Configuration of Radius Exception

Similar Questions

• Configuration of RADIUS and accounting AAA + PIX-515E

  Dear All;

  I want to put the accounting of PIX.

  Here is the composition of the equipment.

  ACS SE: 4.1.1.23.5

  PIX 515E: 7.0 (6)

  PIX of setting is as follows.

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + host xx.xx.xx.xx

  key xxxxx

  order of accounting AAA GANYMEDE +.

  Console telnet accounting AAA GANYMEDE +.

  Thus, the configuration setting was written in ACS.

  But the user name is enable_15. (attached 1.jpg)

  Is it a restriction?

  Kind regards

  Reiji

  Hi Marilou,

  Looks like we have the authority to command configured on the pix. You must enable authentication configured on the RADIUS server then only we would get username is accounting, unlike pix Device IOS doesn't send user name to the RADIUS server, he would send enable_15 as username for all users.

  Configure the following command to make it work.

  AAA authentication enable console LOCAL + Ganymede

  HTH

  -Philou

• ACS - 4.1 - does not display Radius (Nortel) in the configuration of the Interface

  We have a GBA running on Windows we can see the Radius (Nortel) option in the Configuration of the Interface.

  Anyone deal with this issue?

  It's probably because you don't have any AAA devices configured for RADIUS (Nortel). IF you set one, it will appear in the configuration of the interface

  Nicolas

  ===

  Remember responses of the rate that you find useful

• In Active/Passive Mode Radius server configuration

  We set up (active/active) the two ASA load balancing.  We also configure two Radius servers with load balancing.  At present, the Radius servers are configured with active/active.  Is it possible to configure a Radius Server with (active/passive)?

  RADIUS protocol Radius AAA server
  AAA-server Radius (inside) host XXX.XXX.XXX.XXX
  Timeout 300
  key *.
  RADIUS-common-pw *.

  AAA-server Radius (inside) host XXX.XXX.XXX.XXX
  Timeout 300
  key *.
  RADIUS-common-pw *.

  AAA accounting enable console RADIUS

  Thank you.

  Diane

  Diane,

  Well I'm still not 100% sure that you understand exactly what is happening. Normally, on a single ASA, authentication is always performed on the same radius server until it fails (i.e. active/passive as you call it).

  Now, you mention that you have 2 ASAs in load balancing, so I don't know if you mean that:

  (1) 2 users that connect to the same ASA get authenticated by radius 2 servers different (should never happen)

  or

  (2) when 2 users connect to the cluster, user1 gets redirected to ASA1 and authenticated on Radius1, while User2 will be redirected to ASA2 using Radius2 to auth. This could be normal if both ASAs are set up differently (defined in a different order radius servers) or an ASA had a problem connecting to Radius1, at some point and so it considered out of service.

  In any case, 'sh aaa-server protocol radius' and 'debug RADIUS' can help determine why an asa individual does not use (initially configured) primary radius server.

  HTH

  Herbert

• App Server 5.2 & RADIUS

  We have a Mac Mini server (macOS 10.12) with configured App (5.2) Server (active Directory and DNS Server Services Open, the network is on a static IP). We used to have an Airport Extreme set from the application server, with providing RADIUS authentication server.

  Now, we would like to add other extreme BaseStation from the airport to the network expand its range. We were already able to add another customer through Admin Tool Radius RADIUS. But, of course, access to the network via the second access point does not work.

  Application server is a really strange, because he gives, in many areas, rudimentary and owners is responsible for a large number of technologies, but if you want something you sort of a fall application server services. For example the App Server WebServices collide with advanced options for Apache, passenger, etc., once you try to configure something advanced Web services stop working. I hope that we will get configuration of the advanced features of future iterations. That's what concerns me here: Server App, basestations integration integration server App and RADIUS with several Airport Extreme BaseStation.

  1. as a result, I would like to know what kind of RADIUS support App Server provides it?

  2. Since the addition of a second Airport base station does not work, I guess I'll have to configure a RADIUS server outside the server application, probably as a result of this video: https://vimeo.com/53774350?

  3. but what happens to Airport base Station of the application server configuration, I was active for the first base station? Can I still configure Services and the server mapping App?

  4. should I maybe keep the base activated in App Server station, but disable the requirement of authentication via WiFi and configure a separate RADIUS server?

  5. What is the certificates: App Server already has a global certificate, I can use this instead of building a new one?

  6. the access group will be visible in App Server?

  I hope someone can help.

