Configuration memory motherboard Formosa
I have a motherboard Formosa in a h8 1220 t hpe. The card mother specifys it supports pc3 12800 1600 mhz RAM however, I installed Gskill RAM with the above specifications and it appears at a speed of 1333 mhz.
is there anywhere in the BIOS I can configure what I haven't noticed?
Hello
The Formosa motherboard can run processors Intel Sandy Bridge or Ivy Bridge. If your PC has the Intel Sandy Bridge processor then 1333, this is all you will see. If you use the processor to Intel Ivy Bridge, then all DIMMs must be 1600 mhz DIMM (same CASE required) to make sure DIMMs will link upward to the maximum speed rating.
Customized motherboards will allow faster speeds with the DIMM using XMP, but generally the fastest speeds are overclocking the DIMMs. Even without the use of XMP in the faster speeds can be achieved using manual timing and adjusting the tension. HP does not cards mothers consumer overclocking choice except on rare occasions.
Tags: HP Desktops
Similar Questions
-
the EVGA GeForce GTX SC 760 will work on my h8 - 1360t with motherboard Formosa?
Maybe a silly question but will the EVGA GeForce GTX SC 76 working mother FORMOSA on a map?
Sticknrudder, welcome to the forum.
Not ridiculous at all in question. It is difficult to know which video cards work in computers of nowadays. I had to do a lot of research, including telephone calls to EVGA and XFX Support' are.
In this case, the video card will not work in your computer. All the GT to introduce 640 EVGA video cards require a complete UEFI BIOS into the motherboard. HP didn't start to use a complete UEFI BIOS until October 2012. Your computer was released in July 2011.
In addition, most of the newer cards will require a power supply unit (PSU) upgrade. It is, in other words, you have chosen the 460W or 600W PSU when you purchased the computer. Even the 460W may not be enough to power for some of the cards.
MSI makes a video card with a hybrid VBIOS with a switch to select an inheritance or a UEFI BIOS. There's a video in the link I provided just below the map image. Paul of Newegg has done a good job of explining map. I suggest you contact their Technical Support to ensure that it will work on your computer. It is 9.84 "in length. I suggest to make a model of the size of the card to ensure that it will not go in the space provided if they say that it will work.
Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.
-
Configuration memory of WebLogic
Hi guys,.
I know who are two ways to set up the memory used by WebLogic server:
- using setDomainEnv.sh
- using the administration console by putting the Arguments in server configuration start page.
I noticed that the command that starts the weblogic server contains entries of duplicates for Xms and Xmx MaxPermSize. The first has the value configured in the setDomainEnv.sh and the second has the value configured in the page 'stat server '. The command looks like:
/usr/JDK/instances/JDK1.7.0/bin/Java-serveur-D64 - Xms512m-Xmx1024m - XX: MaxPermSize = 512 m -Dweblogic.nodemanager.ServiceEnabled = true - Dweblogic.security.SSL.ignoreHostnameVerification = true - Dweblogic.ReverseDNSAllowed = false -Xms1024m-Xmx4096m -XX: MaxPermSize = 512 m
In this case, what value will be used for Xms and Xmx MaxPermSize?
Thank you
Radu
Hello
The last of the values.
-
Brief, illustrated by the guest is smaller than the configured memory
Hello
We organize our virtual machines with the external supplier and asked us to set the virtual host (RHEL) 1024 MB
At the end of that this has been done, I logged the guest and/cat/meminfo showed less than:
cat/proc/meminfo
MemTotal: 896108 kB
MemFree: 18848 kB
Buffers: 304120 kB
Cache: 378700 kB
SwapCached: 0 kB
Active principles: 253004 kB
Inactive: 486740 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 896108 kB
LowFree: 18848 kB
SwapTotal: 2097144 kB
SwapFree: 2097144 kB
Sale: 252 kB
Writeback: 0 kB
AnonPages: 56932 kB
Mapped: 14356 kB
Slab: 120860 kB
PageTables: 4008 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
CommitLimit: 2545196 kB
Committed_AS: 149664 kB
VmallocTotal: 34359738367 kB
VmallocUsed: 1784 KB
VmallocChunk: 34359736183 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
Hugepagesize: 2048 kB
I asked supplier what is the reason and that this was their response:
"Memory is less, on vm servers, because there is an overpass (128-200 MB), which is deducted from the total memory, if you need more RAM you ask accordingly."
