2001/XMLSchema "

  ' xmlns:nxsd = ' http://xmlns.Oracle.com/pcbpel/nxsd "" "

  ' xmlns:tns = ' http://targetNamespace.com/ReadFile "

  " targetNamespace = ' http://targetNamespace.com/ReadFile "

  elementFormDefault = "qualified".

  attributeFormDefault = "unqualified".

  nxsd:version = "NXSD".

  nxsd:stream = "chars".

  nxsd: encoding = "US-ASCII" >

  < xsd: element name = "Root Element" >

  < xsd: complexType >

  < xsd: SEQUENCE >

  < xsd: element name = "Employee" minOccurs = "1" maxOccurs = "unbounded" >

  < xsd: complexType >

  < xsd: SEQUENCE >

  < xsd: element name = "Pnom" type = "xsd: String" nxsd:style = 'completed' nxsd:terminatedBy = ',' nxsd:quotedBy = "' & quot;" / > "

  < xsd: element name = "Lname" type = "xsd: String" nxsd:style = 'completed' nxsd:terminatedBy = nxsd:quotedBy ' ${eol} "=" "& quot;" / > "

  < / xsd: SEQUENCE >

  < / xsd: complexType >

  < / xsd: element >

  < / xsd: SEQUENCE >

  < / xsd: complexType >

  < / xsd: element >

  < / xsd: Schema >

  XSL map:

  < xsl: template match = "/" >

  < imp1:Root - item >

  < xsl: for-each select = "/ imp1:Root - element / imp1:Employee" >

  < imp1:Employee >

  < imp1:Lname >

  < xsl: value-of select = "imp1:Lname" / >

  < / imp1:Lname >

  < / imp1:Employee >

  < / xsl: foreach >

  < / imp1:Root - item >

  < / xsl: template >

  < / xsl: stylesheet >

  Please help me with the error mentioned above and if above transformation is possible using a mediator instead of BPEL

  Kind regards

  SAIF

  Hi Axel, thanks for your response.

  I got the result following your suggestion, but I could not understand the logic behind why we need to map all segments of the xsl file when we use same xsd to the incoming and outgoing file adapter. Also, when I add in my xsl file like u did in the xsl above, I find the side Fname source not mapped to Fname side destination in design mode.

  So, if you could please explain the logic to do these steps and why can't we just card only the fields that are necessary for the output (if we rae using xsd even).

  Kind regards

  SAIF

• Update of Standard vCOPS to business

  I have improved my license of Standard vCOPS to vCOPS for the view.  I did change the license and install the view on a Win 2008 R2 server adapter.  Everything seems to work fine, however, when I go to the environment > Configuration > adapter Instances...  I see the version Standard adapters.  Should I see here the version Enterprise adapters?  I need to reinstall or upgrade vCOPS the VAPP downloadable Standard version to the downloadable view VAPP vCOPS?

  Thanks - so I can confirm that everything is OK, it's just a description, which is static strings (does not change regardless of the license).

• How to add my 'fired' drive back to RAID1, PERC H710P and erase or foreign configurations...

  Hello

  I just got a PowerEdge T620. The OS is in RAID1 (two 256 GB SSD), controlled by a H710P PERC controller.

  When the computer was OFF, I took one of the discs, to see what it was the brand. (I bought the computer from a dealer and I wanted to just make sure I got what I paid for ). In any case, after you turn the computer back on, I noticed that the small screen at the front had changed color and showed a message. I checked the message and the computer seems to work with a disk in a single well. As it is supposed to.

  I decided to put the disc back in French - while the computer was OFF. I noticed, that at the start, the system is now saying:

  "Configuration foreign (s) found on adapter Press any key to continue, or 'C' load the configuration utility or the 'F' to import the foreign configuration (s) foreign and continue."

  I did a search on here and on Google and was able to find something that looks like a 'response' to me. However, as I have never done something like this before, I would like to ask you guys and see if I'm about to do the right thing!

  -When the system boots, press Ctrl-R.

  -I get to Setup BIOS card PERC H710P 4.00 utility - 0014

  -Then, I press 'Ctrl-N' until I get to the page "foreigners."

  -Once there, I insist on "PERC H710P adapter (Bus 5, Dev 0).

  -Once highlighted, I press 'F2 '.

  -After pressing 'F2', a window opens, which says 'Foreign Config'.

  -Then I press "ENTER" and another window opens with two options:

  'IMPORT' and 'CLEAR '.

  From what I have read, I need to select "DELETE?" Not sure if?

  Thank you

  G

  p.s. I downloaded photographs showing the PERC BIOS...

  

  

  Yes, what you call after having done, you must DELETE it, and then assigned as a hot spare.  If you import it, you will damage your table

• Qosimo F20: WLan adapter forget window allows you to configure the settings

  I recently changed a linksys wireless router to bt home hub but white since doing so I have been informed of bt, the wireless network adapter (intel (R) PRO/Wireless 2200BG Network adapter)

  I use keep forgetting window allows you to configure the settings. so every now and again I have to right-click on the icon in the lower right, choose View available wireless networks, click on change advanced configuration, and then click on the tab and then wireless networks check use windows to configure the box at the top left.

  I'm very novice all help would be appreciated.

  Post edited by: johnsmith3131

  Hello John

  As you know all configurations can be specific and depend on the used material. Believe me on this path it is not easy to say something concrete, because the BT home hub white is unknown to me and can I just suggest that you carefully read the user manuals which must be detailed explain how to connect external devices to the hub.

  By the way: you have something like this http://digital-lifestyles.info/display_page.asp?section=distribution&id=3404?

• VI LabVIEW Run-Time Engine adapter server configuration

  I want to connect to use the desktop execution trace toolkit to debug LabVIEW code modules using the adapter runtime TestStand.  How can I configure Server VI using LabVIEW VI in the LabVIEW Run-Time for TestStand engine adapter?

  Have you tried to create seqedit.ini (really .ini) or even in the directory of the executable that you use for the TestStand UI?

  -Doug