  When I "sudo radiusconfig - methods", I get:

  {

  clientcount = 2;

  set = 1;

  'eap.conf' = {}

  'CA_file' = ' / etc/certificates/server.seju.eu.xxxxxxxxxx.chain.pem ';

  Wilson = "/ Library/Server/RADIUS/raddb/certs".

  certdir = ' / Library/Server/RADIUS/raddb/certs ".

  'raddbdir' = ' / etc/certificates/server.seju.eu.xxxxxxxxxx.cert.pem ';

  "check_cert_cn" = "% {user name} ';

  "check_crl" = no;

  'raddbdir' = ' / Library/Server/RADIUS/raddb/certs/dh;

  'fragment_size' = 1024;

  "include_length" = yes;

  'private_key_file' = ' / etc/certificates/server.seju.eu.xxxxxxxxxx.key.pem ';

  "private_key_password" = "Apple: UseCertAdmin";

  'raddbdir' = ' / Library/Server/RADIUS/raddb/certs/random ";

  };

  'radiusd.conf' = {}

  AUTH = no;

  "auth_badpass" = no;

  "auth_goodpass" = no;

  'cleanup_delay' = 5;

  confdir = "/ Library/Server/RADIUS/raddb;

  'exec_prefix' = ' / Applications/Server.app/Contents/ServerRoot/usr ';

  "hostname_lookups" = no;

  localstatedir = "/ private/var;

  LogDir = "/ private/var/log/radius";

  "max_request_time" = 30;

  'max_requests' = 1024;

  prefix = ' / Applications/Server.app/Contents/ServerRoot/usr ';

  radacctdir = "/ private/var/log/RADIUS/radacct."

  certificate_file = "/ Library/Server/RADIUS/raddb;

  sbindir script configures = "/ Applications/Server.app/Contents/ServerRoot/usr/sbin";

  sysconfdir = "/ Library/Server/radius";

  };

  }

  When I "sudo radiusconfig - naslist", I get

  sudo radiusconfig - naslist

  customer IP.xxx.xxx.xxx {}

  secret = YYYYYYYYYY

  ShortName = "Base Station 1.

  Community =

  type = 'AirPort base station.

  Description =

  };

  customer IP.xxx.xxx.xxx {}

  secret = ANACHID

  ShortName = "Base Station 2.

  Community =

  type = 'Airport base station.

  Description =

  };

  Post edited by: Konstrukteur

  After some research, I got it to work. I went through all the steps in the video less access group. I guess my problem was obtaining the new base station, after be spent during the installation of the second base station and reset, everything works now! I also corrected some certification of related problems. I used the excellent Admin Tool Radius that is set correctly. Bad adjustment could have been the cause of my troubles!

  (1) I would like to know what kind of RADIUS support App Server provides it?

  It seems to provide a full support.

  (2) given that the addition of a second Airport base station does not work, I guess I have to configure a RADIUS server outside the server application, probably as a result of this video: https://vimeo.com/53774350?

  Always excellent tutorial, a bit outdated in macOS Sierra. My RADIUS server was already running a full server.

  (3) what happens to Airport base Station of the server application configuration I was active for the first base station? Can I still configure Services and the server mapping App?

  It works in our case

  (4) should I keep the base activated in App Server station, but disable the requirement of authentication via WiFi and configure a separate RADIUS server?

  It works in our case. No need to put in place the Radiusserver again. My incomplete Radius Server was probably a related problem of certification.

  (5) what about certificates: App Server already has a global certificate, I can use this instead of building a new one?

  Ray will use the certificate used in the server application. I used the excellent Admin Tool Radius to implement.

  (6) the access group (which is mentioned in the video) will be visible on the App?

  If you choose "view system accounts" under Server > discover then it should appear. But there is no need to access group, as RAY will use Opendirectory.

  If everything is working now. As I said I went over the steps alone once again, the problem I had, was probably related to the certificate or an error in the configuration of the Client.

  Now, I just have to find a way to get the RADIUS in Console logs, since they do not appear here in macOS Sierra!

• rv180 has no RADIUS under security option

  We used RV180W devices and the security, there is an option to configure a RADIUS server (we use it to authenticate the IPSEC VPN with Active Directory connections).

  We have installed a RV180 (wireless) and it seems to be missing the RADIUS configuration options.  Documentation is not State of RADIUS is not supported on the RV180.  Indeed, it involves two models should support this feature (page1 under strong security).

  http://www.Cisco.com/c/dam/en/us/products/collateral/routers/rv180-VPN-r...