This explanation does not seem right, because I think General cool knowledge happens on the hypervisor and comments should receive all the memory configured, if there are no limits set by resource management policies.
They sent me a screenshot of VMclient which shows
Memory: 1024 MB
Overhead: 104,53 MB
Use of the memory of the host: 855 MB
Memory usage comments: 471 MB
Is there a bad configuration on their side, or am I missing something here?
There may be a missunderstanding. When you assign 1024Mo to the guest who is the amount of memory the burst enables the OS. Point.
If you ask me, your provider is pulling on your legs.
Some useful links:
http://pubs.VMware.com/vi35/resmgmt/vc_rm__jumpstart.3.3.html
Find what
"Memory of the Virtual Machine.
Each virtual machine consumes memory based on its configured size, more the additional memory overhead for virtualization.
Configured size.
The configured size is a building maintained by the virtualization for the VM layer. This is the amount of memory that is presented to the guest operating system, but it is independent of the amount of physical RAM that is allocated to the virtual machine, which depends on the resource (shares, booking, limit) parameters explained below.
For example, consider a virtual machine with a configured size of 1 GB. When the guest operating system starts, he believes that it is running on a machine with 1 GB of physical memory. The actual amount of memory physical host allocated to the virtual machine depends on its resource settings memory and memory on the host ESX Server contention. In some cases, the virtual machine may charge the full 1 GB. In other cases, he could receive a small stipend. Whatever the actual distribution, the guest operating system continues to behave as if it is running on a machine with 1 GB of physical memory dedicated. "
here: http://pubs.vmware.com/vi35/resmgmt/vc_basic_mgmt.4.17.html
AWo
VCP / VMware vEXPERT 2009
\[:o]===\[o:]
= Due to a lack of employees, human beings humans are working here. -Treat it with care, they are rare. =
-
Satellite Pro A100 - 4 GB memory motherboard?
I have this model of Board of Directors: V000068460 there a docking port/blue graphics capabilities of the tooth/footprint/microphone/infra-red/external and pci-e connector for the wi - fi accepts cards pci-e dual use, but the system memory is limited to 3 GB because of the revision of the chipset.
So no one knows of a compatible Board that offers the same options (infra-red is optional) but has a later chipset revision so that the memory can use 4 GB or almost 4 GB of ram?
Hello
As far as I know the Toshiba Satellite Pro A100-196 PSAACE-001009AR supports 4 GB of RAM.
Google a little bit and found out that the Council V000068140 is compatible for Satellite Pro A100-196
Hope this helps
-
Game-VMRecourceConfiguration - MemLimitMB to the currently configured memory.
Hi guys
I'm about to determine the limit of the memory of all my virtual machines in a datacenter in Unlimited.
With this: (easy enough)
Get-data center-name "target Center" | Get-Cluster | Get - VM | Get-VMResourceConfiguration | where {$_.} {MemLimitMB - don't '-1'} | Game-VMResourceConfiguration - MemLimitMB $null
But don't really know how to approach the other way around.
$Details
$SettingsVM
$Details = get-data center-name "target Center" | Get-Cluster | Get - VM | Select Name, MemoryMB
$SettingsVM.Name = $Details.Name
$SettingsVM.MemoryMB = $Details.MemoryMB
Get-VM-name $SettingsVM.Name | Get-VMResourceConfiguration | where {$_.} MemLimitMB - eq $Null} | Game-VMResourceConfiguration - MemLimitMB $Details.MemoryMB
Thank you
John
Hi John,.
You can use the following script to PowerCLI for the opposite approach:
Get-data center-name "target Center" |
Get - VM |
{ForEach-Object
$VM = $_
$VM | Get-VMResourceConfiguration |
Where-Object {$_.} {MemLimitMB - eq - 1} |
Game-VMResourceConfiguration - MemLimitMB $VM. MemoryMB
}
-
Hello
I created a model of database with dbca (automatic configured memory management).
I want to create a base using this template, I've modified my template change the name of the database.
I run dbca in silent mode: dbca-silent - createDatabase-templateName - C:\temp\TEST.dbt - gdbname TEST - sid TEST
Once installation is complete, I noticed that memory_target = 0
Do you have an explanation?