  I applied the last (to date) version 1.0.4.14 without change.  On a whim, I checked some of the other RV180 we installed and found the RADIUS was missing in a RV180 with 1.0.3.10 firmware too, yet all versions of RV180W we made do.

  This is a firmware build feature that was "missed" and never caught or documentation does not reflect the features actually supported or has been deleted after the liberation (false advertising in my humble OPINION).

  I do not consider the RADIUS authentication an exclusive feature in wireless technology.

  Has anyone else encountered this problem?  RADIUS is supported on the RV180 and if so, how can I access these settings?

  Ref: Cisco Support box 630249873

  With the support of Cisco, I confirmed that it is a feature not in the firmware RV180.

  Adding to the next version maybe not possible then Cisco opted replaced my unit with a RV180W that supports the RADIUS authentication (an offer I think).

  Cisco did not specify if the RADIUS feature will be added to the RV180 firmware (or not) in the future.  Thus, the documentation will be updated to reflect the current functionality or a future update can add this feature to the RV180.  My advice would be to check the most recent firmware release notes if you need this feature or get the RV180W instead if you consider the RV180.

  So far, my experience with the RV180W was satisfactory (although the web gui is slow sometimes).  I also used the RV110 and found the VPN settings exposed on that to be very limited in comparison.  I choose to use the vpn ipsec shrewsoft client with of the RV180W rather than the fast Cisco VPN client (which seems not to connect more than not).

• Shell exec user permission on ASA using IAS radius

  With the help of ASA 5540 - 8.0 (4) & trying to get approval for Shell EXEC (15) for the authenticated user fron IAS radius server. Used on the SAA aaa authorization command & specified attributes on the IAS radius as shown in the configuration guide, but still the user will be deposited into default exec level. I need to use the enable command to get the user to the privilege level of exec.

  Hi all

  Although the 'Exec authorization command' was introduced into the code ASA 7.1 the ASA does not support the feature AAA Exec permission yet, so it cannot be configured with RADIUS or GANYMEDE.

  The enhancement request has already been filed on it.

• RADIUS does not pray attribute filling 4 (NAS-IP-Address)

  I'm trying to get a Cisco 3120 G configured for RADIUS authentication.  I have a lot of other IOS devices with identical configuration of work lines, however, it gives me a hard time.  The strategy of the RADIUS server is configured by NAS-IP-Address.  The configuration of the AAA and RADIUS is as follows:

  AAA new-model
  AAA authentication login default local radius group
  AAA authorization exec default local radius group

  host 10.x.x.x auth-port 1645 1646 RADIUS server acct-port
  Server RADIUS ports source-1645-1646
  Server RADIUS button 7 XXXXXXXXXXXXXX

  See the Flash following debugging information:

  indrc3120a #.
  000284: 8 Feb 14:05:15.447 PST: RADIUS: Pick NAS IP for you = 0x5992EF4 = 0 cfg_addr = 0.0.0.0 tableid
  000285: 8 Feb 14:05:15.447 PST: RADIUS: ustruct sharecount = 1
  000286: Feb 8 14:05:15.447 PST: RADIUS: success radius_port_info() = 1 radius_nas_port = 1
  000287: Feb 8 14:05:15.447 PST: RADIUS (00000000): send 10.x.x.x:1645 id 1645/8, len 84 access request
  000288: Feb 8 14:05:15.447 PST: RADIUS: authenticator 12 5th 7th DF 01 B5 F1 D8 - 40 07 09 76 88 C1 A4 C5
  000289: 8 Feb 14:05:15.447 PST: RADIUS: NAS-IP-Address [4] 6 0.0.0.0
  000290: 8 Feb 14:05:15.447 PST: RADIUS: NAS-Port [5] 6 2
  000291: Feb 8 14:05:15.447 PST: RADIUS: NAS-Port-Type [61] 6 virtual [5]
  000292: 8 Feb 14:05:15.447 PST: RADIUS: username [1] 13 "admin_user '.
  000293: 8 Feb 14:05:15.447 PST: RADIUS: Calling-Station-Id [31] 15 "10.y.y.y".
  000294: 8 Feb 14:05:15.447 PST: RADIUS: User-Password [2] 18 *.
  000295: 8 Feb 14:05:15.505 PST: RADIUS: receipt id 1645/8 10.x.x.x:1645, Access-Reject, len 20
  000296: 8 Feb 14:05:15.505 PST: RADIUS: authenticator 4th EC 8F AB BB 8th F9 BB - 13 67 56 A3 5F F9 99 94
  000297: Feb 8 14:05:15.505 PST: RADIUS: saved the data of permission for the user 5992EF4 to 0

  Note the NAS-IP-Address populated as 0.0.0.0 attribute

  Another switch with an identical Setup returns the following:

  tritc3120a #.
  350554: 8 Feb 14:11:00.916 PST: RADIUS / ENCODE (000155BC): ask "" user name: ".
  350555: 8 Feb 14:11:10.605 PST: RADIUS / ENCODE (000155BC): ask "" password: ".
  350556: 8 Feb 14:11:14.480 PST: RADIUS/ENCODE (000155BC): orig. component type = EXEC
  350557: 8 Feb 14:11:14.480 PST: RADIUS: AAA Attr not supported: interface [170] 4
  350558: 8 Feb 14:11:14.480 PST: RADIUS: 74 74 [tt]
  350559: 8 Feb 14:11:14.480 PST: RADIUS / ENCODE (000155BC): down the type of service, "radius attribute 6 sur-pour-login-auth server" is disabled
  350560: 8 Feb 14:11:14.480 PST: RADIUS (000155BC): Config NAS IP: 0.0.0.0
  350561: 8 Feb 14:11:14.480 PST: RADIUS / ENCODE (000155BC): acct_session_id: 87482
  350562: 8 Feb 14:11:14.480 PST: RADIUS (000155BC): send
  350563: 8 Feb 14:11:14.480 PST: RADIUS/ENCODE: Best 10.x.x.x address IP Local to the 10.y.y.y Radius Server
  350564: 8 Feb 14:11:14.480 PST: RADIUS (000155BC): send 10.y.y.y:1645 id 1645/222, len 90 access request
  350565: 8 Feb 14:11:14.480 PST: RADIUS: authenticator 5F B1 17 DF 72 4B 3D - B6 D8 5 85 66 B9 8 d 7 c A6
  350566: 8 Feb 14:11:14.480 PST: RADIUS: username [1] 13 "admin_user '.
  350567: 8 Feb 14:11:14.480 PST: RADIUS: User-Password [2] 18 *.
  350568: 8 Feb 14:11:14.480 PST: RADIUS: NAS-Port [5] 6 2
  350569: 8 Feb 14:11:14.480 PST: RADIUS: NAS-Port-Id [87] 6 'tty2 '.
  350570: 8 Feb 14:11:14.480 PST: RADIUS: NAS-Port-Type [61] 6 virtual [5]
  350571: 8 Feb 14:11:14.480 PST: RADIUS: Calling-Station-Id [31] 15 "10.z.z.z".
  350572: 8 Feb 14:11:14.480 PST: RADIUS: NAS-IP-Address [4] 6 1.2.3.4
  350573: 8 Feb 14:11:14.556 PST: RADIUS: receipt id 1645/222 10.y.y.y:1645, Access-Accept, len 83
  350574: 8 Feb 14:11:14.556 PST: RADIUS: authenticator 24 D9 F9 E2 BB A3 66 F6 - 73 E8 5 42 8 A5 17 DA
  350575: 8 Feb 14:11:14.556 PST: RADIUS: Type of Service [6] 6 Administrative [6]
  350576: 8 Feb 14:11:14.556 PST: RADIUS: [25] in class 32
  350577: 8 Feb 14:11:14.556 PST: RADIUS: 59 B1 6 06 00 00 01 37 00 01 0a 1st DC 18 01 CB C7 B8 D7 82 CA E2 00 00 00 00 00 00 00 0b [Ym7]
  350578: 8 Feb 14:11:14.556 PST: RADIUS: seller, Cisco [26] 25
  350579: 8 Feb 14:11:14.556 PST: RADIUS: Cisco-AVpair [1] 19 "shell: priv-lvl = 15.
  350580: 8 Feb 14:11:14.556 PST: RADIUS (000155BC): receipt of id 1645/222

  Note that in the above example, the NAS-IP-Address is feeding properly (I just the changed for security reasons)

  If anyone has any advice, it would be greatly appreciated.  Does the switch need a restart? Blow RADIUS server process?

  Thank you

  CSCdx27019">."
  

  Seems to be a bug,

  CSCdx27019    Pkt sent by CSS access RADIUS request contains no information NAS

  The feature of Cisco ACS NAR (restricted access network) with RADIUS does not work with CSS. This is because the radius NAS-IP-Address attribute is set to 0.0.0.0 in the Radius authentication request.