Rgds,
Frédéric
Hi Frederic,.
See the TechNote MOS:
DBCA does not Ma set as default value for 11.2.0.3 What RAM > 4 GB (Doc ID 1453227.1)
Thank you
A H E E R X
-
County of total memory configured in each cluster
Hello
I'm pretty new still, Powershell and PowerCLI, but I'm learning.
I'm playing with, trying to extract data from my vCenter and its going well so far, with the help of this site and a lot of google'ing
But now im running into a bit of a problem, I want to count the total amount of memory configured in each cluster. And what I soleved with this code:
$confimem = get-Cluster |
Select Name,
@{N = 'Total configured memory GB'; E = {}
[Math]: round (($_ |)) Get - VM | %{$_. MemoryMB} |
Measure-object-sum | (Select sum - ExpandProperty) / 1 Ko, 1).
}}
And it gives a good result. But now I'm thinking it's account also all VM in the cluster, which is fed to the wide models and all that. I want to do is to include only the VM that is powered.
And I was thinking something like: Where-Object {$_.} PowerState - eq 'Receiving'}, but I'm not experienced enough to know how to put this together.
Any body help me solve this problem? I would be very happy
Nice day.
$confimem = get-Cluster | Select Name, @{N = 'Total configured memory GB'; E = {[Math]: round (($_ |))} Get - VM | Where-Object {$_.} PowerState - eq "Receptor"} | %{$_. MemoryMB} | Measure-object-sum | {{(Select-ExpandProperty Sum)/1 Ko, 1)}}
-
Hello
A virtual machine allows more memory than its configured memory?
For example:
ESXi host is to have 10 GB of memory. 2 VM are hosted on this. Dv01 & VM02 configured memory is 2 GB.
(1) if the Application is running inside the virtual machine requires more memory, then Will VM would be able to use memory configured 2 GB of memory conc as host is to have additional 6 GB of memory?
Hello
When you say 'configured memory', I guess you are trying to say that it is the memory that you have assigned as you created the virtual machine.
In this case, not your virtual machine cannot be used more than it is configured with. you increase the memory.
Please see below the link and image captured from pubs of vmware.
Hope that helps.
-
HP Pavilion dm4-1024tx Enterta: upgrade to 8 GB of memory and is blue screen problem
Product: HP Pavilion dm4-1024tx Entertainment Notebook PC
Product number: XC651PA
I have corsair Vengeance ram 8 GB (CMSX8GX3M1A1600C10) that as a result of the configurations as mentioned below:
SPD 9-9-9-24 latency
SPD speed 1333 Mhz
SPD voltage 1.5V
PC3-12800 (1600 MHz) memo speed
Tested latency 10-10-10-27
Tested 1600 Mhz speed
Tested voltage 1.5V
It passes the test of memory BIOS.
BIOS VERSION: Hewlett-Packard F.27, 21/12/2011
But when I boot windows 7, it shows the windows symbol and then it shows the blue screen with the error
STOP: 0X0000007E
If I replace memory corsair with the memory that has been delivered with the laptop the system only works very well.
Corsair memory is not compatible with the system?
I have a dual boot and installed ubuntu on this subject. Ubuntu loads perfectly fine, but after a while the system restarts automatically (IE open application).
I tried memorytest86 to test the memory, but the application continue to crash and reboot and does not provide any results.
Help, please.The RAM is not compatible. The system allows a maximum total memory of 8 GB and uses DDR3-1333 which downclocks at 1066 speed. You cannot use a single module of 8 GB. 4 gigs is the large single module supports the system. I suspect the memory that you have will work fine if you had modules of 2 x 4 GB instead of a single module of 8 GB. That's why memtest is not finished. The controller memory motherboard is not able to take up 8 GB of RAM by a single channel.
-
HP Probook 4520 s memory 8 GB (2x4gb) Corsair pass without success and failure
OK, here's the story
My laptop is HP Probook 4520 s
with Windows Windows 8.1 (6.3) 64-bit (Build 9600)
Please see the end of this post for CPU - Z report of specs.
Currently I have 3 GB of memory installed - had to install their return after failed upgrade.
Please check back the CPU - Z report for the memory module specifications.