  Rgds, jousset

  Note the useful messages

• ACS 5.2 - Support for RADIUS attributes per user

  Hi all

  Does anyone know if it is possible to configure the RADIUS attributes on a per user in GBA 5.2 basis?

  That was possible under ACS 4.x, however, that I can't seem to find reference if ACS5.2 supports.

  Thank you

  Leon

  You can do this by setting by using attributes and then by substution attribute.

  You can see an example of it to set an internal user attribute to use as the value for the field address-IP-box

  This is just an example and can be applied also to any attribute RADIUS in which set an attribute of the user of the same type. Values can also be taken from an external identity as AD store

• RADIUS server for authentication

  Hello

  I want to configure the radius server, so whenever someone tries to connect to a cisco (Telnet) switch, I want the radius to authenicate them server. Is this possible?

  Yes it is possible as long as you configure your switches to authenticate to the Radius server. To achieve this, you must use a feature called AAA. This feature is compatible with the protocols such as Radius, GANYMEDE +, to name a few. The following link will give you an idea on how to set it up on switches IOS based specifically on the 3550:

  http://www.Cisco.com/en/us/partner/products/hw/switches/ps646/products_configuration_guide_chapter09186a00801a6b15.html

  Make sure that apply you the authentication list to the vty lines to ensure that telnet access is authenticated with the radius server. FOT based CatOS switches than the following link will be useful:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK642/technologies_tech_note09186a0080094ea4.shtml

• 3005 to multiple RADIUS servers?

  Is it possible to install groups in the 3005 to authenticate on the specific RADIUS servers?

  I wish:

  VPNGroup1 authenticate on RADIUS1 then

  VPNGroup2 authenticate on RADIUS2.

  I can tell the group to authenticate to a RADIUS server, but I have not found a way to tell the group what server to use.

  Hello

  Go in configure > user mgmt-> groups

  highlite group, click Server Auth button and then configure the RADIUS server, and it would only be used for this group.

  THX

  AFAQ

• RADIUS server problem

  Hi all

  I configured a radius server on my sbs2008 server.  I am able to test successfully, the ASA, but when I try to connect with the Anyconnect client I get a connection failure.  When I check the logs I see that the VPN is trying to authenitcate against the local database and not my RADIUS server evern if I set authentication server group.  I also rebooted the thought of the asa that was the issue.

  Here is my config:

  WebVPN

  port 444

  allow outside

  SVC disk0:/anyconnect-win-3.1.03103-k9.pkg 1 image

  enable SVC

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec

  internal OAC group policy

  OAC group policy attributes

  value of 192.168.2.2 WINS server

  value of server DNS 192.168.2.2

  VPN-tunnel-Protocol svc webvpn

  group-lock value OAC

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value OAC

  value by default-field OAC. LOCAL

  remote access to OAC tunnel-group type

  attributes global-tunnel-group OAC

  address vpnpool pool

  authentication-server-group OAC

  Group Policy - by default-OAC

  Thanks for any help,

  Leon

  Leon,

  Looks like your connection is down on the Group of the DefaultWebvpn tunnel. You must set the list of groups to choose

  OAC as a tunnel for the connection group. Here's what to be configured:

  WebVPN

  tunnel-group-list enable

  !

  tunnel-group OAC webvpn-attributes

  group-alias OAC enable

  Users will connect to the correct tunnel OAC group for authentocated of the radius server.

  Kind regards

  Bad Boy

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• RADIUS Auth Login and VPN is in conflict...

  Hello

  Im trying to setup a 7204 to authentication radius connection, even if the router is also configured with RADIUS for VPN access. How can I configure it for both using 2 raidus different servers? the connection through RADIUS works fine on another router, although this one does not have VPN access so there is no conflict.

  My config:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} rayon de serveur AAA groupe RADIUS_AUTH
  Server x.x.3.11 auth-port 1645 acct-port 1646

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} radius AAA authentication connexion networkaccess groupe local

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} groupe par défaut AAA autorisation exec RADIUS_AUTH if-authentifié

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} rayon-serveur hôte x.x.3.11 auth-port 1645 acct-port 1646 clé xxxxxx

  line vty 0 15

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}      login authentication networkaccess

  The line below is used for VPN authentication:

  RADIUS-server host x.x.8.12 auth-port 1812 acct-port 1813 key xxxxxx

  AAA of authentication ppp default local
  Ray of AAA to authenticate ppp vpdn group

  AAA authorization network default local
  RADIUS AAA authorization network vpdn group
  Group AAA authorization auth-proxy default RADIUS
  AAA accounting delay start
  accounting AAA periodic update 5
  start-stop radius group AAA accounting network default

  For some reason, it does not. I can't access the router and authenticate via radius x.x.3.11 server. I think there is a conflict between the VPN and authentication of connection but im not sure how to solve this problem.

  any help would be greatly appreciated.

  "ray of aaa of ppp authentication vpdn group.

  'radius of group' means 'take any server radius from the global list'.

  Change it to 'group mygroup' and boom, you give it a subset of radius servers

• Accounting session via radius or syslog AnyConnect?

  Hello

  Someone at - it a method of accounting deployed to save Anyconnect session details?  Are you a radius server or via recording messages to a syslog server?

  If Yes can help you with the appropriate configuration?  I seeks to save authentication successful and failed and duration of the session, connect and disconnect times.

  I've been playing with Anyconnect is authenticating to AD via ACS 5.1 but can't seem to get the accounting details, I need.  Similarly, I tried to catch the appropriate syslog messages but once again without much success.

  Thanks a lot for any input, St.

  What what you have configured for radius on ASA account management?

  You can paste the o/p of the aaa Server show and see the tunnel-group race

  Basically, all you need to define the radius server group and call this group under the tunnel-group settings.

  . - Configure the AAA server group.

  ciscoasa (config) # the RAD_SRV_GRP of the aaa-Server Protocol RADIUS

  output ciscoasa(config-AAA-Server-Group) #.

  . - Configure the AAA server.

  ciscoasa (config) #-RAD_SRV_GRP (inside) host 192.168.1.2 aaa Server

  ciscoasa(config-AAA-Server-Host) # key secretkey

  output ciscoasa(config-AAA-Server-Host) #.

  . - Configure the tunnel group to use the new configuration of AAA.

  ciscoasa (config) # tunnel - group ExampleGroup1 General-attributes

  ciscoasa (config) #accounting - server - group RAD_SRV_GRP.

  Once done, you can then establish a session and check the detailed accounting package on ACS 5.x range > monitoring and reports > catalogue > aaa protocols > radius account management.

  In case you don't see radius account management after following the above steps then please activate the RADIUS accouting and aaa debug ASA "debug". In this way, we can check whether or not ASA sends the details of the session accountinf to ACS.

  Kind regards

  Jatin kone

  -Does the rate of useful messages-

• Several points of access Cisco Aironet 1131AG and same SSID?

  We have several Cisco Aironet 1131AG, all wired devices on a switch (2560) Cisco L2 which is connected to the L3 switch (3550). We have assigned a VLAN for access point to the L3 switch which acts as a vtp Server (L2 switch is vtp client). All the ap will have a static ip address and all will have the same SSID and no security, and they will use several channels (e.g. 1,6,11).  They will work in 3 floors for a roaming wireless client. We not using any wireless controller.

  So my question is this: how to configure the same APs-all with a different ip address, can we use L3 switch to create the dhcp server to access points VLAN (pool for guests) and the rest of the static ip address for the ap? One of the ap can be WDS and on the same radius server local time with users without Cisco Secure ACS or similar controller or I did not understand this very well :-). I followed the guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where Abu Cisco ACS part is a problem, so I can use the same ap as a Local authenticator as a guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.

  Thank you very much...

  Well, just so you know, WDS, and local RADIUS authentication is necessary only if you use authentication on your wireless connection.  You say that you do not plan to use security, so it's not necessary.  However, I highly recommend at least using a simple WPA2-PSK to lock your connection, otherwise you might end up giving free Internet access at best and at worst you could give access to the computers and corporate servers.  If you want to reuse a 802. 1 x or WPA authentication method, then Yes, you can use an AP as RADIUS and to improve WDS Server authenticated to roaming, but this is much more limited than the use of a Cisco ACS.

  As for your other questions, Yes, your APs can all be configured the same except for at least three settings: IP address, hostname, and channel.  Configure your static IP addresses on the interface of the PA BVI1.  Do not place it on the Radio or Ethernet interfaces, because if one of these interfaces goes down, you lose the ability to configure the AP, so it's best to use the BVI1 interface.

  And Yes, configure a DHCP scope for your customers on your L3 switch is good design, or you can also use your DHCP server on a different subnet by using the command of support-ip address on the interface of L3.  I hope this helps!  Let me know if you need help to set all this up.

  Merry Christmas!

  Jeff