I bought the memory pack 2 x 4 GB Corsair following
Corsair CMSO8GX3M2A1333C9 8 GB (2x4gb) 1333 MHz DDR3 SODIMM
http://www.scorptec.com.au/product/memory/SODIMM/43657-CMSO8GX3M2A1333C9
Plug new modules:
Lifetime warranty
Size 8 GB (2 x 4 GB) Kit
Performance profile none
Fan included no.
Heat spreader-
Configuration memory dual channel
Type of DDR3 memory
Package - memory Pin 204
Package - Format memory SODIMM
Tested voltage 1.5
SPD tension 1.5
PC3-10600 (1333 MHz) memo speed
SPD speed 1333 MHz
Tested speed 1333 Mhz
Tested latency 9-9-9-24
SPD 9-9-9-24 latencyWhen I installed the memory module on the laptop, I couldn't go essentially exceed the stage of the POST. Is the HP logo appears on the screen and what is it... That's all... nothing beyond this point.
When I went to the BIOS settings, memory read 81xxMB successfully, it is essentially 8 GB of RAM.
I tried to reset the BIOS settings, has not yet.
I removed the 2 x 4 GB modules, put back the two original modules of 1 GB and 2 GB - those who came with the laptop-, everything worked again.
What was not right here... ?
PS please don't answer not with lame answers "it's weird", "that's strange", I know it's weird and strange. I want clear and specific suggestions.
Report of CPU - Z below:
TXT of CPU - Z report
-------------------------------------------------------------------------Binary files
-------------------------------------------------------------------------CPU - Z version 1.69.0.x64
Processors
-------------------------------------------------------------------------Number of processors 1
Number of threads 4APICs
-------------------------------------------------------------------------Processor 0
-Core 0
-Wire 0 0
-Thread 1 1
-Core 2
-0-4 wire
-Wire 5 1Timers
-------------------------------------------------------------------------Timer ACPI 3,580 MHz
Timer HPET 14,318 MHz
Timer perf 2,208 MHz
Sys 1,000 KHz timer
Timer 133,02 MHz BCLKInformation for processors
-------------------------------------------------------------------------Processor 1 ID = 0
Number of cores 2 (max 8)
Number of threads 4 (max. 16)
Name Intel Core i5 430M
Code-named Arrandale
Specification Intel (r) Core i5 CPU M 430 2.27 GHz
Package (platform ID) Socket 989 rPGA (0x4)
CPUID 6.5.2
CPUID long 6.25
Core Stepping C2
The 32nm process technology
TDP limit 25 Watts
Basic speed 2527,3 MHz
Multiplier x Bus 19.0 x 133.0 MHz speed
2394,3 MHz rated Bus speed
Stock frequency 2266 MHz
Instructions sets MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, EM64T, VT - x
Data L1 cache 2 x 32 KB, size 8-way line set associative, 64 bytes
L1 instruction cache 2 x 32 KB, size 4-way set associative line, 64 bytes
L2 cache 2 x 256 KB, size 8-way line set associative, 64 bytes
Cache 3 MB L3, size 12 channels line set associative, 64 bytes
FID/VID control YesTurbo Mode supported, enabled
2533 MHz Max turbo frequency
Max-non-Turbo report 17 x
Max turbo report 19 x
Rate of return max 9 x
TDC limited 21 amps
Basic NT 21 Watts
Uncore PDT 4 Watts
Power @ 9 x 7 Watts
Power @ 10 x 8 Watts
Power @ 11 x 9 Watts
Power @ 12 x 11 Watts
Power @ 13 x 13 Watts
Power @ 14 x 15 Watts
Power @ 15 x 18 Watts
Power @ 16 x 21 Watts
Power @ 17 x 25 Watts
Number of bus max 255
PCI peripheral device connected to the 255 bus, device 2, function 1Chipset
-------------------------------------------------------------------------Northbridge Intel Havendale/Clarkdale Host Rev. Bridge. 12
Southbridge Intel HM57 Rev. 06
Graphics interface PCI-Express
Width link PCI-E x 16
PCI-E Max Link width x 16
Type of DDR3 memory
Memory size 3 GB
Double channels (symmetrical)
Frequency 532,1 MHz memory (04:16)
Latency CASE # (CL) 7.0
RAS # for CASE # delay (tRCD) 7
RAS # Precharge (tRP) 7
Cycle Time (tRAS) 20
Time to Row Refresh Cycle (tRFC) 60
Control rate (CR) 1 t
Base address e/s MCHBAR 0x0FED10000
E/s MCHBAR size 4096
MCHBAR recordsDMI
-------------------------------------------------------------------------DMI BIOS
vendor Hewlett-Packard
version 68AZZ version F.0F
Day 18/02/2011
ROM size 2560 KBSystem DMI information
Manufacturer Hewlett-Packard
product HP ProBook 4520 s
Unknown version
series 2CE0211M4C
UUID {1520830E-6A57-11DF-8C36-42C05900004D}
SKU WS879EA #ABV
family 103C_5336ANDMI Baseboard
vendor Hewlett-Packard
model 1411
review of KBC Version 57,34
series 2CE0211M4CDMI system box
Manufacturer Hewlett-Packard
chassis type Notebook
2CE0211M4C series chassisDMI processor
Manufacturer Intel(r) Corporation
model Intel (r) Core i5 CPU M 430 2.27 GHz
clock speed 2264,0 MHz
The FSB 133.0 MHz speed
multiplier x 17.0DMI Extension slot
PCI SLOT1 designation
type of PCI
32-bit width
No. populatedDMI OEM channels
String [0] 70/71 79 7 ABS has 7 b 7 c
v01.4A CSM chain [1]
chain [2] www.hp.comDMI physical memory matrix
location motherboard
use system memory
correction no
Max 8192 MB capacity
Max # of devices 2DMI memory device
name high-Slot 1 (top)
format SODIMM
unknown type
width total 64-bit
64-bit data width
Size 2048 MBDMI memory device
name high-Slot 2 (under)
format SODIMM
unknown type
width total 64-bit
64-bit data width
size 1024 MBStorage
-------------------------------------------------------------------------Drive 0
Device path \\?\scsi#disk&ven_&prod_st9320423as#4&1f4bc32b&0&000000#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
Type set
Name ST9320423AS
Capacity GB 298,1
SMART Support YesUSB devices
-------------------------------------------------------------------------Generic USB hub USB Device class = '0 x 09' subclass = 0 x 00, seller = 0 x 8087, product = 0 x 0020
Peripheral USB device USB Composite class = '0xEF' subclass = 0 x 02, seller = 0 x 0461, product = 0x4DB6
Generic USB hub USB Device class = '0 x 09' subclass = 0 x 00, seller = 0 x 8087, product = 0 x 0020
Peripheral USB Microsoft mouse and detection (USB) keyboard driver, class = "0x00" subclass = 0 x 00, vendor = 0x045E, product = 0 x 0745Graphics
-------------------------------------------------------------------------Number of cards 1
API chart
-------------------------------------------------------------------------ATI I/O API
Graphics cards
-------------------------------------------------------------------------Display adapter 0
Name ATI Mobility Radeon HD 4500 Series (Microsoft Corporation - WDDM v1.1)
Manufacturer 0x103C (0 x 1411)
512 MB memory size
Bus device PCI 1 (0x1), device 0 (0x0), function 0 (0x0)
Vendor ID 0 x 1002 (0x103C)
The model 0 ID 9555 x (0 x 1411)
Performance level 0Win32_VideoController AdapterRAM = 0x20000000 (536870912)
Win32_VideoController DriverVersion = 8.97.10.6
Win32_VideoController DriverDate = 20/06/2012Software
-------------------------------------------------------------------------Windows Version Microsoft Windows 8.1 (6.3) 64-bit (Build 9600)
Version of DirectX 11.0Clear and precise. Your laptop uses the memory of 1.35 volts and that you have installed 1.5 volt.
This is the crucial page for memory you need:
http://www.crucial.com/store/listparts.aspx?model=ProBook%204520s
If it's 'the Answer' please click on 'Accept as Solution' to help others find it.
-
Pavilion dvr7: upgrade memory for laptop
Hello forum could use some advice. My laptop is a (product of HP Pavilion dv7 notebook # XH108UAR #ABA) currently has two (2 GB 2Rx8 PC3-10600 s - 09-10-F2) of the memory installed modules in it. Can they be improved and replaced with the following memory modules:
Kingston ValueRAM 4 GB Notebook Memory Module - 1333 MHz, DDR3 PC3-10600, SODIMM, CL 9, 204 pins, 1.5V - KVR13S9S8/4
If the answer is "Yes"; This will make a significant difference when it comes to operating speed and the ability to play some of the newer games that require more memory to play. If this isn't the good memory to upgrade my laptop with what I need and how much memory can I add to my system. Your advice would be greatly appreciated. Thanks in advance!
FJG1
Hello
The value maximum supported are 8 GB (2 x 4) DDR3 SODIMM.
Manual
http://h10032.www1.HP.com/CTG/manual/c02642701
Supports up to 8 GB of RAM in the following configurations
Memory ● total system of 8192 MB (4096 MB × 2, both channels)
System memory total 6144 ● MB (4096 MB × 1 + 2048 MB × 1)
Memory ● system total of 4096 MB (2048 MB x 2, dual-channel)
Memory 4096 MB total system (4096 MB × 1) ●The problem of the KVR modules is that sometimes does not work, if you are in the United States, one of the most interesting options is Crucial 1.35v - 1.5V DDR3 memory dual voltage
http://www.crucial.com/USA/en/compatible-upgrade-for//Pavilion-dv7-4171us
-
Pavilion dv2700tv: memory upgrade
BTW, my Pavilion dv2700tv processor is core 2 duo Intel 9300 2.5 mhz, 6 MB of L2 cache.
Can I place DDR2 DDR3 memory?
Thank you
Pogostyx
Hello:
Unfortunately, you can not.
DDR, DDR2 and DDR3 memory run on different voltages and are cross with each other.
The notches are cut in different places to prevent people to install the wrong chip in a PC which would result in damage to the strip of memory, motherboard of the PC, or both.
-
I'm losing configuration when I turned off my Cisco 857 router
I bought the new router Cisco 857 of the shop. Router must have been used before as I couln can't go inside with name of user and password default cisco/cisco.
Well I followed digital and reset the password for the user name and password. Now I have finally connected to Cisco CP express on my IE browser.
I discovered that someone was using a router in the shop that's why I countries: ' t log in to him in the first place. In any case the problem is that when I changed my configuration and applies the settings he remembers until I turned off. When I turn on again he remembers all the parameters of this shop.
He returned everything back: IP address, former account to level 15 and password - just like after the password reset.
I tried again and he again lost the settings. So I found instructions:
http://www.Cisco.com/en/us/products/HW/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed once again all the settings of the router. My settings are still lost after the power on/off. I noticed that when I do everything first bit it shows
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enable
Cisco#show start
Using 3359 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.
!
no aaa new-model
!
crypto pki trustpoint TP-self-signed-3185909327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3185909327
revocation-check none
rsakeypair TP-self-signed-3185909327
!
!
crypto pki certificate chain TP-self-signed-3185909327
certificate self-signed 01 nvram:IOS-Self-Sig#5.cer
dot11 syslog
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
ip cef
no ip domain lookup
ip domain name molinary.com
!
!
!
username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.
username username privilege 15 password 0 password
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
description $ES_WAN$
ip nat outside
ip virtual-reassembly
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$
ip address 10.10.10.1 255.255.255.248
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer0
ip address dhcp
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname [email protected]/* */
ppp chap password 0 netgear01
ppp pap sent-username [email protected]/* */ password 0 netgear01
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface ATM0.1 overload
!
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username
privilege 15 secret 0 Replace
and with the username and password you want to use.
-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
end
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#show version
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Cisco uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
Cisco#
Cisco#
Cisco#
Cisco#end
Translating "end"
% Unknown command or computer name, or unable to find computer address
Cisco#reload
Proceed with reload? [confirm]
*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. R
eload Reason: Reload Command.
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memory
Booting flash:/c850-advsecurityk9-mz.124-15.T12.bin
Self decompressing the image : ############################################## [O
K]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
Image text-base: 0x8002007C, data-base: 0x814E7240
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
no ip dhcp use vrf connected
^
% Invalid input detected at '^' marker.
SETUP: new interface NVI0 placed in "shutdown" state
Press RETURN to get started!
*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Initialized
*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Enabled
*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o up
*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoing
a cold start
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, chan
ged state to down
*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Ac
cess1, changed state to up
*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
nged state to up
*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administ
ratively down
*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administ
ratively down
*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state to
up
*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state to
up
*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state to
up
*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to down
*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et3, changed state to down
*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et2, changed state to down
*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et1, changed state to down
*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to upAuthorized access only!
===========================================
Please help me as I am stuck and can't go any further....
Hi Dragan,
After you run the wizard Cisco CP Express, it should save the configuration set to update the flash on the router. However, in your case, it seems this is not the case. Therefore:
- Configure the device via Cisco CP Express--> do NOT turn off after that
- Connect to the router with Hyperterminal. Enter the configuration mode by typing:
Enable
When you are prompted for a password to put in. The line should now be router #.now type:
write memoryYou see errors? Otherwise, type:
See the startup-configCheck the output matches the configuration you've tried. If Yes, then you are good to go. If this is not the case, let us know all the errors you received.
-
Option not available in Configuration Professional v2 performance routing
I get a router Cisco 2901 put in place and tries to load balancing/link aggregation and/or failover for my double WAN connections. Being new Cisco's IOS software, I'd rather do my setup using the specialist graphic Configuration interface. If I understand correctly, the option of routing Performance will help me set up but I don't have this option, available in professional Configuration; any ideas? I downloaded the latest version of CP (version 2) I think; I've been reviewing on the article often referenced on this feature to: Cisco Routing of Performance and reviewed the Cisco Feature Navigator available on http://www.cisco.com/go/cfn for my release IOS; the feature I'm looking for is documented in a flash to http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/PfR/CCPPFR.swf (screenshot below) presentation:
A summary of key results of the command show version 'IOS' on this router are:
Cisco IOS software, software C2900 (C2900-UNIVERSALK9-M), Version 15.0 (1) M, VERSION of the SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc.
Last update Wed, 30-Sep-09 05:30 by prod_rel_team
ROM: System Bootstrap, Version 15.0 M1 (1r), VERSION of the SOFTWARE (fc1) BPRouter availability is 5 days, 23 hours, 43 minutes system returned to ROM by system restarted at 11:34:47 PCTime Wed Dec 23 2009 system image file is "flash0:c2900-universalk9-mz.» Spa. 150 - 1.M.bin.
Cisco CISCO2901/K9 (revision 1.0) with 483328 K/K 40960 bytes of memory.
Card processor ID FTX134981A3
2 FastEthernet interfaces
2 gigabit Ethernet interfaces
1 module of virtual private network (VPN)
Configuration of DRAM is wide with parity 64-bit capable.
255K bytes of non-volatile configuration memory.
254464K bytes of system CompactFlash ATA 0 (read/write)
License info:
License IDU:
-------------------------------------------------
Device SN # PID
-------------------------------------------------
* 0 FTX134981A3 CISCO2901/K9
Technology for the Module package license information: "c2900.
----------------------------------------------------------------
Technology-technology-current package Type next reboot technology
-----------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
Security securityk9 Permanent securityk9 data uc no no no register None None None Configuration is 0 x 2102
Thank you for your question. This community is for Cisco Small Business products, and your question is referring to a product Cisco Elite/Classic. Please post your question in the Cisco NetPro forums located here: https://supportforums.cisco.com/community/netpro?view=overview this forum is subject to the subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
Kind regards
Cindy Toy
Cisco Small Business Support Community Manager
Maybe you are looking for
-
IM signed in devices that I don't own? I'm so confused right now, it's complicated! I help to remove them, and I bought an iPad 2 Air, but have not used until I have this problem!
-
40.0.2 Firefox crashes at the opening.
Have tried a new installation on several computers Windows 7 Enterprise. All crash instances 40.0.2 Firefox on opening the program. Only solution is to save the version 39 rev and tell him no to automatic update.
-
Why I can't find the application 'News' coming on iOS 9 on my iPhone 5s?
Why can't the 'News' app on my iPhone 5s?
-
I want to do more than one check box at run time. So I did it with listbox, but I can't check it out. How can I do? Help, please I have attached my VI. Thanks in advance.
-
syswin7u8.exe - on w700p anyone know of him?
Malwarebytes picked up malware a few days ago, took care of some objects. Tonight, cpu was running hot and hard, push this file was it (syswin7u8.exe). Google and a page on the malware came. We found two directories that belong so deleted. One was sy